The photo shows one pattern, but the specification lists five SKUs: what exactly will arrive for order C-003-3

The buyer sees an elongated wooden composition in the photo: the ornament is assembled, the lines continue each other, the central part holds the gaze, narrow profiles form a complete contour. One item is added to the cart — C-003-3. It seems that one ready-made decorative element should arrive, which only needs to be applied to the facade and secured.

But the order includes MLD-003, N-408, N-409, K-020, and K-070. Instead of one clear item, the buyer receives a list of molding, two carved overlays, and two baguettes. What does this mean? Five physical parts? Five types of blanks? Full two-meter profiles? Already cut elements? An assembled composition on a base? A set without a diagram? The answer affects not only installation. The form of delivery determines packaging, the number of cargo spaces, space for dry layout, tools, the master's work time, and even the moment when painting can begin.

The C-003-3 set cannot be purchased based on a single photo. Before payment, you need to obtain an exact specification: the name of each component, article number, quantity, dimensions of supplied blanks, material, sanding quality, form of delivery, need for cutting, marking, and layout diagram. Only after this does it become clear what exactly is being paid for and what should arrive at the site.

The card confirms the overall size of the composition is 580 × 2050 × 30 mm, options in beech and oak, sanding "Standard" or "Prestige", basic beech preparation for enamel, and custom manufacturing. At the same time, the description calls the set a composition of three parts — two side rails and one overlay, while the composition block lists five article numbers. These formulations do not need to be "corrected" independently with guesses. They need to be translated into specific questions for the specification.

If you are going to buy a set of wooden decor C-003-3First, determine not only the place of application, but also the expected delivery result: a finished assembly, a marked set, cut elements, or a set of full-size profiles and overlays. The article will help you go through this path without accusations, haste, and costly rework.

Decor Set C-003-3

from 528.09 $

Go to Catalog

Short answer: what exactly needs to be confirmed before payment

C-003-3 is a composite decorative composition. One kit article combines several independent components that also exist as separate products. However, the presence of a component list does not yet answer the question of the form in which they will be delivered to the buyer.

Before payment, it is necessary to confirm in writing:

1. Whether C-003-3 is supplied assembled.

2. If there is no assembly, will the parts be cut to size.

3. Will K-020, K-070, and MLD-003 arrive at full length.

4. What quantity of each component is included in the specific specification.

5. How are the parts marked.

6. Is there a drawing or layout diagram.

7. What does the overall size of 580 × 2050 × 30 mm mean specifically for the selected surface?

8. Are the mounting template, base, backing, fasteners, and adhesive included?

9. Are all parts made from the same type of wood?

10. Does the sanding quality match across all components?

11. Where is the final trimming performed?

12. Who is responsible for the trial assembly before painting and gluing?

The main idea is simple: one product SKU does not necessarily equal one physically assembled part. But a list of five SKUs does not automatically mean five separate items. One long profile may be cut into several sections; one overlay may exist in different sizes; part of the composition may serve as a central or side unit. Therefore, the set cannot be counted "by eye."

Watch video ...

What is confirmed for C-003-3

The table separates facts from questions. Size, material, and sanding options are confirmed by the card. Assembly method, number of physical parts, and readiness of profiles for installation must be specified in the order.

On the product page you can view the composition of C-003-3 and check current options. But before payment, it's better to turn the card screen into a separate specification that can be opened upon receipt.

Our factory also produces:

Wooden finial L-088

from 28.91 $

Wooden ceiling rose R-004

from 4.39 $

Wooden rose R-005

from 5.73 $

Wooden Rosette R-024

from 3.42 $

Wooden rose R-027

from 4.39 $

Wooden rose R-051

from 6.10 $

Mirror frame RM-010

from 844.42 $

Wooden Rosette R-068

from 8.17 $

View Full Product Catalog

One kit SKU and five component SKUs — this is not a contradiction

The kit SKU is needed by the buyer: it denotes the entire composition, its overall appearance, dimensions, and commercial position. Component SKUs are needed by production, warehouse, calculation, and control. They allow understanding which profiles and carved elements make up the design.

Such a system has practical benefits.

Each part can be checked

If K-020 is listed separately in the statement, it can be matched with its own card, profile, and design. The same applies to K-070, N-408, and N-409.

A damaged component can be replaced or reordered

The ability to order separately does not mean automatic compatibility of any modification, but having an independent SKU simplifies identification.

Material and preparation can be coordinated

The buyer sees that the composition is not a monolithic carving from a single board. It is assembled from different types of wooden decor, and parameters need to be aligned.

Production completeness can be controlled

If one of the stated items is missing from the packaging or invoice, the issue arises before installation, not after gluing the remaining parts.

However, individual cards also create a risk. The buyer may decide that they need to purchase one piece of each item themselves and get C-003-3. This is an incorrect approach. A composite set is determined not by a simple set of names, but by quantity, size variants, cutting, and layout scheme.

Three parts or five items: why numbers cannot be compared directly

The description "two side rails and one overlay" refers to large visual or structural parts of the composition. The list MLD-003, N-408, N-409, K-020, and K-070 refers to the types of products involved in creating the pattern. These are different levels of description.

Imagine a door portal. Visually, it may consist of two vertical posts and a top finish. But the production list includes molding, baguette, two overlays, a base, and fasteners. Three large zones do not turn into six identical physical parts.

For C-003-3, the following logic is possible:

• a large part of the composition includes several items;

• one profile is used in several sections;

• the overlay is installed on top of the molding or baguette;

• The linear blank is cut into several segments;

• Part of the elements forms a common central node.

This explanation shows the principle but does not replace the official diagram. In the article, N-408 cannot be assigned as the left element, N-409 as the central one, or K-070 as the outer frame without a confirmed drawing. The roles of components are fixed in the specification and layout.

How to read the "Kit Contents" block

The composition line must answer at least seven questions:

If the line shows only the name and price, there is not enough information for installation. The buyer needs a document where the quantity is not hidden in the interface, and the dimensions refer specifically to the ordered configuration.

What does the overall size 580 × 2050 × 30 mm mean

The overall size helps match the composition to the surface. It shows the scale of C-003-3: the element is stretched vertically or horizontally depending on the application scheme, occupies a significant field, and has a pronounced relief.

But you cannot independently assign each letter the role of "width," "height," and "thickness" if the drawing is not open and the orientation is not confirmed. You need to request an image with labels A, B, and C.

The check is structured as follows:

1. Obtain drawing C-003-3.

2. See from which points 580, 2050, and 30 mm are measured.

3. Determine the orientation of the composition.

4. Overlay the dimensions on the facade at scale.

5. Check the free space at the edges.

6. Ensure that handles, hinges, cornice, and plinth do not intersect the relief.

7. Determine whether a base is required.

8. Check the opening of doors and drawers.

9. Coordinate the thickness of the decorative layer.

10. Record the final position on the installation diagram.

The number 2050 mm does not automatically mean the length of each profile. K-020 and K-070 may be supplied in their standard lengths and then cut to size. Or the kit may come pre-cut. This is one of the main ordering questions.

Is C-003-3 suitable in size: surface check

For a tall furniture front, it is not enough to compare the door height with 2050 mm. You need to measure the usable area — the section free of functional parts and adjoining elements.

Tall cabinet

From the total height, subtract the plinth, cornice, gap to the ceiling, handle line, decorative frames, and technological allowances.

Furniture Portal

Check not only the height but also the symmetry relative to the opening. The composition must be aligned to the axis.

Wall panel

Take into account sockets, switches, panel seams, baseboard, and top cornice.

Door

They check the hinges, lock, push handle, casing, and the impact zone of the door leaf against the wall.

Headboard

You need to match the decor with the mattress width, backrest height, bedside tables, and lamps.

Boiserie

The composition must fit into the panel module and support the overall rhythm of the moldings.

After taking measurements, you can check the set on the furniture facade through the project layout. This is especially useful when C-003-3 is adjacent to other frames and carved elements.

Four possible delivery forms

Until the delivery form is confirmed, the buyer needs to understand the main scenarios. Not to choose them independently, but to ask a precise question.

Scenario 1. Fully assembled composition

C-003-3 can be prepared as a single unit. Then the following are important:

• assembly base;

• final dimension;

• transport rigidity;

• weight;

• attachment points;

• possibility of drift;

• protection of protruding relief;

• surface readiness for finishing.

This option reduces operations on site, but requires large packaging and careful installation.

Scenario 2. Cut and marked parts

Components arrive separately, but cutting is done. The buyer needs a diagram with markings: top, bottom, left side, right side, central node.

Plus — fewer dusty operations. Risk — confusing parts or damaging prepared ends.

Scenario 3. Full-size profiles and separate overlays

Moldings and baguettes are supplied in standard lengths, and the installer performs cutting. This scenario requires:

• cutting maps;

• a suitable saw;

• stock;

• pattern control;

• space for long workpieces;

• a qualified craftsman.

Scenario 4. Mixed supply

Part of the composition may be assembled, and linear profiles supplied separately. Or overlays are prepared, but the baguette requires trimming. This format cannot be described with one word "set". A line-by-line list is needed.

In the order, one of the scenarios or an exact combination should be fixed. The wording "supplied as a set" is too general.

If C-003-3 arrives assembled

An assembled composition looks more convenient, but it has its own checks.

Substrate

You need to know what the components are held on. If the base is missing, how do the elements maintain their relative position?

Geometry

Measure the diagonals and the overall dimension before installation. A long composition should not be skewed.

Mounting

You cannot automatically glue a large assembled block the same way as a small overlay. The mounting scheme is agreed with the wall or furniture material.

Transportation

A size of about two meters requires rigid packaging. The number of pieces, orientation, and unloading rules are clarified.

Finishing

If the components are assembled before painting, you need to understand whether the internal corners and joints are accessible for primer and enamel.

Skid

They check the staircase, doors, elevator, corridor turn, and storage area.

A collected delivery does not mean readiness for immediate gluing. First, acceptance, size control, and dry fitting are performed.

If profiles arrive at full length

Full length provides freedom for adjustment but transfers responsibility for cutting to the site or workshop.

The buyer needs to receive:

• standard length MLD-003;

• standard length K-020;

• standard length K-070;

• the required number of blanks;

• map of useful segments;

• allowance for cutting;

• pattern direction;

• joint diagram;

• note which remnants are needed for re-checking.

It is especially important not to confuse the length of the overall composition with the length of the commercial profile. For example, a kit card may show a total size of 2050 mm, while the composition line shows linear footage of another standard length. This is not an error in itself: the extra part may be intended for cutting. But the buyer must understand what they will receive.

If parts are already cut

Ready-made cutting reduces the amount of work but increases labeling requirements.

Each part should ideally show:

• order number;

• article number;

• position on the diagram;

• orientation;

• node number;

• material;

• quality of preparation.

Before painting, parts are laid out on a flat surface. First, check the overall contour, then joints, central axis, distances between overlays, and compliance with dimensions.

If there is no marking, the set is photographed and labeled independently immediately after acceptance. It cannot be placed next to parts of another facade without separation.

If the delivery is mixed

The mixed format is logical in composite decorative projects: a large overlay may be ready, while a linear profile requires trimming to fit a specific surface. But it is the mixed format that most often creates confusion.

For each item in the list, a separate column is added:

Phrases in the table do not assign technology. They indicate what exactly needs to be filled in the agreed specification.

What to request in specification C-003-3

A good specification should be suitable for payment, acceptance, and installation.

Document header

• item C-003-3;

• order number;

• overall dimensions;

• material;

• sanding quality;

• preparation for finishing;

• deadline;

• delivery form.

Component list

For each row:

• name;

• article number;

• size;

• quantity;

• length;

• material;

• polishing;

• end condition;

• need for cutting;

• marking;

• number on the diagram.

Mounting part

• composition image;

• axes;

• distances;

• assembly sequence;

• base;

• recommended fixing method;

• glue application zones;

• need for temporary support;

• finishing procedure.

Logistics

• number of packages;

• packaging dimensions;

• marking;

• thread protection;

• acceptance procedure.

When requesting a document, you can use a commercial anchor request specification C-003-3 and list which columns you need.

Why specification is more important than a photo

A photograph answers the question "what does an idea look like." A specification answers the question "what to buy and how to assemble."

The photo does not show:

• the back side;

• the mounting base;

• individual joints;

• standard lengths;

• the number of repeating elements;

• the quality of sanding;

• markings;

• assembly order;

• stock;

• mounting method.

A professional order begins with visual selection but ends with a technical document. Without it, even a beautiful set remains a collection of expectations.

MLD-003 as part of the set: not just a long rail

MLD-003 belongs to linear trim. In the composition, it can define geometry, unite overlays, and create a calm frame line against which carved elements read more clearly. But merely mentioning MLD-003 does not show how many segments will be used and which ends need to be prepared.

Before payment, they clarify:

• the standard length of the supplied profile;

• the number of blanks;

• the number of working segments;

• the connection method;

• the profile orientation;

• position relative to N-408 and N-409;

• sanding quality;

• material;

• need for reserve;

• place of final cutting.

If MLD-003 arrives as a long plank, the installer must have equipment capable of making a clean, repeatable cut. If the profile is pre-cut, the marking and compliance with the scheme must be checked. Assembly cannot start with a molding just because it seems to be the "base." The sequence must be specified in the installation sheet.

N-408: separate item and part of the overall composition

N-408 has its own card and several options for size, material, and preparation. Therefore, the article name without modification does not guarantee that the buyer chose the exact size specified in C-003-3.

Before ordering, it is useful check the size of N-408 and then match it with the kit line. Checked:

• size modification;

• material;

• polishing;

• quantity;

• orientation;

• position number on the drawing;

• position relative to the axis;

• relief depth;

• method of adjoining to profiles.

N-408 cannot automatically be called an upper, lower, side, or central overlay without scheme C-003-3. A standalone card shows the product but does not define its role in a specific composition.

When a standalone N-408 card is especially useful

It helps compare confirmed dimensions, view the drawing, choose beech or oak, and understand preparation options. If one overlay is damaged, the article number facilitates identification. However, reordering is performed only after checking the batch and modification: the same name should not substitute for a full match of parameters.

N-409: similar category does not mean interchangeability

N-409 is also an independent carved element. A buyer may see similar styling between N-408 and N-409 and decide that one overlay replaces the other or that they can be swapped. Such a conclusion is dangerous.

The elements differ in dimensions, pattern, and role in the composition. For C-003-3, it is necessary to clarify the position of N-409 in the set According to the official scheme.

The check includes:

1. Item number on the drawing.

2. Thread orientation.

3. Distance to adjacent profiles.

4. Alignment of the central axis.

5. Relief height.

6. Material and polishing.

7. Quantity.

8. Mark whether a mirror flip is needed.

9. Method of fixation.

10. Coloring sequence.

N-408 and N-409 should not be stored in a common unsigned box. After receiving, each invoice is assigned a designation from the scheme.

K-020: narrow baguette requires precise cutting

K-020 is a narrow wooden baguette 11 mm wide. Its small size does not make it secondary. It is the thin profile that often forms a delicate line, separates a large ornament from the plane, and supports the rhythm of the composition.

Before assembly, you can view the narrow baguette K-020 and check the pattern. For set C-003-3, the following are important:

• exact modification;

• workpiece length;

• number of working segments;

• ornament direction;

• joints;

• miter angle;

• allowance;

• face orientation;

• position relative to K-070;

• Method of fixation.

Why a narrow profile is harder to notice in the specification

In the visualization, K-020 may look like a thin line. The buyer easily misses it in the list, and the installer starts assembling only large parts. As a result, the composition loses its calculated contour, distances change, and overlays seem randomly placed.

Why K-020 cannot be cut without a full layout

If you first cut the narrow molding to individual sizes and then find out that the overall axis is shifted, the short segments can no longer be returned to their original length. First, mark the entire dimension of 580 × 2050 × 30 mm on the base, then check the positions of large elements, and only after that refine the lengths of thin profiles.

K-070: a more pronounced profile sets a different scale

K-070 has a profile of 22 × 13 mm and protrudes more noticeably on the surface. It can perform a different visual function than K-020: creating the main carved line, frame, or accent area. But the specific position is determined by drawing C-003-3.

Before ordering, you should check the profile K-070 22 × 13 mm and clarify the length included in the kit.

For installation, the following are important:

• height and width of the profile;

• pattern direction;

• number of segments;

• the joint location;

• distance to the facade edge;

• transition to overlays;

• protection of the relief during pressing;

• method of processing the ends;

• compliance with the material of other parts.

K-020 and K-070 cannot be swapped

Both items belong to the wooden baguette category, but differ in cross-section and pattern character. Swapping will change the relief, line width, and mating with overlays. Even if both profiles physically fit on the surface, the composition will no longer match C-003-3.

If the project is created independently, it is useful to compare K-020 and K-070 in the wooden baguette category. For the finished C-003-3, comparison is needed not for replacement, but to understand the role of two different profiles.

How not to confuse a kit with a self-assembled set of parts

The buyer may see that all components are sold separately and try to assemble the composition cheaper or change dimensions without a project. This path requires caution.

The finished article C-003-3 combines:

• overall dimensions;

• visual composition;

• coordinated types of elements;

• commercial position;

• expected layout.

Self-selection of five articles does not guarantee:

• the required quantity;

• correct size options;

• sufficient length;

• a single breed;

• identical sanding;

• matching relief;

• exact position;

• economical cutting;

• conformity to the overall size.

Independent design is possible, but then it becomes a new composition, not an automatic repetition of C-003-3. It requires its own drawing and specification.

Beech or oak: the material is chosen at once for the entire set

Card C-003-3 offers beech and oak. The choice of wood species cannot be made only for the central overlay, leaving the profiles random.

Beech for enamel

Beech is suitable for opaque finishing. The basic configuration of the card indicates preparation for enamel. In such a composition, the color and texture of the lamellas are covered by the coating, and the main focus remains on the shape of the relief.

Check:

• identical preparation of all components;

• compatibility of primer and enamel;

• treatment of ends;

• accessibility of internal joints;

• necessity of intermediate sanding;

• painting order before or after assembly.

Oak for transparent or texture-emphasizing finish

Oak is chosen when the wood grain should participate in the image. Then especially important are:

• shade matching;

• direction of fibers;

• selection of parts from the same batch;

• toning test;

• careful trimming;

• absence of noticeable repair inserts.

The card suggests oak as a material, but the exact preparation and finishing option must be confirmed for each specification line.

Why mixing wood species is dangerous

Under opaque enamel, the difference can sometimes be visually hidden, but density, absorption, and behavior during processing differ. Under a transparent coating, the mixing of beech and oak is immediately noticeable. Therefore, the material is specified not only in the order header, but also next to each component.

"Standard" or "Prestige": the decision affects the entire installation cycle

The quality of sanding determines the amount of subsequent preparation. In a composite set, the error is especially noticeable: if a large overlay is prepared more carefully than a long molding, the surfaces may look uneven after painting.

Before ordering, it is useful choose "Standard" or "Prestige" and lock in one decision for the entire composition.

When choosing "Standard"

This option is suitable when the craftsman is ready to perform additional manual preparation, the project involves opaque finishing, and the budget accounts for sanding and local touch-ups.

When choosing "Prestige"

More thorough preparation reduces the amount of subsequent processing of complex relief. It is especially useful when:

• the composition is viewed from a close distance;

• the finish emphasizes the surface;

• access to internal areas is limited after assembly;

• installers have no time for lengthy manual finishing;

• a uniform level of preparation is required for all components.

Why you cannot mix two qualities randomly

Different roughness changes the absorption of primer and visual gloss. On long vertical decor, the transition may be noticeable under side light. If the kit card or composition lines show different qualities for individual items, this issue must be agreed upon before production.

First the material and sanding, then the color

Buyers often start with the enamel number or stain shade. For C-003-3, the order should be different:

1. Determine beech or oak.

2. Select "Standard" or "Prestige".

3. Check the preparation of each component.

4. Make a trial assembly.

5. Prepare a test sample of the coating.

6. Approve the color and gloss level.

7. Decide which surfaces are painted before installation.

8. Protect the ends and joints.

9. Perform the final finishing.

Color will not fix a mismatched profile, incorrect size, or missing element.

Which furniture is C-003-3 suitable for?

The overall dimensions make the composition noticeable. It requires sufficient flatness and a calm environment.

Tall cabinet with a solid front

C-003-3 can become a central vertical ornament on a solid door or side panel. Check the thickness of the front, hinges, handles, and deformation of the long panel.

Wardrobe portal

The decor can unite tall posts and the central part. An axial layout relative to the opening is needed.

Built-in furniture

The composition is matched with the niche, ceiling, baseboard, and opening gaps. Installation cannot be postponed until the cabinet is already wedged between the walls.

Large furniture door

The relief should not fall under the handle, mirror, hinge, or adjacent door. Also check the mass and balance of the panel, without making unconfirmed conclusions about the permissible load.

Decorative side panel

On the end of cabinet C-003-3 can work as a standalone vertical panel. The surface must be flat and wide enough.

C-003-3 on wall panel

Composite decor can be used not only on furniture. On a wall panel it creates a pronounced vertical module.

Checked:

• base material;

• flatness;

• position of electrical outlets;

• panel seams;

• baseboard;

• cornice;

• lighting;

• possibility of temporary fixation;

• access for finishing.

If the base is painted separately, the color and texture must be coordinated with the wooden parts. It cannot be assumed that the set includes a wall panel or backing unless specified in the specification.

C-003-3 for door

On the door, functional zones are critical. Before ordering, full-scale marking is done and the panel is opened.

Check:

• free play;

• handle zone;

• the lock;

• hinges;

• rebate;

• the casing;

• gap to the floor;

• impact against the wall;

• thickness of the decorative layer;

• opening direction.

The long ornament should be perceived as part of the panel, not as an overlay accidentally crossing the working elements.

C-003-3 for the headboard and interior panel

In the headboard, the composition can become a central vertical or repeat symmetrically. But the 2050 mm size should be matched with the overall height of the structure and the placement of the lights.

Important:

• bed axis;

• mattress width;

• height of nightstands;

• sockets;

• wall sconce;

• soft inserts;

• access for cleaning;

• attachment to the panel;

• safe absence of sharp protrusions in the contact area.

Such a scheme requires a separate project. Photo C-003-3 does not prove readiness for a specific headboard.

Classic boiserie and composite wooden decor

In boiserie C-003-3 must follow the wall module. First, a grid of moldings and axes is built, then carved elements are placed.

The composition can:

• occupy the central panel;

• highlight the pier;

• support the door portal;

• decorate a tall niche;

• become a paired element on opposite sides of the room.

If the decor is used twice, the specification is doubled only after checking the orientation. You cannot assume each component is mirrored without a drawing.

When C-003-3 won't fit

It's better to abandon the set or change the project if:

• the usable area is smaller than the required dimension;

• the facade is strongly divided by handles and fittings;

• the surface has a pronounced radius;

• there is no possibility to perform a dry layout;

• the installer is not ready to work with multiple profiles;

• the delivery form remains unknown;

• there is no drawing;

• the customer expects a monolithic finished panel;

• the room does not allow bringing in long workpieces;

• the budget does not account for preparation, installation, and finishing;

• the base material is not confirmed;

• Finishing is planned to begin before acceptance of all components.

  Why number components?

  The article number does not replace the position number. One K-020 can be used in several segments. Each working element is assigned a designation.

  Example:

  • MLD-003-L1;

  • MLD-003-R1;

  • K-020-A;

  • K-020-B;

  • K-070-V1;

  • N-408-C;

  • N-409-T.

  The letters in the example do not determine the actual position. The designation system is developed according to the official scheme. The main thing is that the same code is on the part, drawing, and packaging.

  Cutting map for long profiles

  If MLD-003, K-020, or K-070 are supplied in full length, a cutting map is made.

  Workpiece	Total length	Working segments	Cuts	Useful remainder
  MLD-003 №1	___ mm	___	___	___ mm
  K-020 №1	___ mm	___	___	___ mm
  K-070 №1	___ mm	___	___	___ mm

  The map answers three questions:

  1. Is one strip enough.

  2. Which segment is cut first.

  3. Does material remain for a test cut or repairs.

  You cannot cut profiles in a row from one edge without a map. The last needed section may be longer than the remainder.

  Direction of the ornament when cutting

  Carved baguette has a pattern. When flipping the adjacent segment, the pattern may go towards or change rhythm.

  Before cutting, mark on the back side:

  • start of the pattern;

  • direction;

  • the top;

  • front side;

  • Plot number.

  Particular attention is paid to paired verticals. They may require the same direction or a mirrored solution — this is determined by the project.

  Trimming and joints

  Composite decor shows the quality of installation precisely at the joints. A small gap between linear profiles can disrupt the continuity of the pattern.

  Before work, check:

  • equipment;

  • blade;

  • angle;

  • support for long workpiece;

  • clamp;

  • test cut;

  • cleanliness of the end face;

  • repeatability.

  You cannot first paint the entire batch and then check whether the saw handles it. One control cut before the finish is cheaper than repairing a finished profile.

  Basis for installation

  C-003-3 should not be considered an independent panel with a ready-made substrate. The base is determined by the project.

  Possible surfaces:

  • a furniture facade;

  • MDF panel;

  • wooden board;

  • wall panel;

  • door;

  • prepared wall.

  For each surface, the following differ:

  • adhesion;

  • rigidity;

  • permissible fastening;

  • thermal expansion;

  • need for primer;

  • possibility of through fixation;

  • risk of deformation.

  The question "what to glue C-003-3 with" cannot be resolved without determining the base and finish.

  What to buy together with C-003-3

  Additional items are selected after the specification is approved. Not every project requires the same set of materials.

  Position	What it is for	When to add
  Decorative Set C-003-3	Main composition	After checking the dimensions and form of delivery
  Carved Insert N-408	Replacement, additional unit, or custom project	Only per drawing
  Carved appliqué N-409	Component or separate decor	After checking the modification
  Wooden Molding K-020	Thin carved line	According to the cutting map
  Wooden molding K-070	More pronounced profile	Per specification
  Materials for installation C-003-3	Adhesive, preparation, and finishing	After determining the base
  Template	Position transfer	For complex layouts
  Test material	Coverage check	Before batch finishing
  Temporary stops	Part retention	According to installation technology
  Protective packaging	Storage and transportation	Until acceptance is completed

  The table does not promise that all listed items are included in the price of C-003-3. It separates the main product, components, and project resources.

  The adhesive is chosen after a dry fit

  In the catalog you can buy adhesive for wooden decor, but the material name does not replace compatibility testing.

  Consider:

  • wood species;

  • backside coating;

  • base material;

  • vertical position;

  • part size;

  • initial fixation time;

  • possibility of correction;

  • operating conditions;

  • need for mechanical support.

  Too fast setting is dangerous for a composition of several parts: the installer will not have time to adjust the axis. Too slow requires reliable temporary supports.

  Installation sequence

  The exact sequence should be in the project. The general logic is as follows:

  1. Accept the set.

  2. Check the specification.

  3. Perform a dry layout.

  4. Verify the dimension.

  5. Check the base.

  6. Prepare the template.

  7. Make a test of glue and finish.

  8. Perform cutting if needed.

  9. Reassemble the composition without glue.

  10. Transfer the axes to the surface.

  11. Install base elements according to the scheme.

  12. Add secondary profiles.

  13. Install overlays.

  14. Check the joints.

  15. Remove excess composition.

  16. Hold a technological pause.

  17. Perform final finishing.

  You cannot change the order just because one part seems visually central. The technological base and the visual center can be different elements.

  Finishing before or after assembly

  Both approaches have advantages and limitations.

  Finishing before assembly

  Advantages:

  • easier to paint the relief;

  • convenient to work in the workshop;

  • less risk of staining the furniture.

  Disadvantages:

  • the cut damages the coating;

  • glue may not work well on the finish;

  • joints require repair;

  • the shade of individual parts may differ.

  Finishing after assembly

  Advantages:

  • single color;

  • small joints are hidden;

  • the coating unifies the composition.

  Disadvantages:

  • it is harder to reach inner zones;

  • base protection is needed;

  • runs are more visible on vertical relief.

  Combined approach

  Part of the preparation is done before installation, the finish — after. The decision is made together with the painter and installer before production.

  How to accept C-003-3 upon delivery

  Acceptance begins with documents.

  They verify:

  • order number;

  • item C-003-3;

  • material;

  • sanding;

  • number of packages;

  • list of components;

  • packaging dimensions;

  • marking.

  Before opening, photograph the entire packaging, corners, edges, and impact marks. Then open each location step by step.

  Checking long profiles

  • straightness;

  • absence of breakage;

  • condition of the relief;

  • end faces;

  • length;

  • article number;

  • marking.

  Checking overlays

  • thin thread sections;

  • chips;

  • cracks;

  • size compliance;

  • back side;

  • material;

  • quality of preparation.

  Checking completeness

  Each item is marked in the list. If there are more physical parts than article lines, this is normal only if there is a clear quantity scheme.

  Official payment and delivery terms C-003-3 It is better to study before ordering, and the individual acceptance procedure should be confirmed in correspondence.

  What should be on the packaging

  Useful labeling contains:

  • C-003-3;

  • order number;

  • item number;

  • total number of items;

  • material;

  • sanding;

  • list of components;

  • warning about carved decor;

  • orientation of long profiles.

  If cut parts are inside, each must have its own code. Labeling should not be on the front surface or leave marks.

  What not to do immediately after receiving

  Sawing

  First, recount and lay out all parts.

  Painting

  Before painting, fix transport defects and check the composition.

  Gluing

  One missing profile can change the entire geometry.

  Discarding packaging

  It is needed until the acceptance is complete.

  Mixing with another order

  Similar baguettes are easy to confuse.

  Store vertically without support

  Long profiles may deform.

  Leave in wet area

  Wood and prepared surfaces require suitable storage conditions.

  Storage until installation

  Store components horizontally on a flat base. Use clean spacers between carved face surfaces.

  The room must be:

  • dry;

  • without direct sunlight;

  • without local heating;

  • without wet processes nearby;

  • protected from impacts;

  • spacious enough for laying out.

  Overlays are not placed under heavy profiles. Each group is stored with labeling.

  Main ordering mistakes

  Expecting a finished panel without confirmation

  The photo shows the composition, but not the form of delivery.

  Counting five SKUs as five parts

  The physical quantity is determined by the specification.

  Purchasing components individually on your own

  Dimensions and quantity may not correspond to C-003-3.

  Do not request a drawing

  Overall size without axes and location is insufficient.

  Mix beech and oak

  Finishing and texture will differ.

  Mix "Standard" and "Prestige"

  Surfaces will require different preparation.

  Accept 2050 mm as the length of each profile

  Overall dimension and commercial length are different parameters.

  Start with painting

  After it, it is harder to correct cutting and fix damage.

  Do not mark the segments

  Identical profiles lose position in the scheme.

  Glue from the center without technology

  The sequence is determined by the base and the project.

  Do not check the clearance

  The assembled composition may not fit through the doorway.

  Do not include installation in the budget

  The price of the product does not equal the full cost of the project.

  Full cost of project C-003-3

  The estimate may include:

  kit + design + packaging + delivery + cutting + preparation + glue + fasteners + finishing + installation + reserve.

  Expense item	Sum
  C-003-3	___ ₽
  Project and specification	___ ₽
  Delivery	___ ₽
  Layout	___ ₽
  Installation materials	___ ₽
  Soil and coating	___ ₽
  Installer's work	___ ₽
  Painter's work	___ ₽
  Reserve	___ ₽
  TOTAL	___ ₽

  The actual price of the kit is checked immediately before ordering. Do not carry over the old cost to a new estimate.

  Who C-003-3 is for

  The kit is suitable for a buyer who:

  • wants a large composite composition;

  • has sufficient surface area;

  • is ready to work from a drawing;

  • chooses beech or oak deliberately;

  • understands the difference between a kit and an assembled panel;

  • is ready to perform a dry layout;

  • agrees on the form of delivery;

  • includes installation and finishing in the budget;

  • orders all components at the same time;

  • wants to control the completeness of the set.

  Who should choose a different decor

  The other option is more reasonable if the buyer needs one small overlay, there is no space for layout, the craftsman does not work with linear materials, the surface is too small, or a fully finished panel with a confirmed base is required.

  In the catalog you can Buy decorative furniture overlays separately or choose another composite composition.

  Ready message to the manager

  Before issuing an invoice, you can send a request like this:

  "I plan to order C-003-3 for a surface measuring ___ × ___ mm. Please confirm the overall dimensions, material, grinding quality, actual quantity of each component MLD-003, N-408, N-409, K-020, and K-070, profile lengths, delivery form, need for cutting, presence of markings and assembly diagram. Also, please indicate whether the base, template, fasteners, glue, packaging, and delivery are included. I need a drawing with markings A, B, and C and a list of cargo items."

  Such a message covers most questions in one document.

  How to buy C-003-3 on STAVROS without uncertainty

  1. Open the product card and check the current price of the set.

  2. Measure the surface dimensions.

  3. Get a drawing.

  4. Overlay the dimensions 580 × 2050 × 30 mm.

  5. Choose birch or oak.

  6. Select "Standard" or "Prestige".

  7. Request specification.

  8. Confirm delivery form.

  9. Coordinate cutting layout.

  10. Get marking scheme.

  11. Select mounting materials.

  12. Calculate delivery.

  13. Prepare receiving area.

  14. Perform a dry layout.

  15. Only then start finishing and installation.

  FAQ: composition, delivery, and installation of C-003-3

  How many parts does C-003-3 consist of?

  The card describes the composition as three large parts, but the list includes five items: MLD-003, N-408, N-409, K-020, and K-070. This does not allow determining the exact number of physical parts on its own. One profile may be divided into several segments, and a large part may consist of several items. The exact quantity must be specified in the order specification.

  Why are individual items listed in the composition?

  Because the composition is assembled from independent types of wooden decor. The item numbers help identify the molding, overlays, and baguettes, and verify dimensions, material, and preparation. The complete item C-003-3 denotes the overall composition, while the component items denote its production composition.

  Will C-003-3 arrive assembled?

  The card and the list of components do not provide sufficient basis to promise a specific delivery format. Before payment, written confirmation must be obtained: ready assembly, cut parts, full-size profiles, or a mixed format.

  Are MLD-003, N-408, N-409, K-020, and K-070 included in the price?

  They are listed in the composition of the set, but the commercial amount and exact completeness must be checked in the current card and invoice. The specification must show which items are included in the price of C-003-3 and what is paid separately.

  What does the size 580 × 2050 × 30 mm mean?

  This is the confirmed overall dimension of C-003-3. To understand the orientation and purpose of each number, a drawing with designations A, B, and C is needed. 2050 mm cannot be considered the length of each individual profile.

  Are K-020 and K-070 supplied in full length?

  This needs to be clarified in the order. Both articles are linear moldings and have their own product cards, but the set may include full blanks, pre-cut pieces, or another format.

  Can the length of the composition be changed?

  The possibility of changing the overall size is not confirmed by the mere fact of a composite structure. Any adjustment affects the number of profiles, the placement of overlays, and the pattern. A separate calculation and project approval are required.

  Is a backing needed for C-003-3?

  The product card does not automatically count the backing as part of the set. The base can be a furniture front, panel, door, or another prepared surface. If a separate board or mounting base is required, it needs to be included in the specification.

  Is a mounting template included?

  The availability of the template should be confirmed before payment. If it is not included, you can order a project layout or prepare a full-size template according to the approved drawing.

  Can all parts be ordered in oak?

  The C-003-3 product card offers oak as a material option. However, in the specification, you need to check the material of each line to ensure that the molding, overlays, and baguettes are coordinated.

  What to choose — "Standard" or "Prestige"?

  The choice depends on the finish and the craftsman's readiness to perform manual touch-up. For complex carving and close viewing, more thorough preparation reduces the amount of subsequent processing. The main thing is not to mix qualities randomly within one composition.

  Can I order beech under enamel?

  Yes, the base configuration of the beech in the card is specified with preparation for enamel. The finish coating and its inclusion in the order need to be clarified separately.

  Can I order oak with a transparent finish?

  Oak is suitable for projects where texture matters, but the specific preparation and coating system need to be agreed upon. It is advisable to do a test on a sample from the same batch.

  Are N-408 and N-409 interchangeable?

  There is no reason to consider them interchangeable. They have different sizes, patterns, and intended roles. The position of each overlay is determined by scheme C-003-3.

  Can I buy N-408 separately?

  N-408 has a separate card. But to replace component C-003-3, it is necessary to check the dimensional modification, material, sanding, and batch.

  Can I buy N-409 separately?

  Yes, N-409 is presented as a separate product. The matching of the article number does not cancel the verification of the specific size and preparation.

  What is the difference between K-020 and K-070?

  K-020 is a narrow baguette with a width of 11 mm. K-070 has a profile of 22 × 13 mm and a more pronounced relief. They perform different roles and should not be swapped without a new project.

  Can C-003-3 be assembled from independently purchased components?

  Technically, you can create your own composition from these items, but it will not automatically become C-003-3. Correct dimensions, quantities, lengths, cutting, and a scheme are needed. It is easier to order a kit with a confirmed specification.

  What should be used to glue C-003-3?

  The adhesive is selected based on the base material, wood species, finish, component size, and operating conditions. First, perform a dry layout and a compatibility test.

  Is mechanical fastening required?

  This depends on the base, dimensions, delivery form, and installation project. You cannot assign only adhesive or only mechanical fixation without checking the structure.

  Can the parts be painted before assembly?

  Yes, if the coating technology and adhesive assembly allow it. But first, you need to perform a control cut and dry assembly. The finish coating should not become the first test of component compatibility.

  What to check upon receipt?

  Check the order number, item code, material, sanding, number of packages, component list, profile lengths, condition of threads, ends, and markings. Do not discard the packaging until the full layout is complete.

  What to do if one component is missing?

  Stop cutting and installation, photograph the received composition, verify documents, and contact the seller. You cannot replace the missing profile with a random analogue.

  What to do if profiles are not signed?

  Match them with the cards and diagram, then assign your own designations. If identification is ambiguous, request confirmation before cutting.

  How to store the kit before installation?

  Horizontally on a flat, dry surface, separating carved parts with clean spacers. Long profiles are supported along their entire length; overlays are not pressed down with heavy blanks.

  Can C-003-3 be used on a wall?

  Such a scenario can be considered if the dimensions, base, and mounting diagram are suitable. The kit does not automatically include a wall panel.

  Will C-003-3 fit a cabinet?

  Yes, a tall front or side panel can be a suitable base, but you need to check the usable area, hinges, handles, opening, and thickness of the decorative layer.

  Will the kit fit a door?

  Only after checking the lock, handle, hinges, rebate, casing, and free movement of the door leaf. A full-size template is mandatory for a complex door.

  How long does installation take?

  The exact time depends on the delivery form, cutting, base, preparation, and finishing. The product card does not confirm a universal installation duration.

  Where can I see the current price for C-003-3?

  In the kit card. Price, time, and availability are variable parameters, so they should be checked before ordering.

  Where can I see other compositions?

  In the category you can view individual and composite overlays and choose a solution for a different size or task.

  Is a design project needed?

  For a simple prepared surface, a precise drawing may be enough. For a cabinet, portal, door, boiserie, or repeating compositions, a project reduces the risk of errors and helps obtain an installation list.

  Control checklist before payment

  • C-003-3 is specified without error;

  • total size confirmed;

  • drawing received;

  • orientation is clear;

  • surface measured;

  • useful field checked;

  • beech or oak selected;

  • "Standard" or "Prestige" selected;

  • preparation of all components agreed;

  • quantity of MLD-003 specified;

  • quantity N-408 specified;

  • quantity N-409 specified;

  • quantity K-020 specified;

  • quantity K-070 specified;

  • profile lengths specified;

  • delivery form fixed;

  • cutting distributed;

  • marking agreed;

  • assembly scheme received;

  • base determined;

  • glue and fasteners are selected;

  • Finishing agreed upon;

  • packaging is described;

  • number of pieces is known;

  • delivery is calculated;

  • a place for dry layout is prepared;

  • persons responsible for installation are appointed.

  Final conclusion: they buy one C-003-3, accept the entire list

  C-003-3 attracts with a solid pattern, but its commercial unit and physical delivery may be arranged differently. One kit item combines molding MLD-003, overlays N-408 and N-409, baguettes K-020 and K-070. Five names in the composition do not give the right to independently assign five parts, and the description of three parts does not cancel the production list.

  Before payment, you need to get a specific answer: what will arrive assembled, what will be cut, which profiles will retain full length, how many units are included in each line, how they are marked, and where the diagram is. The overall dimension 580 × 2050 × 30 mm is checked on a full-size template. Beech or oak, "Standard" or "Prestige", preparation for enamel, cutting, glue, and finishing are agreed for the entire composition, not for one noticeable overlay.

  Upon receipt, the kit is first photographed, recounted, and laid out without glue. Only when the pattern matches, dimensions are confirmed, and all components have taken their places, can you proceed to trimming, painting, and installation.

  STAVROS company offers C-003-3 as a ready-made commercial composition, individual carved overlays, wooden baguette, installation materials, and a design layout service. This approach allows you to buy not an abstract ornament from a photo, but a clear set with a verifiable specification, controlled delivery, and predictable assembly.