Buy a round MDF tabletop: thick ST-023 670 mm or shaped ST-027 660 mm — which to choose

When a buyer wants to purchase a round MDF tabletop for a compact table, coffee table, or ready-made base, models ST-023 and ST-027 seem almost identical. The diameter of the first is 670 mm, the second is 660 mm. The difference of just 10 mm hardly changes the usable area, but the thickness, edge profile, materials, and character of the finished item differ so much that accidentally replacing one model with another completely changes the table's appearance.

ST-023 measures 670 × 670 × 65 mm and is made of MDF for custom finishing. It is a smooth round tabletop with a very thick edge: it appears monolithic, minimalist, and noticeable even on an open or thin base. ST-027 measures 660 × 660 × 30 mm. Its main difference is a shaped classic profile and the option to choose not only MDF for enamel but also combined versions with a solid rim and natural beech or oak veneer.

As of the check on July 21, 2026, the MDF version of ST-023 cost 6,540 rubles, and ST-027 made of MDF cost 7,120 rubles. The difference was 580 rubles. Therefore, the choice cannot be reduced to price or diameter. The buyer essentially decides whether they need a table with a thick smooth edge 65 mm thick or a thinner shaped tabletop 30 mm thick, which better matches a carved base and a finish with visible wood grain.

The following are discussed: surface area, edge proportions, MDF and veneer, opaque enamel and transparent finish, STL-023 and STL-027 bases, final table height, overhang, stability, mounting, edge protection, use near a sofa, in the living room, hall, and commercial interior, typical mistakes, and purchase package. The article does not promise unverified load capacity, moisture resistance, or universal compatibility: these parameters depend on the entire structure.

Buy ST-023 65 mm thickBuy shaped ST-027View all tabletops

MDF tabletop ST-023

from 85.89 $

Tabletop ST-001 from MDF

from 152.53 $

Go to Catalog

ST-023 or ST-027: confirmed characteristics

The comparison table immediately shows: diameter is the weakest selection criterion. With a difference of only 10 mm, both tabletops provide a similar work surface. However, the edge of ST-023 is 35 mm thicker, while ST-027 offers a shaped profile and options with a natural wood texture. Therefore, the article should lead the buyer not to a "larger tabletop," but to the appropriate construction.

Watch video ...

Why a diameter of 670 and 660 mm makes almost no difference

The diameter difference is 10 mm, which is only 5 mm in radius. If you place two round templates on top of each other, the outer contour of ST-023 will extend beyond ST-027 by only a narrow strip. In a room, next to a chair, or against the background of an under-table, this difference is almost imperceptible.

The area of ST-023 is approximately 0.353 m², the area of ST-027 is about 0.342 m². The difference is close to 0.011 m², or about 3.1%. The buyer does not get significantly more space for items by choosing a diameter of 670 mm instead of 660 mm.

The practical conclusion is simple: measuring free space is still necessary, but the debate between 660 and 670 mm rarely decides a purchase. The height of the finished table, edge shape, base type, and finish have a much greater impact.

Our factory also produces:

Mirror frame from MDF RM-035

from 191.78 $

MDF Mirror Frame RM-036

from 268.24 $

ST-020 countertop

from 264.03 $

Top ST-020-1

from 197.64 $

MDF Mirror Frame RM-054

from 240.20 $

ST-027 countertop

from 93.40 $

Top ST-030

from 457.08 $

Top ST-015

from 167.82 $

View Full Product Catalog

Usable surface area: what 0.353 and 0.342 m² mean

Calculating the area helps eliminate the subjective feeling that the ST-023 is significantly larger. A difference of about three percent does not turn a compact tabletop into a large dining table and does not change the furniture category.

When placed next to a sofa or armchair, what matters more than an extra five millimeters in radius is the height, access to the surface, and distance to the passage. In a hall or waiting area, it's the ratio of the tabletop to the base and surrounding furniture.

Area cannot be translated into a promised number of seats or items. Convenience depends on the table's purpose, height, base, and actual usage scenario.

Thickness 65 or 30 mm: the main visual choice

The ST-023 is 35 mm thicker than the ST-027. The ratio of 65 to 30 is approximately 2.17. From the side, this difference is immediately visible: the edge of the ST-023 becomes an independent volume, while the profile of the ST-027 remains thinner and emphasizes the contour.

A thick tabletop helps visually balance thin or widely spaced supports. On a three-leg base, a voluminous circle feels denser and more confident. In a small room, such an edge may, on the contrary, look heavy.

The shaped edge of the ST-027 works differently. It does not try to show maximum thickness but creates a transition of light and shadow. It is the profile that connects the tabletop with the carved base, classic furniture, and finishes with patina or tinting.

Why greater thickness does not mean confirmed load capacity

Thickness affects appearance and geometry, but by itself does not prove that ST-023 can withstand 2.17 times the load. Such a conclusion would require testing the entire system: the tabletop, fasteners, underframe, and connecting nodes.

The stability of a round table is determined by the base diameter, leg placement, overhang, height, fastening quality, and load distribution. A thick edge may look massive, but it does not replace calculation.

Before assembly, it is useful to study how to secure the tabletop to the underframe, and coordinate the specific scheme based on the selected parts.

The price difference between MDF versions is 580 rubles

As of the check date, ST-023 in MDF cost 6,540 rubles, ST-027 in MDF cost 7,120 rubles. The surcharge for the second model was 580 rubles. This difference is small compared to how noticeably the profile and character of the finished table change.

ST-023 offers a significantly thicker smooth edge. ST-027 has a shaped profile and a wider choice of materials, including combined options with veneer. Therefore, the first model cannot be considered more advantageous solely due to its lower price.

The current price should be checked before publishing the article and placing an order. The prices in the text reflect the state of the product cards as of July 21, 2026, and not a permanent commercial offer.

ST-023: round MDF tabletop with a thickness of 65 mm

What the customer buys

ST-023 is a round tabletop measuring 670 × 670 × 65 mm made of MDF for custom finishing. It is purchased not for the extra ten millimeters of diameter, but for the thick, smooth, and minimalist silhouette.

The model is suitable for projects where natural wood texture is not required, and the color must match the underframe, furniture, panels, or other painted joinery.

How the thick edge works

The 65 mm thick edge is clearly visible at eye level when the table is placed next to a sofa, armchair, or in a walkway area. It creates a sense of dense furniture volume even with a diameter of only 670 mm.

Contrasting edge paint enhances the mass, while monochrome enamel unifies the top and edge. The final effect is checked on a sample and under working lighting.

When ST-023 may be excessive

In a small room, on a very thin base, or next to lightweight furniture, the 65 mm edge can appear heavier than the entire interior. In that case, a thinner ST-027 or another model from the category would be more appropriate.

The full-size template should be evaluated not only from above but also from the side: it is the side view that reveals the main difference of ST-023.

Why ST-023 cannot be called a solid wood tabletop

In the old description from the sitemap, ST-023 was listed as a solid wood product, but the current product information indicates MDF material. Therefore, the correct wording is a round tabletop ST-023 made of MDF for custom finishing.

You cannot attribute beech, oak, solid wood, or natural wood texture to the model. Such words create false expectations in the buyer regarding the material and finishing method.

MDF here is not a drawback. It helps achieve a smooth surface for opaque enamel and assemble a minimalist painted table. Accuracy of description is important, not an attempt to artificially elevate the material's status.

Smooth volumetric edge ST-023: when it works best

A smooth edge suits modern, transitional, and minimalist interiors. It does not conflict with an expressive base and allows emphasis on color, proportion, and thickness.

In a solid color finish, the tabletop can look like a solid geometric disc. This effect is especially noticeable on an open base, where the underside of the tabletop and the edge are clearly visible.

If the base is already decorated with carving, a thick smooth top can provide the necessary contrast. But before ordering, you need to check whether the 65 mm volume overwhelms thinner supports.

ST-027: shaped round tabletop 30 mm thick

Profile instead of massiveness

ST-027 measuring 660 × 660 × 30 mm looks thinner but not simpler. The shaped edge creates chiaroscuro and connects the top with classic furniture, carved legs, and a decorative base.

A thickness of 30 mm lightens the silhouette next to a sofa or armchair. The table does not turn into a heavy disc, although the usable area almost matches the ST-023.

MDF version for enamel

The basic ST-027 version made of MDF is suitable for opaque painting. In this case, the decorative profile is read through shadows rather than wood texture.

Enamel allows you to connect the tabletop with painted STL-027, panels, doors, or furniture. Color and gloss are checked on a sample.

Combined options with veneer

For ST-027, versions are confirmed where MDF is combined with a solid wood rim and natural beech or oak veneer. Such versions cannot be called solid wood, but they provide visible wood texture.

The veneered tabletop is suitable for clear lacquer, tinting, or other finishes that preserve the material's pattern. The specific composition of the selected version is clarified in the product card.

Beech or oak veneer for ST-027

Beech veneer is chosen when a calmer and more even wood base is needed. It can be matched with a beech underframe or furniture if the shade and finish are coordinated using samples.

Oak veneer is appropriate when the texture should become part of the table's image. The oak pattern is especially noticeable on a round horizontal surface and can complement doors, panels, stairs, or other oak furniture.

You cannot expect the veneer to automatically match the color of an existing item. The species, tone, gloss, and grain direction are checked before ordering.

Shaped profile ST-027 and classic pedestal

The shaped edge creates a transition between the horizontal plane and the side surface. This transition makes the tabletop visually thinner but adds decorative detailing.

On a carved pedestal, the profile helps assemble a unified classic piece. A smooth thick ST-023 next to such a base will give a more contrasting and modern result.

If you need a matching set specifically, you can buy a carved pedestal STL-027, but check the mounting points, required overhang, and actual installation diagram before ordering.

Which model to choose for a specific task

What to choose for opaque enamel

Both models are available in a basic MDF version and can be considered for opaque finishing. Therefore, the material itself does not determine the choice: you need to decide which profile should remain after painting.

On ST-023, the enamel emphasizes the smooth edge with a thickness of 65 mm. On ST-027, it emphasizes the shaped edge with a thickness of 30 mm. The same color will yield two different items: a dense geometric disc or a thinner classic tabletop.

The preparation of the end, primer, enamel, and finish are coordinated as a single system. A random coating may poorly show the profile or require more preparation than the customer expected.

What to choose for a clear lacquer or tint

ST-023 should not be offered as a countertop with a natural wood texture based on the current card. For a clear finish, consider the corresponding veneered versions ST-027.

Beech or oak veneer preserves the material's pattern but does not turn the product into solid wood. It is important for the buyer to understand the composite construction and choose it consciously.

A clear finish requires coordination between the countertop and the base. Samples are viewed together because the same species name does not guarantee a complete tone match.

ST-023 and three-leg base STL-023

The manufacturer directly links ST-023 to a model that can be purchased as a three-leg base STL-023. The base size is specified as 524 × 460 × 725 mm. Three legs create a recognizable silhouette, and a thick countertop helps balance the open base.

Product connectivity does not eliminate the need to check assembly. It is necessary to confirm attachment points, actual overhang, stability, finishing order, and final height. It cannot be assumed that any round countertop with a diameter of 670 mm automatically fits any three-leg base.

A detailed analysis can be continued in the article about how to choose a round tabletop for STL-023 and check the stability of a three-legged structure.

ST-027 and carved table base STL-027

STL-027 is shown among related products for ST-027. The shaped profile of the tabletop logically continues the carved character of the base and helps to assemble a coffee or side table in a unified classic style.

Before ordering, you need to check the mounting points, required overhang, and attachment method. The article does not guarantee universal compatibility without checking the current product cards.

For such a composition, you can choose a carved table base for a coffee table and then coordinate the MDF version for enamel or the veneered version ST-027.

How tabletop thickness changes the final table height

Thickness is part of the overall geometry of the item. If the base has a fixed height, replacing a 30 mm tabletop with a 65 mm one raises the top surface by 35 mm, provided the mounting scheme does not change.

For the STL-023 base with a height of 725 mm and the ST-023 top with a thickness of 65 mm, the simple arithmetic sum is 790 mm. This is a preliminary geometric estimate without considering mounting nodes, thrust bearings, recesses, or fastening features.

Before purchasing, the height is compared with the table's purpose, furniture, and user seating. The 790 mm cannot be automatically considered the final certified product height without confirmation from the assembly diagram.

How to calculate the overhang of a round tabletop

Overhang is the distance from the outermost point of the base to the edge of the tabletop. For a round top, it is evaluated in several directions because the base may be three-legged, four-legged, or carved and may not have a circular plan.

Too small an overhang makes the supports visually cramped, while too large an overhang increases leverage and can impair stability. A universal value cannot be given without a drawing.

It is most convenient to overlay the base plan on a circle with a diameter of 660 or 670 mm. This shows how the tabletop extends over each support and where the attachment points are located.

How to check the stability of a round table

Stability depends on the footprint, height, center of gravity position, overhang, and fastening quality. Nearly identical diameters of ST-023 and ST-027 do not guarantee identical behavior on different bases.

A three-legged base does not wobble due to floor unevenness in the same way as a system with four points, but this does not mean automatic stability with any overhang. A carved base also requires geometry verification.

Before final finishing, a test assembly is put together and checked on a level surface. Only after this are the fasteners and coating approved.

How to secure an MDF tabletop

The fastening method depends on the underframe, thickness, embedded elements, and disassembly requirements. It is not possible to recommend a single screw or universal length without data on the structure.

For MDF, the correct direction of fasteners, hole depth, and absence of penetration to the front surface are especially important. The shaped profile ST-027 additionally limits the areas where fasteners can be placed.

Before installation, it is worth selecting glue, fasteners, and finishing materials and coordinating them with the furniture maker. The countertop is not fastened in a random way just because it looks thick.

How to protect the MDF edge from moisture

An MDF countertop requires a complete finishing system. Special attention is paid to protecting the edge, bottom surface, holes, and fastening points. Opaque enamel should be perceived as part of the technology, not just as a chosen color.

The article does not refer to ST-023 or ST-027 as a moisture-resistant kitchen countertop. These models should not be promoted for use under a sink, cooktop, outdoors, or for a garden table.

Spilled liquid is removed without prolonged contact with the surface, and care is chosen based on the finish coating. Specific products are coordinated with the finisher.

How the edge shape changes color perception

On the smooth end of ST-023, the color reads as a large continuous band 65 mm high. A dark or contrasting shade enhances heaviness, while a light shade close to the tabletop makes the volume calmer.

The shaped edge of ST-027 breaks up color with light and shadow. Even a single-color enamel shows the profile, while patination or veneer tinting enhances the relief.

Choosing color only from a small sample is not enough. You need to imagine how it looks on a large horizontal surface and around the entire circumference of the end.

Table next to a sofa or armchair

Next to upholstered furniture, height, surface access, and clear passage are important. A 10 mm diameter difference is almost unnoticeable, but the 65 mm end is in the field of view and makes ST-023 visually denser.

ST-027 with a thickness of 30 mm combines more easily with elegant legs, a chair on high supports, and classic furniture. The shaped profile reads well from a seated level.

The template is placed not only on the floor but also at the intended height. This way, the buyer assesses the actual volume of the table, not just one circle from above.

ST-023 or ST-027 for the living room

ST-023 suits a living room with a large sofa, expressive geometric shapes, and painted furniture. The thick top can contrast with an open base and support a modern composition.

ST-027 connects better with carved details, classic panels, natural texture, and a coffee table format. In veneer, it supports wooden furniture; in enamel, painted furniture.

The choice depends not on the conventional name of the style, but on the existing thicknesses, profiles, and materials in the room.

Countertop for the hall and waiting area

In the hall, a round table helps organize a free furniture group without sharp corners. ST-023 provides noticeable volume and reads well in a spacious room. ST-027 looks lighter and more decorative.

For the waiting area, check the passage, stability, and usage mode. A surface cannot be assigned for intensive commercial use without agreed-upon finishing and fastening.

If the table should work as an accent, ST-023 emphasizes the scale of the end. If attention should remain on the carved base and surrounding furniture, ST-027 often looks more cohesive.

Coffee or side table in a cafe and hotel

ST-027 directly matches the coffee or side table scenario: the shaped edge, 30 mm thickness, and associated carved base create a decorative item for the lobby, room, or waiting area.

ST-023 can be used where a more graphic, painted, and massive object is needed. However, the finish and fastening must correspond to frequent use.

A commercial space requires separate approval of stability, maintenance, and repairability. One countertop card does not cover these issues.

What to choose for a modern interior

A modern interior does not automatically require a smooth countertop, but ST-023 fits more easily into laconic geometry. The thick circle creates a clear silhouette without additional ornament.

ST-027 can work in a modern space as a contrasting classic detail, especially in solid-color enamel. But its shaped profile must be supported by at least one adjacent element.

The practical choice is based on the thickness of the facades, the shape of the supports, and the color of the furniture, not on an abstract style label.

What to choose for a classic interior

ST-027 is more suitable for a classic project due to its shaped edge and veneer options. It is associated with carved aprons, wooden panels, and profiled furniture.

ST-023 can create a strong contrast: a smooth thick top on a decorative base. This technique is appropriate if the designer intentionally combines modern volume with a classic support.

To ensure the table does not look randomly assembled, the profile of the tabletop and apron should be evaluated together in a visualization or front sketch.

How to choose for a small room

In a small space, a diameter of 660 or 670 mm is almost the same, so saving space by choosing ST-027 just because of ten millimeters is pointless.

However, a thickness of 30 mm really makes the silhouette lighter. ST-023 with a 65 mm edge can visually take up more space, especially in a dark finish and next to low furniture.

The solution is checked with a side template: a circle from above does not show how dense the finished table will be.

Tabletop for a new furniture project

When designing from scratch, first choose the character of the table: a smooth solid top or a shaped decorative one. Then select the base, height, overhang, and finish.

ST-023 is convenient for a project on STL-023 and opaque enamel. ST-027 is for a side or coffee table on a carved base and for options with visible texture.

To avoid randomly assembling parts, you can select a tabletop and furniture base in the same product group and check the cards in advance.

How to select a tabletop for an existing base

Measure the existing base at its extreme points, height, and mounting area. Then overlay a circle of 660 or 670 mm on the plan. The diameter difference is small, but the profile and thickness may conflict with the supports.

Check whether the shaped edge covers the mounting area and whether the 65 mm end looks heavier than the base. The attachment points must fall into suitable areas of the tabletop.

If compatibility is not confirmed, it is better not to make a conclusion based on a photo. A drawing or manufacturer consultation is needed.

Self-assembly of a table: a ready-made tabletop or a random blank

The finished ST-023 or ST-027 already has a specific diameter, thickness, and profile. This simplifies design compared to a random slab that still needs to be precisely cut, processed around the circumference, and prepared for finishing.

But a ready-made element does not turn assembly into a mechanical connection of two parts. Checking overhang, height, stability, fastening, and finish is still necessary.

The full commercial route is revealed by the material on how how to assemble a table from a tabletop and a base, without accidentally ordering incompatible elements.

How to choose a round top for three supports

A three-leg base creates an expressive pattern and requires precise centering of the tabletop. Even a slight offset becomes noticeable due to the difference in overhang between the supports.

ST-023 is linked to STL-023 and visually balances the open base with a thick edge. Before fixing, mark the center of the circle and the actual center of the underframe.

Three supports cannot be considered sufficient for any load just by their number. Geometry and connections are checked in the assembly.

How to choose a top for a carved base

A carved underframe already contains a lot of plasticity, so the tabletop edge should either continue this language or deliberately contrast with it.

ST-027 with a shaped profile creates a cohesive classic composition. ST-023 provides a more modern smooth volume, but may draw attention to the thickness.

Both approaches are only acceptable after comparing the front silhouette and side view.

How to account for the bottom surface of the tabletop

The bottom plane is more visible than it seems, especially on a coffee table, open underframe, and furniture next to an armchair.

For ST-023, the finish of the bottom surface must be coordinated with the thick edge so that the large volume does not look unfinished. For ST-027, the neatness of the shaped profile transition is important.

Mounting holes and fasteners must not damage visible areas. Their position is marked before finishing.

How to choose a color for the underframe

The same color for the top and base makes the table calmer, while a contrasting one emphasizes the structure. On ST-023, the contrast is especially noticeable due to the 65 mm edge.

ST-027 in veneer can be combined with a beech or oak underframe, but samples are compared side by side. Different batches of wood and different tinting systems produce differences.

If the underframe is already painted, the color code and a real sample are more useful than a photo on the screen.

Matte, satin, or glossy surface

Gloss level affects the perception of the round plane and profile. Gloss shows reflections and possible unevenness more strongly, while a matte surface makes the volume calmer.

On ST-023, the glare passes along the wide smooth end. On ST-027, light is broken by the shaped profile, so the relief reads differently.

The specific finish is chosen as part of a confirmed finishing system, not just based on decorative preference.

How to coordinate the tabletop with the floor and carpet

A round table often stands on a carpet or next to an expressive floor covering. Thick ST-023 creates a heavier visual support over the floor pattern.

ST-027 with a thin edge leaves more attention to the base and carpet. The veneered version can support the wood tone of the floor but should not accidentally blend with it.

Color and scale are checked on a collage or in a visualization with real materials.

How to account for free passage around the table

A diameter of 660–670 mm requires space not only for the tabletop itself but also for movement nearby. A difference of 10 mm has almost no effect on the passage.

Much more important is the placement of supports, height, and usage scenario. A table next to the sofa should not interfere with seating, and in the hall, it should not cross the main traffic path.

A full-size circle is laid out on the floor with tape and the room is checked in actual use.

How to account for doors, drawers, and adjacent furniture

A round tabletop can overlap the opening path of a cabinet, wardrobe, or drawer, even if it visually fits.

ST-023 and ST-027 are almost identical in diameter, so replacing one with the other will not resolve the conflict with furniture. A change is needed.

How to prepare a technical specification for a furniture maker

The specification includes the article number, exact size, material, finish, base, final height, and required disassembly.

For ST-023, MDF and a thickness of 65 mm are separately specified. For ST-027, either MDF or a specific veneered option and a shaped profile.

A mounting diagram, overhang plan, and color samples are attached to the specification. The wording "round tabletop about 670 mm" is insufficient.

How to calculate the total budget for a table

The price of the countertop is only part of the estimate. You need to add the underframe, finishing, fasteners, assembly, packaging, and delivery.

The difference of 580 rubles between MDF versions may be insignificant compared to veneer, complex painting, or carved base.

You should compare two complete projects: ST-023 plus STL-023 and finishing, or ST-027 plus the selected base and finish.

How not to confuse the price of MDF and veneered versions

The price of 7,120 rubles refers to the MDF version of ST-027 as of the verification date. It cannot be automatically applied to versions with beech or oak veneer.

In the product card, you select a specific material and only then record the cost. The same rule applies to manufacturing conditions and availability.

In the article, the price is used as a comparative reference for basic MDF versions.

How to choose a countertop for repairing an existing table

When replacing an old top, it is important to measure the mounting area, hole locations, and the actual stability of the base.

ST-023 can dramatically increase visual thickness and final height. ST-027 can change the style due to its shaped edge.

The old mount cannot be transferred automatically. The new tabletop requires a separate check of the material and fixing depth.

What to buy together with the tabletop

The "what to buy together" section is not for mechanical upselling. The underframe, fasteners, and finish determine whether a round blank becomes a stable and visually cohesive table. All items are checked as a set before payment.

How not to confuse a furniture tabletop with a kitchen one

ST-023 and ST-027 should not be promoted as kitchen countertops for sinks, hobs, or rows of cabinets. Their diameter, profile, and connections with underframes belong to freestanding furniture.

The query "buy MDF tabletop" is broad, but the article targets a specific intent: a round furniture tabletop for a compact table, coffee table, or side table.

If a buyer needs a kitchen work surface, these two SKUs should not be recommended solely because of the MDF material.

How not to confuse MDF, veneer, and solid wood

ST-023 is confirmed as an MDF tabletop. ST-027 has an MDF version and combined versions with beech or oak veneer and a solid wood rim. No combined version should be called solid wood without clarification.

Veneer provides a natural wood grain pattern, but the construction remains multi-layered. This affects the product description, choice of finish, and buyer expectations.

Understanding the difference in materials helps with the material MDF, veneer, or solid wood for a furniture tabletop, while the specifications of a specific version are always checked against the product card.

How not to confuse compact models with a 1200 mm tabletop

The diameter of ST-023 and ST-027 is in the range of 660–670 mm. These are compact products. Queries about a round tabletop 120 cm or 1200 mm belong to a different size class.

It cannot be promised that these models will replace a large dining top. The almost twofold difference in diameter means a fundamentally different area and under-table space.

If a different size is needed, you should open the category and look at confirmed options, rather than trying to expand the purpose of the current items.

How not to confuse a smooth edge with a figured one

In the front view, the difference in profiles is sometimes lost, especially if the tabletops are shown from above. ST-023 has a smooth volumetric edge, ST-027 has a profiled classic one.

Before ordering, you need to look at the side view or drawing. The figured profile affects light and shadow, finish, and the available mounting area.

If the buyer needs a minimalist circle, ST-027 may be too decorative. If a classic relief is needed, ST-023 cannot replace it with just one color.

Mistakes when buying ST-023

Calling it a solid wood tabletop

The current information indicates MDF. The mistake creates false expectations about wood texture and transparent finish.

Choosing for the sake of an extra ten millimeters in diameter

The area is about 3.1% larger, so the real reason for the purchase is the 65 mm edge, not the work surface.

Do not consider the final height

The thick countertop adds 35 mm compared to ST-027 and can noticeably change the fit and proportions of the finished table.

Consider thickness as a guarantee of load capacity

Load-bearing capacity depends on the fastening and underframe. External massiveness does not replace calculation.

Paint before trial assembly

It is better to check fastening zones and fit before full finishing to avoid damaging the enamel during adjustments.

Mistakes when purchasing ST-027

Consider all versions as solid wood

MDF and combined versions with veneer are confirmed. The material of the selected version should be read in the product card.

Choose only because of a thinner edge

The shaped profile gives a classic character. In a minimalist project, it may be unnecessary.

Ordering veneer without a sample

The wood species name does not guarantee the shade will match the underframe or existing furniture.

Assuming STL-027 is automatically compatible without checking

The related product needs to be checked for mounting, overhang, and the current installation diagram.

Use as a large dining tabletop

A diameter of 660 mm is a compact furniture format and should not be promoted for 1200 mm requests.

Common mistakes when choosing a round MDF tabletop

The most common mistake is looking only from above. Circles with diameters of 660 and 670 mm are almost identical, so a top-down photo hides the main difference. You need to compare the side profile.

The second mistake is buying the tabletop before the underframe or vice versa without having a drawing. This leads to issues with overhang, mounting, height, and stability.

The third mistake is to consider the price of the finished blank as the full cost of the table. The budget includes the base, finish, fasteners, assembly, and delivery.

Who ST-023 is really for

ST-023 is suitable for a buyer who needs a compact round MDF tabletop with a very thick smooth edge. It is especially appropriate in a painted project where natural wood grain is not required.

The model should be considered for pairing with STL-023, for a minimalist table, and for an interior where a massive circle should balance open supports.

ST-023 may not be suitable if a shaped profile, clear finish, natural veneer, or the lightest possible silhouette next to a sofa is important.

Who ST-027 is really for

ST-027 is suitable for a coffee or side table, a carved underframe, and a classic composition. The 30 mm thickness makes the edge lighter and the profile more decorative.

The MDF version is suitable for enamel. Combined options with beech or oak veneer are chosen when the surface should retain a natural pattern.

ST-027 may not be suitable if the buyer needs a deliberately thick smooth disc 65 mm thick or the most minimalist geometry without profiling.

When it is better to choose a different tabletop

Both models have a compact diameter of about 660–670 mm. If a large dining table, oval shape, square top, or different thickness is needed, it is better to go to the tabletops category.

Don't choose ST-023 just because it's thicker, or ST-027 just because of the veneer. First, determine the task, the underframe, and the room size.

On the page where you can Buy a tabletop for a table, it's worth comparing other confirmed models and not limiting the project to two SKUs.

How to store the countertop before finishing and assembly

Store a round countertop on a flat, stable surface, protecting the edge and face from impacts. The figured profile ST-027 is especially important not to place on a hard edge without a pad.

Protect MDF from construction moisture, dirt, and accidental wetting. Do not drill holes for fasteners until the installation diagram is approved.

Before finishing, the product must undergo agreed preparation in a workshop setting. Clarify the specific storage and acclimatization mode with the manufacturer and finisher.

How to accept ST-023 or ST-027 after delivery

Upon receipt, verify the SKU, diameter, thickness, material, and selected version. ST-023 must be confirmed as MDF, ST-027 as a specific MDF or veneered version.

Check the surface, circumference, edge profile, and absence of damage. Record any issues before painting, drilling, and installation.

Current Payment and delivery terms for countertops Checked before placing an order, especially if the product is handed over to a finishing workshop.

How to prepare the countertop for a trial assembly

Before final finishing, the countertop is placed on a soft, clean surface and aligned with the base. Check the center, overhang, access to fastening areas, and overall silhouette.

A trial assembly helps to see if the 65 mm end conflicts with the base and if there is enough space for mounting ST-027 next to the shaped profile.

Markings are recorded on the drawing, not just with pencil marks on the part. This reduces the risk of errors after painting.

How to care for the finished countertop

Care depends on the finish coating. Different restrictions on cleaning agents and methods may apply for enamel and clear varnish.

Liquid is not left on the surface, especially in the area of a damaged end or mounting hole. Abrasive compounds are not used without confirmation of compatibility.

Keep data about the paint, varnish, and tone. They will help with local repairs if the surface is damaged.

How to buy ST-023 or ST-027 on STAVROS

For a smooth, voluminous top, you can buy a round MDF tabletop ST-023 measuring 670 × 670 × 65 mm. In the product card, before ordering, check the material, price, and delivery terms.

For a shaped edge and veneer options, you can buy a shaped round tabletop ST-027 measuring 660 × 660 × 30 mm, choosing the desired finish.

If no profile fits, it is wiser to View all tabletop sizes and choose a different model rather than try to use ST-023 or ST-027 outside their intended purpose.

Pre-order checklist

Why a template is needed not only for the circle but also for the end face

A paper circle with a diameter of 660 or 670 mm shows the location on the floor but does not reveal the thickness. For an honest comparison, a side rectangle with a height of 30 or 65 mm at the assumed countertop level is needed.

From the sofa level, the end occupies a significant part of the field of view. ST-023 may look twice as massive, although from above it almost matches ST-027.

Such a template helps make a decision before purchasing, color selection, and manufacturing the underframe.

How to read a countertop photo in the product card

The photo may be taken from above, at an angle, or on a neutral background, so the actual scale of the edge is difficult to assess.

You need to compare the image with the numerical size and drawing. For ST-023, the key figure is 65 mm, for ST-027 — 30 mm and the profile shape.

The material also cannot be determined from a photo: painted MDF and veneered surface require verification of the selected configuration.

How to choose a countertop for painting according to RAL

ST-023 made of MDF is suitable for a project where the color is selected from a palette and must match the underframe or other furniture.

ST-027 made of MDF can also be considered for opaque finishing, but the shaped profile creates more shadows and visually changes the shade on the edges.

The color number does not replace a test sample. Gloss level, primer, and lighting affect the final result more than the screen sample.

How to choose the direction of the ST-027 veneer pattern

On a round surface, the pattern direction becomes part of the composition. It should be coordinated with the base, adjacent furniture, and the viewpoint.

The article does not assign a specific veneer layout because it depends on the product execution. Before ordering, the customer clarifies the available option in the product card or with a manager.

For paired tables, it is better to coordinate the direction and shade simultaneously.

One table or a paired composition

Two identical tables next to a sofa require the same height, profile, material, and finish. A slight color difference on a pair is more noticeable than on a single item.

ST-023 in a pair creates a strong rhythm of thick round discs. ST-027 looks lighter and allows repeating the figured profile without excessive mass.

It is better to order paired tabletops and bases in one batch and check them together before finishing.

How to choose a tabletop for a showroom or salon

In the showroom, the table is often examined from all sides, so the end and bottom surfaces are especially important. ST-023 demonstrates thickness and color, ST-027 shows profile and texture.

Frequent cleaning, moving objects, and possible local repair of the coating must be anticipated.

For a demonstration interior, the choice is made not only by the picture, but also by which material properties need to be shown to the visitor.

What to check with the manager before payment

You need to confirm the material of the selected version, the current price, configuration, available finish, and delivery terms.

For ST-027, it is separately specified whether MDF, beech veneer, or oak veneer is selected. For ST-023, MDF and the absence of unconfirmed solid wood are fixed.

If a base is ordered, compatibility, attachment points, and the recommended finishing order are checked in one request.

Why a ready-made set is more profitable than a random combination

A tabletop and base selected from a related line are easier to coordinate in scale and style. This does not cancel technical verification, but reduces the risk of a random choice.

A random base may have an unsuitable mounting platform, height, or support footprint. Then saving on one part leads to reworking the entire table.

The STAVROS commercial route is built from the countertop card to the associated under-table, materials, and assembly check.

FAQ: ST-023 or ST-027

1. How is ST-023 different from ST-027?

ST-023 has a diameter of 670 mm, thickness of 65 mm, and a smooth edge. ST-027 has a diameter of 660 mm, thickness of 30 mm, and a shaped profile.

2. Which countertop has a larger area?

ST-023, but the difference is about 3.1%, so the practical area is almost the same.

3. Which model is thicker?

ST-023 is 35 mm thicker and approximately 2.17 times thicker.

4. Does greater thickness mean greater load capacity?

No. Without testing the entire structure, such a relationship cannot be confirmed.

5. What is ST-023 made of?

Made of MDF. It cannot be called a solid wood, beech, or oak tabletop.

6. What materials are available for ST-027?

There is an MDF version and combined options with a solid wood edge and beech or oak veneer.

7. What to choose for enamel?

Both MDF versions. The choice is made between a smooth edge of 65 mm or a shaped profile of 30 mm.

8. What to choose for clear lacquer?

The corresponding veneered version of ST-027 after checking the card.

9. Which model is compatible with STL-023?

ST-023 is directly linked to the three-leg base STL-023.

10. Which model fits STL-027?

ST-027 is shown together with STL-027, but mounting compatibility and overhang are checked.

11. What is the arithmetic height of ST-023 on STL-023?

725 + 65 = 790 mm excluding seating, fastening, thrust bearings and other components.

12. What overhang should be left?

There is no universal value. It is calculated based on the specific table base plan and stability is checked.

13. Which model is better for a coffee table?

Most often ST-027 due to its 30 mm thickness, shaped profile and associated carved base.

14. Which model looks more massive?

ST-023 due to its smooth edge with a thickness of 65 mm.

15. Which model is best for a modern interior?

Usually ST-023, but the choice depends on the base, color, and surrounding furniture.

16. Which model is best for a classic interior?

Usually ST-027 due to its shaped profile and veneer options.

17. Can they be used as a kitchen countertop?

The article considers them as furniture round tabletops, not as a surface for a sink or hob.

18. Can ST-023 be placed on any base?

No. You need to check dimensions, overhang, mounting points, stability, and final height.

19. Can ST-027 be placed on any carved base?

No. A related style does not mean universal mounting compatibility.

20. What was the price at the time of verification?

On July 21, 2026, ST-023 made of MDF cost 6,540 ₽, ST-027 made of MDF cost 7,120 ₽. Prices need to be rechecked.

21. Why is ST-027 only 580 rubles more expensive?

The price depends on the profile and finish, but the current difference only applies to the compared MDF versions as of the verification date.

22. How to protect the MDF end?

Use an agreed-upon system of preparation and finishing, including ends, bottom, and mounting holes.

23. Where to buy ST-023?

In the card of the round MDF tabletop ST-023 on the STAVROS website.

24. Where to buy ST-027?

In the card of the shaped round tabletop ST-027 on the STAVROS website.

How to compare the finishing cost of two models

The blank price does not reflect the cost of the finished surface. The ST-023 has a large smooth side plane 65 mm high, while the ST-027 has a thinner but shaped profile that requires careful edge preparation.

A finishing estimate is requested separately for MDF under enamel and for the veneered version. It cannot be stated in advance that a smooth model is always cheaper to work with or that a shaped one is necessarily more expensive: the result depends on the chosen technology.

It is useful to obtain two complete estimates — tabletop, preparation, finish, and underframe — and only then compare the total cost of the projects.

What data to save after ordering

After selection, save the article number, material type, size, chosen finish, color code, gloss level, and mounting scheme. This information will be useful for reordering or repairs.

For the ST-027, additionally record the veneer species and features of the chosen combined version. For the ST-023, confirm the MDF material and the agreed enamel system.

It is better to store documents together with the underframe drawing. Then future replacement of fasteners or restoration of the coating does not start with re-determining all parameters.

When a manager consultation is needed before payment

Consultation is especially needed if the buyer chooses the veneered ST-027, orders a tabletop together with an underframe, or plans a non-standard finish.

In one request, you should confirm the material, current price, related base, available configuration, and the procedure for transferring the product to the finishing workshop.

The more precisely the task is formulated, the lower the risk of receiving a part that is beautiful but unsuitable in height, profile, or fastening.

Final project check before launching into production

Before painting and final fastening, the tabletop, underframe, and mounting diagram are checked as one set.

At this stage, the center, overhang, final height, access to fasteners, and absence of profile conflict with the base are confirmed.

Only after such a check does it make sense to start the final finishing and assemble the finished table.

Result: thick ST-023 or shaped ST-027

ST-023 and ST-027 are almost identical in diameter and usable area, but completely differ in side silhouette. ST-023, size 670 × 670 × 65 mm, is a smooth MDF tabletop for custom opaque finishing. ST-027, size 660 × 660 × 30 mm, is a thinner shaped model available in MDF and in combined versions with beech or oak veneer.

ST-023 is chosen for the 65 mm thick edge, laconic geometry, and pairing with the three-legged STL-023. ST-027 is chosen for the shaped profile, coffee or side table format, carved STL-027, and the ability to preserve the natural texture of the veneer. The price difference between the MDF versions at the time of verification was 580 rubles, so savings should not replace the correct choice.

Before ordering, check the material of the specific version, underframe, overhang, fastening, final height, and finish. On the STAVROS website, you can view price ST-023, view price ST-027 or select tabletop for base from other confirmed models.