Buy wooden furniture legs: faceted MN-214 160 mm or turned MN-222 120–180 mm — which to choose

Wooden furniture legs are bought not only for decorative renewal. The height and shape of the supports determine the final level of the sofa, bedside table, or dresser, the clearance above the floor, ease of cleaning, and how heavy or light the body appears. Therefore, comparing faceted furniture leg MN-214 и turned furniture leg MN-222 needs to be like two different systems: with their own heights, cross-sections, fasteners, and kit budget.

MN-214 has a fixed height of 160 mm and dimensions of 160 × 44 × 60 mm. Its strict faceted shape is noticeable in the interior and supports the modern geometry of furniture. The card indicates beech or oak, "Prestige" sanding, and the main fasteners included: metric stud screw M8 × 60, metal insert nut M8, and universal screw. This is important because the buyer receives not only a wooden support but also a pre-defined mounting configuration.

MN-222 is designed differently. It is a compact turned leg with a square cross-section of 45 × 45 mm, available in heights of 120 or 180 mm. Beech and oak are also available, and the sanding is specified as "Prestige". The price of one piece is noticeably lower than MN-214, but the FUR-001 and FUR-012 fastening options, as well as the round foot cap FUR-021, are selected separately. Therefore, the final project cost consists of more than just four wooden parts.

Below, three heights are compared — 120, 160, and 180 mm, geometric and turned shapes, fastener completeness, beech and oak, cost of one and four legs, application on a sofa, cabinet, and chest of drawers, base inspection, and installation errors. Prices and availability reflect the data from the cards at the time of preparing the diagram; they must be rechecked before ordering.

Carved Furniture Leg MN-002

from 107.84 $

Carved Furniture Leg MN-018

from 31.23 $

Precision Furniture Leg MN-233

from 29.03 $

Furniture leg set KON-008

from 108.82 $

Furniture leg set KON-009

from 111.25 $

Furniture leg set KON-010

from 139.92 $

Furniture leg set KON-011

from 183.72 $

Go to Catalog

MN-214 or MN-222: short answer

Watch video ...

When to choose MN-214

MN-214 is worth buying when the 160 mm height already suits the project, the leg should be a visible part of the design, and the strict faceted surface better supports straight fronts, geometric handles, and laconic bodies. It is especially convincing on a cabinet or chest of drawers, where there is a noticeable gap between the floor and the bottom plane, and the support does not hide deep under the body. The included fasteners reduce the number of separate items but do not eliminate the need to check the strength of the bottom frame.

Our factory also produces:

Turned leg with decoration MN-145.1

from 10.98 $

Turned Furniture Leg MN-178

from 30.25 $

Precision Furniture Leg MN-179

from 33.43 $

Precision Furniture Leg MN-183

from 29.64 $

Geometric Furniture Leg MN-205

from 56.97 $

Geometric Furniture Leg MN-206

from 35.01 $

Geometric furniture leg MN-214

from 18.05 $

Modern Furniture Leg MN-228

from 14.76 $

View Full Product Catalog

When to choose MN-222 with a height of 120 mm

MN-222 with dimensions of 120 × 45 × 45 mm is suitable for furniture that cannot be raised too high. This option helps maintain a comfortable sofa seat height, not raise a bedside table too high relative to the mattress, and not make a small chest of drawers disproportionately elongated. This is the most affordable configuration among those compared, but the price must include the selected fasteners and, if necessary, foot caps.

When to choose MN-222 with a height of 180 mm

A height of 180 mm is needed when the body should look lighter, a larger clearance is required under the furniture, or the calculated countertop mark is higher than what MN-214 provides. The difference from 160 mm is only 20 mm, but on a finished sofa or cabinet, these millimeters add to the thickness of the body, soft filling, countertop, and mounting assembly. Therefore, the choice is made based on the total height, not on an individual leg.

Why this comparison is not about style

In the photo, MN-214 and MN-222 differ primarily in pattern. The first looks like a modern faceted support, the second like a calm turned part. But the decorative character is only one of five parameters. When switching from 120 to 160 mm, the body rises by 40 mm; when switching from 160 to 180 mm, by another 20 mm. At the same time, the clearance, handle position, relationship with adjacent furniture, and seating comfort on the sofa change.

The second parameter is the mounting cross-section. MN-214 has dimensions of 44 × 60 mm, so its upper part occupies a rectangular area. MN-222 is built on a square of 45 × 45 mm. These numbers are important for marking, edge clearance, and checking whether the mounting hole falls into a thin or weakened area of the bottom. The same wood species does not make the models interchangeable.

The third parameter is completeness. For MN-214, the main fasteners are indicated in the kit. For MN-222, the card offers several separate solutions, meaning before purchasing, you need to decide which assembly corresponds to the specific body. The most affordable leg may require additional items and time for selection. The most expensive one does not automatically become more reliable: the result depends on the base and proper installation.

The fourth and fifth parameters are the material with finish and the overall budget. Beech is usually chosen for opaque enamel, oak when you want to preserve and emphasize the texture with tinting or a transparent coating. With four legs, the price difference is multiplied by four, and with a long body, a separate engineering solution for the central support may be needed. First, calculate the furniture, then select the article.

Comparison table of MN-214 and MN-222

MN-214: what the buyer gets for a higher price

Buy geometric furniture leg MN-214 it makes sense not for the sake of the higher price itself, but for a specific set of properties. The height of 160 mm occupies an intermediate position between the two MN-222 options. The rectangular cross-section of 44 × 60 mm and faceted processing make the leg visually wider from one angle and thinner from another. On furniture, this creates controlled geometry: the supports can align with the verticals of the facade or be rotated to emphasize the depth of the body.

The card links MN-214 to cabinets, sofas, and chests of drawers. This does not mean that four legs can be screwed to any product without calculation. For a sofa, the load-bearing frame is important; for a chest of drawers, the condition of the bottom panel and the location of partitions; for a cabinet, the distances from the edge and doors. The complete fasteners determine the intended joint, but the entire body, together with the installation location, bears the load.

In the beech version, MN-214 is specified with preparation for enamel, in oak — for tinting. Faceted surfaces are especially sensitive to the uniformity of the finish: uneven enamel thickness, unpainted edges, or different gloss levels will be noticeable in side light. When tinting oak, the facets emphasize the direction of the grain, so four legs are best evaluated as a set and coordinated by overall color.

The main advantage of the configuration is the presence of basic fasteners in the card: M8 × 60 self-tapping stud, M8 metal bushing, and universal screw. This allows you to discuss the specific diameter and depth of the assembly in advance. However, thin chipboard, hollow construction, or a weakened edge may still require reinforcement or a different scheme designed by the master.

MN-222: why a turned leg remains a strong choice

Buy turned furniture leg MN-222 it is reasonable when the project prioritizes height and a calm profile over a noticeable faceted shape. The square section of 45 × 45 mm simplifies visual perception from above, and the turned silhouette makes the support more neutral. It does not require handles and facades to necessarily repeat complex geometry, making it suitable for updating various furniture.

Two sizes solve different tasks. The 120 mm leg leaves a moderate gap and interferes less with the original height of the body. The 180 mm model noticeably separates the furniture from the floor and helps achieve a taller composition. The buyer can choose extreme options around the height of MN-214, but should not consider 160 mm as a simple arithmetic mean: the shape and fasteners remain different.

MN-222 is significantly more affordable per single part. The price in beech is 430 ₽ for 120 mm and 660 ₽ for 180 mm; in oak — 610 and 930 ₽. This difference makes the model attractive for sets of four, six, or more supports. However, the quantity cannot be increased arbitrarily: the support points must work together with the frame, and uneven floors or slight height differences can cause wobbling.

The card offers separate hardware: FUR-001, FUR-012, and round base pad FUR-021. This is not a drawback as such. Separate selection allows adapting the assembly to the body, but requires more careful specification. An order of "four MN-222" without a fastening solution remains incomplete.

How heights 120, 160, and 180 mm change finished furniture

Difference between 120 and 160 mm

MN-214 raises the body by 40 mm higher than MN-222 with a height of 120 mm. For a bedside table, this may bring the tabletop above the mattress; for a sofa, it may change the seating height; for a chest of drawers, it may raise the handles and top surface. On the other hand, the additional gap makes it easier to access under the furniture and makes a massive body visually less heavy.

Forty millimeters are rarely perceived as a small detail after assembly. If a 500 mm high cabinet is placed on 120 mm legs, the nominal height without the countertop and fastening will be 620 mm. With MN-214, it will be 660 mm. This is already a different level relative to the bed, windowsill, or adjacent console.

The difference between 160 and 180 mm

MN-222, 180 mm high, adds only 20 mm to MN-214. On the drawing, the difference seems small, but in the interior, it affects the gap to the baseboard, the passage of the vacuum cleaner nozzle, the alignment of the cabinet with the mattress level, and the seat position. If the furniture is already calculated close to the limit of comfortable height, twenty millimeters can be decisive.

A high leg does not automatically make furniture lighter or more comfortable. The higher the cabinet is from the floor, the more noticeable the support and the more important the stability of the entire structure. Load capacity cannot be derived from the height or thickness of the leg. Data on the cabinet, fastening method, and load distribution are needed.

Why you cannot choose only based on the robot vacuum cleaner

The clearance under furniture is indeed related to cleaning, but the leg height is not equal to the clear passage. The bottom frame, apron, soft upholstery, decorative plinth, or sagging element may be located below the attachment point. First, measure the minimum height over the entire area, then compare it with the actual dimensions of the equipment.

Formula for the final height of furniture

For a preliminary calculation, a simple sum is used: cabinet height plus leg height plus countertop or soft package thickness plus mounting transition height, if it protrudes beyond the plane. From the result, only those elements that structurally go inside the cabinet are subtracted. The formula helps compare options but does not replace a drawing.

Example for a cabinet: cabinet 420 mm, countertop 20 mm. With MN-222 120 mm, the nominal height is 560 mm. With MN-214 — 600 mm. With MN-222 180 mm — 620 mm. When choosing, you need to compare these marks with the bed height, mattress, and socket placement, rather than looking for a universal number.

The example for a sofa is more complex. To the frame height, add the leg, seat base, filling, and its degree of compression. Therefore, replacing the standard 120 mm with 180 mm and expecting exactly plus 60 mm to comfortable seating is not possible. The frame position and lift angle will change, but the feel depends on the soft package.

When a broader overview is needed, it is helpful to open the material about types and sizes of furniture legs. For the specific pair MN-214/MN-222, the decisive factor remains the furniture's own drawing with three height options.

Faceted or turned shape: what will change in the interior

MN-214 creates clear planes and edges. On a light monochrome body, they provide a calm but noticeable chiaroscuro. On dark furniture, the facet looks stricter, especially next to a rectangular handle or a panel-less facade. This leg works better when it is not hidden too deep under the body and at least two planes are visible.

MN-222 is perceived as softer. The turned profile suits furniture where the support should maintain the overall silhouette but not become the main decorative object. It is appropriate both in calm classics and in a neutral modern composition, especially under enamel in the body color. The 180 mm option is more noticeable, so its rhythm still needs to be evaluated at the scale of the entire furniture.

Style cannot be chosen in isolation from quantity. Four prominent faceted legs form a distinct frame at the bottom of the furniture. Six or eight repetitions strengthen the geometry even more. Turned supports are usually perceived as calmer in large numbers, but their profile also creates a repeating pattern.

To assess proportions, you can look at ideas for dressers and cabinets on wooden legs, and then return to the actual dimensions of the body. An interior photo helps choose the character but does not determine the height and attachment.

Section 44 × 60 or 45 × 45 mm: why it matters

The top platform MN-214 is rectangular. If you turn the leg with the wide side along the facade, it will be perceived differently than when turned in depth. The orientation of the four parts is set before drilling, otherwise the edges may face different directions. For MN-222, the 45 × 45 mm square removes the question of rectangular rotation, but the turned pattern is still checked along the visual axis.

The mounting platform must fully rest on a solid part of the body or reinforcements. The stud cannot be placed too close to the edge, joint, confirmat hole, or void. The size 44 × 60 mm does not mean that any panel of that area will support the assembly. The material and thickness of the base are more important than the simple area.

When replacing old legs, not only the outer contour is compared, but also the position of the mounting center. The new support may only partially cover the old hole, and re-drilling next to it will weaken the material. Sometimes it is more rational to install a reinforcing platform or shift the entire assembly according to an agreed scheme.

A detailed route for updating furniture describes material about how to replace legs on a dresser, nightstand, or sofa. In a new project, it is better to provide platforms in advance than to adapt the body after finishing.

Price of one leg and a set of four

The table shows the cost of wooden legs only at the prices indicated in the diagram. For MN-222, you need to add fasteners and glides in the selected quantity. For MN-214, the main fasteners are already included in the product card kit, but additional materials, reinforcements, and final finishing are also calculated separately.

Comparison is especially important for a long cabinet. Four legs is a common but not universal scheme. The number of supports and the need for a central point are determined by the design, span, weight of contents, and partition placement. You cannot multiply the price by five until it is confirmed that the fifth leg is indeed specified in the project.

It is useful to keep the budget in two columns: "product" and "finished assembly". The first includes legs, fasteners, and glides. The second includes cabinet reinforcement, preparation, painting, labor, and possible floor adjustment. This way, the more expensive MN-214 does not seem unreasonably expensive just because of the price, and the affordable MN-222 is not perceived as a fully ready kit without hardware.

Why the most affordable leg does not always give the most affordable project

The MN-222 120 mm has the lowest price among the compared options. But the savings only hold when the cabinet already suits the chosen fastening, does not require complex reinforcement, and the 120 mm height matches the task. If you have to redo the base or change the legs to 180 mm after purchase, the initial difference becomes meaningless.

MN-214 is more expensive, but its card immediately describes the main fasteners. This simplifies the specification and allows you to check the compatibility of the M8 stud and threaded insert with the base at an early stage. With proper preparation, the buyer reduces the risk of forgetting an important item. With improper preparation, the included fasteners do not save you from a weak panel.

The finish also affects the estimate. The faceted surface of MN-214 requires careful work on the edges, and the four visible supports must look identical. The turned MN-222 have a different relief and may require more careful coating application in profile transitions. You cannot consider one model inherently cheaper to finish without the project's technology.

A rational choice is one that covers height, appearance, and installation without subsequent rework. The price of four parts remains important, but it is evaluated after checking the cabinet.

Fastener MN-214: what's included and what to check anyway

The MN-214 card diagram shows a metric self-tapping stud M8 × 60, a metal insert M8, and a universal screw. This set indicates the intended principle of a detachable connection: a metal threaded element connects the wooden leg and the prepared base. This is more convenient than a random self-tapping screw, but requires a precise axis and suitable material thickness.

Before installation, check the length of threaded parts, seating depth, drilling diameter, and absence of intersection with body fasteners. The insert must work in a strong material, not in a loose edge. For a sofa, the joint is usually connected to the frame; for a chest of drawers or bedside table, an embedded or reinforcing plate may be needed.

The kit cannot be interpreted as confirmation of universal load capacity. The card describes the composition, but the stability of the finished furniture depends on the body geometry, number of points, distance between them, and assembly quality. If in doubt, the joint should be checked by a furniture maker or designer.

A dry fit before painting allows you to ensure that the leg fits without distortion, the thread enters along the axis, and the edges of all four supports are oriented identically. Only after this is the final finishing and assembly performed.

Hardware for MN-222: FUR-001, FUR-012 and foot pad FUR-021

For MN-222, the card suggests buying the FUR-001 kit for attaching legs и selecting the mounting kit FUR-012. The presence of two options does not mean you can choose any based on price or appearance. You need to compare the kit diagram with the body material, access to the installation site, and the ability to form a strong mounting platform.

Round FUR-021 glider with a diameter of 19 mm It is considered as a separate accompanying item. It helps organize the contact of the leg with the floor and protect the lower part from direct friction, but does not correct serious curvature and does not replace the adjustable support. The number of gliders should correspond to the number of legs.

In the MN-222 specification, the size of 120 or 180 mm, wood species, quantity, selected mounting kit, and gliders must be indicated in separate lines. The phrase "four MN-222" is too vague: different node options may require different body preparation.

Before ordering, it is useful to show the diagram of the lower part of the furniture to the manager or craftsman. This allows you to select the hardware before drilling, rather than adapting it to already existing holes. If the body is assembled by a third-party workshop, it is better to coordinate the list of components with them before payment.

What to buy together with furniture legs

The "buy together" section should not turn into an automatic upsell list. For MN-214, the main fasteners are already included in the card, so there is no need to add a random set again. For MN-222, the choice of fittings is mandatory, but the specific option depends on the design. A footrest is only useful when it matches the bottom geometry and floor.

If the choice is not yet limited to two models, you can Buy wooden furniture legs in the main catalog and compare other heights and shapes. For a project for self-painting, it is convenient choose unpainted legs made of beech or oak.

How to choose legs for a sofa

For a sofa, first determine the required seat height and the design of the supporting frame. The leg is attached not to the soft upholstery or to a random thin panel, but to a prepared unit. MN-214 with a height of 160 mm is suitable when the geometric support should be noticeable and the calculated seat mark allows such a lift.

MN-222 120 mm is rational for a tall body or thick soft package. The 180 mm option increases clearance but may make the seat higher. The difference is evaluated on a mockup or based on the actual dimensions of the old sofa. Comfort cannot be derived from leg height without considering the filling.

To filter models by purpose, you can buy wooden sofa legs in the thematic section. After choosing the shape, you need to check the attachment to the frame, the number of points, and the offset from the corners. A long sofa may require additional supports, but their number is determined by the manufacturer or designer.

If replacing old legs, measure not only their height but also the thread depth, distance to the edge, and the condition of the frame. A direct increase from 120 to 180 mm may increase leverage on the joint, so the base must be designed for the new configuration.

How to choose legs for a bedside table

For a bedside table, the main reference is the level of the tabletop relative to the mattress and the ease of access to the drawers. A body height of 420 mm with a 20 mm tabletop on MN-222 120 mm will give about 560 mm. On MN-214 — about 600 mm, on MN-222 180 mm — about 620 mm. These figures are compared with a specific bed.

MN-214 works well on a laconic body with straight fronts and a geometric handle. MN-222 is suitable when the legs should be calmer or the table has a classic profile. With a small width, overly active supports can visually compete with the front.

The attachment point is especially important: on a narrow table, the leg ends up close to the side panel and drawer slides. Drilling is planned so as not to damage the hardware or weaken the body joint. The glides must be in the same plane, otherwise light furniture will wobble.

It is useful to study in advance how to choose wooden supports for a dresser and table, and then compare two specific cards by height and completeness.

How to choose legs for a dresser and TV cabinet

A dresser creates a longer span and often stores heavy items. Four corner supports may be insufficient for a specific design, but a universal number cannot be given. The bottom frame, central partitions, and deflection are evaluated. If the project includes a fifth or sixth support, its height and attachment must match the others.

MN-214 makes the lower part of the dresser expressive and suits facades with a clear grid. MN-222 120 mm keeps the body closer to the floor and reduces visual gap. MN-222 180 mm creates a higher clearance but increases requirements for stability and precision of all points.

For a TV cabinet, additionally consider cables, ventilation, and screen position. Increasing the height by 20–60 mm changes the TV level. If the screen is already mounted on the wall, the new cabinet must align with the existing composition.

Before drilling, you can refer to the material about how to install wooden legs on a dresser. But the sequence of actions is adapted to the chosen fasteners and body material.

Is a fifth central support needed

A fifth leg is not a mandatory accessory for any dresser or sofa. It is only needed when the design includes a central point and transfers load to it. Installing a random support under a thin panel may not strengthen the body but create local stress and leave the corner legs partially unloaded.

If the central partition reaches the bottom frame, the designer can connect an additional leg specifically to it. For a long span without a partition, reinforcement is created first. The height of the central support must exactly match the corner ones, otherwise the furniture will rest unevenly and start wobbling even on a level floor.

For MN-222, an additional position means separate fasteners and a base plate. For MN-214, it means another set of the product with specified hardware. The budget is calculated after the design decision. The price should not push towards refusing a necessary support or, conversely, buying an unnecessary part.

In the absence of a drawing, it is wiser to consult a furniture maker. The article helps formulate questions and compare products, but does not replace the calculation of body strength, span, and support points.

Beech or oak for MN-214 and MN-222

Both models are available in beech and oak. A detailed explanation of wood preparation includes a section on how STAVROS prepares beech and oak. For the buyer, the practical choice primarily concerns the finish and how noticeable the natural texture should be.

Beech for enamel

Beech is often chosen for opaque enamel. The uniform surface helps achieve an even color, and the leg shape is read through light and shadow. On MN-214, the enamel emphasizes the edges; on MN-222, the smooth transitions of the turned profile. It is better to paint all parts of the set with the same system and under identical conditions.

If the legs are painted to match the body color, a test application is done on the same wood species and preparation. Matching the paint code does not guarantee the same shade on different substrates. Primer, layer thickness, and gloss significantly affect the result.

Oak for tinting

Oak is chosen when the wood grain is to be preserved. Tinting changes the color but should not completely hide the texture. On the flat planes of MN-214, the direction of the fibers becomes part of the geometry. On MN-222, the texture runs along the rounded transitions and appears softer.

You cannot choose the wood species based solely on price. If the body is already made of oak or veneer with a pronounced texture, a beech leg with a clear finish may look out of place. If the entire piece will be painted with a dense enamel, the expensive oak texture may not provide the expected visual benefit.

What does "Prestige" sanding mean?

The product cards for both models indicate "Prestige" sanding. This is a characteristic of the wooden surface preparation, not a promise of ready-made enamel, oil, or varnish. After receiving the product, check what additional primer and interlayer treatment are needed for the chosen coating system.

Faceted edges MN-214 cannot be

Check the bottom panel and frame

First, determine which part of the body is truly load-bearing. A thin decorative panel, drawer bottom, or upholstery plywood should not automatically become the attachment point. Look for a frame, stile, insert, or partition through which the load is transferred to the entire body.

If there is no suitable platform, design it before finishing. The reinforcement must connect to the body, not just cover a weak panel from above. The material, thickness, and area are determined by the craftsman based on the furniture.

Make markings from a single base

Four points are measured from the common lines of the body, not from random edges. For MN-214, additionally set the orientation of the rectangular cross-section. Check the markings with diagonals and a template. An error of a few millimeters can be noticeable on the facade and cause misalignment.

For MN-222, it is important not to confuse the heights if parts of different sizes are present on the site. Mark each leg before installation. Mixing 120 and 180 mm in one horizontal body is not allowed unless specifically intended by an unusual design.

Conduct a dry fit

Before finishing, temporarily install the legs, place the furniture on a level surface, and check fit, orientation, height, and absence of wobbling. Such a dry fit reveals mismatched fasteners, base issues, and the need for reinforcement.

Also check door and drawer opening, distance to the baseboard, visibility of legs from main angles, and clearance for cleaning equipment. After painting, changing axes is significantly more difficult.

How not to confuse MN-214 and MN-222 with similar products

The first sign of MN-214 is a fixed height of 160 mm and a rectangular dimension of 44 × 60 mm. If the card indicates 120 or 180 mm and a square of 45 × 45 mm, it refers to MN-222. The name "unpainted furniture leg" is not enough: the article number and full size are recorded in the specification.

The second sign is the shape. MN-214 is faceted and geometric, MN-222 is turned. On a small preview, the difference may not be obvious, so open the drawing and photos from several angles. A display or sample helps to assess the real light and shadow, but the dimensions are still checked against the card.

The third sign is the fastening. For MN-214, the main set is indicated in the kit. For MN-222, the diagram lists separate FUR-001, FUR-012, and FUR-021. If the order contains only wooden items, the mounting kit for MN-222 is likely incomplete.

The fourth sign is the height. You cannot order a "medium MN-222" because the diagram includes 120 and 180 mm. You cannot order a "taller MN-214" without switching to another model: its confirmed height is fixed at 160 mm. Colloquial descriptions are always replaced with the exact article number and dimension.

Practical selection for different tasks

The table provides direction but does not replace measurement. For example, MN-222 120 mm may be too high for a cabinet with an unusually tall body, while MN-214 may be suitable for a small chest if its proportions are designed for 160 mm. The scenario is always verified with numbers.

If in doubt, it is useful to cut out a side contour of the leg from cardboard at a 1:1 scale and attach it to a photo of the body. Such a mockup shows the visual scale but does not check the fastening. For installation, a drawing of the lower part is still needed.

Common mistakes when buying MN-214

The first mistake is choosing MN-214 only because the fasteners are included. The completeness is convenient, but it does not confirm compatibility with any body. If the base is too thin or the hole falls into a weak zone, a different assembly design is needed.

The second is ignoring the rectangular cross-section. The four legs may be rotated differently, and the faceted composition will lose order. The orientation is marked on the drawing and during dry fitting.

The third is considering the height of 160 mm universal for a sofa, cabinet, and chest of drawers. The final mark depends on the body. First, calculate the furniture, then choose the leg. It is especially dangerous to replace standard low supports with 160 mm ones without assessing stability.

The fourth is comparing only the price of one part. For four oak MN-214 in the scheme, the total is 7,120 ₽. This amount should be a conscious part of the budget, justified by the shape, height, and completeness.

Main mistakes when buying MN-222

The first mistake is ordering MN-222 without specifying 120 or 180 mm. The 60 mm difference completely changes the furniture height. The size is fixed in each line of the specification and checked on the packaging before installation.

The second is forgetting the fasteners and glides. The low price of the wooden part does not automatically include FUR-001, FUR-012, or FUR-021. The configuration is assembled before payment and checked by quantity.

The third is choosing fasteners based on a photo. The kit must match the base and installation method. Without a drawing of the body, the decision remains incomplete. You cannot simply repeat the scheme of another piece of furniture if it has a different frame.

The fourth is expecting the turned leg to be unnoticeable. At a height of 180 mm, the support forms a distinct rhythm and affects the style. It needs to be evaluated at the scale of the entire furniture, not just on a white background of the product card.

Who MN-214 suits, and who should choose a different option

MN-214 is suitable for a customer who already knows the required height of 160 mm, wants to make the legs a noticeable part of the design, and is willing to pay for the faceted shape. It is appropriate in modern furniture, in projects with straight fronts, and where the included fasteners simplify specification.

The model may not be suitable if the body must remain low, the budget for four or six legs is limited, and the geometric facets conflict with a soft classic silhouette. It is also not automatically suitable for a thin panel without reinforcement.

MN-222 is suitable for those who need a choice of 120 or 180 mm, a calm turned shape, and a more rational cost for a wooden set. The model is convenient for updating furniture if the appropriate fasteners are selected in advance.

MN-222 is not suitable without specifying the size and fittings. It is not a ready-made all-in-one universal set. If the project specifically requires a height of 160 mm, an attempt to compensate for the difference with the body or a foot pad must be justified, not done accidentally.

How to place an order without ambiguities

The specification includes the article number, size, wood species, quantity, finish option, and fasteners. For MN-214: "MN-214, 160 × 44 × 60 mm, beech or oak, quantity, main fasteners per card." For MN-222, be sure to add "120" or "180 mm" and separate fitting items.

Attach a diagram of the lower part of the body with panel thicknesses, partition locations, and distances to the edges. For MN-214, note the 44 × 60 mm orientation. For MN-222, show the central mounting axis and the selected set.

Prices, availability, and delivery times are checked as of the order date. In the original diagram, MN-214 was in stock in Saint Petersburg, and four variants of MN-222 were noted as available, but such data changes and should not be carried over into the publication as a permanent guarantee.

Before payment, it is useful to check payment and delivery terms for furniture legsFor a complex cabinet, you can order a selection of furniture legs for the cabinet and approve the set before production or finishing.

How to buy MN-214 or MN-222 on STAVROS

First, open both product cards and check the full dimensions. For MN-214, verify 160 × 44 × 60 mm and the fastener composition. For MN-222, choose 120 × 45 × 45 or 180 × 45 × 45 mm, then add the approved fittings.

The second step is to calculate not just one leg, but the total quantity. For four supports, multiply the price by four; for a different quantity, multiply by the number confirmed in the project. For MN-222, add fasteners and glides.

The third step is to choose beech or oak along with the finish. Beech is considered for enamel, oak for tinting and preserving the texture. The finish of all parts of one item is approved as a unified system.

The fourth step is to check the cabinet. If you are unsure about the thickness, inserts, or central support, it is better to consult a specialist before drilling. STAVROS provides product selection points and related items, but finished furniture requires a correct structural solution.

How to check the scale with a full-size template

When the numbers 120, 160, and 180 mm are hard to visualize on screen, it is useful to make a paper or cardboard template of the side profile at a 1:1 scale. For MN-214, mark a height of 160 mm and a maximum depth of 60 mm. For MN-222, make two templates with heights of 120 and 180 mm and a width of 45 mm. Apply them to a photo or the actual cabinet.

The template shows how noticeable the leg will be, where the bottom plane of the furniture will end up, and whether the body will visually appear too tall. For a sofa, the mockup is evaluated together with the seat height; for a bedside table, next to the bed; for a chest of drawers, considering the baseboard and adjacent items.

For MN-214, the wide and narrow sides are marked on the template. This helps choose the orientation of the faces. For MN-222, the overall turned silhouette is drawn to understand whether the profile will be lost under a deeply recessed body. The mockup does not confirm fasteners and load, but prevents scale errors.

After visual inspection, return to the drawing. The solution is considered ready only when the height, style, mounting area, hardware, and budget for the entire quantity match.

What to check upon receiving the set

Before painting and installation, verify the article number, height, wood species, quantity, and surface condition. For MN-222, it is especially important to ensure that all parts have the ordered height of 120 or 180 mm. For MN-214, check the uniform orientation of the faces and the presence of fastening elements stated in the card.

Place four legs next to each other on a flat surface and visually compare the height, wood grain, and preparation quality. For oak, evaluate the difference in tone and texture; for beech, the uniformity of the surface under enamel. Natural wood does not have to have an absolutely identical pattern, but the set must be acceptable for the chosen finish.

Hardware for MN-222 is counted separately: the number of sets and glides must match the specification. Do not start drilling until the fastener dimensions and base layout have been checked.

If a discrepancy is found, document it before any irreversible actions. Painting, trimming, or drilling complicates subsequent resolution and may make comparison with the order impossible.

FAQ: answers to questions about MN-214 and MN-222

Which leg is taller — MN-214 or MN-222?

MN-222 is available in two heights. The 120 mm version is 40 mm lower than MN-214, and the 180 mm version is 20 mm higher than MN-214.

Which model is cheaper as a set of four?

According to the price scheme, MN-222 is cheaper in both heights and finishes. However, you need to add the selected fasteners and support pads to it.

Does MN-214 include fasteners?

The card indicates an M8 × 60 self-tapping stud, an M8 metal insert, and a universal screw are included. Compatibility with the body is checked separately.

What fasteners are needed for MN-222?

The scheme offers FUR-001 and FUR-012 as options, and FUR-021 as a round support pad. The specific set is chosen based on the base design.

Which legs to choose for a sofa?

First, calculate the seat height and check the frame. MN-214 is suitable for noticeable geometry and 160 mm; MN-222 is for 120 or 180 mm and a turned profile.

Which legs to choose for a bedside table?

Compare the final height of the countertop with the mattress. For a tall body, 120 mm is often more convenient, but the exact solution depends on the bed.

Can the MN-214 be installed on an MDF chest of drawers?

The body material itself does not provide an answer. The thickness, embedded part, partition layout, and suitable assembly are needed. It cannot be attached to a thin panel without verification.

Is a fifth leg needed under a long chest of drawers?

Only if it is provided by the design. The central support must be connected to the reinforcement and have an exact height.

What is better for enamel — beech or oak?

Beech is usually chosen for opaque enamel. Oak is more often used for tinting and preserving texture.

Can the MN-214 and MN-222 be tinted?

Yes, in the diagram, oak is indicated with preparation for tinting. The specific coating system is agreed upon before installation.

What does "Prestige" mean?

This is a surface sanding option, not a finished topcoat.

Can the MN-222 180 mm be shortened to 160 mm?

Self-trimming is not confirmed and may compromise shape and fit. For 160 mm, consider MN-214 or another suitable model.

Is MN-222 120 mm suitable for a robot vacuum cleaner?

You need to measure the minimum clear opening considering the frame and other elements. The leg height does not equal the actual passage.

How to orient MN-214?

The rectangular section 44 × 60 mm is rotated identically at all points according to the accepted composition. Orientation is set before drilling.

Are foot pads needed for MN-214?

In the original design, a separate foot pad for MN-214 is not specified. The need for floor protection and bottom contact is clarified per the project.

Can legs be attached only with glue?

Such a universal method is not confirmed. Attachment depends on the design and usually requires a calculated mechanical assembly.

Which model looks more modern?

MN-214 has a more pronounced faceted geometry. MN-222 is calmer and more versatile, but the style depends on the body and finish.

Will four legs fit any dresser?

No. The number depends on the length, bottom frame, partitions, and load. Sometimes additional support or a different design is required.

Can I replace old 120mm legs with MN-222 180mm ones?

Only after calculating the new height and checking the attachment. An increase of 60mm changes stability, fit, and appearance.

What to check upon receipt?

Article number, size, wood species, quantity, surface quality, completeness of fasteners, and absence of damage before painting and installation.

Result: faceted MN-214 or turned MN-222

MN-214 and MN-222 solve a similar furniture task but lead to different results. MN-214 offers a fixed height of 160mm, rectangular section 44×60mm, a noticeable faceted shape, and basic fasteners included. MN-222 offers a choice of 120 or 180mm, square 45×45mm, a calm turned profile, and a significantly lower price for the wooden part.

For a cabinet, sofa, and dresser, first calculate the final height and check the base. Then choose the style, wood species, and fasteners. Four legs are not a universal scheme for any body, and the presence of complete fittings does not cancel the structural check.

Beech is suitable for projects with opaque enamel, oak for those where natural texture and tinting are important. 'Prestige' sanding means surface preparation, but not a finished finish. All legs of one set are finished and fitted together.

On the STAVROS website you can compare dimensions and price of MN-214 с dimensions and prices of MN-222, add the necessary fittings and check neighboring models in the catalog. Before ordering, it is necessary to re-check prices, availability, completeness, and delivery times. An informed choice allows you to get not just four beautiful parts, but furniture of the correct height, stable within the calculated structure, and cohesive in style.

Control checklist before final selection

Before purchasing, record the body height, tabletop or soft package thickness, desired final level, minimum clearance, bottom frame material, and number of supports according to the project. Then separately note the style: faceted geometry or turned profile. This order prevents the decorative impression from overriding the technical parameters.

For MN-214, confirm the size 160 × 44 × 60 mm, wood species, quantity, orientation of the wide side, and the possibility of using the M8 kit in the prepared base. For MN-222, confirm either 120 or 180 mm, wood species, quantity, FUR-001 or FUR-012, and the need for FUR-021. All items must be in one specification.

Compare the cost of four wooden legs and the total cost of the assembly. Then evaluate the time and complexity of finishing. If the budget difference is justified by the appearance of MN-214, choose it consciously. If the project is satisfied with the turned shape and one of the MN-222 heights fits without compromise, overpaying for the faceted model is not necessary.

The final check is performed on the mockup and drawing. The body must stand at the selected height, doors and drawers must open, legs must fall into strong zones, and the coating must match the furniture. Only after this does the choice between MN-214 and MN-222 become not a taste assumption, but a ready order.

How to compare three heights on one drawing

Draw the body in a side projection and draw three floor lines: for MN-222 120 mm, MN-214 160 mm, and MN-222 180 mm. On one sheet, you can immediately see how the position of the tabletop, bottom drawer, handles, and free space changes. Such a drawing is more useful than three separate photos because all options are compared from a single base.

For a pedestal, the mattress level is marked; for a sofa, the estimated seat height; for a TV stand, the lower edge of the screen. If one of the lines intersects a socket, baseboard, or other object, the option is excluded before purchase. Then, at the selected height, the actual shape of the leg is drawn to check not only function but also scale.

On drawing MN-214, it is shown as a rectangle of 44 × 60 mm with the selected orientation. MN-222 is indicated by a square of 45 × 45 mm. This helps evaluate the gaps from the side panels and facade, and also understand in advance whether there is enough space for the fastening unit. The drawing does not determine strength but reveals geometric conflicts.

After selecting one line, the rest are removed from the working documentation so that the craftsman does not confuse the dimensions. The specification only retains the exact article number, dimensions, wood species, quantity, and fittings. This procedure is especially useful when simultaneously equipping a pedestal, chest of drawers, and sofa with different leg heights.

How to coordinate legs with handles, facades, and base

MN-214 is logically associated with parts that have pronounced planes: rectangular handles, frame facades with clear geometry, narrow vertical layouts. But complete repetition of the shape is not necessary. It is enough that the direction of the edges supports the main lines of the furniture, rather than creating a random angle.

MN-222 is easier to combine with rounded handles, soft facade transitions, and calm classic fittings. When painted in the body color, the turned shape becomes unobtrusive. With contrasting tinting, on the contrary, it noticeably separates from the body, especially at a height of 180 mm.

If the furniture has a decorative base or bottom strip, check whether it overlaps the leg profile. Sometimes a beautiful support is visible only for a few centimeters and loses its meaning. In such a situation, it is more important not to buy a more expressive model, but to change the offset or choose a shape that is readable in the accessible area.

In a set of several items, it is not necessary to use one article number. However, heights and finishes must be coordinated. For example, pedestals can stand on MN-222 120 mm, and a chest of drawers on MN-214 160 mm, if the difference is supported by the overall geometry and does not look like a random replacement. Such a solution is better shown in advance on a room layout.

Why it is better to make the final decision based on the set, not on a single detail

One leg on display shows the shape and quality of processing, but does not demonstrate the rhythm of four identical supports. In a set, the faceted MN-214 looks stricter because each plane repeats at the corners of the body. The turned MN-222 creates a softer repetition, but at a height of 180 mm becomes a noticeable part of the entire composition.

It is useful to place four samples or at least four paper silhouettes next to each other. This test shows whether the MN-214 overloads a small cabinet and whether the MN-222 120 mm seems too inconspicuous under a deep chest of drawers. After that, it is not abstract legs that are compared, but the future piece of furniture.

The complete approach also disciplines the estimate: it immediately accounts for four or another confirmed number of legs, fasteners, glides, finish, and cabinet preparation. It is this final configuration that should be convenient, stable according to the design, and justified in price.