Buy carved wooden table base: STL-011 assembled or STL-012 disassembled — which to choose

When you need to buy a carved wooden table base for a future tabletop, models STL-011 and STL-012 can easily be mistaken for almost identical options. Both have size A of 900 mm, both are made of beech or oak, and are available with "Standard" or "Prestige" sanding. The difference in dimensions is indeed small: STL-011 measures 900 × 750 × 330 mm, while STL-012 measures 900 × 760 × 332 mm.

However, the buyer is not choosing based on ten millimeters in parameter B or two millimeters in parameter D. The main difference lies in the delivery format. STL-011 is delivered assembled, so after receiving it, you can focus on checking the geometry, preparing the finish, and selecting the tabletop. STL-012 is delivered disassembled by default, with hardware included in the kit: the buyer needs to accept the parts, check the completeness, organize assembly, and only then proceed to installing the tabletop.

The delivery format affects the entire project: moving through doorways and staircases, storage space, risk of damage to the finished structure, requirements for the assembly area, access to joints, sequence of finishing, and involvement of a furniture maker. An assembled table base reduces the number of operations on site but takes up more space during transport. A disassembled one is more convenient for logistics but requires careful assembly according to the diagram and checking all connections.

Below are detailed specifications of STL-011 and STL-012, selection for different rooms and tabletops, beech and oak, "Standard" or "Prestige" sanding, acceptance of a rigid box, storage of parts, dry assembly, ordering errors, a "what to buy together" block, and the commercial route on STAVROS. Load capacity and universal compatibility are not made up: they must be confirmed by a specialist for the specific tabletop and table structure.

Buy STL-011 assembled Buy STL-012 with hardware View carved underframes

Carved Skirt STL-007

from 1,037.89 $

Carved Skirt STL-008

from 1,659.43 $

Carved Skirt STL-011

from 1,973.55 $

Carved Base STL-012

from 1,497.55 $

STL-023 Base

from 355.97 $

Pedestal for Table STL-027

from 2,628.40 $

Pedestal for Table STL-041

from 569.69 $

Baseboard for Table STL-042

from 566.77 $

Go to Catalog

STL-011 or STL-012: confirmed specifications

The table shows that STL-011 and STL-012 are in the same size group. The buyer should not exaggerate the difference of 10 and 2 mm, but should not ignore it either: precise fit under the countertop requires a drawing. The main question is different — is it more convenient to accept a ready-made assembled base or to organize the assembly of a disassembled kit with fittings.

Watch video ...

What STL-011 and STL-012 have in common

Both models belong to carved wooden underframes and are designed to create an expressive base for the countertop. Their size A is the same — 900 mm. This helps compare products within one design task, but does not mean automatic interchangeability. Sizes B and D, part shapes, connection points, and carving pattern must be checked against the card and drawing.

STL-011 and STL-012 are available in beech or oak. The buyer can choose the wood species depending on the future coating, wood grain, and combination with the tabletop. Both underframes are offered with "Standard" or "Prestige" sanding, so the surface preparation level is also included in the order and affects subsequent finishing work.

Both models arrive in a rigid box. This is important for protecting the carved structure, but the packaging does not exempt from acceptance. Before signing the documents, check the integrity of the box, the absence of visible impacts, the article number, and the number of packages. After unpacking, inspect the wood, decorative elements, joints, and completeness.

Neither model should be automatically declared compatible with any tabletop. Weight, size, shape, overhang, attachment points, and load distribution pertain to the entire table project. The underframe card helps select the base, and final compatibility is confirmed by a specialist after studying the tabletop.

Our factory also produces:

Baseboard for Table STL-026-2

from 454.66 $

Table base for STL-026-3

from 361.94 $

Baseboard for Table STL-026-5

from 463.44 $

Table leg STL-015

from 5,193.48 $

Base for table STL-020

from 2,627.06 $

Table pedestal STL-020-1

from 2,278.90 $

Baseboard for Coffee Table STL-035

from 813.31 $

Coffee Table Base STL-036

from 1,173.18 $

View Full Product Catalog

Main difference: underframe assembled or disassembled

What the buyer receives for STL-011

STL-011 is supplied assembled. This means the main base elements are already connected, and the buyer does not need to perform the initial assembly of the entire carved structure on site. After receipt, attention shifts to acceptance, geometry check, finish selection, installation site preparation, and tabletop coordination.

Assembled delivery is especially convenient if there is no separate workshop, qualified assembler, or time for parts sorting on site. It reduces the risk of mixing up parts or incorrectly orienting elements. However, the finished underframe takes up more space and requires a pre-checked delivery route.

The presence of an assembled structure does not mean the table is ready. The tabletop, its attachment, final finishing, and installation are done separately. Also, no conclusion about the permissible load can be drawn solely from the factory assembly. The load is determined by the entire system.

What the buyer receives for STL-012

STL-012 is supplied disassembled by default, and the hardware is included in the kit. This format is convenient for transportation, storage, and carrying through narrow doors, staircases, and elevators. Individual parts are easier to distribute in the car and carefully bring into the room.

The advantage comes with the responsibility for assembly. Upon receipt, check all parts and fittings, keep the packaging, and match the elements with the diagram. Assembly must be performed on a flat, protected surface, without pressure on the carved decor and without unauthorized replacement of fasteners.

If the buyer needs STL-012 assembled, such an option cannot be promised without confirmation. According to the initial data, the model is sent disassembled by default. Another format should be clarified in advance with the STAVROS manager and recorded in the order.

Direct comparison of delivery format

A disassembled delivery is neither worse nor better than an assembled one by itself. These are two different ways to organize a project. For a city apartment with a narrow staircase, STL-012 may be more rational. For a finished interior without a workshop, STL-011 can reduce the number of operations and the risk of errors.

When to choose STL-011

There is no space for assembly at the site

An assembled underframe is convenient when the room is already finished, free space is limited, and there is nowhere to unfold parts and tools. STL-011 can be unpacked, inspected, and prepared for the next stage without a full assembly area. This is especially useful for an apartment, a small office, or a finished showroom where furniture should appear without lengthy on-site work.

However, even an assembled model needs a safe area for unpacking. The threads must not touch the floor, walls, or metal tools. The tabletop is not installed immediately after delivery until the geometry, surface, and compliance with the order are checked. The assembled format reduces the volume of operations but does not eliminate careful acceptance.

The buyer needs to reduce the number of operations

If the project is handled by a customer without their own furniture workshop, STL-011 reduces the amount of manual work. There is no need to distribute parts, understand the sequence of connections, or control the initial tightening of fittings. Tasks related to the tabletop, coating, and installation remain.

Reducing operations does not mean the absence of a specialist. Attaching the tabletop, assessing stability, and final installation require a professional approach. An assembled delivery removes one stage but does not turn the underframe into a fully finished table and does not confirm universal load capacity.

The delivery route allows carrying the finished structure

STL-011 should only be chosen after checking doors, corridors, stairs, elevator, and turns. The dimensions 900 × 750 × 330 mm must be compared with the actual route, not just the room size. It is important to consider packaging and the ability to turn the box.

If the assembled underframe passes without risk, this format saves time. If the route is complex, the advantage may disappear: attempting to squeeze the finished product increases the risk of damaging threads, door trims, and walls. For a questionable passage, it is useful to make a cardboard mockup of the dimensions.

The drawing of STL-011 matches the project

The delivery format is important, but design remains an independent criterion. The buyer chooses STL-011 not only because it is assembled, but because its carved composition matches the tabletop, interior, and adjacent furniture. The similarity in dimensions of STL-011 and STL-012 does not make the designs interchangeable.

Before ordering, you can buy carved underframe STL-011, after checking the dimensions 900 × 750 × 330 mm, material, sanding, and current manufacturing conditions.

When to choose STL-012

Compact logistics is important

The disassembled format is useful for delivery to a room with difficult access. Parts are easier to carry through narrow doors, up stairs, and to fit in an elevator. This reduces the risk of the finished underframe colliding with corners, trims, and furniture.

The advantage only works with careful packaging and handling. Parts must not be carried by carved protrusions or stacked so that one part presses on another. The rigid box protects the set, but after opening, responsibility for safe arrangement passes to the recipient and assembler.

The underframe must be stored until the tabletop is ready.

If the tabletop is made later, the disassembled STL-012 may be more convenient for temporary storage. The box is placed in a dry, protected area where parts do not obstruct passage. An assembled structure would require more free space and be more vulnerable to accidental impacts.

Long-term storage should not occur in random conditions. The wood is protected from dirt and sudden environmental changes. Specific recommendations for storage and preparation for finishing are best clarified with the manufacturer and finisher.

The buyer is ready to arrange professional assembly.

STL-012 is rational if there is a furniture maker or craftsman on site who can check the completeness, assemble the base on a level surface, and control the connections. Hardware is included in the kit, but its presence and condition are checked immediately after unpacking.

Self-assembly is only permissible if the structure is understood and instructions are available. Hardware must not be replaced with random parts, connections must not be reinforced with arbitrary screws, and fasteners must not be tightened to the point of damaging the wood. An error in one joint can disrupt the geometry of the entire underframe.

The size and pattern of STL-012 fit more precisely.

STL-012 has dimensions of 900 × 760 × 332 mm. The difference from STL-011 is small, but in a precise furniture project, even 10 mm and 2 mm must be reflected in the drawing. The pattern and design may also better match the future tabletop and interior.

In the card, you can buy carved underframe STL-012 and check the delivery format, material, sanding, fittings, and current production time.

How important is the difference between 10 and 2 mm

For overall visual perception, the difference between B 750 and 760 mm, as well as D 330 and 332 mm, is small. You should not base your choice on the assumption that STL-012 is significantly larger. The models are similar in scale. The buyer is more likely to notice the difference in pattern, design, and delivery format.

In the drawing, these millimeters are still important. Mounting points, tabletop overhang, distance to the edge, and final symmetry are calculated based on the exact dimensions of the selected item. You cannot take the diagram for STL-011 and use it for STL-012 without verification.

You need to be especially careful when replacing the model after the tabletop has been approved. If holes, inserts, or a decorative frame have already been prepared, even a small difference may require adjustments. First, choose the underframe, then finally approve the tabletop and installation diagram.

How to choose a tabletop for STL-011 or STL-012

Tabletop shape

A rectangular, oval, round, or shaped tabletop interacts differently with the carved base. The shape should leave sufficient space around the underframe, support the composition, and not create random overhangs. There is no universal size in the source data, so it cannot be invented.

The plan shows the contour of the tabletop and the dimensions of the underframe. Then symmetry, position relative to the long and short sides, walkways, and chair placement are evaluated. The carved structure should be visible, not hidden under excessive overhang.

Length and width

Tabletop dimensions affect stability and load distribution. Too much overhang increases stress on the fasteners, while too little can visually compress the underframe. The decision is made by a specialist after studying the material and design.

For STL-011, its exact dimensions of 900 × 750 × 330 mm are used; for STL-012, 900 × 760 × 332 mm. The 900 mm dimension A for both models does not provide complete information, so calculation based on a single parameter is incomplete.

Weight and material

Solid wood, stone, glass, and panel materials have different weights and require different fastening methods. Compatibility with a heavy countertop cannot be promised solely because the underframe is made of wood. Data on weight, thickness, inserts, and loads are needed.

If the countertop has already been purchased, the specialist examines it before ordering the base. If the underframe is chosen first, the countertop design is built around the confirmed dimensions of the selected model.

Overhang and fastening points

The overhang affects the appearance and mechanics of the table. It must be coordinated on all sides and not interfere with chairs. Fastening points are placed where the countertop material allows for a secure connection.

For STL-012, the assembly connections of the underframe itself are considered separately. The countertop fastening should not hinder access to hardware or create stress in the already assembled structure.

Underframe for countertop: what to check before ordering

It is useful to study in advance how to choose a table base for a tabletop, then apply the recommendations to the exact dimensions of STL-011 or STL-012. The general guide does not replace the product card, but helps to form a list of questions for a specialist.

How to calculate the final table height

Size A 900 mm refers to the underframe, but the final table height depends on the design of the top part. The tabletop, mounting elements, and possible intermediate parts can change the surface level. 900 mm cannot be automatically called the final height of the finished table.

Before ordering, a vertical section is drawn. It marks the floor, the bottom point of the base, the top of the underframe, the mounting layer, and the tabletop. If the product is intended for specific chairs, the position of the seat, knees, and elbows is checked.

The same size A for STL-011 and STL-012 helps to compare them by height, but does not cancel the calculation. Different designs can affect the method of installing the tabletop, so a specialist must see the drawing of the selected model.

One tabletop and one underframe or another scheme

The number of bases depends on the size and design of the tabletop. One underframe may be used for one table, but for a long or heavy surface, the project may require a different scheme. It cannot be guaranteed in advance that one STL-011 or STL-012 is sufficient for any size.

If a long table is planned, the drawing shows the location of the base, possible additional supports, and areas of maximum overhang. Loads from people, objects, and the tabletop's own weight are evaluated as a single system.

Decorative expressiveness does not replace engineering calculation. A carved underframe is chosen by style and dimensions, and the structural scheme is confirmed by a furniture maker or designer.

Beech or oak for STL-011 and STL-012

When to choose beech

Beech is suitable when an even base for opaque or colored finishes is important. The specific type of coating in the card should be clarified; the article does not invent a ready-made color. Beech helps to connect the underframe with painted facades, doors, or furniture and make the carved base part of a unified color composition.

Carved relief requires careful application of the coating. A thick layer can soften small details, so before the main finishing, a sample is made and a technology suitable for the wood is chosen. For STL-012, it is important to consider the seating areas of the parts: the coating should not interfere with assembly.

When to choose oak

Oak is chosen when it is necessary to preserve the pronounced wood texture and connect the base with an oak tabletop, panels, or other furniture. Tinting and gloss level are approved on a sample because the natural pattern of different parts is never completely identical.

For STL-012, individual parts are best finished using a unified system so that they look cohesive after assembly. For STL-011, the assembled structure may require a different order of work since access to internal areas is limited. In both cases, the result is evaluated under the actual lighting of the room.

Why the material is chosen together with the tabletop

The underframe and tabletop do not have to be made of the same species, but their combination must be deliberate. Beech under an opaque finish can support a stone, glass, or painted tabletop. Oak texture can be combined with solid wood, veneer, and other wooden surfaces.

It is important for the buyer to determine in advance: the base should blend with the tabletop, support its shade, or contrast with it. Without this, the choice of species becomes random, and the finisher receives an undefined task.

Sanding "Standard" or "Prestige"

Both models are available in two sanding options. The choice depends on the requirements for the final surface, the type of coating, and the amount of subsequent manual preparation. The difference cannot be reduced to an abstract "better or worse": a project with thin transparent finishing and a project with dense opaque painting impose different requirements.

For a carved structure, the quality of recesses, transitions, and internal surfaces is important. Under side lighting, small irregularities become more noticeable. Therefore, the processing option is agreed upon before ordering, and the same level is used for all elements of one table.

Details view STAVROS requirements for product quality useful before selection. After receiving, the underframe is still inspected before coating and countertop installation.

Finish the underframe before or after assembly

For STL-011, the issue is resolved considering that the product arrives assembled. The finisher receives a ready-made structure and must ensure access to all visible areas without damaging the joints. Sometimes the assembled format is more convenient for uniform color control, but more difficult for internal zones.

STL-012 allows finishing parts before final assembly, if the technology and mounting points permit. This approach facilitates access to the relief, but the coating must be protected during joining. The thickness of the finishing layer should not interfere with the precise fit of parts and hardware.

There is no single universal order. It is agreed upon with the manufacturer, assembler, and finisher. It is important not to start coating before checking the completeness, dry assembly, and geometry. Otherwise, a hidden problem will appear after expensive finishing.

How to accept STL-011 in a rigid box

Upon receiving STL-011, first inspect the box. Dents, tears, signs of impact, and moisture are recorded before opening. Then check the labeling and compliance with the order. Since the assembled product is inside, the box is opened on a prepared area, without pulling the underframe by the carved elements.

After unpacking, inspect the external surfaces, joints, and geometry. The underframe is placed on a flat, protected surface and checked to ensure it does not wobble due to debris or floor unevenness. Any comments are recorded before finishing.

The STL-011 configuration must be matched against the card and order documents. The original diagram does not confirm a separate hardware list, so conclusions cannot be drawn by analogy with STL-012.

How to accept STL-012 and check the fittings

After inspecting the box of STL-012, check the quantity of wooden parts and the fittings kit. Lay out all elements on a soft, clean surface and compare them with the diagram. Do not start assembly until the presence of each item is confirmed.

Do not mix fittings with hardware from other products. Even similar parts may differ in length, thread, or purpose. If something is missing or a part is damaged, stop assembly and contact the seller.

Inspect wooden parts from all sides, especially joint areas. Carved protrusions should not serve as support during layout. Keep the packaging until the inspection is complete and all comments are recorded.

How to prepare a place for assembling STL-012

You need a flat, horizontal area that can accommodate all parts and tools. Cover the floor with a soft, clean material without abrasive particles. There should be no walkway nearby where someone could step on the fittings or damage the threads.

Before assembly, study the sequence and orientation of the elements. Do not fully tighten parts until the entire structure is pre-assembled and checked diagonally. The specific technique depends on the manufacturer's diagram.

If the buyer has no experience with carved furniture, it is wiser to hire a specialist. The cost of professional assembly may be lower than the consequences of a damaged joint, warped structure, or ruined finish.

How to check the geometry after assembling STL-012

Place the finished base on a flat surface. Check stability, symmetry, verticals, and joint positions. First, distinguish slight wobbling from floor unevenness: move the base to another spot and repeat the check.

Then the main dimensions are measured and compared with the card. The tabletop is not used to forcibly level a skewed base. If the geometry is not confirmed, the cause is sought before installing the top part.

All connections are tightened evenly according to the recommended pattern. Excessive force can damage the wood. A universal tightening torque is not specified in the initial data, so it cannot be invented.

Logistics: apartment, country house, and commercial property

Apartment with elevator

For STL-011, the cabin, elevator door, corridor, and turns to the room are measured. The assembled underframe may fit in size but not turn inside the cabin. STL-012 is usually easier to bring in as separate parts.

If the elevator is small, a disassembled delivery is often more convenient. However, the apartment must have space for assembly and a craftsman who can perform the work without damaging the finish. You cannot choose STL-012 solely based on the compactness of the box without planning further operations.

Staircase flight

On the stairs, the width, railing height, landings, and turns are important. A finished STL-011 cannot be pushed with force or leaned with threads against the wall. The route is checked considering the packaging and the number of people needed for safe lifting.

STL-012 reduces the dimensions of individual portable parts, but the box must still fit. Unloading is planned in advance, not at the moment of delivery. For complex stairs, photos and precise measurements sent to the manager or assembler are useful.

Country house

In a house, there is usually more space for bringing in and assembly, so the choice may be determined by work convenience. STL-011 saves time, STL-012 allows finishing parts before assembly and storing the kit until the room is ready.

If the object is still under construction, the under-table area is protected from dust, wet processes, and accidental impacts. The box should not be used as a stand for other materials, nor should the product be left near active finishing work.

Restaurant, hotel, or showroom

A commercial facility has a tight schedule and intensive use. The assembled STL-011 reduces one stage on site but requires unobstructed delivery. The disassembled STL-012 is convenient for logistics, but assembly must be included in the schedule.

Compatibility with the countertop and load is confirmed by the designer. The article does not replace the calculation of furniture for public

Where to use STL-012

STL-012 solves similar interior tasks but is more convenient in projects with complex logistics or phased finishing. The disassembled format helps deliver the product to an apartment, upper floor, niche, or facility with narrow passages.

The included hardware simplifies preparation if checked immediately. The model can be assembled after dirty work is completed, and stored in the box in a protected room until then. This is convenient when the countertop or finishing is prepared separately.

The STL-012 drawing must match the interior regardless of the delivery format. Choosing it only for the disassembled packaging without evaluating the appearance is wrong.

What to buy together with a carved underframe

The tabletop is not included in the table as a confirmed product because the SEO scheme did not provide a specific card. It is selected separately and must be coordinated with the underframe. It is better not to buy the top part randomly, relying only on the external size.

How not to confuse an underframe with a finished table

STL-011 and STL-012 are bases for tabletops, not fully finished tables. The buyer will need to select the top part, develop the mounting, perform finishing, and organize installation. Even an assembled STL-011 remains an underframe.

Do not look for confirmation of the finished table's parameters in the product card: the final height, weight, number of seats, and permissible load depend on the tabletop and the project. The correct commercial route starts with the base but ends with an agreed-upon set.

If a general selection is needed, you can study carved solid wood underframe: how to choose the base. The new article is dedicated to a narrower fork — STL-011 assembled or STL-012 disassembled.

How not to confuse STL-011 and STL-012 when ordering

The article numbers are similar, so the specification must include the full designation, size, and delivery format. For STL-011, 900 × 750 × 330 mm and assembled condition are fixed. For STL-012 — 900 × 760 × 332 mm, disassembled delivery by default, and hardware included.

It is not enough to send a photo to the manager or write "model 900 mm". Size A is the same. An error in the article number will be discovered too late if the tabletop is already calculated or the finish is approved.

The order also specifies beech or oak and the sanding option. After receipt, all items are checked against the documents before unpacking and work.

Mistakes when purchasing STL-011

Not checking the delivery of the assembled product

Even a suitable room size does not guarantee that the box will fit through stairs and doors. Solution: measure the entire route, doorways, elevator, landings, and turns in advance. For a questionable area, it is useful to make a mock-up of the external dimensions and check the possibility of turning.

Assuming the assembled delivery is a finished table

The tabletop and mounting remain a separate project. Solution: prepare a drawing of the complete product, determine the shape of the top part, mounting points, and final height. The assembled underframe shortens one stage but does not complete the furniture.

Assuming the same hardware as STL-012

In the original STL-011 scheme, the fittings are not specified separately. Solution: clarify the configuration in the card and order. Data from STL-012 cannot be transferred just because the models are close in size.

Do not check the geometry before finishing

After coating, it is more difficult to fix issues. Solution: perform acceptance, install the underframe on a flat surface, and conduct a dry fitting of the tabletop before priming, tinting, or painting.

Buy the tabletop before choosing the model

Exact dimensions and fastening may not match. Solution: first approve the underframe and connection scheme, then start production of the tabletop.

Errors when purchasing STL-012

Do not check the set of fittings

A missing element may be discovered on assembly day and stop the project. Solution: lay out the set and check it immediately after receipt, keeping the packaging and documents.

Assemble on an uneven or dirty floor

Threads and connections may be damaged, geometry may be distorted. Solution: prepare a flat, soft area, remove abrasive dust, and prevent people from walking through the work zone.

Replace fittings with random parts

Similar fasteners may have different parameters. Solution: use a kit and only approved replacements. Unauthorized reinforcement of connections can damage the wood.

Finish parts before trial assembly

The coating may interfere with fitting or hide a problem. Solution: first check the kit, perform a dry assembly, confirm the geometry, and only then approve the finish.

Consider the disassembled delivery simple for any buyer

Without a specialist, the assembly stage can become a risk. Solution: assess skills, tools, space, and cost of professional work in advance.

Common mistakes when choosing two models

The first mistake is exaggerating the difference in dimensions and ignoring the delivery format. The second is choosing only by format without comparing the carved pattern. The third is considering the same size A as proof of full interchangeability. All three mistakes lead to incorrect expectations from the purchase.

It is also dangerous to promise compatibility with any tabletop, a specific load, or a universal mounting method. This data depends on the full project and is not confirmed by the original diagram. The buyer needs an honest boundary of applicability, not a promotional promise.

Finally, you cannot postpone checking the material and sanding. The underframe may fit logistically but not match the chosen finishing system. All parameters are approved simultaneously, not after receiving the product.

Who is STL-011 suitable for

STL-011 is suitable for a buyer who wants to receive an assembled carved base and reduce the number of operations after delivery. The model is especially convenient for a finished interior without a workshop, provided there is a free delivery route and storage space for the finished structure.

It is suitable when the size 900 × 750 × 330 mm and the pattern match the project, and the tabletop will be designed for a specific base. Beech or oak and sanding are chosen in advance so that the finisher receives a clear technical specification.

STL-011 may not be suitable if the underframe cannot be brought in assembled, the site is on a difficult floor, the product needs to be stored for a long time in a confined space, or the buyer wants to finish each part separately.

Who is STL-012 for

STL-012 is suitable for a project where disassembled logistics are more convenient. It is useful for narrow passages, limited elevators, phased finishing, and the need to store the kit until the room is ready. The included hardware helps prepare for assembly.

The model is suitable for a buyer who can organize professional work on site. The size 900 × 760 × 332 mm and the carved pattern must be coordinated with the tabletop and interior.

STL-012 may not be suitable if the site lacks space, tools, and a specialist for assembly. In this case, the advantage of disassembled delivery turns into additional risk and costs.

How to store STL-011 before installing the countertop

An assembled underframe takes up more space than a box with individual parts. It is placed in an area where the structure will not be accidentally moved and where carved elements do not come into contact with tools, walls, or other objects. The base must not be used as a temporary table, material stand, or support during renovation.

The underframe is installed on a flat, protected surface. If the finishing is not yet completed, the wood is covered from dust and dirt, but a random airtight package is not created without manufacturer recommendations. It is better to clarify storage and preparation conditions for finishing with STAVROS and the finisher.

Before installing the countertop, the product is inspected again. During storage, room conditions may have changed, new furniture or finishing elements may have appeared. The movement route from the storage location to the installation point is also rechecked.

How to store disassembled STL-012

STL-012 is best stored in its original rigid box until the assembly area is prepared. The box is not placed in a passageway and is not loaded with heavy materials on top. The labeling is preserved to avoid confusing the kit with another product.

After opening, parts are laid out only for inspection. If assembly is postponed, each element is returned to a protected position, and the fittings are stored in a labeled bag. Losing one small part can stop the entire project.

Do not finish part of the set and leave the remaining parts uncontrolled. All elements of one underframe undergo the same technology and are then assembled according to the scheme.

How to coordinate the color of the underframe and countertop

Color can be built according to three scenarios: close match, calm related combination, or contrast. For a match, samples of both surfaces and a unified assessment under real lighting are needed. For a related combination, the shade temperature and degree of gloss are important. For contrast, a deliberate difference is needed, not a random mismatch.

A carved surface reflects light differently than a flat countertop. The same shade on a relief may appear darker in recesses and lighter on protrusions. Therefore, the paint sample is evaluated not only on a flat board but also on a sample with similar geometry.

STL-011 assembled and STL-012 in parts may require different painting organization, but the final coating system must remain uniform for the entire product.

How to plan project timelines

For STL-011, the calendar includes manufacturing, delivery, acceptance, finishing, tabletop preparation, and installation. The assembly stage of the underframe itself is shortened, but logistics of the finished product may require a separate date, transport, and team.

For STL-012, hardware inspection, dry assembly, final assembly, and geometry control are added. If finishing is done on individual parts, the schedule is coordinated so that the coating has time to achieve the necessary properties before joining.

The tabletop cannot be ordered based on an unconfirmed drawing. It is better to first finalize the underframe model and obtain the necessary dimensions, then proceed with the top part. This reduces the risk of rework and schedule delays.

How to estimate a budget without a made-up price

The project cost consists not only of the underframe price. The budget includes the selected wood species, sanding, finishing, tabletop, fastening, delivery, carrying in, assembly, and installation. STL-011 may reduce the cost of on-site assembly work, but finished logistics may be more complex. STL-012 is easier to transport but requires professional assembly.

Models should be compared based on the full estimate. Being cheaper in one item does not always mean it is more advantageous for the entire project. If the room does not allow bringing in STL-011, trying to save on assembly will lead to additional costs.

The current price is checked in the product card after selecting the material and sanding. The article does not fix the cost because it may change and depends on the order parameters.

How to prepare a technical specification for the manager

The request includes the article number, material, sanding, desired delivery format, address, and access features. For STL-012, separately ask about the hardware kit and instructions. For STL-011, ask about the delivery contents and box dimensions if needed for logistics.

The request includes tabletop data: shape, dimensions, thickness, material, and weight, if known. If the tabletop has not been selected yet, describe the table's purpose, number of seats, and interior scenario.

The more accurate the initial data, the lower the risk of receiving a formal response without compatibility checks. It is useful for the buyer to ask specific questions rather than requesting "any 900 mm underframe."

How to buy STL-011 or STL-012 at STAVROS

Start by checking the object. Measure doors, stairs, elevator, and storage space. If the assembled base fits and it is important to reduce assembly work, open the STL-011 card. If logistics are complex and there is an opportunity to assemble the product on site, study STL-012.

Then select the material and sanding. Beech or oak are considered together with the finish and tabletop. "Standard" or "Prestige" are chosen based on surface requirements. Do not leave these parameters for later: they are part of the product order.

After selecting the article, coordinate the tabletop. Provide the specialist with its shape, length, width, thickness, weight, and material. Get confirmation of the attachment method and overall structure. Check the current price, availability, and production time in the card or with a manager.

If the two models are not suitable, you can buy solid wood underframes in a different size or view the catalog of carved underframes.

Checklist before placing an order

FAQ: STL-011 or STL-012

1. How is STL-011 different from STL-012?

The main difference is the delivery format. STL-011 comes assembled, STL-012 comes disassembled by default and includes fittings. The dimensions are close but not identical.

2. What is the size of STL-011?

The confirmed size is 900 × 750 × 330 mm.

3. What is the size of STL-012?

The confirmed size is 900 × 760 × 332 mm.

4. Which underframe is supplied assembled?

STL-011 is supplied assembled.

5. Which underframe is supplied disassembled?

STL-012 is supplied disassembled by default.

6. Are fittings included with the STL-012 kit?

Yes, the original diagram confirms that the fittings are shipped as part of the set. Their presence should be checked upon receipt.

7. Are the fittings included in the STL-011 set?

In the provided data, they are not listed separately. The configuration should be clarified in the product card and with the manager before ordering.

8. Can the STL-012 be ordered assembled?

By default, the model is supplied disassembled. The possibility of a different delivery method must be separately confirmed with the STAVROS manager.

9. What should I choose for an apartment with a narrow staircase?

The disassembled STL-012 may be more convenient for carrying in, but space and a specialist for assembly will be required. The route still needs to be measured.

10. What should I choose if there is no workshop on site?

The assembled STL-011 reduces the number of operations. However, the countertop, finishing, and installation remain separate tasks.

11. Is beech or oak better for the underframe?

The choice depends on the future covering and countertop. Beech is suitable for projects with opaque finishes, oak — when it's important to preserve the wood texture. The specific technology is agreed upon separately.

12. What is the difference between "Standard" and "Prestige"?

These are options for sanding quality. Details should be viewed in the STAVROS quality section and selected considering the final coating.

13. Will any countertop fit?

No. You need to consider the shape, size, weight, material, overhang, and fastening. Compatibility is confirmed by a specialist.

14. Can a heavy stone countertop be installed?

Such a decision cannot be confirmed without calculating the entire structure. A specialist must evaluate the weight, fastening, and load distribution.

15. Is size A 900 mm the height of the finished table?

Not necessarily. The final height depends on the installation method and the thickness of the countertop.

16. Does STL-012 need to be assembled before finishing?

It is useful to perform a dry assembly and check the geometry before the final coating. The final sequence is coordinated with the finisher.

17. How to check STL-011 upon receipt?

Inspect the rigid box, markings, surfaces, joints, and geometry before finishing and installing the countertop.

18. How to check STL-012 upon receipt?

Inspect the box, count the wooden parts and fittings, check the connection areas, and keep the packaging until the acceptance is complete.

19. Where to buy STL-011?

In the product card of the carved table base STL-011 on the STAVROS website.

20. Where to buy STL-012?

In the product card of the carved table base STL-012 on the STAVROS website.

21. How to find out the current price?

Open the card of the selected model and check the order parameters. The price may depend on the material and finish.

22. How to find out the production time?

Check the current time in the product card or with a STAVROS manager before placing an order.

If the countertop already exists: which option is safer to choose

A ready-made countertop changes the selection order. The buyer can no longer freely adjust the top part to the preferred base: they need to check the actual dimensions, weight, thickness, location of embedded parts, and material condition. In this situation, STL-011 and STL-012 are compared not only with each other but also with the existing structure.

First, take precise measurements of the countertop and photograph the underside. Then mark the intended position of the base, the overhang size, and access to the fastening. If holes or embedded parts are already made, the specialist must confirm whether they can be used with the selected model. New points cannot be drilled without verification, especially for stone, glass, and complex composite materials.

STL-011 is convenient when the assembled base can be immediately applied to the countertop and the composition checked. STL-012 allows you to first lay out the parts and evaluate the installation zones, but the final base still needs to be assembled according to the diagram. The delivery format does not automatically solve the compatibility issue.

If the table is being designed from scratch

A new project gives more freedom. The buyer can first choose STL-011 or STL-012, get confirmed dimensions, and only then develop the countertop. This order reduces the risk of rework because the top part immediately takes into account the selected base, its pattern, and attachment points.

For STL-011, the project includes bringing in the assembled base. For STL-012, it includes an assembly area, technician time, and hardware control. The countertop is designed simultaneously with the overall height, number of seats, and distance to legs or carved elements.

Before starting production, it is useful to make a simple mockup: mark the base dimensions on the floor, and at the required height, the edge of the tabletop. The mockup shows how freely people can pass, whether it is comfortable to sit, and whether the upper part does not look excessively large relative to the carved under-table.

How to measure doorways and the delivery route

For STL-011, it is not enough to measure only the width of the front door. You need to go through the entire route from the car to the installation site: vestibule, elevator, stair landing, corridor, turns, interior doors, and furniture already in the room. The narrowest point determines the possibility of delivery.

Measure the width and height of each opening, as well as the depth of the areas where the crate will need to be turned. Consider handles, door closers, railings, and protruding architraves. If the door can be temporarily removed, this is discussed in advance, but it is not considered a guaranteed solution.

For STL-012, the route is simpler since the crate contains separate parts, but the external packaging size still needs to be clarified. A disassembled model should not be chosen blindly just because it seems compact. Proper logistics begins with the actual delivery dimensions.

How to perform a dry fit of the tabletop

A dry fit is performed without final fastening. The under-table is placed on a level surface, and the tabletop is carefully placed on top, observing safety measures. Check centering, evenness of overhangs, access to fastening points, and overall appearance.

For STL-011, such a fit is possible after receiving the assembled base. For STL-012, only after proper assembly and geometry check. Do not use a heavy tabletop as a tool for aligning joints or use it to press down a skewed structure.

After the fit, take photos from several distances. The carved under-table should be visible under the top part, and the tabletop should not appear accidentally shifted. If the project includes chairs, also place them in position and check for free space.

How to choose a model for a dining, office, or interior table

Dining table

For a dining table, seating capacity, leg positioning, and stability under regular use are important. STL-011 is convenient if the assembled base can be brought in and quickly prepared for installation. STL-012 helps solve complex logistics but requires professional assembly before mounting the tabletop.

The tabletop size must be confirmed by a specialist. The number of seats cannot be determined solely by size A 900 mm: the shape of the base and overhangs affect the available space.

Office table

In an office, the carved base often becomes the main decorative element. In addition to appearance, the placement of the chair, cables, drawers, and equipment is checked. Assembled STL-011 reduces work in a finished office, while STL-012 is easier to deliver to a room with difficult access.

If the table is used daily, the design must account for lateral loads and top fastening. Decorative pattern does not replace structural verification.

Interior and display table

For a hall, salon, or showroom, the underframe can be used under a decorative or display tabletop. Here, the view from all sides and combination with lighting are especially important. STL-011 and STL-012 are similar in scale, so the pattern and work organization format come to the forefront.

In a commercial space, assembly, finishing, and installation are included in the overall schedule. Disassembled STL-012 cannot be left on site without a responsible master, and assembled STL-011 cannot be left without a protected storage area.

Care for the finished table on STL-011 or STL-012

Care depends on the chosen finish coating, not just the wood species. The buyer needs to get recommendations from the finisher: how to clean the surface, which products are prohibited, and how to protect carved recesses from dust accumulation.

The carved relief is cleaned gently, without harsh abrasives and excessive moisture. Care rules cannot be transferred from one coating system to another. Tinted oak, painted beech, and clear varnish may require different products.

Periodically check the condition of the tabletop fastening and connections. For STL-012, special attention is paid to assembly units, but any adjustments are made without excessive tightening. If the table starts to wobble, first check the floor and overall geometry, then contact a specialist.

What questions to ask the manager before payment

For STL-011, clarify the current configuration, material, sanding, delivery condition, packaging, production time, and parameters needed for bringing in. For STL-012, the same questions plus the composition of hardware, availability of instructions, and the possibility of an alternative delivery format if needed.

A separate block of questions is dedicated to the countertop. Is it necessary to provide its drawing? What data is needed to check compatibility? What method of fastening is intended? Are there any installation restrictions? It is better to get answers before final payment and production launch.

Also clarify the acceptance procedure and actions upon detecting packaging damage. The buyer must understand what documents and photos are needed so that the remark is processed without delay.

Why a ready-made underframe is better than a random set of parts

STL-011 and STL-012 are created as coordinated carved structures. The buyer does not need to independently search for random legs, crossbars, and decorative elements, try to connect different profiles, and achieve a unified geometry. The finished model reduces the risk of pattern and scale mismatch.

STL-011 is supplied already assembled, so the consistency of the structure is immediately visible. STL-012 comes as a kit with hardware and is intended for assembly as a single product. This is fundamentally different from an independent set of parts without confirmed connections.

A ready-made underframe does not eliminate the work on the countertop and installation, but it allows you to focus on those stages that should truly be individual: the size of the top part, finish, color, fastening, and placement in the interior.

Result: STL-011 assembled or STL-012 disassembled

STL-011 and STL-012 have the same size A 900 mm, are made of beech or oak, and are available with "Standard" or "Prestige" sanding. STL-011 has dimensions of 900 × 750 × 330 mm and is supplied assembled. STL-012 has dimensions of 900 × 760 × 332 mm, is supplied disassembled by default, and comes with hardware.

STL-011 is chosen when the finished structure fits the route and the number of assembly operations needs to be reduced. STL-012 is chosen when compact logistics, storage in a box, and on-site assembly are important. The size difference is small, so the final decision is determined not only by millimeters but also by the pattern, access to the site, buyer's resources, and project schedule.

Before ordering, check the countertop, final height, fastening method, material, and finish. Do not transfer dimensions from one article to another and do not calculate load based on appearance. On STAVROS you can view STL-011, go to STL-012 card or compare others Carved furniture frames and table bases.