The plate on MN-241 is already installed, but screws are not included: how to order modern wooden supports and pre-arrange fasteners with the tabletop

The buyer chose modern wooden supports MN-241 for the table. On the product page, everything looks almost ready for assembly: each leg already has a metal mounting plate 2 mm thick installed, and the support itself is designed for direct attachment to the tabletop without an apron. A natural question arises: if the plate is standard, why doesn't the manufacturer include universal screws or bolts in the set?

The reason lies in the tabletop itself. The same MN-241 can be used with different furniture projects, and the material, thickness, and structure of the underside of the tabletop vary. Universal fasteners that work equally well for solid wood, MDF, plywood, composite construction, or a reinforced tabletop cannot be specified based only on the leg's product page.

Therefore, the purchase needs to be divided into two parts. The first is already decided by the manufacturer: wooden support → standard metal plate. The second must be decided by the furniture maker: standard plate → specific tabletop. It is for this part that fasteners, support placement, and allowable fastener insertion depth are selected.

If the project is already defined, you can buy the modern furniture leg MN-241, but before paying for the batch, you need to provide the tabletop data to the furniture maker and get a confirmed mounting assembly.

Modern Furniture Leg MN-241

from 159.81 $

Go to Catalog

Modern furniture leg MN-241: what is included in the order and what is purchased separately

The current MN-241 card shows one size configuration:

742×160×95 mm.

Materials — beech and oak. Sanding quality — only “Prestige”. Base preparation — “For enamel”.

At the time of verification, the price:

The card also confirms:

• frameless application scheme;
• installed metal mounting plate;
• plate thickness 2 mm;
• attachment directly to the tabletop through the plate;
• Self-tapping screws or screws for attaching to the tabletop are not included in the kit;
• Fasteners are selected separately depending on the material and thickness of the tabletop.

That is, the phrase "the leg comes with a plate" is not equal to the phrase "the leg is fully equipped with fasteners for any tabletop."

When ordering, it is better to write down the product line in full immediately:

MN-241 / 742×160×95 mm / beech or oak / Prestige / For enamel / quantity ___ pcs. / standard metal plate installed / fasteners for tabletop to be selected separately.

If the buyer is still choosing supports, you can first buy furniture legs through the general category. But if MN-241 is already approved, you should not return to the general selection, but close the mounting issue for this specific model.

Watch video ...

The plate is installed by the manufacturer, but the mounting assembly is not yet complete

It is convenient to represent the assembly as two connections.

First:

MN-241 → metal plate.

It is already done on the product.

Second:

Metal plate → tabletop.

Here it depends on the specific project.

This difference is fundamental. The buyer sees metal on the upper part of the leg and may think that all that remains is to "screw it on with something suitable." But the choice of fastener affects how the connection works with the specific tabletop material.

Therefore, you cannot place a separate order for self-tapping screws at the same time as the legs if the furniture maker does not yet know what exactly the plate will be attached to.

First, the tabletop gets its own specification. Then the contractor chooses the fastener.

Our factory also produces:

Wooden Capital KL-010

from 136.63 $

Wooden Decor N-352

from 29.81 $

Wooden molding K-066

from 27.76 $

Wooden Decor N-276

from 100.66 $

Decor Set C-049

from 389.62 $

Stool Frame STL-026-7

from 274.83 $

Furniture Handle Rubicon HL-034

from 13.28 $

Wooden decor N-493L

from 12.79 $

View Full Product Catalog

What tabletop data is needed before ordering four MN-241

Before the final purchase, the furniture maker needs to provide at least basic information about the top.

Material

Solid wood, MDF, plywood, combined furniture board, or another structure — these are different bases.

Thickness

It limits the allowable fastener depth and affects the mounting solution.

Underside device

The tabletop can be solid or have a backing layer, reinforcement, frame, recess, technological zones, or other construction.

Location of each support

You need to know where the plate will actually be relative to the edge, reinforcements, and other elements.

Available depth for fasteners

It is determined by the furniture maker based on the actual construction.

Overall table construction

The number of supports, tabletop dimensions, its mass, and usage scheme are considered as a single project.

The article does not assign a universal screw size because one MN-241 card is not enough for such a solution.

Why you cannot select a screw based only on the 2 mm plate thickness

The thickness of the metal plate is 2 mm.

This figure is useful as a characteristic of a standard part, but it does not answer the main question: what fasteners are needed for a specific tabletop.

From 2 mm, one cannot derive:

• the length of the self-tapping screw;
• diameter;
• the thread type;
• the head shape;
• the allowable insertion depth;
• the need for a pilot hole;
• suitability for a specific material.

Incorrect logic:

Plate 2 mm → we take a self-tapping screw of a certain length.

Correct logic:

There is a 2 mm plate → there is a specific tabletop → the furniture maker checks its material and thickness → after that, selects the fastener.

That is why the manufacturer does not make one universal set for all possible tables.

MN-241 and a solid wood tabletop: the fastener is approved as a single assembly unit.

If the top is made of solid wood, it does not mean you can use any "wood screw."

It is necessary to determine the specific tabletop thickness, the direction and location of attachment, the distance from the edge, and the actual structure of the underside surface.

The mounting assembly is convenient to fix as follows:

MN-241 + standard plate + specific tabletop + selected fastener = finished connection.

If the tabletop is later changed, for example, instead of one solid wood piece another construction is chosen, the fastener specification must be rechecked.

It cannot be assumed that a solution approved for one table automatically transfers to the next just because the support remains MN-241.

MDF, plywood, or a composite tabletop: do not automatically transfer the old fastener from another table.

Another common mistake occurs with a furniture maker who has already assembled a similar table.

The logic looks like this:

In the previous project, four legs were held by such screws — let's take the same ones.

But the previous table could have had a different thickness, a different bottom part, reinforcement, or a different material.

Even two tabletops of the same thickness do not necessarily have the same construction.

Therefore, the new project must have its own mounting list.

It states:

Tabletop: ___
Thickness: ___ mm
Bottom layer: ___
MN-241: ___ pcs.
Standard plate: installed
Fasteners: to be selected and confirmed with the cabinetmaker.

This way, the buyer does not try to solve an engineering problem based on a product photo.

Frameless MN-241: why fasteners must be approved before assembly

MN-241 is designed for frameless use: the leg is attached directly to the tabletop through a metal plate.

Visually, this is a strong point of the design. There is no massive apron between the legs, leaving more free space under the table, and the furniture itself looks lighter.

But that is exactly why the plate-to-tabletop connection cannot be left for installation day.

In a traditional table, the apron is a separate structural element. In the case of MN-241, the design follows a different logic, and the point where the leg attaches directly to the tabletop becomes a fundamental part of the entire structure.

The buyer receives a beautiful finished leg with the plate installed, but the table project must cover the rest of the assembly unit.

Buying four furniture legs does not mean getting four ready-made mounting assemblies

Suppose the designer confirmed four MN-241.

In cart:

MN-241 × 4.

This means four wooden supports with standard plates.

But the installation list should include one more solution:

Fastening the plate to the tabletop — select based on the material and thickness of the tabletop.

Without this line, the product purchase is complete, but the table project is not yet.

If you specifically need the series of wooden supports, you can Buy wooden furniture legs, but the completeness of a specific installation unit is always checked separately.

How much do four MN-241 made of beech and oak cost

For the calculation, we'll take a hypothetical project where the table structure already confirms four supports. This is an example, not a universal rule for any table.

Beech

One MN-241 — 13,240 ₽.

Four:

4 × 13 240 = 52 960 ₽.

Oak

One MN-241 — 17,010 ₽.

Four:

4 × 17 010 = 68 040 ₽.

The difference:

68 040 − 52 960 = 15 080 ₽.

This amount cannot automatically include:

• fasteners to the tabletop;
• tabletop;
• finish;
• installation;
• delivery;
• tabletop reinforcements, if required by the project.

The price of four legs is the price of supports, not the price of a finished table.

Beech or oak: the material is chosen before the overall finishing

MN-241 is available in beech and oak.

This article does not need a general debate about which wood is "better".

For procurement, something else matters more: the selected material must be recorded together with the quantity and finish.

For example:

MN-241 / oak / 4 pcs. / Prestige / For enamel.

Even if the entire tabletop is planned for opaque painting, you still cannot accidentally mix two materials in one batch just because one item turned out to be more available.

If the tabletop material is visible and the project is based on a combination of textures, the choice of wood species becomes an even more noticeable visual decision.

MN-241 "Prestige": we do not include a non-existent Standard in the estimate.

In the current MN-241 product card, it is shown only with the "Prestige" sanding finish.

This is an important point for the purchaser.

You cannot write on your own:

MN-241 / beech / Standard

just to reduce the estimate, if such a standard configuration does not exist in the product table.

If the project requires a different level of processing, it must be discussed separately with the manufacturer. Until this is confirmed, the working specification should contain exactly "Prestige".

"Prestige" refers to the quality of sanding, not to the color or the type of paint coating.

"Under enamel" does not mean a ready-painted leg

The base configuration of MN-241 is specified as "Under enamel".

This is preparation of the workpiece for further opaque finishing.

It does not mean that the leg is already painted in white, black, or another color.

For the project, the following must be separately defined:

• final color;
• the primer system;
• enamel;
• gloss level;
• finishing contractor;
• moment of trial assembly.

A good sequence:

1. confirm the table geometry;
2. confirm the support locations;
3. select the fasteners;
4. perform a control check of the assembly;
5. then carry out the final finishing according to the project's technological map.

Thus, the craftsman is not forced to experiment with an already finished expensive part.

Why the standard MN-241 plate does not need to be automatically replaced with another one

With MN-241, the metal plate is already installed by the manufacturer.

Therefore, the buyer does not need to go to the general catalog of mounting plates and look for "something more suitable" just because the fastening to the tabletop is missing.

It is not the plate itself that is missing.

Screws or bolts for connecting the standard plate to a specific tabletop are selected separately.

Replacing the standard plate with another product is already a separate design change that must have a technical reason and be agreed upon with the furniture maker.

Do I need to order a floor support along with MN-241?

The product page recommends the FUR-022 floor support as related hardware.

But it cannot be automatically added to every specification just because it is shown nearby.

Need to clarify:

• whether this particular project needs a floor support;
• whether it is provided for in the scheme;
• how many are required;
• how it affects contact with the floor;
• how it is accounted for in the final geometry.

The main topic of this article is attaching the top plate to the tabletop. The foot should not distract from the main mounting solution.

What to write to the furniture maker before purchasing MN-241

The work order might look like this:

Support: MN-241
Product dimensions: 742×160×95 mm
Quantity: ___ pcs.
Material: beech / oak
Sanding: Prestige
Preparation: For enamel
Standard mounting plate: installed, metal, 2 mm
Tabletop: material ___
Thickness: ___ mm
Bottom side structure: ___
Plate fastening to tabletop: select by material and thickness
Check fastening before final finishing and installation

Such a line is much more useful:

"Need screws for four legs MN-241".

The second phrase lacks half of the data needed for selection.

Trial assembly of one unit before installing four legs

If the table is being designed for the first time, it is useful to first assemble one control unit.

The furniture maker takes one MN-241 and a section or the actual tabletop, checks the plate position, available fastening depth, and correctness of the chosen scheme.

The goal is not to test the table for maximum load, but to confirm that the mounting specification physically matches the real part.

If the control unit requires changes, they are made before serial installation of the remaining three supports.

This is especially useful when the countertop is expensive or already has a finish coating.

What to check on the drawing before payment

Before purchasing, it is useful to go through several points together with the furniture maker:

• actual dimension MN-241;
• position of the standard plate;
• mounting points;
• location of each support under the countertop;
• countertop overhangs;
• distance to the edge;
• possible reinforcements;
• final table structure.

There is no need to try to extract this data from a single product photo.

The card confirms the presence of the installed plate and the principle of direct attachment, and the project must confirm the specific geometry of all furniture.

If the tabletop material has changed after ordering the legs

Let's imagine that MN-241 has already been ordered for a project with a tabletop made of one material, but the designer later changes the top to another.

The legs themselves may remain the same. The size of MN-241, the wood species, and the standard plate do not change just because the top has changed.

But the installation specification needs to be reopened.

You cannot transfer the old line to the new project:

fasteners — as in the previous version.

A new tabletop means a new question for the furniture maker:

• what material is now being used;
• what is its actual thickness;
• is there a backing or reinforcing layer;
• where does the safe mounting zone run;
• does the previous position of the supports match the new design;
• can the previously selected fasteners be retained.

Thus, changing one element does not turn into a hidden error of the entire assembly.

It is especially important to record the date of the change. In the working set, it is useful to leave:

Countertop version 1 — canceled.
Countertop version 2 — use for selecting fasteners MN-241.

This is a simple revision control that protects the project from a situation where the purchaser works with the new countertop, and the installer receives the old fastener list.

Four MN-241 need to be marked on the countertop before final finishing

Even if the project confirms four supports, it is important to know not only the quantity but also the position of each.

On the underside of the tabletop or on the working drawing, it is convenient to mark:

H1, H2, H3, H4.

For each position, record:

This table does not specify engineering distances. It forces the designer and the furniture maker to confirm that all four plates fall within the allowable zones of a specific tabletop.

If one support ends up over a cutout, seam, insert, or other structural feature, this is detected before final assembly.

Therefore, "four identical legs" do not mean "four absolutely identical mounting locations." The geometry of each point is better checked on the drawing.

Acceptance of MN-241 after delivery: what to check before painting and installation

When the supports arrive at the site, they should not be immediately sent for finishing.

First, the goods themselves are checked against the order.

For each leg, check:

• part number MN-241;
• dimensions 742×160×95 mm;
• material — beech or oak;
• sanding "Prestige";
• preparation "Under enamel";
• presence of a standard metal plate;
• absence of expectation that screws for the tabletop should be in the package.

If four legs are ordered, it is useful to place them side by side and check the completeness of the entire batch before installation.

At the same time, the article does not set height tolerances and does not promise absolute identity with natural wood. Acceptance is carried out according to the placed order and confirmed characteristics.

After that, the furniture maker checks the plate against the design tabletop again. Only when the mounting assembly is confirmed can the supports be sent for final finishing.

The final table height cannot be calculated only by the formula "742 mm + tabletop"

Size A=742 mm is specified in the MN-241 card, and naturally there is a desire to simply add the tabletop thickness to it.

But for the production task, it is safer to rely on the current drawing and the actual installation scheme.

The reason is simple: the final mark of the finished table depends not only on the commercial figure, but also on how exactly the tabletop interfaces with the standard plate and what additional layers are provided by the project.

Therefore, instead of the phrase:

742 mm + 40 mm = finished table 782 mm

in the working documentation, it is better to write:

Confirm the final height against the current drawing MN-241 and the actual tabletop construction.

This is especially important if there is an additional layer, cladding, reinforcement, or other composite structure underneath.

This way, the article does not turn one product size into an unconfirmed installation dimension.

When four MN-241 units are not yet needed to be purchased

It is better to stop the order if:

• the tabletop material has not been selected yet;
• its actual thickness is unknown;
• the lower structure is changing;
• leg positions are not marked;
• the furniture maker did not see the card and drawing MN-241;
• the customer is sure that universal screws should be included;
• the tabletop is already drilled for a different type of support;
• the designer is still changing the table size;
• no one is responsible for selecting fasteners.

Under such conditions, buying four beautiful legs does not solve the problem. It only shifts it to installation.

Errors when ordering MN-241

Error: considering the plate a complete mounting kit. The plate is installed, but fasteners to the tabletop are selected separately.

Error: choosing a screw based on the plate thickness of 2 mm. This parameter is not sufficient. Tabletop data is needed.

Error: transfer the mounting hardware from the previous table. A new project may have a different material and thickness.

Error: purchase four legs before approving the layout. The quantity of items is not yet an installation project.

Error: record MN-241 Standard. The current table standardly specifies the "Prestige" sanding.

Error: consider "Under enamel" as finished paint. This is preparation for the future finish.

Error: replace the installed plate with another without reason. This is already a change to the product design.

What phrase should be in the procurement specification

Finished product line:

MN-241 / 742×160×95 mm / beech or oak / Prestige / Under enamel / quantity ___ / standard metal mounting plate 2 mm installed / screws or bolts for attaching to the tabletop are not included / fasteners to be selected according to the material and thickness of the tabletop.

For a conditional project of four beech supports:

MN-241 / 742×160×95 mm / beech / Prestige / Under enamel / 4 pcs. / standard mounting plate / tabletop fasteners to be agreed separately.

This way, the buyer understands what they are purchasing, and the furniture maker sees the uncovered part of the mounting assembly.

Where to buy wooden legs MN-241 for a table

If the design has already been tested, you can proceed directly to MN-241.

If the model is still being compared with other modern supports, a seating option is convenient where you can buy wooden table legs.

For a wider selection, available are buy furniture legs and supports, but for the already approved MN-241, the main next step is not a new search, but coordinating the tabletop and fasteners.

Questions before purchasing MN-241

What is the size of MN-241?

742×160×95 mm.

What materials are available?

Beech and oak.

What sanding is specified in the card?

"Prestige".

Is there an MN-241 Standard?

In the current product table, "Prestige" is shown as standard. Another option cannot be considered available without separate confirmation.

What does "under enamel" mean?

This is preparation for subsequent opaque finishing, not a ready-made paint coating.

Is there a mounting plate?

Yes. The metal plate is already installed on the support.

What is the thickness of the plate?

2 mm.

Are self-tapping screws or screws for the tabletop included?

No. The card clearly states that they are selected separately.

Why doesn't the manufacturer include universal fasteners?

Because the material and thickness of tabletops vary, so fasteners are chosen for the specific structure.

Can I choose a self-tapping screw based only on the plate thickness?

No. 2 mm is not enough for such a solution.

Can I use fasteners from the previous table?

Only after a new check of the tabletop and the assembly unit. It cannot be transferred automatically.

How much do four beech MN-241 legs cost?

At the current price of the items — 52,960 ₽.

How much do four oak MN-241 legs cost?

68 040 ₽.

Is the tabletop included in this amount?

No. This is the cost of four legs at the current price.

Can I buy four legs and choose the mounting hardware during assembly?

Technically, it's not advisable to postpone the decision until installation. The mounting hardware should be agreed upon before purchase, or at least before final finishing and assembly.

Where can I see other wooden table legs?

In the category of unpainted table legs STAVROS.