Polyurethane molding NPU-362.1R

Imagine an interior where molding lines start flawlessly, guide the eye along the wall, and then — abruptly end. Just a cut, a corner, emptiness. It is this moment of incompleteness that is eliminatedPolyurethane molding NPU-362.1R: a right-hand carved tip for moldings measuring 54 × 26 × 11 mm, which turns the mechanical end of the profile into an intentional, ornamentally designed endpoint of the system.

NPU-362.1R can be purchased on the STAVROS website from 330 rubles per piece, with shipment from one unit. The product is included in thecatalog of decor for moldingsand is designed for systems based on moldingsMLDPU-001and MLD-001-MG — delicate profiles of the first STAVROS series with a cross-section of 10 × 6 mm. This is direct factory compatibility, requiring no additional fitting or verification.

Molding decor NPU-362.1R: the right side of the system is as important as the left

In decorative architecture, symmetry works as a law. The molding horizontal strip, framing a doorway, decorative niche, or accent wall, has two ends — left and right. The left one closesNPU-362.1L. The right one — NPU-362.1R. Without one of them, the system looks incomplete, even if everything else is executed flawlessly.

The 'R' in the article number stands for Right — right-handed. The finial's ornament is asymmetrical: its relief pattern unfolds from the narrow tip to the wide mounting base precisely in the direction corresponding to the right end of the molding. If NPU-362.1R is placed on the left end of the profile, the ornament will be oriented 'against the flow' of the system, which is immediately considered a mounting error. Therefore, the correct choice between L and R is not a technical issue but a matter of architectural literacy.

What is a carved finial for molding and why is it needed

A carved finial is a decorative finishing element mounted on the end of a molding profile. In architectural tradition, all horizontal decorative elements — moldings, cornices, belts, pediments — were finished with special accents: acroteria, brackets, rosettes, finials. This was not a decorative whim but a structural principle: a line must have a beginning and an end, otherwise it is not a line but an unfinished thought.

NPU-362.1R reproduces this tradition in a modern execution: an affordable, easy-to-install, moisture-resistant polyurethane finial with a clear floral ornament. It solves a specific task in the first series STAVROS molding system — and solves it in the only correct way: through direct factory compatibility with MLDPU-001 and MLD-001-MG.

Compatible with moldings MLDPU-001 and MLD-001-MG

Compatibility is not just a word in the description. It is specific parameters by which the finial and molding form a single whole: the width of the mounting plane, the relief height at the connection point, the style of the ornament. NPU-362.1R was created together with the first series STAVROS moldings — not alongside them, but precisely together.

MLDPU-001: thin decorative beading 10 × 6 × 2600 mm

Molding MLDPU-001— is a polyurethane profile with a cross-section of 10 × 6 mm and a strip length of 2600 mm. Thin, elegant, delicate — beading for wall panels, furniture fronts, framing decorative systems in small and medium-sized rooms. A width of 10 mm means this is not a monumental architectural profile but an intimate decorative accent: a line that organizes space without overwhelming it. Price from 1,370 rubles per 2600 mm strip.

For a profile 10 mm wide, the NPU-362.1R finial with a 26 mm mounting plane is the correct ratio: the finial is 2.6 times wider than the molding, which in architectural practice corresponds to the 'bracket — beam' proportion. An accent wider than the supporting element is traditional classical logic.

MLD-001-MG: primed MDF with identical cross-section

MLD-001-MG is a first series molding made of high-density MDF with factory primer coating. Geometric parameters match MLDPU-001. The surface is acrylic primer applied during production. The molding is supplied completely ready for final painting.

In the MLD-001-MG + NPU-362.1R system, two materials—MDF and polyurethane—are fused into a single unit: after final painting in a unified layer, the boundary between them visually disappears. Both materials accept standard interior paints and coatings equally, without discrepancies in tone or texture. This is a fundamental practical advantage of system compatibility.

Three roles in the first series system

The complete decorative system based on MLDPU-001 includes three functional positions:

• MLDPU-001 molding — the main line, horizontal or vertical

• Corner blocksMLDPU-001U— 90° turns, system corner finishing

• NPU-362.1L (left) and NPU-362.1R (right) tips — finishing of horizontal end points

NPU-362.1R closes the third position — on the right side. Without it, the system technically functions, but architecturally remains incomplete. This is precisely the purpose of the product.

Product characteristics NPU-362.1R

Length-to-relief-height ratio: 54 mm to 11 mm — this is a 20% protrusion from the product length. For a tip of this format, this is a balanced volume: sufficient for the ornament's readability from a normal viewing distance (1.5–3 m), but not overloaded, not creating 'heaviness' on the thin profile of the first series.

The NPU marking (Non-Porous Urethane — in STAVROS terminology: non-porous foamed two-component polyurethane) means a dense surface layer with an elastic internal structure. The surface layer ensures the ornament's detail and smoothness for painting, the internal structure provides cushioning during installation.

Advantages of the NPU-362.1R polyurethane decor

Shape consistency: not a millimeter of deviation between batches

Reaction injection molding in closed molds is a technology where the mold determines the result. Every NPU-362.1R specimen in any batch is identical to the others within the precision of the manufacturing tolerance. This is important when you order several tips for a symmetrical system: all right tips will match each other, and between them — and with the left NPU-362.1L — there will be no visual discrepancy.

For comparison: in manual plaster casting, tolerances are 30–50% higher, and two products from the same batch can noticeably differ. Polyurethane casting eliminates this risk completely.

Delicate weight: installation without unnecessary movements

NPU-362.1R weighs a few grams — literally. With such weight, the only necessary fastener is mounting adhesive for polyurethane. No drilling, no screws, no risk of damaging the wall's finish. On drywall, plaster, MDF, and other flat substrates, the adhesive holds the product securely and permanently.

Resilience Instead of Fragility: Ornament Retains Detail

Fine details of an ornament on a small item are a risk zone for fragile materials. In plaster, sharp edges of the ornament chip. In PSB, they deform under pressure. In two-component polyurethane, they spring back and return to shape. NPU-362.1R preserves the relief during transportation, installation, and years of operation.

Stability in Any Climate: No Deformations or Cracks

NPU polyurethane is chemically neutral to water and stable in a temperature range from -40°C to +50°C. Seasonal humidity fluctuations in living spaces—from dry heating periods to humid off-seasons—do not affect the geometry of the item. The ornament relief installed today will be identical to its current state in five, ten, twenty years.

Ready-to-Paint Surface Without Intermediate Processing

The surface of NPU-362.1R is smooth, without pores or burrs. After installation—apply primer, let dry, apply finish enamel. No putty layers, no reinforcement, no special preparation. In a mixed system with primed molding MLD-001-MG, both elements are painted in a single technological sequence.

Price More Affordable Than Expected

NPU-362.1R price—from 330 rubles. Consider: a decorative carved finial with an ornament, factory precision geometry, and direct compatibility with the STAVROS molding system—for 330 rubles. This is one of those cases where cost and value are measured in different units. The value of the architectural completeness of the system is incomparably higher than the cost of the part that ensures this completeness.

Visual Features of the Decorative Element NPU-362.1R

Asymmetric Floral Ornament: Pattern with Direction

NPU-362.1R belongs to the type of carved finials with directional ornamentation: the relief pattern develops from the narrow tip to the wide base along a right-handed axis. The floral motif is a traditional form for finishing decorative elements in classical and neoclassical architecture. Leafy scrolls, smooth transitions, organic curves — the language of nature, adapted to architectural discipline.

The directionality of the ornament visually 'guides' the eye along the molding line to its right-hand completion: the eye moves along the profile and gently stops at the finial, which makes it clear — the line ended here intentionally, not by chance. This is the very 'final flourish' spoken of in calligraphy. In architectural decor, it works exactly the same way.

11 mm relief: volume without overload

With a product width of 26 mm, an 11 mm relief constitutes about 42% of the cross-sectional dimension. This is a pronounced volume that creates a readable shadow under side lighting. Under direct overhead light — from ceiling spotlights — the finial reads as a sculptural detail with a soft contour. Under grazing light from a wall sconce or floor lamp — the shadow from the relief deepens, creating an illusion of greater volume.

For a thin molding 10 × 6 mm (MLDPU-001), a finial with an 11 mm relief creates the correct accent: it protrudes more than the profile — and it is precisely this difference in volume that helps the eye fix the endpoint of the system.

Compact format without loss of expressiveness

54 × 26 мм — это мебельный масштаб. Не монументальный архитектурный акцент, а деликатная деталь, соразмерная интерьерам с молдингом первой серии: небольшим и средним помещениям, мебельным фасадам, оконным и дверным наличникам. В таком масштабе выразительность достигается не размером, а качеством рельефа и точностью орнамента. NPU-362.1R обеспечивает оба параметра.

Stylistic range of application

The floral ornament of NPU-362.1R is compatible with several interior styles:

• Neoclassicism — a delicate white accent in a molding system on a neutral wall

• Classic — part of multi-level decorative schemes with multiple contours

• Provence — natural motifs resonate with this direction

• Art Deco — strict geometry of molding + ornamental accent

• Transitional style — classical lines in a modern context

• Modern classic — minimal details, impeccable precision of each

Where to use decor for NPU-362.1R moldings

Above door and window openings

This is the first and most obvious scenario. The horizontal molding MLDPU-001, mounted above a door opening as part of a casing or portal, ends at the side vertical posts of the opening. The right end of the profile is covered by NPU-362.1R, the left by NPU-362.1L. A three-element system: molding + two tips. Result: an architecturally framed opening instead of just a rectangular hole.

A similar logic applies to window openings: horizontal moldings above and below the window are finished with tips, vertical ones are connected by corner blocksMLDPU-001U. A complete window frame in the style of classic casings — made from four types of elements, installed in a few hours.

Accent walls: TV area, headboard, wall behind the sofa

Accent walls with molding decor are one of the most common modern interior techniques. MLDPU-001 moldings organize the wall surface into a decorative scheme: horizontal lines, vertical dividers, frame accents. Each horizontal line has endpoints that need to be finished. NPU-362.1R is the finishing of the right endpoint.

The article STAVROS discusses the principles of constructing such decorative systems."Wall molding: photos, design ideas"Horizontal molding accents without properly finished endpoints are incomplete sentences in the architectural text of a wall. NPU-362.1R puts a period where it's needed.

Furniture fronts with molding overlays

The MLDPU-001 molding was originally created, among other things, for furniture applications — this is indicated by the profile description as a 'bead for wall panels and furniture fronts.' The 54 mm NPU-362.1R is organic in furniture scale: it's not an architectural finial for a three-meter wall, but a detail proportionate to a cabinet door or a dresser drawer. On furniture doors and horizontal molding overlays, NPU-362.1R finishes the right horizontal profiles just as it is done in historical joinery furniture.

The principles of correctly combining molding details in furniture are described in the article STAVROSabout classic furnitureFinishing details — finials, brackets, corner elements — determine the final perception of a product's class no less than its material or construction.

Decorative horizontal belts and cornices

In classical and neoclassical interiors, horizontal belts made of moldings divide the wall into visual zones: plinth, main field, frieze. Where such a belt made of MLDPU-001 is interrupted by a doorway, niche, or architectural projection, the right end of the belt is finished with the NPU-362.1R tip. Neat, professional, within the system.

Decorative frames around mirrors and panels

In interior solutions with decorative frames around mirrors, paintings, or decorative panels, the MLDPU-001 molding forms the perimeter of the frame. At points where the frame does not close completely—for example, with symmetrically diverging 'wings' of decorative framing—the right horizontal ends are finished with NPU-362.1R. This gives the system an intentional, 'designed' character instead of a mechanically assembled set of profiles.

Installation and selection of NPU-362.1R: precision at the final stage

Before purchase: three questions to resolve

First: which molding in the system? NPU-362.1R is designed for the first STAVROS series—MLDPU-001 and MLD-001-MG. For moldings of other series (second, third), tips of the corresponding series are needed. Mixing series means getting elements with incompatible proportions that will 'clash' visually.

Second: orientation. NPU-362.1R is right-handed. Count all right end points of horizontal moldings in the system. For left ones—NPU-362.1L.

Third: quantity. Add 10–15% reserve to the calculated number of products. This rule is relevant for all small decorative elements: reordering often causes delays that slow down the final stage of work.

Surface preparation

The base must be:

• clean—without dust, grease, or remnants of old paint

• dry — humidity no more than 8–10%

• even — irregularities in the base transfer to the gap between the product and the surface

• primed — acrylic primer in the installation area improves the adhesion of the glue to the surface

On new drywall — apply acrylic primer, let dry for 2–4 hours, only then glue the tip.

Installation protocol: glue activation is critically important

1. Apply mounting glue for polyurethane to the back side of NPU-362.1R — in dots or a thin snake pattern

2. Attach to the marked spot on the surface, press briefly

3. Be sure to pull away from the surface — this step is most often skipped

4. Hold for 3–5 minutes in an open state — the glue 'activates' upon contact with air

5. Press firmly against the surface, hold for 5–10 seconds

6. If necessary, secure with painter's tape until fully set (1–2 hours)

Steps 3 and 4 are critical. It is during the open exposure that the adhesive gains initial adhesion. Without this step, even a lightweight product will not achieve the necessary initial bond, and the tip may slide or detach from the surface.

Joint finishing and final painting

After the adhesive has fully set:

1. Apply acrylic sealant in the color of the finish coating to the joint between the tip and the molding

2. Allow to dry, sand with 180-grit sandpaper

3. Apply acrylic primer in a single coat over the entire surface of the system (molding + tip + sealant)

4. Allow to dry, repeat priming if necessary

5. Finish with enamel in 2 coats with intercoat drying

After painting, the joint between NPU-362.1R and molding MLDPU-001 (or MLD-001-MG) becomes virtually indistinguishable. The system appears as a single monolithic product.

Why you should buy NPU-362.1R

There are interiors that seem 'almost finished'—yet still give a sense of incompleteness. Usually, the reason lies in details like these: a molding without an end cap, a frame without corner pieces, a decorative band with exposed ends. It's not a disaster, but it's a flaw that's impossible to miss if you look closely. And professional clients and designers look exactly that way.

Order decor for NPU-362.1R moldings—is an investment in completeness. For 330 rubles per piece, you get a right-side carved end cap with a floral pattern, 11 mm relief, direct factory compatibility with MLDPU-001 and MLD-001-MG moldings, and predictable results with final painting.

Full STAVROS molding decor catalogallows you to select all system elements at once: moldings, corner blocks, left and right end caps. Pickup in Moscow and St. Petersburg, delivery across Russia via SDEK and DPD.

Key characteristics of NPU-362.1R:

• Right-side (R) carved end cap, 54 × 26 × 11 mm

• Two-component polyurethane NPU—flexible, moisture-resistant

• Factory compatibility with MLDPU-001 (10 × 6 mm) and MLD-001-MG

• Floral pattern, 11 mm relief

• Surface ready for painting without putty

• Installation with adhesive, without fasteners

• Price from 330 rubles, shipment from 1 piece

Frequently asked questions about NPU-362.1R polyurethane molding

How does NPU-362.1R differ from NPU-362.1L?

NPU-362.1R is a right-handed tip, NPU-362.1L is a left-handed one. This is a mirrored pair: the ornament is asymmetrical and oriented in different directions. For a symmetrical molding system, both tips—right and left—are needed in equal quantities.

Which moldings does NPU-362.1R suit?

NPU-362.1R is designed for the first series STAVROS moldings:MLDPU-001(polyurethane, 10 × 6 mm) and MLD-001-MG (primed MDF, similar cross-section). Direct factory compatibility in size and ornament proportions.

Do tips need to be purchased in pairs?

When installing symmetrical horizontal moldings — mandatory. One end of the profile is a left tip, the other is a right tip. For asymmetric solutions where the molding goes into a corner or a wall on one side, a tip of the required orientation is sufficient.

How to calculate the quantity of NPU-362.1R for a project?

Count all right endpoints of horizontal moldings in the system. Add 10–15% reserve. When decorating multiple rooms, order with up to 20% reserve: reordering small items often gets delayed.

Can it be mounted on drywall without additional fasteners?

Yes. The mass of NPU-362.1R is negligible — polyurethane mounting adhesive provides reliable adhesion with the correct application protocol: apply, remove, wait 3–5 minutes, press. Additional mechanical fasteners are not needed.

Is NPU-362.1R compatible with moldings from other STAVROS series?

NPU-362.1R was created for the first series. For third-series moldings (MLDPU-003, MLD-003-MG), third-series tips and decor are used — for example, from theMLDPU-003 decor catalog. Mixing series is not recommended: the proportions of ornaments and bearing planes differ.

What types of paints and coatings are suitable for the NPU-362.1R surface?

Water-based, acrylic, alkyd paints and enamels — no restrictions. The surface accepts paint without prior puttying. Application of one coat of primer before the finish coating is recommended.

Where to buy NPU-362.1R and what is the price?

NPU-362.1R price — from 330 rubles per piece. You can buy molding NPU-362.1R in the STAVROS online store at the website stavros.ru from one piece. Pickup in Moscow and St. Petersburg, delivery throughout Russia.