Buy a round tabletop: ST-001 from MDF 1200 mm for a dining table or ST-027 660 mm for a coffee table — which to choose

Buying a round tabletop seems like a simple task until two seemingly related but completely different models appear side by side. ST-001 has a diameter of 1200 mm and is designed for assembling a full dining, family, or conference table. ST-027 is significantly more compact: its diameter is 660 mm, so it is primarily intended for a coffee or side table. The difference between the models is not just the 540 mm in diameter. The buyer chooses the scale of furniture, usage scenario, material, edge profile, finishing method, and suitable base.

ST-001 is made of MDF, has dimensions of 1200 × 1200 × 25 mm, and is supplied as a furniture blank for custom painting. This is a large round MDF tabletop for a DIY table, not a finished kitchen work surface for a sink or hob. ST-027 has dimensions of 660 × 660 × 30 mm, a distinctive shaped edge profile, and is available in MDF or a combined version using MDF, solid wood, and beech or oak veneer. This model helps assemble a compact table near a sofa, armchair, or in the center of a small lounge area.

The main mistake is to consider ST-001 and ST-027 as two sizes of the same product. The surface area of ST-001 is approximately 3.3 times larger than that of ST-027. The large model requires a stable base, free space for chairs, and a well-thought-out walkway around the table. The compact ST-027 solves a different problem: it should be conveniently placed near upholstered furniture, not obstruct movement, and keep the shaped edge profile visible.

For a full dining or conference table, consider the round MDF tabletop 1200 mm ST-001. If a tabletop for a coffee table is needed, you can buy tabletop ST-027 and choose a compact base for it.

Tabletop ST-001 from MDF

from 146.02 $

ST-027 countertop

from 89.42 $

Go to Catalog

Short answer: ST-001 or ST-027

ST-001 is chosen for a full-sized table. Its diameter is 1200 mm, thickness is 25 mm. The model is made of MDF with "Prestige" sanding and is designed for subsequent opaque painting. This surface is suitable for a dining, family, or conference table if the room allows space for chairs and walkways, and the base is designed for a large circle.

ST-027 is chosen for a coffee or side table. The model's diameter is 660 mm, thickness is 30 mm. The tabletop has a shaped profile and can be made of MDF or in a combined version with a solid wood edge and surfaces veneered with beech or oak veneer. MDF is suitable for opaque enamel, while veneer options allow preserving the wood grain with tinting, varnish, or patination.

Quick links to products and accessories:

• Buy tabletop ST-001
• buy tabletop ST-027
• Choose a base for a round tabletop
• View all tabletop sizes

Watch video ...

Why one round shape does not make tabletops interchangeable

The round shape solves several understandable problems. It has no sharp corners, all places are arranged around a single center, and the piece of furniture is perceived as softer than a rectangular one. However, the same contour geometry does not mean the same purpose. In furniture, the diameter determines not only the usable area, but also the distance between people, the depth of access to the center, the scale of the base, and the necessary free space around it.

ST-001 with a diameter of 1200 mm is perceived as a full-fledged table. On such a surface, you can organize a family dinner, a meeting, negotiations, or collaborative work. However, the actual number of comfortable seats cannot be determined solely by the diameter: you need to consider the width of the chairs, the design of the underframe, the position of the legs, and the requirements of the specific project. A table with an incorrectly chosen base may have a large surface but interfere with legs and create an uncomfortable seating position.

ST-027 with a diameter of 660 mm is a compact item. It should not replace a dining tabletop just because there is little space in the room. A coffee table is used differently: you place a cup, book, decorative item, remote control, or small serving on it next to the sofa. People do not sit around it the same way as around a dining table, and the height is determined by the chosen coffee table underframe.

The role of the edge also differs. For ST-001, a large calm circle should support the overall silhouette of a full-fledged table and not conflict with the base. For ST-027, the shaped profile is a noticeable part of the design. It is especially well visible at a low height and next to a carved underframe. If the table is pushed too far under the sofa or the edge is covered by upholstered furniture, part of the decorative effect is lost.

Our factory also produces:

Wooden Handrail L-082

from 35.01 $

Decor set C-002-1-2

from 499.67 $

Wooden Decor N-203

from 16.35 $

Wave HL-006 Furniture Handle

from 11.96 $

Hill HL-021M Furniture Handle

from 24.40 $

Sopp HL-042M Furniture Handle

from 18.79 $

Wooden bracket KR-068L

from 451.36 $

Rubio Monocoat Oil Plus 2C, Component A, Pure

from 9.86 $

View Full Product Catalog

Confirmed characteristics of ST-001 and ST-027

Characteristics show that the choice cannot be made on the principle of "bigger or smaller". ST-001 and ST-027 belong to different furniture scenarios. A large tabletop requires a full base and seating area. A compact model requires a base of coffee table height and good visual coordination with the shaped edge.

How much the diameters and surface area differ

The diameter of ST-001 is 540 mm larger than the diameter of ST-027:

1200 − 660 = 540 mm.

The difference is even more noticeable in area. The area of a circle is calculated using the radius. For ST-001 it is approximately 1.13 m², for ST-027 — about 0.34 m². Therefore, the surface of ST-001 is about 3.3 times larger.

This difference affects several decisions at once. First, a large surface has a greater overhang from the center of the base to the edge. The farther the edge is from the support area, the more carefully you need to check the stability of the structure under load. Second, ST-001 requires space around it for chairs and movement. Third, the diameter changes the scale of the item: the table may look appropriate in a spacious dining room and excessively large in a small walkway area.

ST-027 takes up much less space. It is easier to place in front of a sofa, between armchairs, or in a study, but even a small table cannot be placed without checking the walkways. The edge should not interfere with getting up from the sofa, opening drawers of adjacent furniture, or moving between zones.

The thickness of the models differs in the opposite direction: ST-027 is 5 mm thicker than ST-001. This does not make the compact model structurally "stronger" without calculation, but it affects the final appearance and height. With the same base, the top of ST-027 will be 5 mm higher if the mounting assembly does not add other differences.

Comparison of options for the buyer

After such a check, it usually becomes clear which card is needed. If the buyer plans a table for sitting and working, ST-001 becomes the main candidate. If a small table near upholstered furniture is required, ST-027 should be considered.

When to buy a round tabletop ST-001 1200 mm

Buy round tabletop 120 cm — a suitable query for a buyer who is assembling a large standalone table, not a kitchen countertop. ST-001 is designed for a noticeable furniture piece. It is chosen not only by color or shape, but also by how the table will be used every day.

For a family dining table

A round surface helps bring people together around a common center. But with a diameter of 1200 mm, you need to check not only space for plates and serving. It is important to ensure that the base does not interfere with legs, chairs can be freely moved back, and the passage remains convenient even when people are sitting at the table.

ST-001 is suitable for a project where furniture is assembled for a specific room. The buyer can choose the enamel color to match the underframe, facades, wall panels, or other furniture. However, matching the color does not mean the tabletop automatically becomes part of the kitchen set. The purpose and mode of use remain furniture-like.

For a conference or work table

A diameter of 1200 mm allows creating a round communication zone. In a conference room, it is important to be able to see interlocutors without a pronounced "main" end, as with a rectangular table. In a home office or studio, such a surface can be used for collaborative work, laying out materials, or discussions.

The base must match the actual load. On a work table, there may be equipment, documents, and other items, and people may lean on the edge. Therefore, the underframe is chosen not only by appearance. You need to check stability, support area, attachment to MDF, and load distribution.

For a modern interior under enamel

ST-001 is made of MDF, so it makes sense to use it where a smooth, opaque surface without visible wood grain is needed. White, black, or colored enamel can tie the table to the interior. The specific color and type of finish are selected in the project; current finishing options must be clarified before ordering.

A large circle looks good in a modern space if the base does not overwhelm the form. A calm edge allows either the tabletop color or the sculptural base to take center stage. If both the top and bottom have active decoration simultaneously, the composition can become heavy.

When a single color for the tabletop and base is required

MDF for opaque painting is convenient for projects where natural texture is not needed. The tabletop and base can be visually unified with one color or, conversely, create contrast. However, the same color designation does not guarantee a perfect match without a unified finishing technology. Materials, primers, gloss level, and application method affect the result.

Therefore, it is useful to approve a sample before production. This is especially important if the tabletop, legs, and other parts are painted in different workshops or at different times.

When not to choose ST-001

ST-001 is not suitable if the room cannot comfortably accommodate a circle with a diameter of 1200 mm along with chairs. It should also not be considered as a ready-made tabletop for installing a sink, hob, or for continuous use in a kitchen cabinet setting. The possibility of special use is agreed upon separately regarding construction, coating, and operating conditions.

If a small table near the sofa is needed, ST-001 will be excessively large. In this case, it is better to switch to ST-027 rather than try to adapt a dining tabletop to coffee table height.

When to choose the compact ST-027 660 mm

Round tabletop for coffee table ST-027 was designed for a different scale. Its diameter of 660 mm allows you to assemble a coffee or side table that complements the soft seating group and does not require space for full seating around it.

For a table in front of the sofa

In front of the sofa, balance between surface accessibility and freedom of movement is important. The table should be close enough to reach comfortably, but not obstruct standing up or passing by. A universal distance cannot be assigned without the dimensions of the sofa and the room. Verification is done based on the actual layout.

ST-027 is convenient because the round contour does not create sharp corners in the movement area. However, compactness does not eliminate the need for measurement. If the living room is narrow, even 660 mm can take up a significant part of the passage.

For a coffee table next to an armchair

Next to an armchair, ST-027 can work as a standalone piece. The surface has enough space for a cup, a book, a small lamp, or a decorative composition. The shaped edge is clearly visible from the side and adds expressiveness to the furniture.

In this scenario, it is especially important to calculate the height. A table that is too high will be uncomfortable next to a low armchair, while one that is too low will lose functionality. The final height is determined by the base, the tabletop thickness of 30 mm, and the mounting assembly.

For a classic living room

Combined options with beech or oak veneer help preserve the wood grain. This suits an interior that already has wooden cornices, door trims, carved furniture, or decorative panels. However, ST-027 cannot automatically be called solid wood: its construction includes MDF, solid wood edging, and veneer on the surfaces.

If a more subdued colored piece is needed, you can choose a version made of MDF with opaque enamel. Then the shaped profile will be read through light and shadow, rather than wood texture.

For a bedroom or study

A compact round table can be placed next to an armchair, by a window, or in a small reading area. In a bedroom, it can replace a large coffee table if a surface for a book or decorative items is needed. In a study, it can become part of a soft seating area.

When choosing, it is necessary to check that the table does not block the opening of doors, drawers, or cabinet doors. The round shape reduces the risk of accidentally hitting a corner, but does not compensate for incorrect placement.

When ST-027 is not suitable

ST-027 is not designed to serve as a full dining tabletop. The 660 mm diameter is intended for a compact table, not for regular seating of several people with full place settings. It should not be chosen as a 'small dining table' without a separate design justification.

The product should not be used outdoors just because the option includes wood. The card does not confirm continuous use under rain, frost, and UV exposure. Such a scenario requires separate data on the material, coating, and construction.

Dining table or coffee table: the main difference

A dining table is designed around a person sitting on a chair and using the surface at a specific height. A coffee table is designed around upholstered furniture and a different user posture. These items cannot be distinguished only by tabletop size: they have different heights, bases, loads, and spatial behavior.

For ST-001, seating positions, legroom, and stability under edge load are critical. A large circle has a significant overhang from the center, so a too-narrow base can lead to instability. Four random legs chosen only by style do not guarantee a safe and comfortable design.

For ST-027, the connection with the sofa or armchair is more important. The base must match the coffee table height, and the shaped profile must remain visible. A too-large or heavy underframe can visually overwhelm the compact tabletop. A too-thin one can look random and fail to provide necessary stability.

Countertops also differ in user interaction. People sit at ST-001 for extended periods, moving dishes, documents, and other items. ST-027 is used more occasionally and is considered part of a lounge area. Therefore, the finish in both cases should match the actual scenario, but the requirements may differ.

How diameter affects room size

The buyer often compares the countertop diameter only to the wall length. For a round table, this is insufficient. You need to imagine not just one circle, but several zones around it: the countertop itself, the position of chairs, space for pulling them out, and a walkway.

Checking ST-001 in the room

Draw a circle with a diameter of 1200 mm on the room plan. Then add the actual dimensions of the selected chairs. Show them in two positions: pushed in and pulled out. After that, check movement to doors, kitchen, window, and adjacent furniture.

This diagram immediately shows whether the table fits functionally, not just geometrically. Sometimes the circle physically fits in the room, but after installation, it's impossible to comfortably pull out a chair. In another case, a walkway remains only when no one is sitting at the table.

The base also takes up space. A central pedestal and a system of multiple legs affect seating differently. A central support can free up the edge but must be designed for stability. Spread-out legs can increase the support area but interfere with legs if poorly positioned.

Checking ST-027 next to upholstered furniture

For a coffee table, draw a circle of 660 mm on the plan and check the distance to the sofa, armchairs, and walkways. It's important to consider not only the static position of the furniture but also how a person stands up, sits down, and moves between objects.

If the table is to be placed in the center of a seating group, check accessibility from all sides. If it is positioned by a single armchair, ensure it does not interfere with the armrest and leg movement.

A shaped profile is better perceived when there is visual space around the end. If the tabletop almost touches the sofa, part of the decorative shape will be hidden.

How much space to leave around a round table

It is incorrect to give a single number for any interior. The width of the passage depends on the room's purpose, number of users, chair sizes, door placement, and traffic intensity. Instead of a universal number, use sequential checking.

First, mark the edge of the tabletop. Then place real chairs or their templates. Check how far they slide back when seated. After that, assess the remaining passage. If there is a wall behind a seated person, one scenario requires less space than a passage to another room that is constantly used.

For ST-001, it is especially important to check the path between the kitchen and the table if the furniture is in the dining area. A person with dishes should not have to squeeze between chair backs and the wall.

For ST-027, movement around the sofa is checked. The coffee table should not create an obstacle on the main route. If the room is small, a different layout can be considered, but functional gaps cannot be reduced just to fit a specific model into the plan.

MDF or a version with beech and oak veneer

The choice of material affects not only the appearance but also the finishing method. ST-001 is offered in MDF. ST-027 provides more options: MDF for enamel or a combined version with a solid wood edge and beech or oak veneer.

ST-001 made of MDF

MDF is suitable for smooth opaque painting. There is no need to preserve the natural wood grain on the surface, so color and finish quality become the main focus. This option is convenient for a modern interior, a painted underframe, or a project where the table must match other furniture.

MDF countertop under enamel requires professional preparation and a coating that matches the operating conditions. The material itself without finish should not be considered a ready-made work surface. Before ordering the finish, you need to agree on the primer, color, gloss level, and protective properties of the coating.

ST-027 made of MDF

The MDF option is chosen when a shaped edge is needed, but wood texture is not. Opaque enamel emphasizes the profile relief with light and shadow. The table can be made light, dark, or colored to match the interior.

This solution pairs well with a painted base. But if the top and bottom have different materials, the shade must be checked on samples. The same color may appear differently on MDF and wood.

ST-027 with beech veneer

The combined version with beech includes an MDF base, a solid wood contour frame, and beech veneer on the surfaces. Beech has a calmer pattern than oak, making it well-suited for even tinting and a restrained classic interior.

This option cannot be called solid wood. The buyer receives a combined construction that preserves the look of natural wood on visible surfaces and allows for a shaped profile.

ST-027 with oak veneer

Oak is chosen when a more pronounced pattern is required. Tinting and clear lacquer help emphasize the texture. Patina can further highlight the profile if provided for by the project and finishing technology.

Oak veneer countertop ST-027 especially appropriate next to a carved oak underframe. But matching the wood species does not guarantee a complete shade match without joint finishing and a sample.

How to choose between beech and oak

If the interior requires an active wood texture, oak is often considered. If a calmer pattern and even tinting are needed, beech is suitable. But the final decision is made based on actual samples, because natural material has variability.

The article helps to compare materials in more detail how to choose the tabletop material: solid wood, MDF, or veneer. For ordering ST-027, refer to the current options in the product card.

Calm or figured edge profile

The edge significantly affects how the thickness of the tabletop is perceived. Two parts of the same actual thickness can look completely different if one has a straight, calm edge and the other has a developed figured profile. The ST-001 has a thickness of 25 mm, the ST-027 has 30 mm, but the difference is determined not only by five millimeters.

ST-001 is designed for a large round surface. Its edge should not turn the table into an overloaded decorative object, especially if the underframe itself has an expressive shape. The large diameter already creates a strong geometric image. A calm edge allows the color, the shape of the circle, or the base to be the main focus.

ST-027 works differently. The compact surface is closer to the eye level of a seated person, and its edge is often clearly visible. The figured profile turns the edge into an independent decorative line. On the painted version, it is revealed by shadows; on the veneered version, it is additionally supported by the pattern and tinting.

When choosing a base, it is important not to cover the profile. If the upper part of the underframe is too wide or fits too close to the outer edge, the end may lose volume. On the other hand, an excessively small support area can create stability issues. A balance between decorativeness and structure is needed.

The profile also affects finishing. Shaped transitions require careful application of primer, enamel, varnish, or patina. A layer that is too thick can soften fine lines, while insufficient preparation will highlight defects. Therefore, it is better to entrust the ST-027 finish to a specialist who works with furniture profiles.

How to choose an underframe for ST-001

Large MDF tabletop for table ST-001 should not be installed on a random base. A diameter of 1200 mm creates a significant overhang of the edge relative to the center. If the support area is too small, the table may become unstable when leaning on the edge. If the legs are poorly positioned, users will find it uncomfortable to sit.

First, determine the type of base

For a round table, you can consider a central underframe, a frame with multiple supports, or a system of individual legs. Each option has its own advantages and limitations.

A central base frees up more space around the edges because users do not encounter legs at each seat. However, it must have sufficient support area and structural rigidity. A narrow decorative column without a calculated base does not guarantee the stability of a large tabletop.

Multiple legs can provide a wide support scheme. However, they need to be positioned so that chairs do not hit the supports. The closer the legs are to the edge, the more stable the system may be under lateral load, but the higher the risk of interference with seating. The closer they are to the center, the freer the edge, but the more careful the calculation for tipping needs to be.

In the catalog you can buy a base for a round tabletop and compare ready-made frames. Compatibility of a specific model with ST-001 must be checked against the drawing, dimensions, fastening, and calculated stability.

Check the tabletop overhang

Overhang is the distance from the support area to the edge. It affects appearance, seating, and stability. Too small an overhang makes the base look visually heavy and may interfere with legs. Too large an overhang increases leverage when load is applied to the edge.

You cannot determine the overhang just from a photo of a table you like. For ST-001, you need to consider the diameter of 1200 mm, the weight of the finished tabletop, the geometry of the base, and usage conditions. Detailed principles are covered in the material Table base for countertop: fastening, overhangs, and stability.

Save space for legs

A beautiful base can be uncomfortable if its protrusions fall into the knee or foot area. The plan should show not only the outer contour of the base but also the actual position of seated people.

Pay special attention to central carved bases with wide lower elements. They may look proportional to the tabletop but take up a lot of floor space. For a family or conference table, seating comfort is more important than decorative effect.

Check the fastening to MDF

The fasteners must match the tabletop material, thickness of 25 mm, and base design. Do not use elements that are too long, which could protrude to the surface. Also, do not assume that any screw will provide sufficient holding capacity.

The mounting scheme is determined after selecting the underframe. Some designs use mounting plates, threaded elements, or other furniture components. Suitable hardware for installing the tabletop is chosen not by name, but according to the project.

Can ST-001 be placed on four wooden legs

Technically, a large round tabletop can be part of projects with separate supports, but you cannot simply buy four legs you like and attach them at the same distance from the edge. Such a scheme requires checking stability, rigidity, and connection.

Individual legs without an apron or frame assembly can experience significant lateral loads. The table is not only used vertically: it is moved, leaned on, and the edge receives uneven load. If the connection between the leg and the tabletop is not rigid enough, the structure may become loose.

Before purchasing, you can select legs for a round table, but each model must be checked for height, top cross-section, mounting method, and design load. The category helps choose a style, not replace engineering calculation.

For a large diameter, an additional frame, apron, mounting plates, or other solution that unites the supports may be required. A universal scheme for all legs cannot be promised. The taller and thinner the support, the more carefully lateral rigidity is evaluated.

The placement is checked separately. Four legs arranged in a square create different distances to the round edge. With an unsuccessful layout, some seats will be opposite the supports. If the table is designed for free seating around the circle, a central base is sometimes more convenient. If a wide, stable contour is important, a leg system can be rational but requires proper arrangement.

How to assemble the coffee table ST-027 + STL-027

For ST-027, the SEO scheme specifies a specific related product — the carved base STL-027. This simplifies the commercial route: the buyer can consider not a random combination, but a set created for the general scenario of a coffee or side table.

Buy the base STL-027 it is worth it when a classic carved a:2:{s:4:"TEXT";s:65535:"a:2:{s:4:"TEXT";s:65534:"a:2:{s:4:"TEXT";s:67877:""

Maintain the proportions

ST-027 has a diameter of 660 mm. The base should support this scale, not extend beyond the edge, and not appear too small. The carved base becomes a noticeable part of the furniture, so its height and width affect the overall silhouette.

In the visualization, it is useful to show the table from the side. The top view does not reflect how the figured profile of the tabletop, the carving of the base, and the height of the item relate.

Check the final height

The tabletop has a thickness of 30 mm. The final height consists of the height of STL-027, the thickness of the top, and the structural mounting assembly. If there is an additional platform, plate, or gap between the parts, it also participates in the calculation.

The table should correlate with the sofa or armchair. You cannot choose the height based solely on the "coffee table" type. Upholstered furniture varies greatly in seat height and armrest height.

Align the fasteners

The fastening must not extend onto the front surface of the 30 mm thick tabletop. It must also not damage the shaped profile or veneer. The specific joint is selected according to drawing STL-027 and option ST-027.

Finish the set together

If the tabletop and base should have the same shade, it is better to consider them as a single set. Separate tinting based on different samples often leads to discrepancies. Consistency is especially important for patina: it should uniformly emphasize the profile of the tabletop and the carving of the base.

How to calculate the final table height

The basic formula is simple:

Final height = base height + tabletop thickness + structural installation gap.

For ST-001, the thickness is 25 mm, for ST-027 — 30 mm. If placed on bases of the same height and using the same mounting joint, the table with ST-027 will be 5 mm higher. In practice, the bases are designed for different types of furniture, so direct comparison is usually not necessary.

For ST-001

First, determine the desired height of the finished dining or conference table in the project. Then subtract the tabletop thickness of 25 mm and the thickness of the mounting assembly. The resulting value shows what height the base should be.

You cannot simply buy legs with a height equal to the desired table height. After adding the tabletop, the top will be higher. Also consider support pads, plates, and other elements if they are provided.

For ST-027

A coffee table is coordinated with the sofa or armchair. The height of the STL-027 underframe is added to the 30 mm thickness and the mounting assembly. If the table is to be placed next to specific upholstered furniture, it is useful to make a mockup or temporarily mark the height with a box.

Why five millimeters still matter

A difference of 5 mm does not turn one table into a tall one and another into a short one, but in precise furniture assembly it matters. If the underframe is designed for a specific thickness, replacing the model without recalculating will change the height and position of the fasteners.

Particular care is taken with sets where the tabletop must align with other furniture. For example, two adjacent tables with different tops will noticeably differ if the thickness is not taken into account.

How to secure the tabletop without accidental fasteners

The fastening is chosen after determining the material of the top and the base structure. ST-001 made of MDF and the combined ST-027 require different approaches depending on the attachment point. You cannot transfer the scheme from a solid wood tabletop to MDF without verification.

What you need to know before choosing hardware

• countertop thickness;
• material in the attachment area;
• thickness of the base mounting platform;
• number of attachment points;
• distance from fastener to edge;
• expected load;
• need to disassemble furniture;
• presence of plates, bushings, or threaded elements.

For ST-001, it is critical not to pierce the front side with a thickness of 25 mm. For ST-027, the thickness of 30 mm and the combined structure of the specific variant must be considered.

Why you can't just screw in long self-tapping screws

Too long fasteners may protrude to the surface. Too short ones may not provide the necessary fixation. An incorrect diameter can damage the material or create a weak connection.

Additionally, the fastening must distribute the load. A large tabletop experiences moments when supported at the edge. If all forces are transferred to a few small points, the joint may loosen.

When mounting plates are needed

Plates help form a predictable node between the leg or underframe and the tabletop. However, the specific plate must match the support, thread, angle, and load. In the section Buy table leg mounting various hardware options are presented, but the choice is made after determining the entire structure.

Possibility of disassembly

If the table needs to be transported, it is useful to provide a detachable joint. Repeated unscrewing of ordinary fasteners directly from MDF can reduce reliability. The project may use threaded elements or other solutions designed for reassembly.

Inspection after assembly

After installation, check stability on a level floor, absence of wobbling and deformation. The load is increased gradually, rather than testing the table with a sharp press on the edge. If the structure wobbles, the problem cannot be hidden with a leveling foot without determining the cause.

How to choose the finish coating

Tabletops are supplied as furniture blanks, so the finish plays an important role. It forms the color, emphasizes or hides the texture, and protects the surface within the intended operating conditions.

Enamel for ST-001

Opaque enamel creates a uniform surface. It suits white, black, complex colored, or contrasting tables. The color can be coordinated with the base and interior.

Before painting MDF, the end and surface require preparation. The edge and profile may absorb primer differently. Insufficient preparation leads to differences in texture or noticeable transitions.

The degree of gloss affects practicality and appearance. Gloss emphasizes shape and color but shows marks and unevenness more. A matte surface looks calmer, but specific properties depend on the coating system.

Enamel for ST-027 made of MDF

On a shaped profile, the enamel must be applied evenly. Runs or an excessive layer can soften the lines. Professional painting preserves the relief.

A colored coffee table can become a local accent. But it's better to choose the shade together with the sofa fabric, carpet, and other large surfaces, rather than from a screen.

Tinting and varnish for ST-027 with veneer

Tinting changes the shade while preserving the pattern of beech or oak. Varnish forms a protective finish. The specific system is selected based on expected use and desired appearance.

Before approving the color, a sample on the same material is needed. Oak and beech perceive the same tone differently. Even within the same species, the natural pattern can vary.

Patina

The patina emphasizes the figured profile and carving of the base. It suits classic projects but requires careful application. Too contrasting a patina can make a small table visually heavy.

If using the ST-027 + STL-027 set, it is better to coordinate the patina on both parts simultaneously.

Coating and operating conditions

Do not assume any enamel or varnish is automatically resistant to water, hot dishes, household chemicals, and scratches. Properties are determined by the specific coating system. Before ordering, inform the craftsman how the table will be used.

ST-001 and ST-027 should not be used without a suitable finish if the material and card suggest further finishing. Care should also be chosen based on the coating, not just the base.

Practical choice for different situations

Need a table for daily family dinners

The main candidate is ST-001. A diameter of 1200 mm allows for a full surface, but before purchasing, you need to check the arrangement of chairs and the underframe. If the base overlaps the leg area, a large area will not provide the expected comfort.

In the project, the enamel color, finished table height, and attachment method should be determined in advance. It is useful to consider the tabletop together with the base, rather than as an independent circle to which the underframe will be selected later.

Need a table for a meeting area

ST-001 is suitable for a round meeting format. Check how the room is used during the meeting: whether a passage behind seated people is needed, where the doors are located, whether the base interferes with chairs. If there will be equipment on the table, plan its placement and cables in a separate project, without cutting holes without coordinating the design.

Need a small table in front of the sofa

ST-027 fits the task better. The 660 mm diameter is not intended for a full meal, but is suitable for a lounge area. First measure the free rectangle in front of the sofa, then place the circle inside it. Check if there is space left when a person stands up.

If the interior is classic, consider a veneer option and STL-027. For a modern colorful interior, MDF with enamel finish will work.

Need a table next to one armchair

ST-027 can be placed beside the armchair or in front of it. In this case, height is especially important: the surface should be accessible but not interfere with the armrest. A visually compact base should support the shaped edge, not cover it.

Need a match with painted furniture

ST-001 and the MDF version of ST-027 are suitable for opaque enamel. But color matching must be checked against a sample and gloss level. If the table stands next to kitchen fronts, it does not make it a kitchen work surface; it is only about visual coordination.

Need visible wood texture

Choose ST-027 in a combined finish with beech or oak. ST-001 in the current card is made of MDF and intended for painting. If a large circle with a natural pattern is required, look at other confirmed models in the furniture tabletop catalogand not to attribute a non-existent variant to ST-001.

Need a table for a small room

Do not automatically choose ST-027 just because it is smaller. First determine the function. If a dining table is needed, a coffee table top will not solve the task. A different dining model may be required, rather than using ST-027 for the wrong purpose.

If a coffee table is specifically needed, check the 660 mm circle in the actual layout. Compact furniture can also obstruct a narrow passage.

Need an item for outdoor use

Neither ST-001 nor ST-027 can be recommended for permanent outdoor use without confirmed material and coating characteristics. Precipitation, frost, and UV create a different environment. Do not buy an interior blank expecting that any varnish will automatically make it suitable for outdoor use.

Need a countertop for a kitchen set

These models are intended for standalone tables. They are not ready-made work surfaces for a sink and hob. The difference is explained in more detail in the material how a furniture countertop differs from a kitchen countertop.

What to buy together with the tabletop

Purchasing one countertop does not complete the project. A base, fasteners, finish, and in some cases, support feet or other elements are needed. The list depends on the model.

For ST-001, first select a stable underframe or a calculated leg system. Then determine the fittings. You cannot buy fasteners in advance without knowing the thickness of the mounting platform and the connection method.

For ST-027, the most straightforward set is the tabletop and the carved underframe STL-027. The material and finish are coordinated together. If a different base is chosen, its compatibility is checked separately.

Table "What to buy together"

If the desired tabletop type is not yet determined, first select a round tabletop, then assemble the set. Purchasing the base before choosing the diameter may lead to incorrect overhang and proportions.

How to avoid confusing these tabletops with similar products

Do not confuse a furniture tabletop with a kitchen work surface

ST-001 and ST-027 are intended for standalone tables. The cards do not confirm readiness for installing a sink, hob, constant contact with water, or household chemicals. A special kitchen project requires separate approval.

Do not call ST-027 fully solid wood

The combined version uses MDF, solid wood edging, and veneer. This provides a wood-like appearance and shaped profile, but the construction does not become solid wood. Accurate description is important for customer expectations and finish selection.

Do not consider the 660 mm diameter as a small dining table

ST-027 — tabletop for a side or coffee table. It cannot be recommended for regular full dining service for several people solely due to its round shape.

Do not consider ST-001 a ready-made table

The card sells a tabletop. The base, legs, fasteners, and finish are selected separately, unless otherwise confirmed by the configuration. Before ordering, compile a complete list of parts.

Do not confuse thickness and purpose

ST-027 is 5 mm thicker, but this does not mean it is suitable for heavier loads or replaces ST-001. The purpose is determined by the entire structure and size.

Do not apply outdoor requirements to an interior model

Wood veneer or enamel alone do not confirm suitability for outdoor use. Specific data on outdoor operation is required.

Mistakes when buying a round tabletop

Mistake 1. Choosing only by photo

On the card without scale, both models look like round tabletops. The buyer may underestimate the difference between 1200 and 660 mm.

How to avoid: apply both diameters to the plan or floor with painter's tape. The difference will become obvious.

Mistake 2. Not considering the threefold difference in area

The diameter of ST-001 is less than twice as large, but the area is about 3.3 times larger. Therefore, the requirements for the room and the base differ significantly.

How to avoid: compare not only the diameter, but also the occupied area, edge overhang, and free zones.

Mistake 3. Considering ST-001 a kitchen countertop

Ranking by kitchen queries can create false expectations. The product is a furniture blank for a separate table.

How to avoid: do not plan a sink, hob, or constant contact with water without a special project.

Mistake 4. Buying ST-027 for a dining table

The compact model is intended for coffee tables. Attempting to use it as a full dining table will result in insufficient surface area.

How to avoid: first define the function, then the diameter.

Error 5. Choosing random four legs for ST-001

Beautiful supports do not guarantee the stability of a large circle.

How to avoid: check the rigidity, support contour, leg position, and connection method.

Error 6. Not accounting for legroom

The underframe may be stable but uncomfortable.

How to avoid: draw the base and chair positions on one plan.

Error 7. Not calculating the final height

The buyer takes legs of the required table height and forgets to add 25 or 30 mm for the tabletop.

How to avoid: use the formula with the top thickness and mounting assembly.

Error 8. Calling ST-027 fully wooden

The combined construction is described inaccurately, causing the buyer to expect solid wood.

How to avoid: check the base, trim, and facing separately.

Error 9. Expecting a ready-made coating

The blank is mistaken for a fully finished surface.

How to avoid: agree on enamel, tinting, varnish, or patina in advance and include the finish in the project.

Error 10. Choosing color by screen

The monitor does not show the exact shade and degree of gloss.

How to avoid: approve a real sample on the corresponding material.

Error 11. Buying fasteners before the base

The fittings do not match the mounting plate or turn out to be too long.

How to avoid: First, select the base, then calculate the node.

Error 12. Not checking the possibility of disassembly

The table is assembled with a one-time connection, and then transportation is required.

How to avoid: Report the need for reassembly before selecting fasteners.

Error 13. Ignoring passages

The circle physically fits into the room but interferes with opening doors or moving.

How to avoid: Check the furniture together with the chairs and moving elements of the room.

Error 14. Buying ST-027 for outdoor use

The interior model is considered suitable for the terrace without confirmation.

How to avoid: do not use the product outdoors without official data and a suitable covering system.

Error 15. Finish the tabletop and underframe separately

The same shade name gives different results on materials.

How to avoid: agree on a single sample and technology for the set.

Who ST-001 suits and who ST-027 suits

ST-001 will suit if

• a full dining, family, or conference table is needed;
• the room allows placing a 1200 mm circle with chairs and passage;
• a smooth opaque finish is required;
• the base can be selected and calculated separately;
• a calm modern silhouette is important;
• the buyer is ready to agree on the mounting and finish.

ST-001 will not work if

• a compact table near the sofa is needed;
• visible wood texture is required specifically within this card;
• the product is planned to be used as a ready-made kitchen work surface;
• there is no possibility to install a stable base;
• the room does not leave a free area for chairs.

ST-027 will work if

• a coffee or side table is being assembled;
• need a diameter of 660 mm;
• the shaped profile should become a noticeable detail;
• requires MDF for enamel or a version with beech or oak veneer;
• a set with a carved underframe STL-027 is planned;
• the table is placed near a sofa, armchair, in the bedroom or study.

ST-027 will not work if

• a full dining table is needed;
• a surface with a diameter of 1200 mm is required;
• permanent outdoor use is planned without confirmed characteristics;
• the buyer expects a solid wood construction;
• the selected base covers the profile or does not ensure stability.

How to buy a tabletop on STAVROS

Start with the function. If people will sit at the table to eat, work, or hold negotiations, open the card large tabletop for the dining table ST-001. If you need a low item near upholstered furniture, open tabletop 660 mm for the coffee table ST-027.

Then check the size in the room. For ST-001, place the tabletop, chairs, passage, and base on the plan. For ST-027 — the sofa, armchairs, table circle, and movement trajectories.

After that, choose the material and finish. ST-001 — MDF under an opaque finish. ST-027 — MDF under enamel or a combined version with beech or oak veneer. Current options are specified in the product card.

The fourth step is the base. For ST-001, you can select a frame for the dining table or develop a leg system with calculation. For ST-027, a commercially clear route via STL-027 is available.

Step five — fastening and height. Calculate the final height, select the mounting assembly, and ensure the fastening does not extend to the front side.

Before placing an order, compile a specification:

• tabletop article;
• size;
• the material;
• finish option;
• base article or diagram;
• final height;
• mounting hardware;
• disassembly requirement;
• color sample;
• terms of use.

If the desired model is not clearly identified, you can first study the article which tabletop to buy to assemble a beautiful table, and then return to the specific cards ST-001 and ST-027.

FAQ: questions about round tabletops ST-001 and ST-027

Which tabletop is larger — ST-001 or ST-027?

ST-001 is significantly larger. Its diameter is 1200 mm, and the diameter of ST-027 is 660 mm. The difference is 540 mm. In terms of area, the surface of ST-001 is approximately 3.3 times larger, so the models are intended for different types of furniture.

Which model to choose for a dining table?

ST-001 is intended for a full-fledged dining, family, or conference table. It has a diameter of 1200 mm and a thickness of 25 mm. Before ordering, you need to select a stable base, check the space for chairs, and calculate the final height.

Will ST-027 be suitable for a dining table?

ST-027 is primarily designed for a magazine or coffee table. Its diameter of 660 mm should not be perceived as a reduced version of a full dining tabletop. If the room is small, it is better to look for a suitable dining model rather than change the purpose of ST-027.

What is ST-027 intended for?

ST-027 is suitable for a compact table in front of a sofa, next to an armchair, in a bedroom, study, or soft meeting area. Its shaped profile makes the edge a noticeable decorative part. The model can be combined with the carved base STL-027.

What is ST-001 made of?

ST-001 is made of MDF, has dimensions 1200 × 1200 × 25 mm, and a "Prestige" sanding. It is intended for subsequent opaque finishing. Current order parameters should be checked in the product card.

What is ST-027 made of?

ST-027 is offered in MDF or a combined version. In versions with beech or oak, the structure includes an MDF base, a solid wood contour trim, and veneer on the surfaces. Therefore, such a model is correctly called combined, not fully solid.

Can I buy ST-027 with oak veneer?

The scheme confirms a combined version with solid wood and oak veneer. It is suitable for tinting, varnishing, and, with the appropriate project, patination. The availability of a specific version and current conditions should be checked in the ST-027 product card.

How does the beech version differ from the oak version?

Oak is usually chosen for a more pronounced pattern, beech for a calmer texture. The same tint shade looks different on these materials, so it's better to make a decision based on real samples.

Can ST-001 be painted white or another color?

MDF ST-001 is designed for opaque finishing, so white, black, or colored enamel is logical for this model. However, the specific color, primer, gloss level, and protective properties of the coating need to be agreed upon with the finishing contractor.

Can ST-027 be painted?

The ST-027 option made of MDF is suitable for opaque enamel. Combined options with veneer are more often chosen for tinting and transparent finish to preserve the wood grain. The finishing method depends on the chosen configuration.

Is ST-001 a kitchen countertop?

No, in the scenario under consideration, this is a furniture tabletop for a separate table. The card does not confirm readiness for installing a sink, hob, constant contact with water, or household chemicals. A special kitchen project must be agreed upon separately.

Can ST-001 be used as a table in the kitchen?

As a separate dining table in a kitchen or dining area — yes, if the base, finish, and dimensions suit the project. But this does not mean use as a built-in work surface of a kitchen set.

Is ST-027 suitable for outdoor use?

There is no confirmed data on continuous use under precipitation, frost, and UV. Therefore, ST-027 cannot be recommended as an outdoor countertop. The presence of wood or a finish coating alone does not confirm outdoor suitability.

How many people can sit at ST-001?

The exact number cannot be determined by diameter alone. It depends on the width of the chairs, the position of the legs or underframe, the required comfort, and the usage scenario. On the plan, you need to place actual chairs and check legroom.

How to know if ST-001 will fit in the room?

Draw a circle with a diameter of 1200 mm on the plan or floor. Then add chairs in both pushed-in and pulled-out positions. Check passages, door openings, and access to adjacent furniture. The table must fit not only geometrically but also functionally.

How to check the space for ST-027?

Mark a circle with a diameter of 660 mm in front of the sofa or next to the armchair. Check if you can comfortably stand up, walk, and use adjacent furniture. The shaped end should not be completely hidden by upholstered furniture.

What base is needed for ST-001?

The base must be designed for a tabletop with a diameter of 1200 mm. It is important to check stability under edge load, overhang, legroom, and the method of attachment to MDF. You can consider ready-made underframes or a custom support system, but compatibility is confirmed by the project.

Can ST-001 be installed on four legs?

Such a project is only possible after checking rigidity and stability. Four separate legs, chosen based on appearance, may not ensure a reliable structure. A frame assembly, plates, aprons, or other unification of supports is often required.

Which base is suitable for ST-027?

For ST-027, the carved underframe STL-027 can be considered. It is intended for a coffee or decorative table. Before ordering, you need to verify the material, dimensions, final height, fastening, and finish.

How to calculate the height of the finished table?

The thickness of the tabletop and the mounting gap are added to the base height. For ST-001, the thickness is 25 mm, for ST-027 — 30 mm. Support pads, plates, and other elements are also included in the calculation if they are used.

Why can't you take legs with a height equal to the finished table?

Because after installing the tabletop, the total height will increase by 25 or 30 mm plus the mounting assembly. The legs or underframe must be lower than the required final height by the amount of the top and connection.

What fasteners should be used for MDF?

There is no universal answer without knowing the base. You need to know the thickness of the mounting plate, the number of attachment points, the material in the installation area, and the need for disassembly. The fasteners must not protrude onto the front surface or damage the MDF.

Is it possible to drill holes yourself?

Drilling is only possible according to a prepared scheme. An error in depth or location can damage the face surface, veneer, or profile. If there is no drawing and experience, it is better to entrust the installation to a specialist.

Does the tabletop need finishing before installation?

The sequence depends on the project. A preliminary test assembly is often useful to check the fit and holes, and then perform the finish. But the specific technology is agreed upon with the master, because some units require a different sequence.

Can ST-001 and the underframe be made the same color?

Yes, visually they can be combined with one enamel. But MDF and wood may perceive primer and coating differently. For a match, a single sample, an agreed gloss level, and the same finishing system are needed.

Do ST-027 and STL-027 need to be finished together?

If the set should have a single shade, joint finishing is preferable. This is especially important for tinting and patina, which must work identically on the tabletop profile and base carving.

What to buy together with ST-001?

A calculated underframe or support system, suitable mounting hardware, and finishing coating will be required. The specific set is formed after the drawing. Do not buy random legs or fasteners in advance.

What to buy together with ST-027?

You can select the STL-027 underframe, mounting hardware, and an agreed finishing system. If a different base is used, its dimensions and compatibility are checked separately.

Where can I see other tabletops?

Other shapes, sizes, and materials are available in the section Buy a tabletop for a table. A broad query is best directed to the category, while a specific choice of ST-001 or ST-027 should be made based on purpose.

Which option is simpler for a modern interior?

ST-001 made of MDF with enamel finish suits a large modern table. ST-027 made of MDF with enamel finish is for a compact coffee table. The choice depends primarily on function, not on a style label.

Which option suits a classic interior?

ST-027 with beech or oak veneer and a carved base STL-027 gives a distinct classic character. ST-001 can also be used in a classic project with a suitable base, but in its current listing, it remains an MDF blank for opaque finishing.

What should be checked right before ordering?

Check the article number, size, material, selected finish, base, final height, mounting, and installation location. For ST-001, additionally verify the stability of the large circle and fit. For ST-027, ensure it matches the coffee table scenario and the visibility of the shaped profile.

Result: which round tabletop to add to the cart

ST-001 and ST-027 share a round shape, but their customer tasks are different. ST-001 with a diameter of 1200 mm and thickness of 25 mm made of MDF is intended for a full dining, family, or conference table. It is chosen when the room allows