Buy spherical furniture legs: compact MN-220 in beech or oak, or large MN-235 in MDF — which to choose

Spherical furniture legs can be purchased for tasks of completely different scales. A small rounded support can neatly lift a nightstand, pouf, or chest of drawers and add a soft line to the furniture. A large ball with a diameter of 200 or 300 mm works differently: it becomes the main decorative element, changes the proportions of the body, affects the distance between supports, shipping dimensions, and even whether the bottom drawer can be opened freely. Therefore, the external similarity of MN-220 and MN-235 does not make these models interchangeable.

MN-220 is a compact turned ball leg made of beech or oak. It is available in two sizes: 105 × 109 × 38 × 20 mm and 125 × 130 × 38 × 32 mm. Beech is suitable for opaque enamel, oak is suitable for tinting while preserving the natural grain. This round wooden furniture leg is designed for relatively small bodies: bedside tables, poufs, benches, chests of drawers, and low cabinets. It is noticeable but does not turn the base into a separate sculpture.

MN-235 is a large spherical support made of deep-milled MDF. Two sizes are confirmed: 195 × 200 × 62 mm and 295 × 300 × 80 mm. The smaller option weighs about 3 kg, the larger about 11.5 kg. The surface is prepared with one layer of primer-sealer for further painting. This designer ball leg is suitable for large tables, sofas, cabinets, chests of drawers, and custom furniture constructions where the ball should be clearly visible from a distance and define the character of the entire piece.

The buyer's choice therefore comes down not to the question 'which leg is prettier', but to four checks: whether the diameter matches the size of the body, whether the material is suitable for the desired finish, whether the furniture is designed for the weight of the supports, and whether there is space for mounting, foot cap, drawer opening, and free passage. Below is a detailed breakdown of when to order MN-220, when to choose MN-235, how to calculate the final height, how many supports are needed, how FUR-001 and FUR-012 differ, and why the query 'legs for a round table' should not be confused with round-shaped legs.

Go to Catalog

How is MN-220 different from MN-235

Both models are built on a ball shape but belong to different scale groups. MN-220 is perceived as a low furniture leg. Its diameter is close to 109 or 130 mm, so it easily fits under a small cabinet and does not take up too much space in corners. MN-235 starts with a diameter of 200 mm. Even the smaller version is almost twice as wide as the compact MN-220 and noticeably taller. The larger model with a diameter of 300 mm is comparable to a large decorative object.

The material also determines the visual result. MN-220 is made from solid beech or oak. The buyer can leave a noticeable wood texture if they choose oak with a clear or semi-transparent finish, or get an even color on beech under enamel. MN-235 is made from deep-milled MDF. Its strength lies not in the natural wood grain, but in precise large geometry and the ability to achieve a uniform opaque color.

The weight also differs. For MN-220, the exact weight is not specified in the provided diagram, so it cannot be invented. It is only known that it is relatively light compared to the large MN-235. The smaller MN-235 weighs about 3 kg, the larger one about 11.5 kg. When purchasing four large supports, the furniture gains significant additional weight even before installing the cabinet, tabletop, and contents.

What the models have in common is the "Prestige" quality finish, the ability to use FUR-001 or FUR-012 mounting systems after compatibility check, and the need to select a protective floor glide. But the floor glides differ: for MN-220, a felt FUR-027 with a diameter of 24 mm is specified, for MN-235, a round FUR-021 with a diameter of 19 mm. This is another sign that the kit of one leg cannot be mechanically transferred to another.

What is a ball furniture leg and why size changes everything

A ball leg is a support where the rounded shape becomes the main visible part. In a small size, the ball works as a soft finish for the body. It removes the feeling of a heavy rectangular block, creates a gap above the floor, and makes the furniture visually lighter. This is exactly how MN-220 works under a cabinet, pouf, or chest of drawers.

In a large size, the ball ceases to be just a leg. A diameter of 200 or 300 mm makes the MN-235 perceived as a separate volume. It can be almost comparable to the height of the bottom drawer, the thickness of a sofa base, or the depth of a compact cabinet. Therefore, the shape affects not only the style but also the furniture construction.

The larger the ball, the further its center must be moved from the edge to prevent the support from looking accidentally protruding. At the same time, too large an offset reduces the stable contour. For four supports, you need to check whether they collide with each other, block the bottom drawer, or interfere with the base, doors, or soft upholstery.

A large diameter also changes transportation. Furniture on MN-235 may not fit through a doorway or may require removing the supports before delivery. If the structure must be disassembled, the mounting is designed in advance. You cannot first glue or rigidly install the legs and then find out that the item does not fit in the elevator.

Therefore, the round support is chosen in the scale of the entire item. An isolated product photo does not show how large the ball will be relative to the body. The best way to check is to draw a circle of the actual diameter on cardboard, cut out a template, and apply it to the facade or furniture sketch.

Our factory also produces:

View Full Product Catalog

When to buy a compact ball leg MN-220

For a bedside table

A bedside table usually has limited width and depth. A ball with a diameter of 109 or 130 mm leaves enough space between the supports and does not turn the lower part of the body into a set of heavy volumes. A height of 105 or 125 mm lifts the furniture, makes the base lighter, and leaves a small gap for cleaning if it matches the design.

For a cabinet, it is important to check the opening of the lower drawer. If the front descends close to the floor, the ball should not protrude into its path. The distance from the front edge of the body to the center of the leg is calculated together with the mounting. For a compact body, you can purchase the MN-220 leg in the appropriate size, but marking is done only after obtaining the exact dimensions.

For a pouf and a bench

A pouf and a bench bear the load of a seated person, so four beautiful supports cannot simply be screwed to a thin base. The frame must distribute the force, and the fasteners must work in a durable material. MN-220 is suitable in scale for a small seat and does not take up excessive height.

Wooden legs for a pouf can be painted to match the color of the upholstery, body, or decorative trim. Beech under enamel will give a smooth opaque surface, oak under tinting will add natural texture. A floor protector will protect the floor and reduce noise when moving.

For a chest of drawers

A small and medium chest of drawers often benefits from rounded legs. The rectangular body becomes softer, and the bottom line becomes lighter. MN-220 does not draw attention away from the fronts and handles, so it is suitable for furniture with panels, milling, carved overlays, and noticeable wood.

For a wide, heavy chest of drawers, the number and placement of supports are calculated separately. Four legs may not be enough if the long bottom sags. In such a case, central support, a reinforced base, or a different structural scheme is needed. The product card of the leg does not replace the body calculation.

For a small cabinet

A low cabinet or display case on spherical supports gets a noticeable gap above the floor. MN-220 is suitable when the body is not too heavy and the supports should not dominate. For a tall cabinet, be sure to assess stability against tipping and wall attachment if required by the design.

A small round support does not compensate for a narrow and tall body. The higher the furniture, the more critical the position of the center of gravity. Before ordering, you need to check not only the downward load but also the risk of tipping when doors or drawers are open.

When natural wood is needed

MN-220 is the only model among those compared that offers a choice of beech or oak solid wood. For a transparent finish and preserving the grain, you can choose a round oak support. The texture will emphasize the turned shape and connect the legs with the wooden tabletop, fronts, or floor.

For enamel, beech is suitable. The MN-220 beech leg for enamel can be painted together with the body. When the shade matches, the ball becomes an extension of the furniture; when contrasting, it becomes a separate decorative point.

When to choose the large spherical MN-235

When the ball should be the main element

MN-235 is chosen not for inconspicuous body support. A diameter of 200 or 300 mm inevitably attracts attention. This support is suitable for simple furniture that needs a strong sculptural gesture: a smooth table, a sofa with a minimalist base, a large dresser without heavy carving, or a cabinet with large monochrome surfaces.

If the facades are already overloaded with decor, a large ball-shaped leg can create competition. In that case, it is wiser to choose a compact MN-220 or another shape. The MN-235 reveals itself best when there is free space around it and the ball is visible from the side.

For a designer cabinet

A large cabinet on two or four balls can look like an art object. But the body must be wide and deep enough. The smaller MN-235 with a diameter of 200 mm already requires a noticeable setback. The larger one with a diameter of 300 mm can take up almost the entire depth of a compact cabinet.

Before purchasing, make a front, side, and top view. Check that the support does not protrude beyond the facade, does not block the lower drawer, and does not collide with the adjacent leg. If the dimensions are suitable, you can buy the spherical leg MN-235 in diameters of 200 or 300 mm.

For a sofa

Spherical legs for a sofa can be visible from the front and sides, especially on a model with a high base. The MN-235 creates a strong image and suits large upholstered furniture. However, the weight of the sofa and dynamic load require a sturdy frame and calculated fastening.

The diameter of the ball affects the seat height. The 195 mm option raises the body by approximately 195 mm before accounting for the mounting unit and foot pad, while the 295 mm option raises it significantly higher. You cannot replace regular low legs with MN-235 without recalculating the overall seating and structure.

For a table

The MN-235 can be used in tables, but not as a standard high leg for a dining tabletop. The height of 195 or 295 mm is suitable for low, coffee, decorative, or specially designed structures. For a regular dining table, a different base scheme is required.

The balls can be placed at the corners, closer to the center, or used in smaller quantities if there is a rigid frame. Each scheme affects stability. For a heavy tabletop, the calculation of fastening and load distribution is especially important.

For a wardrobe and a large chest of drawers

A large wardrobe or chest of drawers on MN-235 gets a pronounced base. A ball with a diameter of 300 mm can be comparable to the height of the lower module. Such furniture requires a fairly spacious room, otherwise the large supports will visually and physically occupy the passage.

The weight of the four larger legs will be about 46 kg based only on approximate data for each support. This must be taken into account during transportation, floor load, and assembly. The value of about 11.5 kg refers to one support, not the set.

How the size of the ball affects furniture proportions

The minimum options show the scale difference especially clearly. MN-220 with a height of 105 mm has a width of 109 mm. MN-235 with a height of 195 mm has a diameter of 200 mm. The larger model is about 90 mm taller and almost twice as wide. This is no longer a small increase, but a transition to a different category of furniture.

The maximum options diverge even more: MN-220 — 125 × 130 mm, MN-235 — 295 × 300 mm. The larger MN-235 is about 170 mm wider. If you place four such supports under the body, each will require a large corner area. There may be little space left between the front balls, especially on a narrow cabinet or short sofa.

The proportion is not assessed by a single number. You need to compare the ball diameter with the facade width, base height, body thickness, and handle size. On a small chest of drawers, MN-235 may look heavier than the body itself. On a large sofa, MN-220, on the contrary, can get lost and be perceived as a random small detail.

A full-size template solves the problem. For MN-220, cut a circle with a diameter of 109 or 130 mm, for MN-235 — 200 or 300 mm. The template is applied to a scaled photo of the facade or directly to the body. This immediately shows how much space will remain between the balls and how far the support protrudes beyond the edge.

Which model is suitable for a bedside table and a chest of drawers

Small bedside table

For a bedside table, MN-220 is often suitable. Its height of 105 or 125 mm does not make the furniture excessively tall, and its diameter of 109 or 130 mm keeps free space in the corners. You can choose beech under enamel in the body color or oak under tinting.

MN-235 is only possible for a very large designer bedside table. Even a diameter of 200 mm needs to be checked against the depth. If the body has a depth close to the ball's size, the support will take up almost the entire side projection and may protrude beyond the front.

Medium-width chest of drawers

MN-220 is suitable for a chest of drawers where light proportions and easy cleaning are important. Four balls support the body but do not distract attention from the fronts. For a heavy and wide chest of drawers, check the bottom deflection and add a central support if necessary.

MN-235 is suitable for a large designer chest of drawers. The 200 mm option can become a noticeable base, and 300 mm can be a central part of the image. But the weight and distance between the balls require a separate drawing.

TV cabinet

A long low table experiences load along its entire length. Compact MN-220 can be distributed at the corners and supplemented with central supports if calculations require it. Large MN-235 reduce the number of possible points but can support the scale of a long body.

You cannot choose the quantity based only on appearance. Equipment, drawer contents, and the tabletop add mass. The supports must be connected to a sturdy base, not just a thin bottom.

MN-220 or MN-235 for a pouf and sofa

For a compact pouf, bench, and small chair MN-220, it is more logical in size. The ball does not raise the seat too high and does not protrude far beyond the frame. The oak version adds natural material, while the beech version allows painting the legs together with the base.

MN-235 is suitable for a large sofa or designer bench where the supports should be visible. A height of 195 or 295 mm noticeably changes the seating. If the sofa was originally designed for low legs, a simple replacement will lead to excessive seat height and a change in seating angle.

Upholstered furniture creates dynamic load: a person sits down, stands up, shifts. The fastening must resist not only vertical weight but also lateral forces. FUR-001 or FUR-012 are considered only after checking the frame, base thickness, and mounting node.

The floor under the sofa is often sensitive to pressure and movement. For MN-220, a felt glider FUR-027 is provided, for MN-235 — FUR-021. But the glider does not turn a heavy sofa into furniture that can be moved constantly without risk. The mass of a large support requires careful handling.

Can spherical supports be used for a table

The phrase "table support balls" can mean different designs. MN-220 has a height of 105 or 125 mm, so it is not suitable as an independent leg for a standard dining table. It can be used in a low coffee table, podium, base, or other specially designed item.

MN-235 with a height of 195 or 295 mm is also not a regular high table leg. It is suitable for low decorative tables, large coffee tables, or custom bases where the height is achieved by other elements. The final structure must be calculated as a whole.

The spherical shape can work under a round tabletop, but the query "legs for a round table" primarily refers to the shape of the tabletop, not the legs. Compatibility is determined by the tabletop diameter, height, number of supports, and stability. MN-220 cannot be promoted as universal legs for a round dining table just because of the word "round."

Under a heavy round tabletop, four balls at the edges may reduce legroom. The central scheme requires a rigid frame. Before purchasing, create a top view and check the stable contour, overhangs, and fastenings.

Furniture legs 20 cm: which model is closer

Customers often look for furniture legs 20 cm high. MN-220 does not match this size: its height is 105 or 125 mm. The closest option is MN-235 with a height of 195 mm. But 195 mm is not exactly 200 mm, so the size cannot be rounded in the drawing.

The final height includes the foot pad and any possible mounting assembly. If the cabinet must be raised exactly to a certain distance, the entire system is measured after assembly. The phrase "about 20 cm" is suitable for preliminary selection, but not for production.

The second size of MN-235 has a height of 295 mm, which is closer to 30 cm. It is significantly larger and heavier. It cannot be chosen as a "slightly taller version" without re-checking the cabinet.

Beech, oak, or MDF: how material changes the choice

MN-220 made of beech for enamel coating

Beech is suitable for a customer who needs a smooth, opaque finish. On a small spherical leg, enamel emphasizes the shape but hides the natural grain. This is convenient when the supports must match the painted cabinet of a nightstand, dresser, pouf, or bench. White enamel makes the leg lighter, dark enamel enhances contrast with the floor, and colored enamel ties the furniture to the interior palette.

Even with the same color code, the result on beech and on an MDF facade may differ due to primer, absorption, and gloss level. Therefore, it is better to paint the legs and the cabinet in the same system or compare samples in advance. On a set of four supports, the difference in shades is especially noticeable because the legs are at the same level and illuminated equally.

Beech is also convenient when repairing finished furniture. If the facade is already painted, the craftsman can select enamel based on a sample. But matching from a catalog does not guarantee a match after drying. It is necessary to consider the aging of the existing coating and the lighting in the room.

MN-220 made of oak for tinting

Oak is chosen for its natural grain. Stain, oil, varnish, or another compatible system allows darkening or lightening the wood without covering the fibers. On a spherical shape, the grain rotates relative to the light, making the surface look lively and three-dimensional.

Oak MN-220 pairs well with a wooden tabletop, mirror frame, handles, overlays, and flooring. However, it is not necessary to achieve a perfect match of every grain. It is important that the supports and adjacent elements are in the same color temperature and have a consistent sheen.

If the body is made of painted MDF, oak legs can be the only natural material in the piece. This contrast is especially expressive on white, gray, or deep-colored furniture. But before ordering, you need to decide whether all four supports will be in the same tone. Tinting is done as a set, not one leg at a time on different days.

MN-235 made of MDF for opaque painting

Deep-milled MDF allows for a large ball with a diameter of 200 or 300 mm with controlled geometry. In this model, the material is chosen not to showcase the wood grain, but to create a large volume for enamel coating. One layer of insulating primer prepares the surface but is not a finished decorative coating.

Before painting MN-235, inspect it in the light, check the sanding, joints, and areas around the mounting node. The finishing system must be compatible with MDF and the insulating primer. If the ball is painted in a rich glossy color, even small defects become more noticeable than on a matte surface.

The large surface area of MN-235 requires careful application technique. On a sphere, it is easy to get an uneven layer, a run, or a difference in sheen. It is convenient to paint the support on a fixture that allows you to rotate it without touching the finished surface. The weight of the larger model, about 11.5 kg, complicates this work, so the method of hanging and moving is planned in advance.

Why you cannot choose a material based solely on the word "wood"

The query "round wooden furniture legs" fits MN-220 well because the model is indeed made of beech or oak. MN-235 is a large spherical furniture support but is made of MDF. Calling it wooden in the narrow sense of solid wood is not accurate. It is important for the buyer to see this difference before placing an order.

If the project requires a transparent finish, natural oak grain, and the tactile feel of solid wood, MN-220 is better suited for the task. If a 300 mm diameter ball under a smooth black or white enamel is needed, MN-235 provides the required scale. The correct material follows the shape and finish, not an abstract notion of prestige.

How to calculate the final height of furniture

The leg height is not always the exact amount the body is raised off the floor. A foot pad, mounting plate, underlayment, and structural gap may be added to it. Conversely, part of the fastening assembly goes inside the body and does not increase the overall height. Therefore, the drawing specifies not only the support size but also the complete cross-section of the connection.

MN-220 raises furniture by 105 or 125 mm before accounting for additional parts. For a bedside table, this affects the position of the top surface relative to the mattress. If the old cabinet already had a base, removing it and installing the balls may change the height more than the buyer expects.

MN-235 raises the cabinet by 195 or 295 mm. In a sofa, such a difference can completely change the seating. In a dresser, it can raise handles and the tabletop too high. In a coffee table, it can turn a low item into an uncomfortably tall one. Therefore, the large model is chosen only after calculating the finished furniture.

For testing, temporary supports are used. Blocks of the required height are placed under the cabinet, and the furniture is evaluated in the room. It is important to look not only from the front, but also while sitting, walking past, opening drawers, and comparing with adjacent items.

Final table height

A bedside table is usually comfortable when the top surface is related to the mattress level. Too low forces reaching down, too high blocks the bed and may interfere with the lamp. MN-220 provides two close but noticeably different levels. A difference of 20 mm can be important in a finished bedroom.

MN-235 with a height of 195 mm can raise the cabinet by almost 20 cm. This is only suitable for a table initially designed lower than usual or intended for a large decorative gap. The larger model of 295 mm requires an even deeper reconsideration of proportions.

Final height of pouf and bench

The seat height consists of the leg, frame, base, and soft filling. Even the compact MN-220 can make a finished pouf too tall if the frame is already designed for other supports. Before ordering, measure the thickness of all layers.

MN-235 is only suitable for specially designed upholstered furniture. A 295 mm ball under a regular pouf will raise the seat almost to the height of a low stool before adding the frame. Such a scheme may be artistically interesting, but must be ergonomically verified.

Final coffee table height

The coffee table is compared to the sofa and armchairs. MN-220 is suitable for a low table if the tabletop and frame add the required height. MN-235 195 mm allows for a more noticeable clearance, while 295 mm creates a medium-height table. Accurate conclusions are drawn only based on the complete structure.

How to check the distance between large spheres

For a rectangular body, first set an indentation from the edges. The center of the sphere should not be too close to the facade to ensure sufficient material area for the fastener and to prevent the support from appearing protruding outward. Then calculate the free gap between the spheres in width and depth.

With a body width of 800 mm and two front MN-235 spheres with a diameter of 300 mm, after subtracting the diameters, only 200 mm remains before accounting for indentations. If you indent 50 mm from each edge, the free gap between the spheres will be about 100 mm. Such furniture will be perceived as an almost solid base of spheres.

For the MN-220 of the same body, the situation is different. Two spheres with a diameter of 130 mm occupy 260 mm, leaving significantly more free space. That is why the compact model is better suited for standard cabinets and chests of drawers.

In terms of depth, the trajectory of the lower drawers is especially important. Some facades have an overlay handle that protrudes below the body. When opening, it may approach the sphere. In upholstered furniture, the overhang of the upholstery and decorative trim are taken into account.

Distance to the baseboard

If the furniture retains a central baseboard or lower frame, the sphere should not cut into it. MN-235 may require changing the width of the baseboard or completely removing it. MN-220 more often fits next to the existing structure, but also requires verification.

Distance to the wall and baseboard

The rear support should not press against the baseboard and push the body away from the wall. For a sphere with a diameter of 300 mm, the center may be far from the rear edge, which reduces the stable contour. It is better to draw a floor plan including the baseboard in advance.

Distance to adjacent furniture

The large MN-235 protrudes into the passage and visually expands the object. If there is a bed, sofa, or wardrobe nearby, the ball can interfere with cleaning and movement. Leave not only a technical gap but also an operational gap.

How many spherical legs to buy

Four supports is a common scheme, but not a universal answer. A small cabinet or pouf often uses four MN-220. A long chest of drawers may require an additional central leg if the bottom lacks sufficient rigidity. The quantity is determined not by the shape of the ball, but by the construction of the body.

MN-235 is sometimes used in quantities of two, three, or four. Two large spheres can support a console only with a rigid connection to the wall or a hidden frame. Three supports provide geometric stability on uneven floors, but their placement must prevent tipping. Four require a large body.

If part of the load is taken by a hidden frame, there may be fewer decorative balls. This is especially useful for a sofa: external MN-235 create an image, while additional invisible supports support the long frame. This solution requires professional design.

Ordering one leg for replacement later is risky if precise finishing is needed. Batches of wood and paint may differ. For a new item, it is better to buy a full set at once and process it together.

FUR-001 or FUR-012 — which mount to choose

Buy a set of FUR-001 is possible as a connection option with a self-tapping stud M8 × 60 and a metal insert M8 × 13. The set is listed among the necessary fittings for both models. It allows creating a threaded connection but must work in sufficiently strong material.

If the bushing is installed in a thin bottom made of weak board without reinforcement, the load can tear out a section of material. For a cabinet, pouf, or chest of drawers, a wooden insert, frame, or thickened area is often required. The size and position of the reinforcement are determined by the craftsman.

Buy mounting plate FUR-012 It can be used for a scheme where the fastening is distributed over a larger area. The plate facilitates dismountable installation, but its screws must also enter strong material. On a thin board, they can tear out along with the surface layer.

MN-235 creates increased requirements for the assembly due to its own weight and large diameter. When moving furniture, the joint acts as a long lever. The fastening must resist rotation, tilt, and impact. A single stud without structural orientation fixation may be insufficient.

When FUR-001 is more convenient

The threaded kit is convenient if there is a strong insert in the body and the leg needs to be removed for transportation. It allows you to neatly connect the support without a visible plate. But the exact hole diameter, depth, and tightening torque must match the hardware.

When FUR-012 is more convenient

The mounting plate is convenient for a body where several screws can be fastened over an area. It also helps to replace the leg without repeated intervention in the material. However, the plate's protrusion and dimensions must be accounted for in the fit.

Why a universal answer cannot be given

The same FUR-001 can work in a massive frame and be unreliable in thin MDF. FUR-012 may suit a cabinet but not fit under a narrow pouf frame. The choice depends on the furniture, not just the leg article.

How to select a foot pad for MN-220 and MN-235

For the compact MN-220, the required hardware is specified as a felt glider for MN-220 FUR-027 with a diameter of 24 mm. It creates a soft contact point, helps protect parquet, laminate, or other sensitive flooring, and reduces noise when carefully moving small furniture.

For the large MN-235, the specified item is a round glider for MN-235 FUR-021 with a diameter of 19 mm. It cannot be automatically replaced with FUR-027 just because the felt pad seems larger. The mounting position and bottom point design differ between models.

The glider does not solve the problem of uneven floors if the difference is significant. A small pad can eliminate minor noise or protect the surface, but should not be used as a random wedge for leveling. If furniture wobbles, check the body geometry and the length of all supports.

For the heavy MN-235, the load-bearing capacity of the flooring is important. Soft material can be compressed under a small contact point. If the furniture is placed on carpet, cork, or soft vinyl, the behavior of the base must be checked separately.

What to buy together with furniture legs

A complete set starts with the selected supports, but does not end with them. The buyer will need fasteners, gliders, finishing materials, and possibly body reinforcement. If the legs are mounted on old furniture, additionally assess the condition of the bottom and old holes. A damaged mounting area cannot be used without repair.

Broad queries like "buy furniture legs" and "choose round legs for furniture" are best covered by a category. In the section, you can buy legs for custom finishing, compare spherical, turned and other shapes. For chests, cabinets and nightstands, a separate selection is available, where it is convenient to select the height of supports for the body.

How not to confuse a ball leg with similar products

Round leg and leg for a round table

A round leg describes the shape of the support itself. A leg for a round table describes the purpose for a tabletop of a specific shape. MN-220 is indeed a round wooden leg, but its height of 105–125 mm is not suitable for a standard dining table. MN-235 also requires a low or specially designed structure.

Therefore, the phrase "legs for a round table" cannot be used as the main commercial query for this article. A buyer may be looking for a tall base for a dining tabletop, but get a low ball leg. It is important to honestly differentiate these tasks in the article.

Spherical furniture support and decorative ball

A decorative ball can be used on a staircase, rack, bed, or in interior decor and does not have to be load-bearing. MN-220 and MN-235 are intended as furniture supports and have confirmed accompanying hardware. They cannot be replaced by a random blank of the same diameter.

It is especially dangerous to use a decorative ball under a sofa or heavy chest of drawers. The absence of a mounting node and calculation can lead to joint failure. The shape itself does not make a part a leg.

Leg and ready-made underframe

A single leg transfers load at one point. An underframe connects several supports with a frame and distributes the force. For a low table, MN-235 can be part of the base, but the buyer will still need a rigid frame or another system.

If it is not possible to design the body and fasteners, a ready-made base may be more rational. MN-220 and MN-235 are chosen when custom furniture is needed and the craftsman controls the construction.

Wooden and MDF support

MN-220 made of wood is suitable for transparent finishes and enamel. MN-235 made of MDF is intended for opaque coating. You should not buy a large model expecting to get a natural oak pattern. Conversely, there is no point in choosing an oak MN-220 if the entire set must be completely uniform under glossy enamel and natural texture is not needed.

Practical selection for specific situations

Need to update an old nightstand

Remove the existing supports and measure the bottom thickness. Check old holes, cracks, and the condition of the corners. For a regular bedside table, MN-220 is usually suitable. Compare the height of 105 and 125 mm with the mattress level and ensure the bottom drawer opens.

MN-235 is only suitable for a large body that can be reinforced. Before ordering, make a cardboard circle with a diameter of 200 mm. If it covers most of the facade, the model is too large.

Need to make a designer dresser

Determine the role of the legs. If the facades already have complex milling, handles, and decor, MN-220 will maintain balance. If the body is smooth and simple, MN-235 can become the main visual motif.

For the larger MN-235, calculate the additional weight of the set. Four supports weigh about 46 kg. The body must withstand not only static load but also moving the furniture.

Need to assemble a pouf with your own hands

The ready-made MN-220 eliminates the need to turn four identical balls. The buyer only needs to build a sturdy frame, choose the mounting, and perform the finishing. It is better to install the legs after upholstery, unless the technology requires the opposite order, to avoid damaging the coating.

The MN-235 is too large for a regular pouf. It is suitable for a designer bench with a pre-calculated seating position. First, check the seat height, then choose the support.

Need to design a sofa

For a small sofa or armchair, the MN-220 can provide a soft, rounded detail. For a large sofa, the MN-235 creates a sculptural look. The fasteners must go into the structural frame, not just the decorative upholstery.

If the sofa is planned to be moved, a detachable connection is more convenient. But the heavy MN-235 requires safe removal and storage. Do not lean the sofa on one side during disassembly without support.

Need natural oak finish

Choose the MN-220 in oak and perform a stain test. Compare the sample with the countertop, facades, and floor in both daylight and artificial light. Do not order the color based only on a photo.

Need a large black ball

The MN-235 in MDF matches the task in scale and preparation for enamel. The black color enhances the visual mass, so a diameter of 300 mm will look even larger. For small furniture, it is better to consider 200 mm or another model.

Need a support about 20 cm

The closest option is MN-235 with a height of 195 mm. The technical documentation must specify exactly 195 mm. Additionally, the thrust bearing and mounting are taken into account.

You need to install legs for a round coffee table

First, determine the height of the finished table. MN-220 is suitable for very low structures, MN-235 for taller and more sculptural ones. Then calculate the number and position of supports so that the table does not tip over when loaded on the edge.

Spherical supports in different interiors

Modern minimalism

MN-235 works well with smooth facades, simple tabletops, and solid surfaces. The large ball replaces additional decor. White enamel makes the volume calmer, black creates a graphic contrast, and a bright color turns furniture into an art object.

MN-220 suits minimalism if the leg is painted in the color of the body and almost blends with it. The shape is read through light and shadow, without creating a sharp contrast.

Modern Classic

MN-220 made of oak or beech supports frame facades, rounded handles, and soft lines. Tinted oak adds naturalness, white enamel connects the legs with moldings and doors.

MN-235 is possible as a modern interpretation of the classic ball under a large chest of drawers. To prevent the furniture from looking overloaded, the facades are made calmer.

Eclecticism

Eclecticism allows combining the traditional ball shape with an unexpected color. MN-235 in bright enamel under a simple body becomes the central element. MN-220 made of oak can connect a modern cabinet with vintage details.

Living room

In the living room, MN-220 is suitable for a small pouf, cabinet, and chest of drawers. MN-235 is for a coffee table, long cabinet, sofa, or wardrobe. It is important that there is enough free space around the large ball.

Bedroom

MN-220 naturally looks on a bedside table and a bench. Its height easily correlates with the bed. MN-235 is suitable for a large console or dresser, but may be too massive in a small bedroom.

Children's room

A rounded shape looks softer than an angular one, but furniture safety depends on stability and wall anchoring. A tall cabinet or dresser on legs should not tip over when drawers are open. The coating is chosen according to the specific project requirements.

Showroom, salon, and commercial interior

MN-235 is noticeable from afar and helps create a memorable item for a display window or waiting area. Before a serial order, a prototype is made and tested for load, painting, transportation, and cleaning.

MN-220 is suitable for repeating nightstands, poufs, and benches. The compact shape fits more easily into a limited passage and does not obstruct visitor movement.

Preparation for finishing and installation

After receiving the support, unpack and compare the set. Check dimensions, surface, mounting points, and compliance with the selected material. Do not start painting one leg until the others are inspected: the difference will be discovered too late.

MN-220 made of oak requires a test sample before tinting. It is better to use wood of the same species and preparation. Beech under enamel is primed and painted according to an agreed system. Mounting holes are protected from excess layers.

MN-235 already has a primer-insulator, but the surface is still prepared for the final coating according to the technology. A large sphere is conveniently placed on a rotating fixture. The senior model is moved considering a weight of about 11.5 kg, not holding it by the weak edges of the mounting point.

Marking of fasteners is done according to a template. The centers of all legs must be at the same offsets. For MN-235, a slight displacement is especially noticeable because the large ball extends beyond the edge of the body.

After assembly, place the furniture on a level floor and check every point. If the body wobbles, first look for a geometry error. Do not compensate for it with random layers of felt.

Care for painted and tinted supports

Care depends on the finish coating. Wipe enamel with a soft, slightly damp cloth without abrasives. Maintain tinted oak according to the recommendations of the chosen oil or varnish system. Do not transfer the rules of one finish to another.

The large MN-235 is located close to the floor and collects more dust on the lower hemisphere. When cleaning, be careful not to hit the ball with the vacuum cleaner nozzle. Glossy enamel is especially sensitive to scratches.

The felt glider FUR-027 is periodically checked and cleaned. Sand stuck in the felt can scratch the floor. FUR-021 is also inspected for wear and secure fit.

Furniture on MN-235 is better lifted rather than dragged. If the item is heavy, move it with several people or disassemble it according to the design.

Common mistakes when buying ball feet

Choosing only by photo

On a white background, MN-235 can look almost like a regular furniture foot. Without a person, cabinet, or ruler, it is impossible to perceive the 300 mm diameter. A full-size template is mandatory for the large model and useful for MN-220.

Considering models interchangeable

MN-220 and MN-235 differ not only in size. They have different materials, weight, gliders, and finish logic. Simply replacing one model with another changes the height, width, and load on the body.

Installing MN-235 under a too-small cabinet

A diameter of 200 or 300 mm can cover most of the facade, reduce the distance between the balls, and interfere with the drawer. First, check the front and top views.

Placing MN-220 under a massive sofa without calculation

A compact leg may match the style, but the mounting and number of supports must handle dynamic load. Do not rely solely on the shape and material of the array.

Confusing 195 mm and 200 mm

MN-235 is close to the request for "furniture legs 20 cm", but has a height of 195 mm. For a drawing, these are different values. Adding a foot cap and fasteners also affects the result.

Choosing MN-220 as a leg for a standard round table

A round support shape does not mean a suitable height. MN-220 is designed for low furniture. A dining table requires a different base.

Not accounting for the weight of MN-235

One senior support weighs about 11.5 kg. A set of four weighs about 46 kg. This changes transportation, floor load, and furniture behavior when moving.

Buy MN-235 for transparent tinting

MDF does not provide a natural oak grain. For transparent finishing, choose MN-220 made of oak.

Consider primer-isolator as a finished coating

MN-235 requires a finishing enamel or another compatible opaque system. The primer protects and prepares the surface but does not complete the finish.

Confuse the foot pads

For MN-220, FUR-027 is specified; for MN-235, FUR-021. Do not swap them without checking the fit.

Buy a mount without body reinforcement

Even a suitable stud or plate will not hold in a thin, weak bottom. The load must be transferred to the frame or embedded part.

Do not check the bottom drawer

A large sphere may end up in the path of the facade or handle. The error will only be discovered after assembly if a dry mock-up is not made.

Do not account for the baseboard

The back leg may press against the baseboard and push the furniture away from the wall. This is especially noticeable on the MN-235 with a diameter of 300 mm.

Not planning the delivery

Furniture with large balls becomes wider and heavier. If the legs cannot be removed, the item may not fit through a doorway or elevator.

Painting the set one piece at a time

The shade and gloss may differ. It is better to prepare and paint all supports in one batch.

Who the MN-220 is suitable for and who the MN-235 is suitable for

MN-220 will not suit a project requiring a ball with a diameter of 200–300 mm and a strong sculptural effect. MN-235 is not suitable for small furniture, transparent finishes with natural patterns, or a body not designed for heavy weight. Both models require thoughtful mounting and final finishing.

What not to do from scratch if you have ready-made STAVROS supports

The precise spherical shape seems simple only in a photo. To make four identical wooden legs yourself, you will need lathe equipment, a template, precise calibration, and uniform sanding. MN-220 removes this production task and allows you to focus on the body, finishing, and fasteners.

A large MDF ball with a diameter of 300 mm is even more difficult to make without special technology. You need to assemble the blank, perform deep milling, level the surface, and insulate the MDF for painting. MN-235 comes already formed and prepared with a primer-insulator.

The finished support does not eliminate the engineering part. The buyer still needs to calculate the body, reinforcement, quantity, and installation. But the complex decorative shape is already solved. This reduces the risk that the four balls will differ in diameter or profile.

The commercial route looks like this: choose MN-220 or MN-235, check the scale with a template, determine the FUR-001 or FUR-012 mount, add the corresponding thrust bearing, agree on the finish, and only then start assembly.

How to buy MN-220 and MN-235 at STAVROS

For compact furniture, open the card and buy round furniture legs MN-220 can be done after selecting a height of 105 or 125 mm, beech or oak. Don't forget to compare the size of 109 or 130 mm with the body depth.

For a large designer item, open large furniture ball leg MN-235. Compare diameters 200 and 300 mm, weight about 3 and 11.5 kg, height 195 and 295 mm. The larger option cannot be chosen without a drawing and transport check.

Then select the fasteners. FUR-001 or FUR-012 must match the mounting node. For MN-220 add FUR-027, for MN-235 add FUR-021. Check the current parameters in the hardware cards before ordering.

If the spherical shape fits but the size does not, open catalog of unpainted furniture legs. For case furniture, you can separately choose supports for the chest of drawers and compare narrower or taller models.

For complex structures, it is better to discuss compatibility in advance with a STAVROS manager and a furniture maker. The card confirms the product parameters, and the manufacturer is responsible for the structural design of the finished furniture.

FAQ: questions about MN-220 and MN-235

How is MN-220 different from MN-235?

MN-220 is a compact wooden leg 105 or 125 mm high made of beech or oak. MN-235 is a large MDF support 195 or 295 mm high and 200 or 300 mm in diameter.

Which leg is suitable for a bedside table?

Usually MN-220. It is more compact, fits more easily under a small body, and does not overload the facade. MN-235 is only suitable for a large designer table.

Can I put MN-235 under a small dresser?

Only after checking the dimensions. A diameter of 200 or 300 mm may take up almost the entire depth, reduce the distance between the balls, and interfere with the drawers.

What material is MN-220 made of?

Beech or oak. Beech is chosen for enamel, oak for tinting while preserving the natural grain.

What material is MN-235 made of?

Deep-milled MDF. The support has one layer of primer-insulator and requires a final opaque finish.

What sizes are available for MN-220?

105 × 109 × 38 × 20 mm and 125 × 130 × 38 × 32 mm.

What sizes are available for MN-235?

195 × 200 × 62 mm and 295 × 300 × 80 mm.

How much does MN-235 weigh?

The junior version weighs about 3 kg, the senior version about 11.5 kg per support.

Is MN-220 suitable for a pouf?

Yes, in terms of scale it fits a compact pouf or bench. The frame and mounting must be designed for the load of a seated person.

Is MN-235 suitable for a sofa?

Yes, for a large designer sofa after calculating the frame, seat height, and mounting. The support can be supplemented with hidden load-bearing points.

Is MN-235 suitable for a table?

It is suitable for a low coffee table or a specially designed designer table. For a standard dining table, a height of 195–295 mm is insufficient.

Can MN-220 be used for a round table?

The shape of the tabletop is not the deciding factor. MN-220 is too low for a regular dining table but can be used in a low coffee table.

Which model is closest to a 20 cm high leg?

MN-235 is 195 mm high. This is the closest option, but the drawing must specify the exact 195 mm, not the rounded 200.

Can MN-235 be tinted to look like oak?

MN-235 is made of MDF and is designed for opaque finishing. For a natural oak grain, choose MN-220 made of oak.

Can MN-220 be painted white?

Yes. For this, choose the beech version for enamel and coordinate the coating system with the furniture body.

Does MN-235 require a final finish?

Yes. The primer-sealer is a preparatory layer, not a finished decorative enamel.

Which mounting is suitable for MN-220?

The product card lists FUR-001 and FUR-012 as options. The specific joint is checked based on the thickness and material of the body.

Which mount fits MN-235?

FUR-001 and FUR-012 are also considered. For a heavy support, bottom reinforcement and rotation protection are especially important.

Which foot pad is needed for MN-220?

Felt FUR-027 with a diameter of 24 mm.

Which foot pad is needed for MN-235?

Round FUR-021 with a diameter of 19 mm.

How many legs are needed for a dresser?

Four are often used, but a long heavy dresser may require central supports or a reinforced base. The quantity is determined by the design.

How to check if MN-235 is too large?

Make a full-size circle with a diameter of 200 or 300 mm and apply it to the facade. Check the depth, distance between balls, drawers, and baseboard.

Can MN-220 and MN-235 be combined in one interior?

Yes, on different items they can be connected by a common shape or color. Mixing models under one body without a special project is not recommended.

What should be checked before ordering?

Size, material, quantity, weight, finish, fastening, base plate, indents, height of the finished furniture, and transportability.

Result: MN-220 or MN-235

MN-220 and MN-235 are united by a spherical shape but differ in scale. MN-220 is a compact turned leg 105 or 125 mm high made of beech or oak. It suits a cabinet, pouf, bench, small chest of drawers, and cupboard where the support should soften the body but not become the main object.

MN-235 is a large spherical support made of MDF, 195 or 295 mm high and 200 or 300 mm in diameter. It weighs about 3 or 11.5 kg and is intended for furniture where the ball shapes the entire image: a designer table, sofa, wardrobe, or large chest of drawers.

Choose MN-220 when natural oak, beech under enamel, compactness, and light proportions are important. Choose MN-235 when a large sculptural volume under a smooth opaque finish is needed. Before ordering, be sure to check the diameter, height, weight, distance between supports, fastening, and base plate.

On the STAVROS website, you can open both cards, compare confirmed dimensions, and assemble a set with FUR-001, FUR-012, FUR-027, or FUR-021. This approach helps you buy not just round furniture legs, but a specific model that matches the body scale, finish material, and actual construction.