Open the drawer without hitting the door: wooden handles Taurus HL-060-1M for corner kitchens

For a corner kitchen, handles are better chosen before drilling the facades, starting with the tightest pair — the adjacent door and drawer. The Taurus HL-060-1M has two length options, 245 and 309 mm, but switching to the shorter version does not by itself reduce parameter C. Therefore, the decision "let's take a smaller one so nothing gets in the way" should first be checked on the project.

Let's imagine a new L-shaped kitchen: the cabinets and facades are selected, but there are no holes for handles yet. The buyer likes the combination of wood and metal. The task is to preserve this idea without getting a drawer that only opens after several manipulations with the adjacent door. We start with the corner spot, agree on the length and position of the Taurus, then transfer the solution to the entire set and calculate the order. This is a hypothetical project, not a description of a completed object.

Furniture handle Taurus HL-060-1M

from 45.62 $

Go to Catalog

Wooden handle Taurus HL-060-1M: which configuration to add to the order

Taurus HL-060-1M is a wooden furniture pull handle with a coating. The STAVROS product page lists the following sizes:

Wood options available: walnut, zebrano, wenge, rosewood, and metal parts in brass or stainless steel. To compare length and cost, one combination is selected below: walnut / stainless steel. This way, the price difference is not mixed with the material difference.

Before buy wooden handle Taurus HL-060-1M, write down the full specification. For example: HL-060-1M / 245 × 15 × 37 × 160 mm / walnut / stainless steel. Quantity is added after checking the facades; writing "Taurus large" is insufficient for an order.

The dimension table does not replace the installation drawing. D values here are kept as card parameters: drilling based on them is not assigned without a confirmed diagram. The supplier must be consulted about the location of fasteners, the actual protrusion of the installed handle, completeness, and facade requirements. The finger clearance also cannot be obtained by simply subtracting B from C.

Watch video ...

Taurus 245 or 309 mm: when a short handle helps, and when it changes nothing

Adjacent facades may have different causes of collision. Sometimes the end of a long pull interferes: it ends up too close to the perpendicular door. In another case, the handle gets in its path due to protruding in front of the facade surface. Shortening may help in the first situation and change nothing in the second.

Our factory also produces:

Wooden Cap L-066

from 131.20 $

Wooden Cap L-022

from 16.66 $

Wooden Handrail L-082

from 34.64 $

Wooden Baluster L-045

from 60.47 $

Wooden baluster L-038

from 60.95 $

Wooden baluster L-047

from 65.66 $

Wooden Baluster L-050

from 61.07 $

Wooden Plate KU-001

from 11.71 $

View Full Product Catalog

What happens to the ends of the handle

Consider a conditional facade 400 mm wide. The handle is positioned horizontally, with the center of its outer dimension aligned with the center of the facade. Then the free space from the facade edge to the handle end is:

For 309 mm: (400 − 309) ÷ 2 = 45.5 mm.

For 245 mm: (400 − 245) ÷ 2 = 77.5 mm.

The difference in total length is 64 mm, but with an unchanged center, each end recedes inward by only 32 mm. This is a calculation of position in one plane, not a recommended setback for a corner kitchen, nor confirmation of unobstructed opening.

For comparison, draw both outlines on one layout, keeping the common axis. Note which end ends up near the problem area. If both length and handle position change simultaneously in two drawings, the result cannot be attributed solely to choosing the shorter version.

With another alignment method, a different effect results. If the position of the end closest to the corner is preserved, it will not move away from the obstacle at all: the entire 64 mm difference will fall on the opposite side. Therefore, the statement "place the short one in the same spot" requires clarification — whether the center of the overall dimension, the edge, or an agreed mounting reference is preserved.

Why the protrusion is checked separately

Both versions have B = 15 mm and C = 37 mm. Length A decreases, but not C. If the conflict is related to the protruding part of the handle, purchasing the 245 mm version without changing other conditions does not prove the obstruction is eliminated.

Moreover, C cannot automatically be declared the minimum width of the corner filler. In the project, installed handles, facades, their overlap, and the movement of the selected hardware interact. An actual outline of the assembly is needed, not a single number from the catalog.

When the problem is really related to length, you can compare versions and buy furniture pull handles for a verified layout. When the protrusion interferes, first change the solution, not just the size line in the cart.

Corner kitchen in motion: four checks of adjacent facades

For verification, a top view and a vertical unfolded view are needed. On the kitchen plan, label the specific door, e.g., D-1, and the adjacent drawer, Ya-1. Show the hinge side of the door, the direction of drawer extension, the position of the filler strip, and the outlines of both handles. Numbering will allow discussing one unit without confusion between the "right cabinet" and the "cabinet on the right in the drawing."

The furniture manufacturer is provided with hinge and guide models, dimensions and thickness of fronts, their overlay on cabinets, mounting gaps, and handle references. Overlay is the position of the front relative to the cabinet; it cannot be replaced by the overall cabinet width. If hardware is not yet selected, the check remains preliminary: movement is not yet fully defined.

For measurements, choose clear references: the finished edge of a specific front and a common level by height. Label what each distance refers to—the end of the handle, the center of the outer dimension, or the mounting point. The dimension from the cabinet edge and the dimension from the edge of an overlay door are not interchangeable. If the mounting coordinate is not yet confirmed, leave it blank, separately preserving the desired handle position.

One version of the diagram must use consistent data. You cannot evaluate a new thick door against an old unfolded view of a thin front, or check a handle with a filler strip that was later decided to be removed. It is useful to record the diagram date and a list of changes after which the check will need to be repeated.

Both fronts are closed

First, the initial geometry is fixed. Are both handles fully visible, do they not touch the adjacent front, is there enough space for a normal grip? The position is evaluated relative to finished face surfaces, not just boxes without doors.

Then the unit is examined in height. Two contours may intersect in the top view but be at different levels. This is a reason to check the 3D model, not to immediately reject the option. The opposite error is also possible: the handles themselves are spaced apart in height, but one of them falls into the solid surface of the adjacent door.

For a hypothetical example, imagine a horizontal pull on the upper drawer opposite a vertical handle on the adjacent door. Spacing their centers apart in height is not enough: a long vertical handle may still occupy the level of the horizontal one. The nearest sections of the full contours are checked. If the handles have indeed separated, the next object of comparison remains the adjacent facade itself, which is significantly taller than any pull.

On the unfolded view, mark the upper and lower boundaries of the handles, horizontal joints of fronts, and protruding elements. A single line indicating the center of the bracket is not enough. This especially applies to the vertical position: it changes the height-occupied section and may bring the end of the handle closer to another drawer.

In the initial record, it is useful to distinguish three types of distances: between handles, between a handle and another front, and space for the hand. These checks answer different questions. The ability to close the doors does not yet mean that the bracket is comfortable to grip.

The door opens

With the adjacent drawer closed, the entire required path of the door is checked—from the initial position to the position needed for using the cabinet. It is not enough to compare only the closed and fully open options: intermediate convergence will go unnoticed.

The movement is defined by a specific hinge and its installation. Do not draw an arbitrary arc around the visible corner of the body and take it as the exact trajectory of the handle. For a working project, data from the selected hardware or verification of the assembled unit is needed. What is checked is not abstract "90 degrees," but the ability to perform the task: retrieve the needed item, open the internal fittings, return the object to its place.

If an obstruction appears during preliminary fitting, record which surfaces came into contact and in which phase. The phrase "the door does not open" is insufficient for correction. The end of the bracket on the adjacent facade, the middle of the handle near someone else's bracket, and the edge of the door itself require different solutions.

On a physical mock-up, the movement is performed slowly, not bringing contact to impact. A protective pad helps preserve the surface during fitting, but does not turn a collision into an acceptable working mode. Taping up the adjacent door against future marks instead of changing the design is a poor conclusion to checking a new kitchen.

The drawer extends

The door is returned to the agreed initial position and the drawer's travel is checked. The entire moving facade with the handle is considered, not just the drawer inside the body. The required depth of extension is also important: a small initial movement does not yet confirm access to the contents.

Each drawer of the problematic block should be checked. The upper and lower ones differ in handle height, position relative to the adjacent door, and sometimes the facade construction itself. A successful fitting of one bracket is not a check of the entire vertical group.

Ask to show the path of the handle end closest to the corner on the plan and compare it with the height of the obstruction. Such an analysis helps distinguish a case where a different length is sufficient from a situation in which a handle of either of two lengths remains in front of the perpendicular door.

Do not intentionally use a skewed facade position as a way to gain clearance. The check must correspond to normal, agreed furniture adjustment. If the drawer only passes after noticeable displacement relative to the other facades, the project needs to be reconsidered, not this adjustment fixed as a hidden compromise.

A normal sequence of actions is being performed

The last check relates to using the kitchen. Imagine a specific action: open a cabinet, take a pot, then retrieve an item from the adjacent drawer. Note whether you need to keep the door open or if closing it does not cause inconvenience.

Not all adjacent fronts need to open simultaneously. But the chosen sequence must suit the owner. If every access to a frequently used drawer requires first completely clearing another module, this must be discussed before ordering, not explained as a feature of an already assembled kitchen unit.

The reverse closing order is also checked. The handle may pass in one door position and encounter an obstacle when the user starts to return it back. For a family where several people use the kitchen, a solution without an non-obvious instruction about which panel to move first is more convenient.

It is convenient to record the check not with the general word "fits," but by individual actions. Such a sheet is filled in based on the actual result; the absence of a comment is not considered automatic confirmation.

When noticing an issue, attach a photo or a model fragment of the problematic position specifically. Mark it on the diagram so that the next variant is compared with the same situation. Otherwise, moving the handle may eliminate contact in one drawing but leave it in another position that was forgotten to be shown during repeated discussion.

The result is recorded as a short note for the D-1/Ya-1 pair: which states were checked, which Taurus length was chosen, where it is located, and what constraints were accepted. The phrase "it seems to open" does not replace this result. The numerical working clearance and permissible tolerances are assigned by the kitchen manufacturer; zero contact on the sketch should not be considered sufficient clearance for final installation.

Where to place wooden handles to preserve opening and facade design

After identifying an obstacle, it is useful to compare variants sequentially, changing one parameter at a time. First, two lengths with a common axis. Then, the permissible shift of the selected handle. After that, if necessary, consider a different orientation or a change in the corner joint. This way, it is clear which change actually solves the problem.

Shifting along the facade makes sense when the end of the handle can be moved out of the conflict zone. But the new position must allow for mounting and maintain a comfortable grip. On a framed facade, the construction of the specific section is checked, rather than assigning holes solely based on a beautiful external line.

Vertical placement changes the section of the facade occupied by the handle, but it is not a universal solution. The top or bottom end may end up next to an adjacent drawer; hand access may become worse. Rotating the handle in the drawing also does not confirm the acceptability of such installation. It is coordinated considering the product and the door construction.

Changing the filler panel or module is considered together with the kitchen manufacturer. Unlike a local handle relocation, it affects the entire corner layout. After the adjustment, movement, the position of adjacent facades, and the coordinated layout are re-checked. The visible gap must not be increased by accidentally disrupting the cabinet installation.

When a working option is found, look at the kitchen as a whole. Brackets may have different lengths, but there should be a clear overall system: coordinated axes, heights, and orientation on each group of facades. Otherwise, a technically successful corner will look as if it was marked separately from the rest of the furniture. General principles are covered in the material how to choose handles for kitchen facades.

For a visual trial fit, use a paper outline of the full dimensions. After printing, measure it with a ruler: the "fit to page" setting can change the scale. On the template, mark the center of the outer outline to avoid confusing it with the mounting mark.

A scaled layout is suitable for composition, but checking a small gap on a printout is inconvenient. At a scale of 1:10, one millimeter on paper corresponds to ten millimeters in reality. Line thickness or printing inaccuracies can hide a significant close approach. Therefore, critical areas are examined in an enlarged fragment with dimensions or on a full-size trial fit, rather than measured on the overall kitchen image.

For a preliminary space check, a three-dimensional mock-up that replicates the confirmed external dimensions and handle position is needed. It shows potential intersections but does not check mounting strength and does not replace a trial fit with the actual product. The temporary attachment method must not damage the facade; pulling a working drawer by a paper template or an unreliable mock-up is not allowed.

When it is better to avoid Taurus in the corner: no coordinated position provides the required opening, the grip is uncomfortable, the installation falls on an unsuitable section of the facade, or the solution requires modifications that the customer does not accept. Then you can Buy wooden furniture handles use a different design after separate verification. This is a rejection of an unsuitable combination, not a conclusion about the model's unsuitability for all kitchens.

How to transfer the verified Taurus to the rest of the cabinet set

Now a list of all installation locations is being compiled. Facades receive numbers matching the layout. Length and orientation are specified for each location, even when most of the kitchen uses the same handles.

Do not automatically assign one handle to any facade. The quantity is determined by the furniture design and the agreed layout. A false panel, an inner drawer, and an outer door are different positions, even if they look like similar rectangles in the sketch.

The appearance of the set is checked on a sample next to the facade and countertop. The name of the wood and metal finish is recorded identically in all rows; matching the natural wood grain across different pieces is not promised. After that, you can buy wooden handles with coating based on the completed list.

A trial piece is accounted for separately. If one paid handle fit and went into a set of eight, you need to buy seven more. If two lengths were tried, but only one went into the project, the cost of the second piece remains an expense for testing. A free sample or return after installation is not anticipated in advance.

Price of the Taurus set: comparing lengths in the same finish

As of September 6, 2026, the following prices are listed in the card for the walnut / stainless steel combination. The table assumes a hypothetical project of eight handles; this is not a recommendation of quantity for any kitchen.

The difference is 32,880 − 30,240 = 2,640 ₽. This is the cost of the items themselves, without delivery, additional components, or installation. The cheaper option does not solve the task if it has not passed the corner spot check.

A mixed set is calculated by line items, not by average price. For example, if after approval six short and two long handles are needed, the product total will be:

6 × 3 780 + 2 × 4 110 = 30 900 ₽.

This set is provided only for arithmetic: placing two long brackets here is not assigned. In the work order, each group corresponds to a list of facades.

The full budget consists of handles per the list, actually necessary components, an additional sample outside the final set, delivery, and installation. Costs for project review are accounted for by agreement with the contractor. An already paid and included sample is not added again to the product total.

Before payment, confirm the current price and availability of the entire set. The displayed stock does not equal a reserve for your order, and two consecutive purchases may require separate deliveries.

What to order together with the handles, and what not to add automatically

Fasteners are selected based on the confirmed mounting diagram and the front's structure. You need to know its thickness exactly at the installation point, access from the reverse side, and possible obstructions from drawer parts. The screw length cannot be assigned only by the overall door thickness: the entire connection assembly must be considered.

Also check the assembly sequence: whether the tool can be brought to the handle attachment after installing the facade on the drawer. If necessary, the contractor arranges installation at the appropriate stage. A visible convenient bracket position should not lead to an inaccessible connection that then has to be disassembled together with neighboring elements.

The recommended products block is not a list of package contents. First, find out what is supplied with the handle, then add missing items. This protects against both unnecessary purchases and a halt in installation due to a missing part.

For example, you can buy FUR-033 plugs, if they are needed for coordinated mounting. According to the manufacturer's description, these are decorative metal elements for hiding the head of an M4 screw with a semi-round head. The cap does not replace the screw; its necessity and quantity are determined by the actual assembly. Before installation, also check that it does not interfere with neighboring parts on the reverse side of the facade.

Order Taurus HL-060-1M wooden handles according to the agreed scheme

For each length, create a separate line. The short version can be written as follows:

Taurus HL-060-1M / 245 × 15 × 37 × 160 mm / walnut / stainless steel / quantity ___ pcs.

Placement — according to the attached facade list and the agreed corner location diagram. Confirm completeness, installation drawing, fasteners, current price, and delivery time. Sample: included / not included in the specified quantity.

For the long version, the entire size is replaced with 309 × 15 × 37 × 224 mm, not just the first number. Attach a general layout and a verified diagram of the problematic pair with indication of permissible states to the request.

Separate the confirmations: the seller specifies the product and delivery, the kitchen manufacturer — the operation of the accepted structure. The manager's response about handle availability is not approval of drawer opening. Before drilling, the contractor verifies the received items against the approved diagram; changing the length at the last moment requires revision of the layout.

Check payment and delivery terms for handlesthen you can order Taurus HL-060-1M for the agreed project. A finished order is the selected version, exact quantity, and clear placement of each handle, not eight identical names without installation reference.

Questions before buying handles for a corner kitchen

Can I leave long handles on the straight section and put short ones only near the corner?

Yes, this option can be considered. The operation of the corner area and the overall look of the set are checked. Different lengths are reflected in the specification so that the installer does not rely only on the external similarity of the items. The idea of a mixed set itself does not yet confirm a suitable layout.

What to do if hinges or guides were replaced before making the facades?

Repeat the check of the affected modules using the new data. The preserved dimensions of the cabinet body do not mean that the movement remains unchanged. The updated diagram must reach the person responsible for marking the handles, and the previous version must be excluded from the working documents.

Can Taurus be installed on the facade of a built-in dishwasher?

This is a separate point of verification. Requirements for the facade, mounting, and opening are taken from the documentation of the specific appliance. Successful placement on a neighboring furniture drawer does not confirm compatibility with the appliance door. Such a facade should not be drilled according to the general specification without coordinating its features.

Is it enough to send the kitchen manufacturer just one photo of the corner?

A photo is useful, but it does not replace dimensions and hardware data. At least a plan of the problematic pair, a vertical elevation, and references for the selected handles are needed. A photo of a closed kitchen does not show the path of parts during opening.

Can a door opening limiter resolve the collision?

Only if a suitable solution is permitted by the selected hardware and maintains the required access to the cabinet. The limitation is coordinated with the furniture manufacturer. A homemade stop or a habit of holding the door does not replace testing the new design.

Can I order the entire batch while the handle positions are still being discussed?

This creates a risk of purchasing the wrong length or quantity. Before the final list, it is wiser to agree on a trial purchase and the terms for a further order. One liked sample is not enough to pay for the set if the problematic corner location has not yet been checked.

Do I need to re-check the corner after the entire kitchen is installed?

Yes. Checking the design and accepting the assembled furniture are different stages. After final adjustment, repeat the agreed actions and ensure that the actual handle position matches the diagram. If an obstruction is found, do not continue moving with force.

Can one spare handle be purchased in advance for the entire set?

A reserve can be planned, but it must match the specific group. In a set with two lengths, one spare handle will not automatically replace any other. Specify which version it is intended for, and do not include it in the count of installed items when calculating facades.