Buy wooden bed legs: spiral MN-088 or classic MN-094 100 mm high — which to choose

Wooden bed legs rarely remain completely invisible. Even at a low height, they form the bottom line of the frame, set the distance from the floor, affect the perception of massiveness, and connect the bed with nightstands, dressers, and other bedroom furniture. Therefore, two supports of the same height can yield different results: one becomes an expressive detail, the other calmly completes the base and does not compete with the headboard.

This is exactly the fork created by MN-088 and MN-094. Both models have a height of 100 mm and a B size of 90 mm, are made from beech for enamel and oak for tinting, are offered with "Prestige" sanding, and are supplied without a finish coating. By technical purchase logic, they are similar, but the turning pattern differs noticeably. MN-088, size 100 × 90 × 84 mm, has a spiral relief that reads well on an open base. MN-094, size 100 × 90 mm, looks calmer and is easier to combine with an active headboard, textile upholstery, or already rich bed decor.

Choosing between them based only on the word "classic" or a single large photo is not enough. You need to understand how visible the legs will be, where the lower edge of the side rail runs, how many supports the frame requires, whether there is a center beam, how the mounting point is arranged, which fastening kit is suitable, and whether floor protection is needed. A height of 100 mm alone does not indicate the total height of the sleeping area or the actual clearance for cleaning.

Below, we compare two specific models as purchasing decisions. The article will help determine when the expressive spiral of MN-088 truly enhances the design, and when the universal MN-094 is more accurate; how to calculate the bed height; how many legs to add to the order; how FUR-001 and FUR-012 differ; which glide to choose, and what to check before installation.

Buy MN-088 Buy MN-094 View all bed legs

Bed Headboard KRVT-001-1

from 1,697.74 $

Bed End KRVTC-001-2

from 876.86 $

Carved Furniture Leg MN-002

from 107.84 $

Carved Furniture Leg MN-018

from 31.23 $

Turned leg with decoration MN-145.1

from 10.98 $

Carved Bed Frame KRVT-001

from 5,046.85 $

Wooden Christmas balls SUV-002

from 12.32 $

Precision Furniture Leg MN-233

from 29.03 $

Go to Catalog

How MN-088 differs from MN-094

The main difference is not in height or wood species. Both supports raise the frame by the same 100 mm before accounting for the mounting assembly, both have a size B of 90 mm, both can be ordered in beech or oak. Therefore, the choice shifts to the area of pattern, visibility, and overall stylistic impact.

MN-088 has an active spiral relief. Light and shadow travel along the twisted pattern, so the leg is readable even with a solid finish. The more contrasting the lighting and the freer the space under the rail, the more noticeable this effect. MN-094 is built on a calmer rounded turning. It retains a classic character but does not require other details to repeat the spiral.

The table shows an important principle: MN-094 cannot be considered a "simpler version" of MN-088, and MN-088 is not automatically more suitable for any classic bed. Expressiveness must be appropriate. If the side rail covers almost the entire leg, complex relief may be lost. If the bed already has a tall carved headboard, capitonné, decorative nails, and active textiles, an additional spiral sometimes overloads the lower part.

Watch video ...

How a wooden leg changes the structure and perception of a bed

The leg performs several tasks at once. It transfers the load from the frame to the floor, creates a support contour, sets the clearance, helps shape the architecture of the lower part, and contributes to the style. These functions cannot be separated: a beautiful support installed in an unsuitable mounting point does not become a good solution; a technically compatible leg chosen without considering the design may look random.

Our factory also produces:

Turned leg with decoration MN-148

from 16.47 $

Decorative leg MN-149

from 17.93 $

Wooden Rose R-012

from 6.34 $

Wooden rose R-046

from 16.59 $

Turned Furniture Leg MN-178

from 30.25 $

Precision Furniture Leg MN-179

from 33.43 $

Geometric Furniture Leg MN-205

from 56.97 $

Modern Furniture Leg MN-228

from 14.76 $

View Full Product Catalog

Support contour

The position of the outer and central legs determines how the bed handles the load. Four corner supports are not suitable for every frame. A long double bed often has a central longitudinal beam, its own orthopedic base, and additional support points. The quantity and arrangement are specified by the frame manufacturer or designer.

Clearance above the floor

A leg height of 100 mm does not equal a free clearance of 100 mm. The lower edge of the side rail may be below the top platform of the leg, the fastening may be recessed, and the decorative part of the support may be partially hidden. For a robot vacuum or manual cleaning, the actual distance from the floor to the lowest part is measured, not just the nominal height.

Lower furniture line

MN-088 adds rhythm and diagonal movement. MN-094 creates a calmer sequence of rounded supports. With four visible legs, the difference is already noticeable, and with six or more, the repetition of the pattern becomes even more important. Therefore, the set is evaluated as a whole, not by a single leg in close-up.

Connection with other furniture

A bed rarely stands alone. Nearby are nightstands, a bench, a dresser, and a vanity table. The calm MN-094 more easily combines items of different designs. MN-088 requires either repeating the spiral motif or intentional contrast. Both approaches are possible, but random mixing usually looks less cohesive.

When to buy the spiral leg MN-088

MN-088 should be chosen when the pattern will actually work. Its spiral is not a hidden technical detail, but a decorative motif. If the legs are almost completely covered by a wide apron or a long bedspread, the buyer gets a complex relief that is barely visible in the finished bedroom.

The bed has an open base

The best scenario for MN-088 is a frame where there is enough space between the floor and the bottom edge. The spiral receives side light, does not hide in the shadows, and is perceived as part of the overall shape. Before ordering, you can make a paper template 100 mm high and attach it to the bottom line of the bed.

If the visible supports should become a decoration of the base, you can buy the MN-088 leg after checking the mounting node and quantity. For the set, identical orientation and a uniform finish of all parts are important.

The frame is calm and straightforward

The spiral works especially well next to simple side rails. It adds character without the need to complicate the entire frame with carving. This combination suits a classic and vintage bedroom where one noticeable motif is needed, but not a fully decorated bed.

There are already twisted details in the room

The spiral can echo furniture columns, turned handles, banquette legs, mirror frames, or lamps. The connection doesn't have to be literal: it's enough to repeat the direction of lines and the character of the plasticity. Then furniture legs with spiral relief become part of the system, not a separate decoration.

Expressive finishing is planned

Beech MN-088 can be painted with enamel, oak — tinted while preserving the texture. The contrast of light and shadow enhances the spiral. With dark tinting, the relief appears deeper; with light enamel, it looks more architectural. However, too thick a coating can smooth out the turning boundaries, so the finish must be applied carefully.

You need to separate the bed from the calm furniture

Sometimes the bed should become the main item in the bedroom, while nightstands and wardrobes serve as the background. MN-088 helps enhance the frame's individuality without changing its height. This is especially useful when restoring or updating furniture, when you want to replace ordinary supports with more distinctive ones.

When to choose the classic MN-094

MN-094 is not a compromise or a "less decorative" product. Its strength lies in versatility. The calm turned profile allows it to support classic furniture without introducing a new mandatory motif. Therefore, the model is appropriate in bedrooms where attention is already focused on the headboard, fabric, carving, or wall architecture.

The bed has a soft headboard

Capitonné, piping, decorative nails, a tall fabric panel, and complex textiles create enough detail. MN-094 neatly finishes the base and does not require repeating the spiral in other elements. The legs remain classic but visually calm.

There is a carved headboard or footboard

When the top of the bed is rich with carving, the lower part usually benefits from a simpler support. MN-094 helps distribute attention: the main decor stays above, while the legs maintain proportions. This does not mean MN-088 is forbidden; it just needs to be checked in a mockup so that two active patterns do not conflict.

Need to connect the bed with nightstands and a dresser

A rounded classic profile is easier to repeat or support with neutral legs of other furniture. If the bedroom is assembled from different collections, MN-094 reduces the risk of stylistic mismatch. For a buyer who plans to buy beech wood bed legs to match the overall enamel with the nightstands, the model provides a clear path.

The supports are partially visible

If the side rail or bedspread covers the upper part of the leg, the complex relief of MN-088 may be read fragmentarily. MN-094 handles partial visibility better: the rounded silhouette remains understandable even when only the lower part is exposed.

A universal commercial option is needed

MN-094 is already linked to the main queries about wooden bed legs. But for the buyer, what matters more is not the search position, but the fit with the project. You can buy the MN-094 leg, if you need a universal profile 100 × 90 mm, beech under enamel or oak under tinting, and a calm finish for the frame.

Why the same height does not mean the same result

The buyer might think that MN-088 and MN-094 are interchangeable because both have a height of 100 mm. In terms of external dimensions, they are indeed close, but the design, side contour, and additional size of MN-088 change the fit and perception.

The relief creates different shadows

The spiral of MN-088 forms diagonal shadow stripes. MN-094 gives calm horizontal and rounded transitions. With side lighting, the difference increases. In a dark niche under the bed, it may decrease, so the position of the lights and the height of the side rail also affect the choice.

Repeating several legs enhances the pattern

One spiral seems like a small detail. Six identical supports create a noticeable rhythm. When calculating a set, you need to look not at a single card, but at the entire row. MN-094 remains calmer in large quantities.

The fit size needs to be checked separately

The same size B 90 mm does not guarantee that the old hole, plate, and offsets fit without changes. MN-088 has an additional size D 84 mm, while for MN-094 it is not specified separately. Replacement requires checking the drawing and the actual top platform.

The finish changes the character

White enamel makes the spiral graphic and architectural, dark tinting makes it deep and traditional. MN-094 in a light color looks lighter, in a dark color it looks more substantial. Therefore, the final choice of model is best made together with the decision on material and color.

How 100 mm legs affect the final bed height

The leg height is only one element of the vertical calculation. The total sleeping area height consists of the support, frame, mattress base, mattress itself, and possible installation gap. If you replace the legs but do not account for the other layers, the bed may end up higher or lower than expected.

Final height of the sleeping area = leg + structural height of frame and base + mattress thickness + actual installation gap.

This calculation shows the principle, not a recommended standard. The actual height depends on the project. Even two frames with identical legs can differ by tens of centimeters due to the side rail, base, and mattress.

How to check comfort

Sit on an existing bed or a stable surface of the intended height. Assess whether it is comfortable to get up and whether your knees are not too high or too low. Comfort varies for different people, so a universal value does not replace a fitting.

Will the height be suitable for a robot vacuum cleaner

The mere presence of a 100 mm leg does not guarantee device passage. Measure the clearance to the lowest part: the apron, central beam, fasteners, or decorative detail. Also consider thresholds and carpets. The article cannot promise compatibility with specific equipment without its dimensions and the bed's drawing.

Ventilation and cleaning

A raised base facilitates air access and cleaning, but the actual effect depends on the design. If the apron almost touches the floor, the leg may be hidden and the clearance may be small. Check the finished cross-section, not just the product height.

How many supports are needed for a single and double bed

The number of legs is determined by the design, not the model name. You cannot automatically order four MN-088 or MN-094 and consider the set complete. Corner supports hold the perimeter, but long aprons and the central part may require additional support.

Corner legs

They form the outer contour and are usually more visible. This is where the choice between MN-088 or MN-094 is especially important. If the central supports are hidden, their external pattern may be less important, but mixing different models without a structural and visual concept is not advisable.

Central longitudinal beam

For a double bed, it helps support the base and reduce the span. The number of central legs depends on the length, design, and manufacturer's recommendations. Calculation cannot be replaced by the assumption that one support in the center will solve any problem.

Same or different legs

External supports can be made decorative, while hidden central ones can be technical, but such a scheme must be confirmed by height and load. If all legs are the same height, it does not mean the nodes work identically. For the buyer, it is easier to order a complete coordinated set after the drawing is approved.

How to check the attachment to the frame

Both cards indicate FUR-001 and FUR-012 as options for the required fittings. This does not mean that any set can be installed on any frame without checking. The frame material, part thickness, thread, hole location, and the ability to tighten the connection are important.

Material of the mounting area

The fastener must work in the strong part of the frame. Thin veneer, hollow apron, damaged old hole, or weak board require a separate solution. Before ordering, remove the leg, photograph the joint, measure the thickness, and show the data to the master.

Edge offset

The plate or stud should not be located too close to the edge where the wood could split. The specific offset is determined by the design. The corner area is often limited by the apron connection, so free space needs to be checked from below.

Thread and orientation

If an M8 connection is used, all components must be compatible. Fasteners cannot be selected only by approximate diameter. After tightening, the MN-088 spiral must be oriented identically on visible legs if the shape allows a visually noticeable direction.

Dry fitting

Before final finishing, it is useful to temporarily install the legs, place the frame on a level floor, and check the height, diagonals, wobble, and visibility. Such a trial fitting shows whether the apron hides the spiral and whether the MN-094 looks too massive or, conversely, insufficiently noticeable.

FUR-001 or FUR-012 — which kit to choose

FUR-001 is conveniently considered as one of the confirmed options for both models. But the composition and fit need to be verified in the current card. If the buyer plans to buy a bracket for bed legs, the correct sequence is to first measure the frame, then select the kit.

FUR-012 is also specified for MN-088 and MN-094. The plate distributes the connection over the surface, but it requires a free and strong area. Can buy mounting plate for leg after checking that it does not conflict with the corner joint, lamellas, or internal fittings.

Can I use old fasteners

Sometimes it is possible if the thread, condition, and geometry match completely. But an old stud or plate cannot be considered suitable just because it looks similar. Worn threads, play, and wood damage require repair.

Do I need to buy a fastener for each leg?

The number of sets depends on their composition and scheme. Before ordering, match the number of supports and mounting nodes. Do not order fittings "approximately": a shortage of one element will stop assembly, and extra parts may be unnecessary.

Beech for enamel or oak for tinting

Both models are available in beech and oak. In the provided product scheme, beech is associated with enamel, oak with tinting. This is not just a choice of wood species, but two different visual routes.

Beech for enamel

Beech is suitable for opaque color. White, milky, gray, dark, or colored enamel helps connect the legs with the frame and other furniture. On MN-088, a solid color emphasizes the shadow of the spiral. On MN-094, it creates a calm, solid silhouette.

For a buyer who needs beech legs for enamel, the color should be coordinated according to a sample. The shade name does not guarantee a match with an already painted frame. Even white coatings differ in temperature and gloss.

Oak for tinting

Oak is chosen when you need to preserve the visible wood texture. Tinting can support the oak frame, cabinets, or floor. On the MN-088 spiral, the fibers follow the relief and create a complex interplay, while on MN-094 the texture is perceived as calmer.

If planning buy oak bed legs, it is better to order all visible supports at the same time and finish them with one system. Natural material has differences, but a unified technology helps assemble a complete set.

What to choose for a white bed

Beech for enamel is the direct route. But the white color does not have to make both models identical. MN-088 remains more active due to the spiral, MN-094 is calm. The choice of shape retains its significance after painting.

Can beech be tinted?

Within the scope of this article, you should rely on the confirmed scheme: beech is prepared for enamel, oak for tinting. Other options need to be clarified separately in the product card or with a STAVROS manager, without assigning them yourself.

How to finish the legs without losing the turned pattern

The "Prestige" sanding creates a prepared surface, but the final coating still requires technology. The error often appears not when choosing the article, but at the stage of priming and painting.

First, a test sample

Check the color and coating thickness on a sample of the same wood species. This is especially important for oak tinting: the texture and absorption affect the result. For enamel, the test shows coverage and gloss.

Do not flood the spiral

MN-088 has a more complex relief. Excess soil and enamel smooth out the boundaries. Several controlled layers are usually safer than one excessively thick one, but the master chooses the specific system.

Paint the set simultaneously

If four outer and two central legs must be identical, they are processed as one batch. Separation in time may result in differences in shade and gloss. Central supports may be less visible, but the height of the coating and foot pads still affects the plane.

Protect installation areas

Threads, seating areas, and connection points should not be accidentally filled with material. Before finishing, determine which surfaces remain technological. After drying, check if the coating interferes with tightening.

How to select foot pads and protect the floor

The foot pad is located at the bottom and performs a different task than the mounting plate on top. FUR-022 and FUR-028 are listed as suitable options for both models. The choice depends on the floor, the method of attachment, and whether the bed will be moved.

FUR-022 — round foot pad

FUR-022 has a diameter of 30 mm. It creates a separate contact point and helps protect the lower surface of the wooden leg. Before purchasing, check the fit and fastening method. Can buy a foot pad for the bed leg after agreeing with the selected model.

FUR-028 — felt foot pad

FUR-028 has a diameter of 28 mm and a felt contact part. This option is useful for parquet and other coverings where soft protection is important. The fitting card confirms that the product should not be confused with an arbitrary self-adhesive pad: the installation method must be checked.

For a bedroom with parquet, you can buy felt pads for the bed, but only after calculating the number of all supports. If the center legs also touch the floor, protection is needed not only on the four corners.

Is it possible to install new legs instead of old ones

Replacement is possible if the frame is in good condition, the mounting point can be adapted, and the new height matches the project. A simple match of the external size is not enough.

Remove one old leg

Before ordering, it is useful to dismantle one support and examine the connection. Measure the thread, top platform, hole depth, frame part thickness, and distance to the edge. Take photos with a ruler.

Check all points

Old beds may have different wear at the corners. One mount is preserved, another is loose. Repairs are carried out before installing new legs. Damage cannot be compensated by overtightening.

Compare final height

If the old legs were 70 or 150 mm, switching to 100 mm will change the height, clearance, and position of the bed relative to the nightstands. It may be necessary to adjust the level of the bedside furniture or choose a different model from the catalog of oak and beech legs.

Check visibility

After replacement, the bedspread may cover the legs or, conversely, expose the lower part of the frame more. MN-088 should only be chosen when the spiral is actually visible and appropriate. For a hidden base, MN-094 is often more rational.

How to combine legs with headboard and nightstands

Upholstered headboard

Textiles already add texture and volume. MN-094 supports a calm base. MN-088 is possible if the fabric is solid, the frame is straight, and the bedroom needs a small decorative contrast.

Carved wooden headboard

First, determine the dominant pattern. If the carving has twisted lines, MN-088 can continue the motif. If the pattern is complex and layered, MN-094 helps avoid overloading the furniture.

Tall simple headboard

Both models are appropriate. MN-088 adds character from below, MN-094 maintains architectural rigor. The choice can be linked to the handles of the nightstands, the mirror frame, or the legs of the bench.

Nightstands

It is not necessary to put exactly the same supports on the nightstands. Matching material, color, and character is important. MN-094 is easier to combine with different shapes. The spiral MN-088 requires either repetition or consciously neutral neighbors.

Dresser and bench

If all items have different legs, unify them with the finish. Oak tinting or a single enamel helps assemble the set. But too many different turned patterns can make the bedroom look like a random selection.

Practical selection for different scenarios

How not to confuse MN-088 and MN-094 with similar products

Check the full article number

The numbers 088 and 094 cannot be replaced by the description "round leg 100 mm". The catalog contains other supports of similar height. The article number links the specific shape, dimensions, and product card.

Do not confuse the leg height with the clearance

100 mm is the product size. The free space depends on the apron and mounting. A separate measurement is needed for cleaning.

Do not confuse the foot with the mounting

FUR-001 and FUR-012 connect the top of the legs to the frame. FUR-022 and FUR-028 are located at the bottom and protect contact with the floor. These parts do not replace each other.

Do not consider oak and beech as the same finishing route.

In the article, beech is considered for enamel, oak for tinting. The choice of wood species must be made before ordering, not after receiving the kit.

Do not buy four legs without checking the frame.

A double bed may require central supports. First the diagram, then the quantity.

Mistakes when buying bed legs.

Choosing MN-088 based on a beautiful large photo without checking visibility.

Under the side rail and bedspread, the spiral may disappear. Make a 100 mm template and evaluate the bed in a real interior.

Considering MN-094 too simple.

A calm profile often works better next to an active headboard. Versatility is an advantage, not a lack of design.

Order only four supports

A double bed may have a center beam. Missing parts will delay assembly and may create an unsuitable structure.

Not checking the thread and seat

Even confirmed hardware requires compatibility with the specific frame. Measure the joint before purchasing.

Mixing beech and oak in one visible set

Wood species differ in texture and finishing route. If mixing is not intended, order the same material.

Applying thick enamel to MN-088

The spiral loses clarity. Finish control is done by layers and a test sample.

Forget about glides

A wooden leg without proper protection can damage sensitive flooring. Glides are calculated based on the total number of supports.

Expect the robot vacuum to pass due to the 100 mm figure

The drawer may be lower. Measure the actual clearance after assembly or from the cross-section.

Changing legs without checking the height of the cabinets

The new bed height affects the convenience of the bedside area. Align the top of the mattress with the nightstand.

Not verifying the current product card

Availability, material, completeness, and parameters are checked before ordering. The article explains the choice but does not replace the current information on the website.

Who MN-088 suits and who should choose a different leg

MN-088 suits a buyer who sees legs as part of the design. It is appropriate for an open base, simple drawer frames, classic, vintage, and eclectic bedrooms, as well as interiors with twisted decor. The spiral can be highlighted with enamel or oak tinting.

MN-088 may not be suitable if the legs are hidden, the headboard is already very busy, and nearby there are items with several different patterns. In such a situation, MN-094 or another model from the selection of bed legs will be more accurate.

Who MN-094 suits and who should consider MN-088

MN-094 is suitable for soft and wooden beds where a calm classic base is required. It connects more easily with nightstands, dressers, and different styles, works well with partial visibility, and does not require repeating a specific pattern.

MN-094 may be too neutral if the bed has simple straight side rails, minimal textiles, and should have a noticeable decorative base. Then spiral bed leg will add the needed character without changing the height.

How to buy MN-088 or MN-094 at STAVROS

Start with a drawing or frame measurements. Determine the number of corner and center supports, type of attachment, side rail height, actual clearance, and landing zone material. Then choose the shape.

For the spiral base, open the MN-088 card and check the size 100 × 90 × 84 mm, beech or oak, sanding, and current configuration. For the calm option, open MN-094 size 100 × 90 mm. If neither model fits, you can buy bed legs from the general selection and compare other heights.

Then choose FUR-001 or FUR-012 based on design. Add FUR-022 or FUR-028 considering the floor. It is better to order all visible supports in the same wood species and finish them at the same time. For a broad search not only for beds, use catalog of unfinished wooden furniture legs.

Additional materials on choosing legs

The general route by height, shape, quantity, and attachment is covered in the material "Wooden legs for a bed: how to choose height, shape, and attachment". If you need to compare not only MN-088 and MN-094, but the entire class of low supports, the article is useful about legs 10 cm high for beds and other furniture. A historical overview of shapes and the role of details can be seen in the publication about wooden legs as the finishing touch of a bed.

Result: MN-088 or MN-094

Choose MN-088 if the spiral should be visible and supported by the interior. It makes the base expressive, adds movement, and works especially well with simple side rails. Choose MN-094 if you need a calm classic profile that can support an active headboard, textiles, and various bedroom furniture.

The height of the models is the same — 100 mm, size B is 90 mm, materials and preparation for finishing match. Therefore, the decision cannot be made based on height. Compare the relief, visibility, number of supports, fastening, material, and floor protection.

Before ordering, check the central beam, orthopedic base, actual clearance, final mattress height, and mounting assembly. Only after this does the set of MN-088 or MN-094 become part of a well-thought-out design, not a random replacement of old legs.

FAQ: questions about MN-088 and MN-094

Is the height of MN-088 and MN-094 the same?

Yes, both models have a height of 100 mm and size B of 90 mm. MN-088 additionally has a size D of 84 mm. The final bed height also depends on the frame, base, and mattress.

What is the difference in the shape of the two legs?

MN-088 has a noticeable spiral relief. MN-094 has a calmer rounded turned profile. The first is more active, the second is more versatile.

Which legs are better suited for a bed with a soft headboard?

More often MN-094, because it does not conflict with fabric, capitonné, and edging. MN-088 is possible with a calm solid upholstery and an open base.

Which model to choose for a classic wooden frame?

Both are suitable. MN-088 — for a pronounced decorative base, MN-094 — for a restrained classic finish. Look at the pattern of the headboard and side rails.

Will 100 mm high legs work with a robot vacuum?

Not necessarily. Measure the distance from the floor to the lowest part of the frame. The leg height is not equal to the clearance.

How many legs are needed for a double bed?

The quantity is determined by the design. Besides the four corner legs, central supports under the longitudinal beam or orthopedic base are often needed.

Is a central support needed?

It is needed if provided by the design or base structure. This issue cannot be decided solely by the bed width or the appearance of the legs.

Which fasteners to choose for MN-088 and MN-094?

The product cards specify FUR-001 and FUR-012. The choice depends on the frame, thickness, thread, and available area. Compatibility is confirmed before ordering.

Can new legs be installed instead of old ones?

Yes, if the mounting point matches or can be properly adapted, and the new height is suitable. First, remove one old leg and measure the attachment.

What to choose for white enamel — beech or oak?

In the approved design, beech is intended for enamel. Oak is chosen for tinting while preserving the texture.

How to preserve the wood texture?

Choose oak and agree on the tinting. Perform a test on a sample and finish the entire set with one system.

Are foot pads needed for the bed legs?

They help protect the floor and the lower part of the support. For the models, FUR-022 and felt FUR-028 are specified. The quantity is calculated based on all contact points.

Is it possible to install MN-088 on one side and MN-094 on the other?

For visible corners, this usually creates random inconsistency. Different models are only acceptable with a well-thought-out structural design, such as hidden central supports, but the height and load must be coordinated.

Which leg is better for a bed with a carved headboard?

Most often MN-094, if the carving is already complex. MN-088 should be chosen when the spiral repeats the headboard motif and does not create overload.

Do I need to buy fasteners separately?

Fasteners are selected separately. Before ordering, check the current product configuration to avoid waiting for items not included in the product.

What should be checked immediately before purchase?

SKU, size, material, quantity, central supports, mounting seat, thread, FUR-001 or FUR-012, glides, final height, and actual clearance.

Conclusion

MN-088 and MN-094 show why choosing wooden bed legs is not just about height. Both supports are 100 mm, available in beech and oak, and suitable for custom finishes, but they create a different character. MN-088 makes the spiral a noticeable part of the base. MN-094 completes the frame with a calm, classic profile.

A proper order starts with the structure: how many support points are needed, whether there is a center beam, which fasteners are suitable, where the apron runs, and what clearance will result. Then choose the pattern, wood species, finish, and glides. This sequence helps avoid a beautiful but incompatible purchase.

In the STAVROS catalog, you can open both product pages, compare them with other bed legs, and select confirmed hardware. A ready-made turned support allows you to focus on proper installation and finishing, rather than trying to assemble the base from random parts.

Project checklist before ordering and assembly

For a bed, a short specification is especially useful because supports, fasteners, frame, and base are often ordered from different contractors. One craftsman handles the side rails, another handles painting, and a third handles assembly. Without a common sheet, each person might interpret the 100 mm size differently: as the total leg height, as clearance, or as the distance to the bottom edge. A checklist eliminates this discrepancy and helps place an order without missing parts.

Write down the full SKU and material

The specification should say not "four round legs" but "MN-088, beech, 100 × 90 × 84 mm" or "MN-094, oak, 100 × 90 mm." If the outer and center supports differ, they are listed in separate rows. This way, the finisher won't mix up batches, and the assembler won't place a hidden technical leg on a visible corner. In a separate column, indicate the quantity and the selected glide.

Draw a vertical section

Show the floor, foot cap, leg, mounting unit, apron, base, and mattress. Provide actual dimensions. The section immediately reveals the clearance, where the upper part of the leg is hidden, and how high the sleeping area will be. For a robot vacuum, mark the lowest part, not just the leg length. If the bedspread hangs below the apron, it is also useful to indicate it: this will show whether the MN-088 spiral remains visible.

Draw a bottom view

The plan marks four corners, the central beam, intermediate supports, plates, and apron connections. This diagram helps calculate the quantity of FUR-001 or FUR-012, FUR-022 or FUR-028 and understand if there is enough space for the plates. For a double bed, the plan is especially important: the central part is often not visible after assembly but determines the structure's operation.

Compile a finishing list

Specify the wood species, color, gloss level, and sequence of operations. For beech — an agreed enamel, for oak — a selected stain. If the frame is already painted, a matching sample is required. The word "white" or "oak" is insufficient: shades and gloss can vary noticeably. For MN-088, additionally note the requirement to preserve the clarity of the spiral relief.

Determine visible sides

A bed against the wall and a bed in the center of the room are perceived differently. In the first case, the back legs are almost invisible; in the second, all sides are exposed. MN-088 is especially dependent on visibility. If the spiral is to be the main motif, ensure it is not covered by textiles or furniture. For MN-094, this issue is less critical, but a partially hidden leg should still look neat.

Clarify the assembly sequence

Some fasteners are more convenient to install before the final assembly of the side rails, some after. The finish must dry before tightening. Glides are placed on a clean bottom surface. The specific order is chosen by the craftsman, but it must be known before receiving the parts to avoid having to drill painted elements without preparation.

Perform a test assembly

Before installing the mattress, place the frame on a level floor, check all contact points, diagonals, and ensure there is no wobbling. Then add the base and repeat the check. The central supports must touch the floor as intended by the design. The glide is not used to correct a significant height error. If one leg does not touch the floor, the cause must be found, rather than simply increasing the thickness of the pad.

Keep a finish sample

It is useful to keep a color swatch or a small sample of the tone. If over time you need to replace a glide, repair a leg, or add a piece of furniture, the sample will help replicate the finish. This is especially important for complex oak tinting and non-standard enamel.

How to choose legs for different types of beds

Bed with upholstery around the perimeter

Upholstered side rails make the base visually voluminous. MN-094 usually supports such a frame more calmly: the rounded shape does not add another active pattern. MN-088 is suitable when the fabric is solid-colored, the legs are clearly visible, and the bedroom leans towards eclecticism or vintage. It is necessary to check that the fabric does not cover the top of the spiral and that the upholstery does not come into contact with the mounting plate.

Solid wood bed with straight side rails

A simple wooden frame offers more freedom. MN-088 adds a decorative motif, MN-094 maintains restraint. For an oak frame, both models can be chosen in oak for a unified tint. For painted furniture, choose beech under enamel. It is important to coordinate the grain direction and color of all visible parts.

Bed with high footboard

The footboard covers part of the front legs and itself becomes a noticeable element. If it is carved or shaped, MN-094 more often helps maintain balance. With a simple straight footboard, MN-088 can add expressiveness to the lower corners. Make a front sketch, because from this side both legs are usually most visible.

Bed without footboard

The front legs are exposed and become part of the silhouette. Here the difference between models is especially noticeable. MN-088 is suitable for a decorative effect, MN-094 for calm modern classics. On a bed without a footboard, it is also important to check that the supports do not protrude beyond the dimensions of the side rails and do not create inconvenience when passing.

Bed in a niche

In a niche, the side legs may be almost invisible, and the lighting from below is limited. The active relief of MN-088 in such a position sometimes does not reveal itself. MN-094 is more rational if the main task is a neat support without pronounced decor. At the same time, access to the fastening and the ability to pull out the bed for maintenance must be provided in advance.

Bed in the center of the room

All sides are open, so the uniformity of the set and the quality of the finish are especially important. MN-088 creates a noticeable repetition of spirals around the perimeter. MN-094 forms a calmer rhythm. If the bed is visible from the doorway and from the window, evaluate the legs under different lighting.

Care, operation, and re-inspection after installation

Checking fastenings after the first weeks

After assembly, the connections may slightly adapt to the load and material. Check for any play and extraneous sounds. Tighten the fasteners carefully, without damaging the threads and wood. If movement occurs, first determine the cause: loosening, damage to the seat, or uneven floor.

Checking the glides

Felt collects dust over time and can wear out. FUR-028 should be inspected periodically, especially if the bed is moved. Rigid FUR-022 is also checked for integrity and reliability of fastening. Worn protection is replaced before marks appear on the floor.

Cleaning the turned relief

The MN-088 spiral has more recesses where dust accumulates. A soft dry or slightly damp cloth compatible with the finish coating is suitable for care. Do not use products that could damage the enamel or tint. MN-094 is easier to wipe due to its calmer profile, but the turning boundaries also require attention.

Moving the bed

The bed should not be pulled by the headboard, forcing the legs to slide under load. First, free the structure, lift it in a coordinated manner, and control all supports. A felt pad reduces friction but does not turn a heavy bed into a mobile item.

Checking the central supports

After moving, the central legs may end up on a different area of the floor with a different height. It is necessary to re-check the contact and the absence of wobbling. If the floor has a pronounced difference, the master makes the decision; random pads under one support should not become a permanent structure.

Final checklist before placing an order

If at least one item remains unknown, it is better to clarify it before placing an order. This is especially true for the number of central supports and fastenings: these parameters cannot be corrected by simply choosing a beautiful shape. After filling out the checklist, it becomes clear whether you need the spiral MN-088, the universal MN-094, or another model from the STAVROS catalog.

How to choose a model based on bedroom style

Modern Classic

Modern classic allows both models but requires a clear hierarchy. If the bed has a smooth high headboard, straight side rails, and a calm palette, the MN-088 can be the only expressive turned motif. If the room already uses moldings, cornices, decorative handles, and textured textiles, the MN-094 helps keep the composition cohesive.

Traditional classic

For a traditional interior, the spiral MN-088 looks natural next to twisted carvings, columns, and oak tinting. The MN-094 suits beds with carved headboards where the lower part should remain calm. When choosing, it is useful to compare not only furniture but also doors, baseboards, frames, and lamps: the legs are close to the floor and interact with the lower architectural line of the room.

Vintage bedroom

The MN-088 strongly supports the image of restored or stylized furniture. It can replace simple old supports and make the bed more noticeable. However, the fastening of the old frame requires particularly careful inspection. The MN-094 is appropriate if the vintage character is already created by the headboard shape, patina, and hardware, and the new leg should only neatly complete the piece.

Neoclassicism in a light palette

Beech legs under enamel fit both models. In white or milky color, MN-094 looks calmer and connects more easily with straight cabinet fronts. MN-088 creates a more architectural play of shadows. For a small room with many light details, it's better to check the spiral on a full-size template so it doesn't appear overly active.

Eclecticism

In an eclectic bedroom, MN-088 can become a link between classic turning and the modern bed shape. Contrast is acceptable here, but it must be controlled: simple upholstery, minimalist nightstands, and one active support. MN-094 is useful when the room already mixes several eras and a new expressive pattern would be superfluous.

Calm modern interior

MN-094 is easier to integrate into a modern bedroom thanks to its rounded but not overloaded silhouette. MN-088 is also possible as a single accent, especially in dark monochrome finish. In this case, the bed should have simple side rails, and other decorative motifs should be minimized.

Purchase route: from idea to finished base

First, determine the structure

Before choosing a beautiful shape, you need to understand how the bed is built. Take measurements, find the center beam, count the support points, determine the material and thickness of the attachment point. If the bed is being made from scratch, the designer should provide this data. If the legs are being replaced, the old assembly needs to be disassembled and measured.

Then choose the role of the legs

Answer a simple question: should the supports be visible? If yes, compare the MN-088 spiral and the MN-094 calm profile in a full row. If not, it is more rational to choose a universal shape and pay more attention to the fastening, quantity, and floor protection.

After that, choose the material

For opaque enamel — beech, to preserve the wood texture — oak for tinting. Do not order the material separately from the finishing solution. Color and gloss affect how actively the relief is read. MN-088 can become more expressive, MN-094 — visually lighter or more substantial.

Then select the fastening and glides

FUR-001 and FUR-012 are checked against the frame. FUR-022 and FUR-028 are checked against the lower platform and floor type. The quantity of fittings is calculated for all supports, including hidden central ones. After this, the order becomes a complete set, not a collection of unrelated parts.

Finish with a test fitting

Before final finishing and installation, it is useful to assemble one unit or temporarily install the legs. Check visibility, height, and position. Such a fitting is especially valuable for MN-088: it immediately shows whether the spiral is revealed or almost completely hidden under the apron.

What to discuss with the manager or craftsman before payment

Before placing an order, it is useful to provide the specialist not only the model name but also a short set of initial data: photos of the frame from below, apron thickness, base type, estimated number of supports, floor material, and desired final height. For replacing old legs, add a photo of the removed fastening and thread measurement. For a new bed — a diagram of the central beam and plate locations.

Separately, clarify whether the selected hardware is included in the order or added as separate items, how many sets are required, and whether the glide is compatible with the bottom platform. If the finishing is not done at the factory, agree on the condition in which the beech or oak will arrive and which surfaces cannot be coated.

This preparation saves more time than subsequent adjustments. It helps immediately understand whether MN-088 or MN-094 is suitable for a specific frame, whether decorative and structural tasks are mixed up, and whether the bed can be assembled without random spacers, re-drilling, and reordering parts.

The final check should answer three questions: whether the design scheme of the supports is maintained, whether the actual height matches the calculation, and whether the leg pattern corresponds to the overall bedroom furniture. When all three answers are positive, the choice between MN-088 and MN-094 becomes justified and clear.

Before ordering, double-check the product cards.