Buy wooden sofa legs: turned MN-093 100 mm or geometric MN-072 180 mm — which to choose

Turned leg with decoration MN-148

from 16.47 $

Decorative leg MN-149

from 17.93 $

Turned leg with decoration MN-145.1

from 10.98 $

Turned leg with metal decoration MN-199

from 33.55 $

Precision leg with metal decoration MN-200

from 26.47 $

Turned Furniture Leg MN-178

from 30.25 $

Wooden Christmas balls SUV-002

from 12.32 $

Precision Furniture Leg MN-233

from 29.03 $

Go to Catalog

Why you should compare MN-093 and MN-072 before buying

Both models fit sofas, armchairs, ottomans, and other upholstered furniture, but provide different seating and different silhouettes. MN-093 with a height of 100 mm maintains a low profile and a soft classic line. MN-072 with a height of 180 mm raises the furniture by an additional 80 mm, increases the clearance under the body, and makes the base more geometric.

MN-093 — low turned support Height 100 mm helps maintain the usual seating position of a sofa, armchair, or ottoman and supports the classic silhouette.

MN-072 — high geometric leg Height 180 mm increases the clearance under furniture, makes cleaning easier, and more noticeably separates the body from the floor.

Height difference — 80 mm This changes the seat height, armrest position, and ease of getting up, so you cannot choose based only on a photo.

Beech for enamel or oak for tinting Both models allow you to choose an opaque paint or a finish with visible wood texture.

Different hardware for the bottom of the leg For MN-093, round glides FUR-022 and FUR-028 are suitable; for MN-072, the card specifies square FUR-023.

Short answer: For a low sofa, armchair, or pouf with a classic silhouette, choose the turned MN-093 with a height of 100 mm. If you need increased clearance under the furniture, easy cleaning, and a more modern geometry, the MN-072 with a height of 180 mm will work. Before ordering, you need to calculate the new seat height, check the existing frame, select the mounting and the foot cap.

Buy MN-093 100 mm Buy MN-072 180 mm

Buy sofa legs Choosing correctly means selecting not just a beautiful shape, but a new geometry for the entire piece of furniture. Replacing a low support with a high one changes the seating position, the clearance under the body, the load on the frame, and the perception of the sofa in the room. The MN-093 and MN-072 differ in height by 80 mm, so they cannot be considered interchangeable parts of the same size.

The turned MN-093, measuring 100 × 90 × 66 mm, is suitable for furniture that you don't want to noticeably raise above the floor. Its rounded shape pairs well with soft armrests, classic upholstery, capitoné buttons, and transitional interiors. The geometric MN-072, measuring 180 × 68 × 96 mm, works differently: it increases the clearance, adds straight lines, and helps visually lighten a massive body.

Both models are made from beech and oak without a finish coating. Beech is prepared for enamel, oak for tinting. However, the same choice of material does not make the legs identical in function. For the MN-093, the stud, FUR-001 and FUR-012 kits, and round foot caps FUR-022 and FUR-028 are confirmed. For the MN-072, the product card specifies a square foot cap FUR-023, matching the geometry of the lower part.

Watch video ...

Confirmed specifications for MN-093 and MN-072

The table shows product differences, but the final choice depends on the furniture. The leg height does not automatically equal the clearance height: part of the support may go into a decorative apron or mounting plate. Therefore, before purchasing, a side drawing of the body and an actual measurement of the old supports are needed.

Our factory also produces:

Turned Furniture Leg MN-145

from 6.59 $

Turned Furniture Leg MN-194

from 10.13 $

Precision Furniture Leg MN-143

from 240.20 $

Turned furniture leg MN-145.2

from 9.03 $

Turned Furniture Leg MN-195

from 73.56 $

Turned Furniture Leg MN-202

from 79.78 $

Precision Furniture Leg MN-179

from 33.43 $

Precision Furniture Leg MN-183

from 29.64 $

View Full Product Catalog

How is MN-093 different from MN-072

When to choose MN-093 with height 100 mm

For low sofa

MN-093 is suitable for a sofa whose seat already has a comfortable height and does not require a noticeable lift. The 100 mm leg keeps the body closer to the floor but does not make it visually heavy. It is especially appropriate for models with wide soft armrests, deep seating, and a rounded shape.

If the old supports were approximately the same height, replacing them with MN-093 will change the familiar ergonomics less. The user will not feel a sharp rise in the knees, and the armrests and backrest will remain at a familiar level relative to the body. But even in this case, you need to measure how much of the old leg went inside the frame.

For an armchair

For an armchair, the change in height is more noticeable than for a long sofa. A low turned leg helps maintain a stable silhouette and does not turn a compact item into a high chair on long supports. It is suitable for models with a soft back, rounded armrests, and classic upholstery.

For a chair, it is important to check how easily a person can stand up. If the seat is too low and the furniture is difficult to use, 100 mm may not solve the problem. Then you should consider MN-072, but only after calculating the new seat height.

For a pouf

A small pouf on MN-093 looks assembled and does not lose its compact feel. The round turned shape pairs well with a soft square or rounded body. The height of 100 mm provides a small gap, sufficient for manual cleaning, but not always for a robot vacuum cleaner.

If the pouf is used as a footrest, it is important not to raise it above the sofa seat. MN-093 more often allows maintaining the correct ratio. For a bedside pouf, the height is compared to the mattress and the top of the bed.

For a bench

A short bench on turned legs acquires a classic character and remains visually stable. The model is suitable for a hallway, bedroom, or dressing room, where the furniture should be neat and not look too tall.

When calculating a bench, the thickness of the soft block must be considered. If the frame, foam, and upholstery already provide significant height, 100 mm helps maintain a comfortable seating position. A too-high support in such a project would force a person to sit higher than the usual level.

For classic and transitional interiors

The rounded turned shape complements the soft lines of furniture, wooden handles, paneled fronts, and traditional fabrics. At the same time, MN-093 does not look overly decorative: it can also be used in transitional interiors where classic details are combined with a modern frame.

When it is important not to raise the seat too high

If the sofa is already comfortable in terms of seating, a high leg can ruin the ergonomics. MN-093 is more practical when the goal is to replace old supports, refresh the appearance, and get a small clearance without radically changing the furniture.

For such a scenario, you can buy sofa legs MN-093 and pre-select round glides and top mounting brackets.

When to choose MN-072 with a height of 180 mm

For a high clearance under the sofa

MN-072 raises the frame more noticeably. The 80 mm difference compared to MN-093 is felt both visually and functionally. There is more air under the sofa, the furniture appears lighter, and the floor becomes more accessible for cleaning.

However, the clearance cannot automatically be considered 180 mm. Part of the leg may be covered by the apron, decorative frame, or lower body panel. The actual size is measured from the floor to the lowest part of the furniture after installation.

For cleaning with a robot vacuum

A high support is often chosen for a robot vacuum. Before ordering, you need to measure the height of the specific device, taking into account the protruding sensor. Add a small margin to this value. Besides height, the width of the passage between the legs and the absence of a low central apron are important.

MN-072 can provide sufficient clearance, but by itself does not guarantee passage. The robot may be hindered by central supports, cables, an uneven carpet, or a protruding lower frame.

For modern and geometric furniture

The straight edges of MN-072 support a minimalist sofa, a chair with a clear outline, and a bench without complex carving. This leg pairs well with smooth upholstery, solid fabrics, and a simple-shaped body.

In a modern interior, geometry helps connect the sofa with the straight lines of tables, cabinets, and doors. If the rest of the furniture is built on rounded turned supports, MN-072 may look separate and require the shape to be repeated in another piece.

For visually lightening a massive body

A tall leg separates a heavy sofa from the floor and shows more space underneath. This is especially useful in a small living room, where a massive body on a low base visually takes up more space.

But lightness should not come at the cost of stability. The higher the support, the stronger the lateral force acting on the fastening when sitting on or moving the sofa. The frame must be checked and reinforced before installation.

For a bench in the hallway

MN-072 is suitable for a bench with a thin soft block and a modern shape. A height of 180 mm may be convenient if the frame is low. In the hallway, increased clearance makes cleaning easier, but the final seating height should remain comfortable for putting on shoes.

For a chair that is easier to get up from

A tall support can increase the seat height and make standing up easier. However, an additional 80 mm is a significant change. If a person is short, their feet may no longer rest firmly on the floor. Calculation is needed for the specific chair and user.

For increased clearance, you can buy wooden legs for the sofa MN-072, but only after checking the seating and frame.

How changing the leg height will affect the fit

Seat height

If you replace MN-093 with MN-072 without changing the frame, the top of the seat will rise by approximately the difference between the supports, taking into account their installation depth. This could be close to 80 mm, but the exact value depends on the installation. For upholstered furniture, such a change is significant.

A high seat helps some people get up more easily, but can be uncomfortable for children and shorter users. A low seat provides a relaxed sitting position, but requires more effort to stand up. The choice should not be made solely for appearance.

Foot position

On a comfortable sofa, feet rest on the floor and knees are not raised too high. After installing MN-072, legs may feel less stable. Before ordering, it is helpful to temporarily raise the existing sofa on rigid blocks 80 mm high and evaluate the seating.

Armrest height

The armrests rise together with the body. Their height relative to the seat does not change, but the entire composition changes relative to the coffee table, window, and adjacent chair. The old table may turn out to be too low.

Backrest position

The backrest becomes higher relative to the wall and pictures. If the sofa is under a window, the top may get closer to the windowsill. This should be checked before replacing the legs.

Bench seating

A bench often has a firmer seat and is used for putting on shoes. An additional 80 mm may make it too high. For MN-072, the frame and soft block should be designed from scratch, rather than placing legs on a ready-made high bench.

Coffee table position

After raising the sofa, the table may seem lower and less convenient. If legs are changed in an existing living room, compare the new seat height with the table, ottoman, and armchairs.

How to choose sofa legs based on actual clearance

Clearance is measured from the floor to the lowest fixed part of the body. A leg may be tall, but a low apron or central support will reduce usable space. For a robot vacuum, not only the centimeters at the edge matter, but also the entire route under the furniture.

Measure the old sofa

Measure the height of the old leg, its insertion depth, and the current clearance. Then add the difference between the old and new support. This calculation is more accurate than simply comparing 100 and 180 mm.

Check the central part

Long sofas often have hidden central legs or cross members. If the edge of the body is raised but the middle remains low, the robot still won't pass.

Consider the carpet

A thick carpet reduces the actual clearance and can interfere with the foot pads. If the sofa partially stands on the carpet, the supports must be in the same plane.

Make a full-size layout

Raise the furniture on temporary rigid supports to the intended height. Do not sit on an unsafe mockup if it is not designed for load. For visual assessment, a photo and checking adjacent items are sufficient.

Application of MN-093 and MN-072 in different furniture items

Sofa in the living room

MN-093 maintains a low, cozy fit and suits a classic sofa. MN-072 makes the frame lighter and more modern, but requires reconsidering the height of the table and armchairs. In a unified soft seating group, it's better to coordinate the legs in shape or at least in finish.

Chair

For an armchair, MN-093 provides a compact silhouette. MN-072 can ease getting up if the seat height was insufficient. However, a longer leg is more visible from the side and becomes an important part of the design.

Bench

A turned support suits a classic upholstered ottoman. A geometric one suits a modern piece with a thin seat. For a long body, the number of legs is calculated separately.

Pouf

MN-093 is usually a better fit in scale. MN-072 can make an ottoman look like a high stool and change its function. For a footrest, a tall model is usually less comfortable.

Hotel furniture

In a commercial project, a test sample is first assembled. The seating of different people, cleaning, glides, and the condition of the fasteners after intensive use are checked. Only then is the series ordered.

Children's room

A high sofa or armchair can be uncomfortable for a child. Additionally, the space under the furniture becomes a place for toys. For a children's room, a moderate height is usually more suitable, but the decision depends on the age and design.

Hallway

A bench on MN-072 is convenient for cleaning if the final height does not exceed a comfortable one. MN-093 gives a more stable and compact look, especially in a narrow room.

Cabinet

A lounge chair on MN-093 looks substantial and soft. MN-072 suits laconic furniture but must match the height of the side table and work area.

Beech for enamel or oak for tinting

Beech for opaque color

Beech legs are chosen when the supports should be white, black, gray, or painted to match the body. The enamel preparation allows for differences in lamellas, which will be hidden by the opaque coating.

On MN-093, the enamel emphasizes smooth turned transitions. On MN-072, it makes the edges more strict. The same color will be perceived differently due to the shape.

Oak for visible texture

Oak legs are suitable for tinting and transparent finish. The porous texture is well visible on MN-072 and softens its geometry. On MN-093, the pattern wraps around the rounded surface and creates a more classic look.

Matching the floor

Legs do not have to exactly match the floor color. Dark supports on a light floor make the furniture more graphic, light on dark make it lighter. If shades are close, it is better to compare real samples to avoid almost matching but conflicting tones.

Matching the body

Enamel allows painting the legs to match the color of the wooden frame or decorative apron. For oak, you can choose a close tint, but natural wood will still have differences.

Ordering in one batch

It's better to order four, five, or six legs at the same time. This makes it easier to match the wood, sanding, and finish. For a series of sofas, it's useful to order a spare support from the same batch.

If neither 100 nor 180 mm are suitable, you can Buy wooden furniture legs choose a different height and shape from the category of unpainted supports.

How to choose the number of legs

Four legs

Four supports are suitable for an armchair, pouf, compact bench, and small sofa with a rigid frame. They are located at the corners of the load-bearing frame, not at the edge of the decorative upholstery. All mounting points must be in the same plane.

For MN-072, the distance between legs is especially noticeable. Tall legs show body misalignment more, so marking must be precise. MN-093 visually forgives smaller deviations, but wobbling remains a functional issue.

Five legs

A central fifth support can support the middle of a small sofa. It should have the same effective height as the corner legs, taking into account the foot pad and mounting depth. On uneven floors, the central leg sometimes takes too much load or, conversely, does not touch the surface.

Six legs

For a long sofa or bench, six legs are often considered: four at the corners and two closer to the center. This helps reduce deflection of the bottom frame, but the extra legs should not interfere with the robot vacuum cleaner or the user's feet.

Eight legs

A very long modular sofa may require more support points or an internal frame. Simply adding legs without calculation does not always help: each leg must transfer the load to the supporting structure.

Why you cannot divide the weight equally

A person sits on the edge, a child jumps on the cushion, someone leans on the armrest. The load is distributed unevenly. The structure must withstand the worst-case scenario, not just the static weight of an empty sofa.

Spare leg

For a hotel, salon, office, or a series of identical sofas, it is useful to order a spare. Wood and tinting have natural variations, so a replacement from the same batch will be less noticeable.

How to attach legs to a sofa or armchair

Installation begins not with drilling, but with checking the frame. Under the upholstery there may be a solid frame, plywood, chipboard, or a combination of materials. The fastener must go into the load-bearing part and not rely only on a thin bottom or decorative fabric.

Stud and insert nut

For MN-093, the card specifies an M8 × 60 stud and a FUR-001 kit. FUR-001 consists of a stud with threaded and metric parts and a metal insert nut M8 × 13. The insert nut is installed into a prepared mounting hole in the frame.

This node is convenient for a removable leg, but requires a dense material. If the sofa base is made of a thin slab, a separate wooden insert is needed. For a suitable design, you can buy the FUR-001 mounting kit.

Round mounting plate

FUR-012 contains an M8 × 60 stud and a round mounting plate with a diameter of 37 mm. The plate requires a flat surface and its own attachment to the frame. It should not intersect with furniture staples, upholstery, or a decorative apron.

If the frame allows for a separate platform to be installed, you can buy the FUR-012 mounting kit and include its position in the drawing.

Marking

The leg axes are positioned symmetrically relative to the body. First, mark the centers, then check the distance to the edge, internal partition, and other fastenings. An error at one point will cause the leg to rotate or have uneven overhang.

Reinforcing a weak frame

Old furniture often has damaged holes and delaminated boards. A new leg will not fix a weak base. The damaged area is reinforced with an insert or repaired according to a furniture maker's design.

Installing the tall MN-072

For MN-072, the provided diagram does not specify a separate top kit. This does not mean the leg can be attached with a random screw. The connection method must be checked against the product drawing, mounting location, and frame construction.

Post-assembly inspection

Place the sofa on a level floor without load, check for wobbling and the position of all supports. Then gradually load the center and edges. If play appears, look for the cause in the fastening or frame, rather than masking the issue with different thickness glides.

What glides are needed for MN-093

Round FUR-022

FUR-022 has dimensions 30 × 30 × 5 mm and comes with a universal galvanized self-tapping screw 3.5 × 20. The furniture glide belongs to the SUPER GLIDE series and is designed for easier movement of furniture across the floor surface.

It fits the round bottom part of MN-093 in shape. However, the characteristic 'without damaging the floor surface' refers to the stated purpose of the glider itself, but before installation, the specific flooring, cleanliness, and furniture weight should still be checked. For such a combination, you can buy the round furniture glide FUR-022.

Felt FUR-028

The FUR-028 card calls it a felt furniture glide with a diameter of 28 mm; the size table indicates 25 × 25 × 5 mm. It comes with a universal self-tapping screw 3.5 × 20. The felt softens contact and is suitable for situations where furniture is periodically moved slightly on a hard floor.

For parquet and laminate, you can check out the felt furniture glide FUR-028, but its condition needs to be checked regularly: sand and debris in the felt can scratch the coating.

How to choose between FUR-022 and FUR-028

FUR-022 focuses on sliding and moving heavy structures. FUR-028 provides a soft felt contact. The choice depends on the floor, sofa weight, and frequency of movement. For a permanent stationary position, it is enough to protect the end and the floor; for periodic rearrangement, controlled sliding is more important.

Which glide is needed for MN-072

Square FUR-023

FUR-023 has dimensions 25 × 25 × 5 mm, is installed under a self-tapping screw, and comes with a universal galvanized self-tapping screw 3.5 × 20. The square shape matches the geometry of MN-072 and does not create a random round element on a straight bottom edge.

The glide belongs to the SUPER GLIDE series and facilitates the movement of heavy structures. For a high support, you can buy a square glide FUR-023, having checked the position of the screw and the thickness of the lower part of the leg.

Why the shape of the glider is important

The glider must fully rest on the wood and not protrude beyond the edge. A too large round element on a square leg will be noticeable and may catch. A too small one will reduce the contact area.

Effect of the glide on height

A thickness of 5 mm is added to the effective height. For one leg this is minor, but all supports must have identical gliders. You cannot place felt only on the two front legs if it changes the plane of the furniture.

Glides for parquet, laminate, tile, and carpet

Parquet and solid wood flooring

Soft contact is useful, but felt must be kept clean. A grain of sand turns the protective layer into an abrasive. A heavy sofa can leave point marks even through a glide, so the contact area and the condition of the covering are checked.

Laminate

On laminate, cleanliness, even joints, and the absence of protruding screws are important. A sliding glider is convenient for small movements, but the sofa should not be regularly rolled around the room.

Tile and porcelain stoneware

Hard floors are less prone to dents, but seams create unevenness. The foot may hit the edge of the tile. When moving a heavy sofa, it's better to lift it slightly.

Carpet

Felt and sliding covers may lose their purpose on soft pile. The leg sinks into the carpet, and the useful clearance decreases. If the sofa partially stands on carpet, all supports must have the same height relative to the floor.

Robot vacuum cleaner

The tall MN-072 can ease passage, but the glide, carpet, and soft underlay slightly reduce clearance. Measure the finished assembly, not just the height of the wooden part.

What to buy together with sofa legs

The kit starts with identical legs, but without fasteners and feet, it's not ready for installation. For MN-093, you need to choose FUR-001 or FUR-012 in advance, then round FUR-022 or felt FUR-028. For MN-072, check the top assembly against the frame and add square FUR-023.

If you need a wider selection of connections, you can Buy hardware for furniture legs in the profile category and compare available elements by size.

How not to confuse MN-093 and MN-072 with similar solutions

Low leg and furniture glider

MN-093 is a full-fledged wooden support 100 mm high. The glider is a small fitting installed at the bottom to protect the floor. It does not replace the leg and cannot increase the clearance by tens of millimeters.

High leg and decorative block

MN-072 has a geometric shape and precise dimensions, but is not a random wooden block. The furniture leg has finished surfaces, a commercial scenario is provided, and a square glider is selected. A homemade blank without wood inspection and fitting may crack or deform.

Turned and carved support

MN-093 is created by turning and has smooth repeating diameters. A carved leg usually contains ornamentation, leaves, or complex relief. For a soft sofa, the turned shape is calmer and easier to combine with upholstery.

MN-072 and angled leg

Geometric shape does not automatically mean tilt. The orientation of MN-072 must be checked according to the drawing. The leg cannot be installed at an arbitrary angle for the sake of a "modern look" if the mounting area is not designed for such a scheme.

Sofa leg and cabinet support

The same height does not make the products interchangeable. A sofa experiences dynamic load when sitting, while a cabinet experiences constant vertical load and risk of tipping. The frame construction and number of supports differ.

Glide and adjustable support

FUR-022, FUR-028, and FUR-023 are not claimed as height adjustment mechanisms. They protect the floor and aid movement. An uneven frame cannot be leveled by installing different gliders.

Practical selection for specific situations

Need to replace the broken legs of an old sofa

Remove one intact support and measure its total height, thread, insertion depth, and distance from center to edge of the body. Then open the technical fabric and check the insert. If the old leg was about 100 mm, MN-093 will provide a more predictable replacement. MN-072 will radically change the seating and require reinforcement.

Need to raise the sofa for a robot vacuum cleaner

First, measure the height of the robot. Then determine the lowest part of the body and the height of hidden central supports. MN-072 is more suitable, but only if all elements are raised to the same level and there is enough width between the legs.

Need to preserve the classic sofa

The turned MN-093 features rounded armrests, carriage stitching, and a traditional silhouette. The beech model can be painted to match the visible frame, while the oak model can be tinted to match the wooden details of the room.

Need to modernize a heavy body

MN-072 lifts the furniture off the floor and adds straight lines. This technique helps visually update a massive sofa without a full reupholstery. However, a high base will not fix a weak frame and may increase its wobbling.

Need to make the chair more comfortable for an elderly person

A higher seat sometimes makes standing up easier. Conduct a temporary test by raising the chair on a stable platform to the desired height difference. Feet should remain on the floor, and armrests should assist in standing up. If 80 mm is too much, look for an intermediate model in the category.

Need to assemble a pouf for the sofa

The top of the ottoman is usually placed at or slightly below the seat level of the sofa. MN-093 is easier to fit into this task. MN-072 is only suitable with a very thin body and a different function, such as a high bench.

Need to replace the legs on only one chair in the set

The new shape should match the sofa and the second armchair. If the other items have rounded supports

Need upholstered furniture for a hotel

Make a test item. Check the height for people of different heights, cleaning, fasteners, and glides. For the series, record the article, wood species, sanding, finish, and number of supports. It is better to order spare legs together with the main batch.

Need to update furniture without full disassembly

If access to the inner frame is blocked, a quick replacement may be impossible. Do not attach the mounting plate to a single thin panel. Sometimes proper repair requires removing the technical fabric, installing embedded parts, and only then assembling the unit.

Mistakes when buying legs for a sofa

Choosing only by photo

On the card, MN-093 and MN-072 are shown separately, without the full sofa. The 80 mm difference is easy to underestimate. Draw the legs to scale or make a cardboard template next to the body.

Ignoring the old height

If the previous support was 50 mm, even MN-093 will raise the furniture. If 150 mm, MN-072 will change it less. You need to compare with the current part, not just the two new models with each other.

Not accounting for insertion depth

Part of the leg or stud goes into the frame. The visible height may differ from the product height. The drawing and installation method determine the actual clearance.

Buying four legs for a long sofa without checking

The middle of the body may sag. Need to find old central supports and keep the calculated number of points.

Installation in weak particleboard

A high leg creates significant leverage. A threaded insert in a thin, loose board can tear out. A rigid wooden or plywood insert is needed.

Random choice of mounting for MN-072

The model card confirms FUR-023 as the lower foot pad, but does not grant the right to transfer MN-093 fastenings. The upper assembly needs to be verified against the drawing and with a specialist.

Missing glides

The end grain of the wood gets dirty faster, and the floor gets point contact. For MN-093 and MN-072, there are confirmed glides of the corresponding shape.

Different foot pads on the same sofa

Thickness and slip must match. If the front legs slide and the back legs catch, the frame gets skewed during movement.

Beech for clear finish without accounting for regluing

Beech prepared for enamel, so slats may differ in color and texture. For visible wood, it is more rational to choose oak for tinting.

Oak for dense enamel without necessity

Opaque painting hides the advantage of oak texture. If a solid color is needed, beech usually matches the task more accurately.

Installing MN-072 for a robot without measuring the central crossbar

High outer legs won't help if the middle of the sofa remains low. Measure the entire path under the frame.

Painting after installation on the sofa

Enamel may get on the upholstery, fittings, and glides. It is more convenient to finish the legs separately, keeping the threads and mounting surfaces clean.

Moving a heavy sofa by the armrest

Even sliding glides do not turn furniture into a mobile platform. The sofa is moved with the participation of several people, without creating lateral load on high legs.

Who MN-093 is for

The turned model is suitable for the owner of a low sofa, armchair, ottoman, or bench who values a classic or soft shape. It is useful when replacing old supports of similar height, when you don't want to change the seat height by 80 mm.

MN-093 is also convenient for a craftsman who wants to use proven FUR-001 or FUR-012 kits and choose a round or felt glide. The model works well under enamel and tinting if the wood species is chosen correctly.

Who is MN-072 suitable for

The geometric model is suitable for a new sofa or bench where the height of 180 mm is built into the design. It is useful for increased clearance, a modern shape, and visual lightening of the body.

MN-072 is worth considering if you need space for a robot vacuum cleaner and the thin body allows you to maintain a comfortable seat height. A high leg requires rigid fastening and careful checking of lateral load.

When it's better to choose a different model

If 100 mm is too little and 180 mm is too much, there is no need to cut or extend ready-made legs. The STAVROS category has other sizes and shapes. An intermediate height often solves the problem better than a compromise with an uncomfortable seat height.

A different model is also chosen when the sofa needs an angled support, a metal base, height adjustment, or a hidden structure. MN-093 and MN-072 have a specific wooden character and should not be used outside a suitable project.

Preparing beech for enamel

Grinding check

MN-093 is supplied with 'Prestige' quality. For MN-072, you can choose 'Standard' or 'Prestige'. Before priming, each surface is inspected under side lighting and dust is removed.

Thread and fit protection

Primer and enamel must not get into the threaded joint or onto the surface that contacts the frame. A thick layer can create misalignment between the legs.

Priming

Use a compatible system for wood. On the turned MN-093, watch for runs at diameter transitions. On MN-072, ensure evenness on edges and corners.

Finish color

White legs visually lighten the sofa, black legs make the support graphic, colored legs tie the furniture to the upholstery. One set is painted simultaneously and under identical conditions.

Oak preparation for tinting

Test paintout

Staining looks different on end grains and longitudinal fibers. MN-072 has pronounced planes, MN-093 has a rounded surface. The sample should be evaluated on a shape close to the selected leg.

Matching with gender and furniture

Oak can be made lighter, darker, or close to the body. An exact match with the parquet is not necessary. It is better to create a deliberate contrast than to get two almost identical shades.

Protective finish

After tinting, the wood is protected with a compatible varnish, oil, or other approved system. The bottom end and attachment points are treated considering the base plate and threads.

How to accept legs after delivery

Check the article numbers and sizes

MN-093 — 100 × 90 × 66 mm, MN-072 — 180 × 68 × 96 mm. Check the quantity and selected wood species before finishing.

Check one batch

Compare the shade and wood grain. Natural differences are acceptable, but for one sofa, the parts must form a coordinated set.

Inspect the seating areas

The top part must not have damage that interferes with fastening. Before drilling, attach the hardware and ensure it matches the project.

Check the glides

Count FUR-022, FUR-028, or FUR-023 by the number of supports. Screws must match the kit. Do not mix different types without calculation.

Care for wooden legs and glides

Painted legs

Wipe enamel with a soft cloth and do not clean with abrasives. Remove shoe marks with a product compatible with the coating. Moisture should not remain at the bottom end for long.

Tinted oak

Care depends on the protective finish. Strong solvents may change the shade and gloss. Repair a damaged area with the same material system.

Felt glides

FUR-028 is regularly cleaned of sand and hair. Worn felt is replaced on all supports equally if the new thickness differs.

Sliding glides

FUR-022 and FUR-023 are checked for sharp debris and damage. The sofa is moved smoothly, not crossing thresholds.

How to buy MN-093 or MN-072 at STAVROS

Start by measuring existing furniture or a side drawing of the new sofa. Record the current seat height, old leg height, actual clearance, and position of center supports. Then compare two scenarios: maintaining a low seat with MN-093 and raising the body with MN-072.

Open the card of the selected model

For a turned leg, go to the MN-093 page and select beech or oak. For a geometric one, open MN-072, where you additionally choose the sanding quality "Standard" or "Prestige." Check the current price, availability, and delivery time directly before ordering.

Calculate the set

The number of legs must match the sofa design. Four supports are not suitable for every body. Check the center points, frame length, and partition placement. For a furniture series, add a spare leg of the same type and quality.

Add the fittings

For MN-093, select FUR-001 or FUR-012 based on the frame type and the foot pad FUR-022 or FUR-028 based on the floor and movement method. For MN-072, add FUR-023 and separately coordinate the top connection.

Coordinate the finish

Beech is bought for enamel, oak for tinting. Keep a sample of the color and finishing system. If the legs must match the existing body, compare the actual materials under room lighting.

Check the drawing

Before ordering, the master must confirm the axes, offsets, embedded parts, and seating depth. High MN-072 requires a particularly rigid joint. If there is insufficient data, it is better to clarify the parameters with the STAVROS manager and the furniture designer.

After checking, you can buy furniture leg MN-093 for a low sofa or buy furniture leg MN-072 for increased clearance.

What to Check Before Ordering

• current seat height;
• height and seating depth of the old leg;
• difference of 80 mm between MN-093 and MN-072;
• desired actual clearance under the body;
• height of the robot vacuum cleaner and its sensors;
• position of hidden central supports;
• length and rigidity of the lower frame;
• number of legs;
• presence of wooden or plywood embedded parts;
• top mounting method;
• FUR-001 or FUR-012 for MN-093;
• round FUR-022 or felt FUR-028;
• square FUR-023 for MN-072;
• floor covering type;
• beech for enamel or oak for tinting;
• MN-072 sanding quality;
• color of legs relative to floor and body;
• compatibility of new height with chairs and table;
• need for spare part;
• current order conditions in the card.

Quick selection guide for MN-093 or MN-072

Choose MN-093, if the sofa is already comfortable in height, a small gap is needed, the interior is built on rounded or classic lines, and the supports should be less noticeable. This model is better suited for a pouf, compact chair, and bench with a thick soft block.

Choose MN-072, if the furniture is being designed from scratch, it is necessary to noticeably raise the body, cleaning under the sofa is important, and the geometric shape supports a modern interior. First, check the fit, frame rigidity, and actual passage height.

Choose a different model, if 100 mm is not enough and 180 mm is excessive, tilt, adjustment, or a metal support is needed. In this case, it is useful to open catalog of unpainted furniture legs and select an intermediate option.

How to check a finished sofa after replacing legs

No-load check

First, place the sofa on a flat, hard floor and ensure all supports touch the surface. The body should not wobble when lightly pressed on different corners. If one leg is hanging, do not rush to add extra material: check the frame plane, uniform mounting depth, and glides.

Gradual loading

After the initial check, sit first in the center, then closer to the edge and armrest. Observe if any creaking, leg rotation, or gap between the support and frame appears. For MN-072, this check is especially important due to the increased leverage.

Simultaneous seating of multiple people

The sofa is designed for more than one user. Check the seating of two or three people in normal mode. The center supports must take the load without the frame sagging. If the middle noticeably deforms, the number and placement of legs require revision.

Opening the sleeping mechanism

If the sofa unfolds, replacing the supports should not change the mechanism's operation. Check the full transformation cycle, contact of the pull-out parts with the floor, and the height of the sleeping area. New legs may change the angle or position of the additional section.

Check near the wall

The tall MN-072 raises the backrest and armrests. Ensure the sofa does not block the windowsill, outlets, or wall decor. If the frame is pushed against the wall, the baseboard should not create a tilt.

Checking the robot vacuum cleaner

Run the device along the entire route under the sofa. It should pass not only at the front edge, but also between the central supports, under the frame, and near the wall. If the robot gets stuck, the tall leg did not fully solve the problem.

Inspection of fastenings after a few days

After the first days of use, remove the technical fabric or use the provided access and check the components. The wooden insert, threaded bushing, or plate should have no play. Early inspection helps eliminate slight loosening before damage to the frame.

How to coordinate the new sofa height with the rest of the living room

Coffee table

After switching from MN-093 to MN-072, the sofa becomes higher, and the old table visually and functionally lowers. A person has to bend over more. Compare the tabletop with the seat and armrest level before final installation.

Armchairs

If the sofa and armchairs form a set, different seat heights may look accidental. It is not necessary to use the same legs, but the top of the soft cushions and the armrest line should be coordinated.

Pouf

The ottoman should remain at or slightly below seat level. A high sofa on MN-072 may require a new support for the ottoman as well. Compact MN-093 often helps maintain the correct difference.

Floor lamp and side table

The raised body changes the user's position relative to the light and side surface. The lamp may end up below the shoulder, and the table may become uncomfortable. Evaluate the entire area, not just the clearance under the sofa.

Paintings and wall decor

The backrest rises after replacing the supports. The distance to the painting or shelf decreases. Before installing MN-072, it is useful to mark the new top line of the sofa on the wall with painter's tape.

Carpet

High legs show the carpet border more. If the front supports are on the carpet and the rear ones on the hard floor, the thickness difference creates a tilt. All points must have the same support plane.

How to save data for reordering

After successful installation, save the leg article, wood species, sanding quality, mounting type, footrest, and exact finish color. Add photos of the top assembly and the distance from the floor to the body. This information will be useful if you need to replace one part, make a second chair, or replicate the set for another room.

For the commercial series, create a brief specification for each item. It records the number of supports, the position of the central legs, the material of the inserts, and the installation procedure. Then the next sofa will not differ in height and stability from the first.

Before final ordering, it is useful to compare two temporary mockups. For MN-093, place rigid supports under the body that give the intended clearance of the low model. For MN-072, repeat the test with a height 80 mm greater. Compare not only the appearance but also how you sit, stand, use the table, and start the robot vacuum. Such a mockup is not suitable for full load if it is not designed for the weight of the sofa, but it shows the scale well and helps to abandon a wrong decision before purchase.

If the furniture is made to order, include the leg height in the overall drawing, rather than leaving the choice for the final stage. The designer will be able to correctly assign the lower apron, central supports, and inserts, the designer will coordinate the shape with the body, and the finisher will select enamel or tinting for the entire set. Joint verification in advance is more reliable than trying to fix a finished sofa with footrests of different thicknesses or random reworking of the mounting.

Frequently asked questions

How is MN-093 different from MN-072?

MN-093 is a turned leg 100 mm high, MN-072 is a geometric support 180 mm high. The difference of 80 mm affects the seating, clearance, style, and load on the mounting.

What are the dimensions of MN-093?

The model size is 100 × 90 × 66 mm. Before purchasing, compare the height with the existing leg and consider the depth of insertion into the frame.

What are the dimensions of MN-072?

The model size is 180 × 68 × 96 mm. The high support requires checking the overall seat height and the rigidity of the lower frame.

Which leg is better for a low sofa?

Mostly MN-093. It changes the seating position less and keeps the body closer to the floor. The final choice depends on the height of the old support.

Which model is best for a robot vacuum cleaner?

MN-072 provides a larger potential clearance. But you need to measure the lowest part of the sofa, the central supports, and the height of the specific robot.

Can I install MN-072 instead of a 100 mm leg?

Technically, this is only possible after recalculation. The seat will rise approximately by the height difference considering installation, and the lateral load on the mount will increase.

Can I install MN-093 instead of a high leg?

It can be considered if the reduction in clearance and seat height suits the user. Check that the apron does not drop too close to the floor.

What to choose for a classic interior?

The turned MN-093 usually blends more naturally with rounded armrests, tufted upholstery, and traditional furniture.

What to choose for a modern sofa?

The Geometric MN-072 supports straight lines and visually separates the body from the floor. It is especially appropriate for furniture with a thin, minimalist base.

Should I choose beech or oak?

Beech is prepared for opaque enamel. Oak is prepared for tinting and suits finishes with visible natural texture.

Can beech be painted white?

Yes. Beech for enamel is suitable for white, black, gray, or colored opaque finishes. Carving and mounting surfaces are protected from paint.

Can oak be left natural?

Oak is better protected with a clear or tinted finish compatible with usage conditions. Untreated wood gets dirty faster.

What sanding quality should be chosen for MN-072?

The card offers "Standard" and "Prestige". "Prestige" involves more detailed preparation, and the choice depends on the requirements for the future finish and the project budget.

Is there a choice of sanding for MN-093?

The current card indicates "Prestige" quality. Before ordering, you need to verify the selected configuration.

How many legs does a sofa need?

Four are suitable for a compact rigid frame. A long sofa may require five, six, or more supports. The center points must be preserved and the frame checked.

Is a central leg necessary?

If it was provided by the manufacturer or the middle of the frame is under load, it cannot be removed. The center support must have the same effective height.

How to attach MN-093 to a sofa?

You can use a confirmed stud, FUR-001, or FUR-012. The specific option is chosen based on the material of the embedded plate and the available mounting area.

Can FUR-001 be used in particleboard?

Thin or loose particleboard should not be considered a sufficient base. A rigid embedded plate made of solid wood or plywood is often needed.

How does FUR-001 differ from FUR-012?

FUR-001 uses a stud and a metal insert. FUR-012 includes a stud and a round mounting plate with a diameter of 37 mm.

How to attach MN-072?

The top attachment must be verified against the model drawing and sofa construction. FUR-001 or FUR-012 cannot be automatically transferred from MN-093.

Which glider is suitable for MN-093?

The card lists round FUR-022 and felt FUR-028. The choice depends on the floor, furniture weight, and the need for slight movement.

Which glider is suitable for MN-072?

For the model, square FUR-023 size 25 × 25 × 5 mm is confirmed.

Is FUR-028 suitable for parquet?

Felt contact is usually chosen for hard surfaces, but it must be kept clean. Sand in the felt can scratch parquet.

Can I move a sofa on FUR-022?

The glider is designed for easy movement of heavy structures. The sofa is still moved smoothly and does not cross thresholds.

Does the glider add height?

Yes. The confirmed FUR-022, FUR-028, and FUR-023 have a thickness of 5 mm. All legs must receive the same elements.

Will MN-093 fit a chair?

Yes, especially for a low classic chair. Check the fit, number of supports, and rigidity of the frame corners.

Will MN-072 fit a chair?

It can be considered if the chair needs to be raised and the user's feet remain on the floor. The high support will become a noticeable part of the design.

Which model is better for a pouf?

More often MN-093, because it maintains a compact height. MN-072 is only suitable for a thin body or high bench seating.

Can MN-072 be trimmed to an intermediate height?

Self-trimming may change the geometry and seating area. It is better to choose a ready-made model of the appropriate height in the category.

Do the legs need to be finished before installation?

It is usually more convenient to do a test assembly, then remove the legs, finish them separately, and install them after the coating has fully dried.

Where to buy MN-093 and MN-072?

Both models are presented in the STAVROS catalog with separate cards. Select the height, wood species, sanding, and accompanying hardware after checking the frame.

Summary: low turned MN-093 or high geometric MN-072

MN-093 and MN-072 solve one task — they create a wooden support for upholstered furniture — but are not interchangeable. The turned leg 100 mm maintains a low seat height and is suitable for a classic sofa, armchair, pouf, or banquette. The geometric model 180 mm increases clearance, facilitates cleaning, and creates a more modern silhouette.

The main difference is not just the 80 mm in height. The seat, armrest, and backrest positions change, as does the load on the frame, the choice of glides, and the sofa's relationship with the rest of the furniture. Before ordering, you need to measure the old support, check the center points, prepare the inserts, and determine the finish.

STAVROS allows you to go from comparison directly to a specific card: low sofa legs 100 mm will suit a restrained classic body, and high legs for sofa 180 mm — furniture with increased clearance and strict geometry. A conscious set with fastening and foot pads is more reliable than a random replacement based only on appearance.