Buy a coffee table base: spherical STL-035 or hemispherical STL-036 — which to choose

Buying a coffee table base seems like a simple task until two round models with completely different proportions are nearby. STL-035 resembles an elongated sphere with a truncated top: the base is taller, narrower in width, and looks like a separate sculptural support. STL-036 is built on a wide hemisphere: it is lower, more massive, more connected to the floor, and forms a more grounded silhouette. Both products are suitable for a modern accent table, but the tabletop, overhang, height, and placement near the sofa are calculated differently for them.

STL-035 has confirmed dimensions of 550 × 425 × 400 × 286 mm and a weight of 24 kg. STL-036 — 800 × 300 × 452 mm and 36.5 kg. Both models are made from glued MDF blanks with deep milling, have an internal cavity to reduce weight, "Prestige" sanding, and are supplied with one layer of primer-insulator for MDF. The surface can be painted with enamels of different colors. The cards allow the use of tabletops made of wood, glass, metal, and other materials, but the specific size, weight, and attachment method must be agreed upon for the chosen design.

The main mistake is choosing only between the words "ball" and "hemisphere." For a finished table, four questions are more important: how high the tabletop should be, how large its overhang will be, how wide the base rests on the floor, and whether the support should look like a lightweight art object or a massive architectural center. STL-035 raises the composition higher and leaves more air around the base. STL-036 visually spreads across the floor and better suits a large, low tabletop if the structure is confirmed by a drawing.

Below, we will analyze the models as a specific buyer's choice, not as a general overview of table bases. You will learn which base looks best in front of a sofa, what to choose for a round, square, glass, or wooden tabletop, how to assess stability, when one central base is enough and when two bases are needed, what finish to plan, and what to check before ordering from STAVROS.

Buy spherical table base STL-035 Buy hemispherical table base STL-036 View frames and table bases Choose a tabletop

Go to Catalog

How STL-035 differs from STL-036

Both models are central bases for a coffee table, made from deep-milled MDF and have a horizontal ribbed texture. This is where the similarity ends. STL-035 is 125 mm taller, while STL-036 is significantly wider in its main dimension and 12.5 kg heavier. These differences change not only the appearance but also the entire vertical and horizontal scheme of the future piece.

Dimensions should not be read as a ready-made recommendation for the tabletop. The numbers show the geometry of the underframe itself, but do not indicate the permissible diameter, thickness, or weight of the top part. Selection is made based on the drawing, actual top platform, center of gravity, attachment method, and operating conditions.

What is a central underframe and how it differs from individual legs

A central underframe supports the tabletop on one main support located closer to the geometric center. Unlike four legs at the corners, it frees up the outer perimeter, makes the silhouette integral, and allows the base to be considered as an independent form. For a coffee table, this is especially noticeable: the item is low, and the underframe is constantly in view.

The absence of corner legs does not automatically mean freedom for any tabletop. When pressed from the side, the edge creates leverage relative to the center. The larger the overhang, the higher the weight, and the smaller the support area, the more careful the stability check must be. A central base is convenient but must be coordinated with the top part.

STL-035 and STL-036 are already formed three-dimensional products. The buyer does not need to assemble a sphere from individual segments, carve knurling, or search for a random blank. The main work shifts to selecting the tabletop, finishing, and installation.

Such a pedestal is especially appropriate in designer furniture. It does not try to blend in under the tabletop like thin legs, but sets the character of the entire piece. Therefore, the shape of the base is chosen simultaneously with the interior, not after the tabletop has already been purchased.

Our factory also produces:

View Full Product Catalog

When to buy the spherical base STL-035

STL-035 is suitable when the table should look compact but expressive. The height of 425 mm makes the base itself close to the usual height of coffee furniture even before adding the tabletop. Therefore, the final vertical dimension must be calculated especially carefully: even a thin top part will increase the overall height.

The spherical silhouette works well in a small living room where you want an art object without a too wide base. The base occupies a noticeable space but does not spread across the floor as widely as STL-036. More visible space remains around it.

The model is suitable for a round tabletop if its diameter and mounting are confirmed by the project. A circle above a rounded base creates a calm axial composition. A square tabletop adds contrast: the soft sphere supports the rigid geometry of the upper plane.

For an accent table next to an armchair or in a lounge area, you can view the STL-035 underframe and download the drawing. Before ordering, compare the height of 425 mm with the sofa, armchair, and the thickness of the chosen tabletop.

STL-035 is also suitable for a pair of small tables of different heights, but using two identical bases under one long tabletop is only possible after calculation. A paired composition requires precise distance, identical installation, and verification of load distribution.

When to choose the hemispherical STL-036

STL-036 has a height of 300 mm and a wide dimension of 800 mm. It creates a grounded composition and leaves more space for the thickness of the tabletop if a low coffee table is required. The base is visually connected to the floor and looks like a wide architectural foundation.

The hemisphere is suitable for a large living room, spacious seating area, hall, showroom, or lounge space. At a significant distance, STL-036 does not get lost: the wide ribbed surface remains readable and supports a large tabletop in scale, but does not automatically confirm its permissible size.

The model is especially expressive under a round tabletop, when the upper circle and the hemisphere form a concentric composition. With a square top, a stronger contrast appears, and the corners increase the actual overhang relative to the central support. This scenario requires careful stability verification.

For a buyer who needs the central base STL-036, they should assess the passages around the table in advance. The wide base takes up more floor space and may be too large for a narrow area between the sofa and the TV cabinet.

The weight of 36.5 kg helps the base feel massive and stable, but it is not a guarantee of the finished table by itself. The final result depends on the tabletop, fastening, overhang, and the nature of the load.

Ball or hemisphere: how visual mass changes

STL-035 is perceived as more vertical. The gaze travels from the floor to the top platform along the rounded shape, and the base looks almost like a large bead or an independent sculpture. It is noticeable but retains air around it.

STL-036 is perceived as more horizontal. The wide bottom line and lower height connect the object to the floor. This base makes the table visually heavier and calmer, especially in a large room.

Light enamel enhances the difference. STL-035 becomes more graphic and light, STL-036 resembles an architectural dome. Dark coloring increases the sense of mass in both models, but the wide hemisphere reacts more strongly.

Horizontal fluting further expands the silhouette. On STL-036 it supports width, on STL-035 it balances vertical height. Directional light emphasizes the grooves, so the base should be evaluated in future lighting.

How to choose the height of a coffee table

The final height equals the height of the underframe, the thickness of the tabletop, and the actual addition of the mounting assembly. For STL-035, the initial height dimension is 425 mm, for STL-036 — 300 mm. Even without precise recommendations, it is clear that the models solve different vertical tasks.

STL-035 with a thick tabletop can provide a relatively tall coffee or side table. If the surface should be noticeably lower than the sofa seat, you need to check whether the base will be too high. STL-036 leaves more room for a massive top part.

It is not worth relying only on the average furniture height. Measure the seat, armrest, and the usual usage area. A table for a book and decor can be lower, for a cup and laptop — higher.

A detailed general route is revealed in the article about choosing the height of a coffee table base. In a specific comparison, the choice starts from 425 or 300 mm and continues with the actual thickness of the tabletop.

Round tabletop: the most natural scenario

The circle repeats the rounded geometry and does not create corners with increased diagonal overhang. This makes the composition visually calm, but does not negate the overhang calculation. Even a round tabletop can be too large or heavy for a specific base.

STL-035 gives a more vertical silhouette: the top seems to balance on a ball. STL-036 creates the feeling of a wide support with a disc above it. The first option is more dynamic, the second is more stable in perception.

For a small room, a round shape is convenient due to the absence of sharp corners and smooth navigation. However, STL-036 itself has a dimension of 800 mm, so the overall width needs to be compared with the walkways.

Before ordering, cut a circle out of cardboard in the intended size, place it on a temporary mock-up of the appropriate height, and evaluate it next to the sofa. Such a test shows the actual walkways and scale.

Square tabletop: contrast of soft and rigid geometry

The square enhances the design character of the base. A ball or hemisphere becomes a soft center under a strict plane. This looks especially expressive in modern classics, art deco, and eclecticism.

Corners create maximum diagonal overhang. If you press on the edge, the lever relative to the central support is higher than that of a circle of the same nominal size. Therefore, a square cannot be chosen only by width.

STL-035 is suitable for a small square table when you want to emphasize contrast and maintain free space around it. STL-036 requires a large scale, otherwise the base may extend almost to the edges of the tabletop.

The fastening must prevent rotation of the top part and account for the arrangement of fibers or layers of the material. The scheme is coordinated with the furniture maker.

Glass tabletop: the base is fully visible

The glass does not hide the underframe, so the fluting, primer, finish, and top platform become part of the visible composition. STL-035 under glass looks like an independent sculpture, STL-036 like a wide dome.

Attaching glass differs from attaching a wooden tabletop. Random screws cannot be used. The connection method, thickness, tempering, edge treatment, and size are determined by a specialist.

A transparent surface highlights dust and marks on the base. The ribbed form should be cleaned with a soft brush or cloth, without damaging the enamel.

If the glass is tinted or frosted, the base reads differently. Color and material samples should be considered together.

How the base shape influences the choice of tabletop

Category helps choose a tabletop for a coffee table, but no item becomes compatible automatically. First, select the base, then match the drawings, weight, thickness, mounting area, and expected load.

Wooden tabletop and MDF

A wooden top adds natural texture and can contrast with a painted base. A dark tabletop over a light sphere makes the base graphic, while a single color creates a monolith.

Solid wood changes dimensions with humidity changes, so the fastening must account for the material's properties. A large wooden tabletop cannot be rigidly fixed without a suitable joint.

An MDF tabletop is convenient for solid-color enamel and precise geometry. It can be painted the same color as STL-035 or STL-036, creating a unified piece.

The thickness of the top affects the final height and visual balance. STL-035 already has a height of 425 mm, so a massive tabletop may make the piece too tall. STL-036 more easily accepts a thick top proportionally, but this is not a structural guarantee.

How to calculate the tabletop overhang

Overhang is the distance from the edge of the base or upper support zone to the edge of the tabletop. For a central pedestal, it affects appearance, convenience, and stability. The larger the overhang, the stronger the lateral leverage when pressure is applied.

The overhang cannot be calculated only from the largest dimension of the body. The actual top platform, contact shape, fastening method, and center of mass are important. Use the product drawing.

For a round tabletop, the overhang is uniform around the circumference if the centers align. For a square one, the maximum projection is along the diagonal. For a rectangular one, check the long and short sides separately.

Before ordering, make a template of the tabletop and mark the outline of the underframe on it. Then assess where cups, books, and possible hand pressure will be. After visual inspection, the calculation is confirmed by the designer.

How to check the stability of a finished table

Stability depends on the contact area with the floor, center of gravity height, base mass, tabletop dimensions and mass, attachment quality, and load distribution. No single parameter works in isolation.

STL-036 is wider and heavier, so it feels more stable. However, a very large tabletop with excessive overhang can make the structure unsafe. STL-035 is more compact and taller, so it requires particularly careful checking of lateral load.

During dry assembly, place the table on a level floor and press on the edges in different directions in a controlled manner, without exceeding the design load. Check for wobbling, rotation of the tabletop, and contact of the base with the floor.

If the table will be used in a hotel, restaurant, or showroom, more intensive use must be considered. Visitors may lean on the edge, move the furniture, and place heavy objects.

One base or two

A single central underframe is natural for a round, square, or compact oval tabletop. It maintains a clean silhouette and a free perimeter.

A long rectangular or oval tabletop may require two bases. STL-035 is more convenient in scale for a paired composition, but the distance and quantity are determined by calculation. Two STL-036 units form a very massive base and require a large area.

Paired pedestals must be installed at the same height and along a common axis. The top should not sag between them. Fasteners are placed symmetrically.

Do not use two bases solely for appearance without checking the mass and geometry. An additional support changes the load distribution and may cause wobbling on uneven floors.

Pedestal near the sofa

A table in front of the sofa should leave a passage and be accessible from the seat. STL-035 takes up less floor space and may be more convenient in a compact living room. STL-036 suits a spacious seating group where a wide base does not interfere with legs and movement.

The height is compared with the seat and armrest. STL-035 already has 425 mm to the tabletop, STL-036 has 300 mm. The first option may be close to the upper limit of coffee furniture, the second allows for a very low piece.

When choosing, consider the sofa depth and typical actions: placing a cup, putting down a book, reaching for the remote. A beautiful table should not force constant bending or block the passage.

On a carpet, a wide hemisphere is perceived differently than on a hard floor. Check whether the base sinks into the pile and whether the table remains stable.

Small and large living room

In a small room, STL-035 often looks more proportional due to its smaller main dimension. The spherical shape remains noticeable, but passages are preserved around it. At the same time, the base height of 425 mm requires a particularly thin or moderate tabletop if a classic low coffee table is needed.

STL-036 requires space. The dimension of 800 mm along one of the base axes is already comparable to the width of a small coffee table. In a narrow room, the hemisphere can visually occupy the entire center and reduce the distance to the sofa, armchairs, or TV cabinet.

In a large living room, STL-035 can be used as a single compact accent or a pair of separate tables. STL-036 better holds scale in front of a long sofa and in a group of several armchairs, where a small base could get lost.

Room area is not the only criterion. Look at the sofa length, rug size, armrest height, distance to walkways, and the amount of other furniture. Sometimes a spacious room is so densely filled that the compact STL-035 turns out to be more precise.

Living room, bedroom, study, and commercial interior

In the living room, both models become the center of the soft seating group. STL-035 suits a lighter composition and a table that can be visually separated from the rug. STL-036 forms a large low center and more strongly ties the furniture around it.

In the bedroom, STL-035 can be used as an accent table near an armchair, window, or bench if the final height is suitable. STL-036 requires more free floor space and is more appropriate in a large master bedroom with a separate lounge area.

In a study, the spherical base softens strict furniture and adds a rounded shape next to straight cabinets. The hemisphere forms a representative lounge table for the informal part of negotiations.

In a showroom, hotel lobby, salon, or restaurant, STL-036 is better read from a distance, while STL-035 allows creating several compact points. For commercial use, the load, finish, and method of movement are agreed upon separately.

Coffee, side, or accent table

A coffee table is usually placed in the center of the soft seating group. A side table can be closer to an armchair and have a higher surface. An accent table serves a specific spot and often has a smaller tabletop. STL-035 is closer to a tall accent scenario, STL-036 to a low central one.

You cannot change the purpose just by the name. If STL-035 with the chosen tabletop ends up higher than the armrest, it may be inconvenient as a central coffee table but work well next to an armchair. STL-036 may be too low for a daily cup, yet effectively supports books and decor.

An accent table allows for a bolder shape and color because its function is not limited to storing items. The fluted base becomes part of the interior design scenario.

Before ordering, write down the three main tasks of the table. If daily use is a priority, ergonomics are more important than a striking shape. If the item is needed as a central art piece, a more expressive proportion is acceptable.

How to combine the base with a sofa and armchairs

A round tabletop softens a straight modular sofa well. STL-035 adds one vertical spherical shape, STL-035 creates a wide horizontal support and visually extends the seat line.

The round sofa STL-035 supports plasticity, but can create too many similar shapes if the tabletop is also small and round. STL-036 more strongly emphasizes the soft geometry of the entire area.

Armchairs with thin legs pair better with compact STL-035 if lightness needs to be preserved. Massive low armchairs and a deep sofa can handle a wide hemisphere.

The base color can be tied to the upholstery, case furniture, or wall. It is not necessary to repeat the exact shade of the sofa. Sometimes a neutral enamel helps the tabletop and textiles become the main focus.

How to combine the base with the rug and floor

The rug defines a separate plane under the coffee table group. The spherical STL-035 leaves more visible rug surface around itself. The hemisphere occupies a significant area and becomes the visual center of the pattern.

On a rug with long pile, you need to check the base contact and stability. A wide base may sink unevenly, while a compact one presses on a smaller area. The specific result depends on the floor and rug material.

On stone, tile, or parquet, the base is perceived more clearly. Light reflects off the floor and emphasizes the lower part of the ribbing. Floor protection is chosen based on the actual contact surface.

If the floor has an active wood or stone pattern, a solid-color enamel calms the composition. If the floor is calm, the fluted base can be highlighted with color.

Light and horizontal fluting

Horizontal grooves react to light differently than a smooth sphere. A side light source creates a sequence of bright edges and dark recesses. The more contrasting the finish and the closer the light, the more active the texture.

STL-035, due to its height, shows more horizontal lines vertically. STL-036 stretches the fluting across a wide hemisphere, emphasizing its groundedness.

Frontal light reduces shadows and makes the shape calmer. Top lighting enhances the lower edges. Before painting, it is useful to test the color in the same light direction.

Glossy enamel reflects light more strongly and emphasizes every unevenness. Matte makes the object softer. The degree of gloss is chosen after a test sample.

How to paint STL-035 and STL-036

Both models come with one layer of primer-sealer for MDF. This is a protective preparation, not necessarily a finished decorative finish. Before painting, check the surface condition and material compatibility.

Fluting requires even coverage of the grooves. Excess material smooths out the texture, while insufficient leaves unpainted areas. It is better to test on an inconspicuous area or a test sample.

Light enamel emphasizes the architecture and shadows. Dark enamel enhances mass. Bright color turns the base into a standalone art object but requires a calm tabletop and surroundings.

The tabletop and base can be painted in one color or separated by contrast. A uniform finish makes the object monolithic, while contrast highlights the shape more.

Light, dark, or colored enamel

White and milky enamel make STL-035 almost sculptural, and STL-036 resemble an architectural dome. On a light coating, the grooves appear through shadows rather than color.

Gray, graphite, and black enamel enhance mass. For STL-036, this effect is especially noticeable: the wide form becomes a heavy visual anchor. STL-035 retains more vertical dynamics.

A rich color suits an interior where the table should be the main accent. Red, blue, green, or another shade should be checked on the full volume because a large surface appears brighter than a small sample.

If the tabletop has an active stone or wood texture, a neutral base helps avoid competition. If the top is simple, the color of the underframe can take on a decorative role.

How to prepare the tabletop for installation

The tabletop must be level, without hidden defects in the attachment area, and with a pre-approved center. For a round shape, the center is determined simply; for oval and rectangular shapes, both axes need to be checked.

Before drilling, a template of the underframe's top platform is made. Holes, inserts, and fasteners are marked according to the drawing, not the outer contour of the body.

If the countertop is painted or tinted, installation work is done carefully to avoid damaging the finish. Sometimes it is safer to prepare the holes before final finishing.

For glass, the installation scheme is developed by a glass product specialist. Glue, suction cups, or metal elements are chosen based on the specific thickness and treatment.

How to attach the tabletop to the central base

The fastening must hold the countertop against shifting, rotation, and lifting during normal use. It must also transfer the load to the underframe without damaging the MDF.

There is no universal mounting plate for all tabletops. Wood, MDF, glass, and metal require different solutions. The size and location of the fasteners are coordinated with the drawing.

During installation, it is important not to insert an unsuitable fastener into a cavity. The base structure has internal relief, so the attachment points must correspond to the designated area.

After assembly, check that the tabletop is centered and does not rotate. Any deviation increases uneven overhang and changes stability.

How to prepare the base and floor

The floor must be level and strong. On a soft carpet or tile unevenness, even a heavy base may wobble. Before assembly, check the area with a level.

The lower contact area must not have dirt, protrusions, or damage. Protective elements are selected so that they do not reduce stability or create point loads.

If the table will be moved frequently, plan a safe method in advance. STL-035 weighs 24 kg, STL-036 weighs 36.5 kg without the tabletop. With the assembled top, the weight becomes greater.

Do not glue the base to the floor just to compensate for incorrect geometry. The cause of wobbling should be eliminated in the structure or surface.

Delivery and entry into the premises

The dimensions of the underframe are checked not only in the room but also along the delivery route. STL-036 has a size of 800 mm along one axis, so it is important to measure the door, corridor turn, elevator, and stair landing.

STL-035 is more compact, but its spherical shape and rigid packaging also require space. The cards indicate delivery in a rigid box, which increases the shipping dimensions.

It is better to bring the underframe and tabletop separately and assemble them indoors. The finished table may not fit through the door and is harder to lift safely.

Before unpacking, prepare a clean, soft surface. The corrugation and primer must not be scratched with tools or placed on a dirty floor.

How to care for the knurled base

Dust collects in horizontal grooves, so a smooth cloth is sometimes not enough. Use a soft brush or attachment that does not scratch the enamel.

Wet cleaning should be done with a well-wrung cloth. Water should not accumulate in the relief or near the floor. Choose cleaning agents according to the finish coating.

When moving the table, do not pull it by the tabletop if the fastening is not designed for such force. Lift the furniture in a manner consistent with its weight and construction.

It is better to repair enamel damage immediately before the defect expands. Save the color swatch or code after manufacturing.

How to check quality after assembly

Inspect the table under daylight and side artificial light. The corrugation should be evenly painted, without drips, unpainted areas, or clogged grooves.

Check the centering of the tabletop. Measure the overhang at several points. For square and rectangular shapes, diagonals are controlled separately.

Press the edges moderately in different directions. The table should not wobble, turn, or shift. Any instability requires checking the fastening and the floor.

Ensure that protective elements are not visible and do not create misalignment. After a test run, re-check the tightening of the mounting assembly.

What not to do from scratch if you have ready-made STAVROS underframes

You don't need to independently form a ball from many segments, mill hundreds of horizontal grooves, or calculate internal lightening. Ready-made STL-035 and STL-036 already have a given geometry.

The buyer can focus on the tabletop, color, mounting, and placement. This reduces the number of unpredictable operations and helps achieve a smooth fluting rhythm.

A ready-made underframe does not eliminate design, but replaces complex body manufacturing. The commercial route looks like this:

Do not perceive the primer layer as a finished enamel. The base is prepared with a protective insulating primer, and the decorative finish is selected separately.

Do not confuse the weight of the base with the permissible load. 24 and 36.5 kg are the mass of the products, not an indication of how many kilograms the tabletop can weigh.

How to compare models in a real room

Make two floor templates: one to the dimensions of STL-035, the other to STL-036. Place them in front of the sofa and walk around them. This immediately shows how much wider the hemisphere is.

Place boxes or a temporary structure 425 and 300 mm high. Put the tabletop template on top. Evaluate the convenience while sitting and standing.

Look at the layout from the room entrance, from the sofa, and from the adjacent area. STL-036 may look proportional from a distance, but too large up close.

Take photos of both options. The camera helps see whether the table competes with the rug, TV stand, and armchairs.

Practical choice for different tasks

What to buy with a table base

The main accompanying product is the tabletop. But the set does not end with two large parts. A confirmed mounting assembly, suitable hardware, finishing enamel, protective materials for the floor, and, if necessary, professional assembly are needed. Specific fittings are chosen after the drawing.

Mistakes when purchasing STL-035 and STL-036

Choose based on a single render without scale

STL-036 has a dimension of 800 mm and may turn out to be significantly larger than expected. Lay out the template on the floor.

Do not calculate the final height

STL-035 already reaches 425 mm, so a thick countertop changes ergonomics and may raise the surface above the sofa.

Assign the countertop based on the cabinet width

The top platform, mass, fastening, and center of gravity are more important than a simple maximum dimension number.

Assuming the hemisphere is automatically stable

A wide shape helps, but excessive overhang and a heavy tabletop can alter the structure's behavior.

Use ordinary self-tapping screws for glass

A glass tabletop requires a special assembly coordinated with a specialist.

Paint the corrugation with too thick a layer

The grooves lose clarity, and streaks become noticeable under side lighting.

Move the table by the edge of the tabletop

The force is transmitted to the mount. The method of movement is determined considering the total weight.

Do not account for walkways

The wide STL-036 may obstruct movement between the sofa, armchair, and TV cabinet.

Place two bases without calculation

Floor differences and incorrect distance may cause wobbling or bending of the upper part.

Do not check the drawing before ordering.

The photo does not show the mounting platform and the purpose of each dimension.

Who STL-035 is for

STL-035 is suitable for a buyer who wants a compact designer table with a noticeable spherical base. It fits well in a small living room, next to an armchair, in a study, bedroom, lounge area, or as part of a series of accent tables.

The model is especially useful when a height close to a finished coffee table is needed before adding the tabletop. This is both an advantage and a limitation.

STL-035 may not be suitable for a very low composition, a large heavy tabletop without calculation, or a room where the ball is completely hidden by a massive top.

Who STL-036 is for

STL-036 is suitable for a spacious living room, a long sofa, a large round tabletop, a hall, a showroom, and a commercial lounge area. It creates a low architectural center.

The hemisphere is especially effective under directional light, which emphasizes the horizontal grooves. The wide base works well next to large objects.

STL-036 may not fit a small room, narrow passage, and high coffee table. The 800 mm dimension needs to be checked on the plan.

How to buy STL-035 or STL-036 at STAVROS

Start by measuring the area. Mark the sofa, armchairs, rug, passages, and the intended tabletop outline. Then decide whether a height of 425 or 300 mm to the top is needed.

Open the STL-035 and STL-036 cards, download the drawings, and compare the dimensions. For a wide selection, you can buy a coffee table base through the frames and bases category.

After choosing the base, go to the tabletops category. Coordinate the shape, weight, thickness, overhang, and installation. If the top is made by another company, provide them with the base drawing.

Choose the finish enamel and the transport scheme for the finished item. Both bases have significant weight, and the assembled table may not fit through the doorway.

For a complex tabletop, non-standard use, or commercial load, discuss the project in advance with a STAVROS manager and a furniture designer.

Additional materials on coffee table proportions

General questions about height, shape, and choosing a low base are covered in the article "How to choose a coffee table base". If you are comparing a central base with individual supports, the material is useful about proportions and leg height for a coffee table.

These publications remain information hubs. The specific choice between STL-035 and STL-036 is based on their actual dimensions, weight, shape, and role in the interior.

FAQ: Questions about STL-035 and STL-036

How is STL-035 different from STL-036?

STL-035 is taller and more compact: 550 × 425 × 400 × 286 mm, 24 kg. STL-036 is lower, wider, and heavier: 800 × 300 × 452 mm, 36.5 kg. The first model creates a spherical vertical accent, the second creates a wide hemispherical base.

Which base is best for a small living room?

More often STL-035, because it takes up less floor space and leaves more air around. But the height of 425 mm together with the tabletop can be significant, so the final vertical should be checked with a mockup.

Which base to choose for a large sofa area?

More often STL-036. The wide hemisphere better matches the large scale, long sofa, and spacious rug. Passages and tabletop dimensions are still calculated separately.

Which underframe is more stable?

STL-036 is wider and heavier, so visually and geometrically it has a wider base. The actual stability of the finished table also depends on the tabletop, overhang, attachment, floor, and type of load.

Will a round tabletop fit?

The round shape naturally complements both models. The diameter, weight, and fastening are coordinated according to the drawing. The round shape cannot be assigned solely based on the maximum body width.

Can a square tabletop be used?

It can be considered, but the corners create an increased diagonal overhang. Verification of lateral stability and protection against rotation of the tabletop relative to the central base is required.

Can a glass tabletop be installed?

The cards allow glass, but the fastening must be special. Thickness, tempering, edge treatment, size, and weight are determined by a glass specialist.

Can a wooden tabletop be used?

Yes, cards allow a tree. You need to consider the thickness, weight, moisture movements of the array, and the appropriate mounting assembly. For a large tabletop, a separate calculation is required.

How to calculate the final height?

The thickness of the tabletop and the actual height of the mounting assembly are added to the height of the underframe. STL-035 — 425 mm, STL-036 — 300 mm. Then the result is compared with the sofa and the usage scenario.

How to calculate the allowable overhang?

Based on the drawing of the top platform, tabletop weight, shape, mounting, and center of gravity. There is no universal value for all materials. Square and rectangle are checked by diagonals and long sides.

Is a mounting plate needed?

The mounting assembly is selected based on the material and shape of the tabletop. You should not buy a random plate without consultation, because the internal relief of the base limits the permissible attachment points.

Can I use two STL-035 under one tabletop?

This option is only possible after calculating the long tabletop, distance between bases, deflection, and height. The two bases must be on the same plane and mounted symmetrically.

What material are the models made of?

Both models are made from glued MDF blank with deep milling and have a cavity inside. These are not solid oak or beech underframes.

Is there a ready-made coating?

The products have a layer of primer-insulator for MDF. Decorative enamel is selected and applied separately. The primer should not be perceived as the final color and protective finish.

Why are the underframes fluted?

Horizontal fluting creates expressive texture and chiaroscuro. It emphasizes the rounded shape but requires careful painting and regular dust removal from the grooves.

How to move the finished table?

Given the significant weight of the base and mounting. Do not pull the item by the edge of the tabletop. The safe method of moving is determined during assembly and, if necessary, performed by two people.

What should be checked before ordering?

Article number, drawing, dimensions, weight, final height, tabletop, overhang, fastening, passages, finish, and method of delivery to the room. For a non-standard project, parameters are agreed with the manager and designer.

Project control card before transfer to the workshop

For a central-type underframe, a unified project card is especially useful. In it, the designer, client, tabletop manufacturer, and assembler see the same dimensions. Without such a document, one participant might consider 550 mm as the diameter of the upper platform, another as the maximum body dimension, and a third as the permissible tabletop size. The card specifies the product parameters, but the purpose of each mounting zone must be read from the drawing.

Write down the full article number and confirmed dimensions

For STL-035, specify 550 × 425 × 400 × 286 mm and weight 24 kg. For STL-036 — 800 × 300 × 452 mm and 36.5 kg. Do not shorten the specification to the words "ball" and "hemisphere": the craftsman must open the correct drawing and check the mounting platform.

Draw a vertical section

The section shows the floor, underframe, upper platform, mounting unit, and tabletop. Set the height of the finished item and mark the position relative to the sofa. This makes it clear whether 425 or 300 mm is suitable and how much the upper part adds.

Draw a top view plan

The plan marks the contour of the base and tabletop. For a round top, a uniform overhang is visible; for a square, the maximum projection of corners; for a rectangle, different shoulders along two axes. The plan also shows passages around the furniture and the distance to the carpet, armchairs, and cabinet.

Agree on the tabletop material

Record wood, MDF, glass, metal, or other material, thickness, and weight. The words "light" or "ordinary" are not suitable for structural approval. The manufacturer must provide exact parameters and the fastening scheme.

Describe the mounting unit

Specify fasteners, holes, embedded parts, and assembly order. For glass, the unit is fundamentally different from a wooden tabletop. Any improvisation after painting increases the risk of damage to the knurling and primer.

Approve the finish

Save the color code, gloss level, and test swatch. The ribbing changes the perception of the shade: the protrusions are lighter, the grooves are darker. A swatch on a flat part does not fully show the result, so it is useful to apply the sample to a profiled surface.

Check the delivery route

STL-036 has dimensions of 800 mm and a weight of 36.5 kg, STL-035 — 24 kg. Considering the packaging and the tabletop, you need to check doorways, stairs, elevator, and the possibility of assembly in the room. It is often safer to bring the parts separately.

Perform a dry assembly

Before final fixation, center the tabletop, check the axes, overhang, and stability. Then remove the parts, perform finishing work, and assemble the table according to the approved scheme. This procedure reduces the risk of reworking an already painted product.

The control card links the beautiful shape to the actual construction and helps to get a table that looks proportional, sits comfortably by the sofa, and is safe for daily use.

Result: STL-035 or STL-036

Choose STL-035 if you need a taller, more compact, and sculptural coffee table. The spherical base measuring 550 × 425 × 400 × 286 mm and weighing 24 kg works well in a small living room, next to an armchair, and in an author's composition where air should remain around the support.

Choose STL-036 if you need a low, wide, and architectural center for the sofa area. The hemispherical base measuring 800 × 300 × 452 mm and weighing 36.5 kg matches the large tabletop in scale and is more connected to the floor, but requires enough free space.

Both models are made of deep-routed MDF, have an internal cavity, "Prestige" sanding, primer-insulator, and the possibility of subsequent painting. Neither the sphere nor the hemisphere automatically determines the tabletop. Before purchasing, you need to check the drawing, final height, weight, overhang, and fastening.

On STAVROS, you can go from a specific base card to the tabletop category and assemble the project as a single system. This route is more reliable than a random combination: STL-035 or STL-036 is chosen based on the actual room, furniture, and structure, not just the striking shape.

Step-by-step selection route without random decisions

First, determine the role of the table

Write down whether it will be a central coffee table in front of the sofa, a side table next to an armchair, a decorative art object, an occasional piece, or furniture for a commercial lounge area. The same shape is perceived differently depending on the function. STL-035 is more often suitable for a compact accent scenario, STL-036 for a large low center of the soft seating group.

Measure not only the free space but also the path of movement

On the plan, mark the passages from the sofa to the door, the distance to the TV cabinet, armchairs, carpet, and other items. The STL-036 template up to 800 mm wide can show that the base takes up significantly more floor space than it seemed in the photo. For STL-035, the main limitation is often the final height rather than the width.

Compare the height with the furniture

Measure the seat and armrest. Then add the thickness of the selected tabletop and mounting assembly to 425 or 300 mm. Place a temporary surface on boxes of the appropriate height and try using it while sitting. Such a simple mockup reveals discomfort before purchase.

Choose the tabletop shape

A round top supports a round base and provides an even overhang. A square one enhances contrast but creates long diagonal levers. An oval one suits an elongated soft seating group, while a rectangular one may require two bases. The shape is chosen not only by style but also by stability.

Determine the material and weight of the top

Request the exact weight of the tabletop from the manufacturer. Thick solid wood, glass, and metal can differ significantly in load. Do not use approximate estimates. If the tabletop has not been selected yet, first open the category, select several options, and provide their specifications to a specialist.

Check the top mounting area

The external shape of the body is not equal to the attachment zone. Download the drawing of STL-035 or STL-036 and clarify where fasteners can be placed considering the internal cavity. This is especially important for a large tabletop that requires multiple fixation points.

Coordinate the overhang and lateral load

On the template, mark the outline of the base and the tabletop. Check how far the edge protrudes at each point. Imagine a typical situation: a person places a hand on the corner, a child leans on the table, or a guest places a heavy object near the edge. The design must account for real actions, not just uniform static load.

Approve the color before final assembly

Make a test paint and evaluate it on the horizontal ribbing. Light enamel makes the grooves graphic, dark enamel enhances mass, bright enamel turns the base into a dominant element. The color of the tabletop and underframe should be considered together because contrast changes the visual size of both parts.

Plan delivery and installation

Check the packaging, doorways, and assembly area. The STL-036 is heavier and wider, so it is safer to carry it separately from the tabletop. Tools, pads, and mounting hardware are prepared in advance to avoid placing the primed base on a dirty floor or searching for parts during assembly.

Only after checking, complete the set

The cart should contain not just a base and a random tabletop, but a coordinated set: the selected article, a compatible top, an installation diagram, finishing materials, and floor protection. This approach preserves the commercial logic of the purchase and reduces the risk that a striking shape will remain without a compatible tabletop or prove inconvenient in the room.

Final check before paying for the order

Before payment, it is useful to conduct a short but thorough check. It does not replace a designer consultation, but helps ensure that the purchase is logically assembled and no important parameter is left "for later."

Item number and drawing

Make sure the order specifies STL-035 or STL-036, and the craftsman works with the corresponding drawing. The similarity of rounded shapes does not make the parts interchangeable. Height, width, weight, and mounting area differ.

Final height

Add the base height, tabletop thickness, and the actual mounting allowance. Compare the result with the sofa, armchair, and the table's purpose. Do not use only an interior photo as a guide: the scale of upholstered furniture varies per project.

Tabletop and overhang

Check the shape, weight, material, and maximum edge overhang. For a square tabletop, check the diagonals separately; for a rectangular one, the long sides; for glass, a special mounting assembly.

Number of bases

For a compact tabletop, one central base is usually considered. For a long top, a pair may be required, but this decision is made by the designer. Do not add a second base just for aesthetics without calculating deflection and flatness.

Finishing

Clarify that the primer-insulator layer is not the selected enamel. Record the color, gloss, and application technology. The knurling must remain sharp after finishing.

Delivery and assembly

Check the packaging dimensions, delivery route, and installation location. Prepare a clean surface and enough people for safe movement. After assembly, check centering, wobble, and fasteners.

If all six points are covered, the choice between STL-035 and STL-036 transforms from a visual preference into a ready furniture project. The buyer understands in advance exactly what they are getting, how it connects to the tabletop, and how the piece will function in the room.

Commercial conclusion for choosing a specific article

STL-035 and STL-036 do not compete as a "good" and "bad" base. They cover different scenarios. The first is chosen for height, compactness, and spherical form; the second for low profile, wide support, and strong architectural mass. Therefore, the right question is not "which model is better overall," but "which model matches my tabletop, sofa, walkways, and usage."

For a hesitant buyer, the rational route is simple: open both cards, download drawings, make floor and vertical templates, select several tabletops, agree on fasteners, and only then place the order. This sequence helps buy a coffee table underframe without random assumptions and get a piece that remains expressive after actual assembly, not just in visualization.

If after the mockup both shapes look appropriate, the final choice can be made based on the base's role. STL-035 is perceived more as a separate sculpture under the tabletop and better preserves free space around it. STL-036 forms a low monolithic center and visually unites a large soft seating group. In both cases, technical compatibility is more important than decorative impression: the dimensions of the top platform, tabletop weight, overhang, and mounting must be confirmed before payment, painting, and delivery.