Don't want to assemble complex facade decor: when one carved polyurethane overlay NPU-382 above the entrance is enough

Above the front door, there is a free field on the facade. It is noticeable enough to make the entrance seem unfinished, but building a full portal around the door with pilasters, several moldings, brackets, and a complex stucco composition is not desirable at all. In such a situation, a different approach is appropriate: not to fill the entire plane, but to find one strong central element and let it work on its own.

NPU-382 is a carved decorative overlay for a polyurethane molding. In the STAVROS catalog, it is linked to the molding MLDPU-002 and is available in two sizes: 297 × 404 × 18 mm for 8,930 RUB and 338 × 406 × 18 mm for 9,420 RUB. This is no longer a miniature furniture detail that is only noticed up close. The size of about 300–340 × 400 mm allows NPU-382 to be considered as an independent ornamental center above the front door—but only where the scale of the facade itself matches.

The main question before purchasing is not "is NPU-382 beautiful?". It is much more useful to ask: can a single overlay hold my specific free field above the entrance?

Sometimes the answer is yes. Then a complex system is really not needed: one carved element, correctly positioned relative to the door and the trim, is enough.

Sometimes NPU-382 itself is suitable, but too much unorganized surface remains around it. Then a second scenario appears—complement the overlay with a compatible molding MLDPU-002 measuring 22 × 11 × 2600 mm and turn the central ornament into part of the frame composition.

And there is a third situation: the entrance is so large, tall, or architecturally complex that one overlay and a thin molding are objectively not enough. Then it is more honest to immediately move to developed facade decor, rather than trying to make NPU-382 imitate a full pediment or portal.

It is precisely between these three solutions — NPU-382 alone → NPU-382 + MLDPU-002 → a more developed facade composition — that you need to choose.

Polyurethane Moldings NPU-382

from 107.59 $

Go to Catalog

One strong element sometimes works better than five weak ones

Facade decor is easy to overload.

A person sees a beautiful catalog and starts adding details: molding around the perimeter, another profile on top, a bracket on each side, a medallion in the middle, pilasters by the door, an additional rosette under the cornice. Each item on its own can be expressive. Together they start to argue.

This is especially noticeable on a relatively small private house.

The entrance group turns out to be several times richer than the rest of the facade. A strange impression arises, as if a piece of another building was attached to a calm house.

Therefore, the desire to limit oneself to one carved overlay is not at all a sign of simplifying the project. Sometimes it is a more precise architectural solution.

NPU-382 is interesting precisely because it can occupy the center of a free plane without requiring mandatory surrounding with many other details.

The relief creates a shadow.

A width of about 300–340 mm makes the pattern noticeable.

A height of about 400 mm creates a sufficiently large vertical accent.

At the same time, the facade plane remains around it, and it is this that helps the decor read clearly.

There is an important design principle: relief needs a background. If every 10 centimeters of the wall is occupied by a new profile, none of them is perceived separately.

Therefore, a single element can look more convincing than a complex system—provided its size matches the architectural field.

Watch video ...

NPU-382 is not bought as a ready-made pediment.

It is important to understand the product itself correctly here.

NPU-382 is not a ready-made door frame.

Not a pediment in the full architectural sense.

Unfinished portal.

Not a pediment.

Not a set of multiple parts.

This is a carved decorative overlay for polyurethane molding.

Connection with MLDPU-002 allows using it within a more developed composition, but does not obligate doing so in every project.

That is why two equally valid scenarios are possible.

In the first, the overlay exists independently — as a central relief above the door.

In the second, it becomes the decorative center of the molding frame.

It is wrong to reason like this:

since NPU-382 is called a molding overlay, without molding it is meaningless.

Connection with a specific profile shows compatibility and the ability to build a system. But a real facade may allow using one ornament without an additional frame if compositionally it already completes the free field.

Before ordering, it is useful to first look at the card itself and buy the carved overlay NPU-382 only after fitting the required size to your entrance.

Our factory also produces:

Wooden Decor N-328

from 129.04 $

Wooden Decor N-329

from 119.76 $

Wooden Decor N-330

from 479.05 $

Wooden decor N-334

from 102.29 $

Wooden Decor N-356L

from 118.20 $

Wooden Decor N-356R

from 118.20 $

Wooden Decor N-422

from 186.51 $

Wooden Decor N-354R

from 995.57 $

View Full Product Catalog

Two sizes of NPU-382 are not just two prices

The card presents two options.

Height difference is almost nonexistent — 404 and 406 mm.

But width changes more noticeably: 297 vs 338 mm.

This means it's more logical to choose between options primarily by the width of the free space.

On a relatively narrow area above the door, the 338 mm version may come too close to the side borders of the decorative zone.

On a wide facade, conversely, 297 mm may look too modest.

The price difference is:

9 420 − 8 930 = 490 ₽.

Therefore, savings here should hardly be the main criterion. It is much more costly to make a mistake with the scale and get a visually weak result on the finished facade.

The most useful thing before ordering costs zero rubles — a paper template

The facade deceives the eye.

On a monitor, 297 × 404 mm looks quite large.

But when you transfer this size to the wall of a two-story house, the detail unexpectedly shrinks.

There is a simple test worth doing before placing an order.

Cut out two rectangles from paper, cardboard, or film:

• 297 × 404 mm;
• 338 × 406 mm.

There is no need to accurately reproduce the complex pattern. For assessing the first scale, the overall size is sufficient.

Attach the first template to the intended location.

Step back.

And not by a meter.

First, stand roughly where you usually approach the house: at the gate, path, parking area, or driveway.

Then come closer.

Switch the template to the second one.

Take a photo.

This way, in a few minutes, you can see what a size chart won't show: whether the NPU-382 holds the facade field or blends into it.

The door size is only half of the initial data.

One typical mistake is measuring only the door opening.

For example:

"A door 1000 mm wide. So, a 338 mm overlay will take about a third of the width and should fit."

The calculation is convenient, but incomplete.

The decor is perceived not relative to the door leaf, but relative to the entire visible composition.

You need to measure:

1. the width of the doorway;
2. the outer width of the trim or other framing;
3. the width of the free wall above them;
4. the distance to the cornice, canopy, or other upper limit;
5. the distance to adjacent windows, corners, and vertical elements;
6. the full width of the entrance group.

If the door is 1000 mm, and together with the trim the entrance takes up 1450 mm, NPU-382 is already perceived relative to 1450 mm, not relative to a thousand.

If there is a pediment four meters wide above this composition, the scale changes again.

You need to measure the "decor field," not just the wall

It is useful to introduce a simple concept — the working field above the entrance.

This is the area within which the NPU-382 must exist as a complete central accent.

Its boundaries can be:

• the outer edges of the door frame;
• vertical pilasters;
• the corners of the facade;
• side windows;
• cornice;
• the canopy;
• the horizontal band.

Suppose the actual free width of the field above the door is 1200 mm.

Then the NPU-382, 297 mm wide, takes up about a quarter of that space.

338 mm is a bit more.

On a 2000 mm field, the same part becomes significantly smaller relative to the background.

This does not mean there is a universal "correct proportion" in percentages. We are not inventing such a norm.

But comparing the size of the overlay with the actual field perfectly shows why one NPU-382 looks convincing on one house and seems lost on another.

When the NPU-382 can really work alone

There are several signs of a successful scenario.

The free field is not excessively large

The overlay must remain readable from a normal distance.

If it turns into a tiny dot on a huge pediment, a single element is not enough.

The entrance already has a pronounced frame

For example, the door is framed with architraves.

Then NPU-382 does not have to rebuild the entire geometry. The lower part of the composition is already formed.

The overlay completes it from above.

The rest of the facade is quite calm.

A single relief center on a clean wall reads better.

The architecture does not require pilasters and a complex portal.

Not every house needs a grand palace entrance.

The NPU-382 ornament aligns with the character of the house.

Such a carved element is perceived especially naturally where classical, neoclassical, or other ornamental motifs are already present.

When these conditions coincide. molding overlay NPU-382 buy it can be used precisely as an independent central element, without turning the purchase into the start of an endless set of facade decor.

When one NPU-382 looks too lonely

The opposite scenario also has clear signs.

The first is a huge empty field.

Suppose there is a triangular pediment several meters wide above the door. An overlay about 400 mm high remains noticeable, but no longer structures the space.

The second is an overly large entrance group.

A tall double door, massive side elements, a wide canopy. In such architecture, a small central ornament may look like a randomly added accessory.

The third is that the facade is already built on strong lines.

For example, there are wide moldings around the windows, corners are highlighted, and there is a large cornice under the roof. One NPU-382 without connection to these lines will be stylistically isolated.

The fourth is the absence of a visual frame for the entrance itself.

If the door is simply inserted into a huge smooth wall, one medallion at the top is not always enough to fix the feeling of incompleteness.

This is where MLDPU-002 comes in.

MLDPU-002 changes not the ornament, but the architecture around it.

MLDPU-002 is a polyurethane molding measuring 22 × 11 × 2600 mm.

The current price of one strip is 5,460 ₽.

Compared to NPU-382, it looks much simpler. A linear profile, without the task of becoming the main decorative object.

But it is exactly this simplicity that is needed.

NPU-382 is responsible for the center.

MLDPU-002 is for the line.

Together they can build a complete system:

• molding limits the field;
• sets a horizontal line or frame;
• connects the decor with the door;
• NPU-382 removes the monotony of the line and creates a central culmination.

If after trying one overlay you get the feeling that a beautiful detail hangs by itself, it is likely that a structuring line is missing.

Then it is reasonable buy molding MLDPU-002 to first model a simple frame composition rather than adding two or three random overlays.

Three levels of entrance decoration — a table for decision-making

This table is much more useful than the question "which is prettier?"

All three solutions can be beautiful.

Only the one that matches the scale of a particular house will be correct.

Don't confuse a single accent with an unfinished composition.

Minimalism in decor is not when there are few elements.

It's when there are exactly as many elements as needed.

One NPU-382 looks complete if it is perceived as a deliberate center.

It looks unfinished when the viewer intuitively expects the line to continue.

For example, there are vertical trim pieces on the sides of the door, but they are not connected at the top. The NPU-382 is installed higher between them.

The eye may expect a horizontal completion.

Then MLDPU-002 is able to tie the composition together.

Now another facade: around the door there is already a finished rectangular frame. Above it remains a calm field.

Here an additional molding may become redundant, and one NPU-382 is exactly the accent that was missing.

The central axis of the door is the first place to place the template

The most natural start is centering NPU-382 relative to the doorway.

Let us denote:

• the width of the architectural entrance as W;
• the width of the selected NPU-382 as A.

With symmetrical installation:

X = (W − A) / 2.

For example, the external width of the door frame is 1400 mm.

For an overlay of 338 mm:

(1400 − 338) / 2 = 531 mm.

So, relative to the boundaries of this composition, 531 mm remains on each side.

Such arithmetic is not needed for the beauty of the formula.

It helps to check whether the overlay is truly centered on the door axis, especially when the facade is plastered and it is difficult to judge by eye.

However, there are exceptions.

If the entrance door is offset relative to the architectural risalit or the entire entrance group is asymmetrical, mechanical centering only on the door leaf may be incorrect.

Then you need to find the main axis of the entire facade composition.

Height above the door: too close — cramped, too high — the connection falls apart

The NPU-382 has a height of about 400 mm.

Therefore, it needs not only space in width, but also a sufficient vertical zone.

If the bottom edge almost touches the trim, the relief visually sticks to the door frame.

If the overlay is raised too high, a gap appears between the door and the decor, and the two elements are no longer perceived as one entrance.

There is no universal correct distance in millimeters here.

It depends on:

• door height;
• trim width;
• facade field height;
• canopy location;
• cornice shape;
• presence of a horizontal molding.

The correct way is again very simple: the template.

Moreover, it is useful to take three photos:

• overlay below;
• centered in the free field;
• above.

Comparing the shots usually immediately reveals the most convincing option.

Small size 297 × 404 mm: where it wins

The 297 mm wide version is suitable not because it is cheaper.

Its advantage is a more compact scale.

It is especially interesting when:

• The entrance is relatively narrow;
• The architraves are already quite active;
• The free plane is small;
• There are windows nearby;
• There is little space between the door and the upper cornice;
• The facade has a restrained neoclassical composition.

A width of 297 mm allows leaving more calm background.

At the same time, a height of 404 mm preserves an expressive vertical proportion.

Such an overlay can look thinner and lighter than the 338 mm option, especially on a small facade.

Size 338 × 406 mm: when an additional 41 mm of width is needed

The difference between 297 and 338 mm is 41 mm.

On paper, this is a little.

In the ornamental detail, the expansion is noticeable.

The larger version holds better:

• a wide door;
• a massive frame;
• a large free field;
• a facade where other elements also have a large scale.

But here there is an interesting nuance.

The height practically does not increase.

Consequently, the second size does not simply become "larger in all directions." It becomes primarily wider.

This is useful when the decorative center lacks horizontal weight, but vertical space is limited.

How to choose between two sizes without a design visualization

No complex project is needed.

Make four actions.

First: take a photo of the facade strictly from the front.

Second: measure one known dimension — for example, the external width of the door.

Third: scale the photo in any graphic editor.

Fourth: overlay two rectangles with proportions of 297 × 404 and 338 × 406.

Do not try to depict the ornament itself yet.

Look only at the area.

If 338 mm is already too tight in terms of dimensions, the answer has been found.

If 297 mm turns into a barely noticeable dot, that too.

If both versions look appropriate, then the choice can be made based on the character of the pattern and the desired expressiveness.

Why NPU-382 should not be stretched across the entire pediment

The word "pediment" often creates incorrect expectations.

There is a triangular plane — meaning it needs to be filled with decor entirely.

No.

Empty space is also an architectural material.

NPU-382 can be placed in the center of a large pediment, leaving a lot of wall around it. But in this case, the viewing distance needs to be checked.

If the ornament still reads as a significant center, the emptiness works in its favor.

If the element almost disappears, the problem is not the amount of empty wall, but an insufficient scale.

Then it's better to understand, how to choose decor for the gable of a house, and decide whether a molding outline, a larger center, or a developed architectural system is needed.

It's wrong to simply buy four more NPU-382 and spread them across the corners of a huge plane.

The entrance group is already framed with trim: the strongest scenario for a single overlay

Let's imagine a house with a finished entrance.

There is a door.

Around it is trim.

Below are steps.

Nothing above.

The architecture already has a frame, but the finish seems too dry.

This is where one NPU-382 is particularly convincing.

It should not build the entrance from scratch.

It has only one job left: to create the top center.

In this case, the scheme becomes simple:

trim → door → NPU-382.

Neither pilasters nor additional brackets may be needed.

If such a laconic architecture suits the house, complicating it for the sake of "richness" is pointless.

If there are no platbands, one NPU-382 may not be enough

Now the opposite situation.

Smooth wall.

Simple door.

No framing.

A beautiful carved overlay is installed above it.

What does a person see?

The door itself.

The ornament itself.

There is no architectural connection between them.

This is exactly where you should check the NPU-382 to MLDPU-002 pairing.

Even a small linear contour can connect elements.

Can be viewed Decor for molding MLDPU-002 and evaluate compatible parts before the project starts to grow with random items.

What compatibility of NPU-382 with MLDPU-002 means for the buyer

This is not just a technical note in the catalog.

For the buyer, such a connection removes one of the most difficult tasks — finding a profile that can be visually linked to the overlay.

A common mistake in self-designing a facade looks like this:

1. a person buys a beautiful central piece;
2. then starts looking for molding;
3. chooses the first one they like;
4. the profile turns out to be too massive or stylistically alien;
5. the composition falls apart.

When NPU-382 is already provided as decor for MLDPU-002, the search becomes more specific.

You can immediately buying polyurethane molding decor within one logic, rather than assembling a facade from random details of different scales.

How many MLDPU-002 will be needed — you need to calculate based on the actual scheme

One plank has a length of 2600 mm.

But you cannot write a universal number of planks for a door.

It all depends on what kind of frame you are building.

For example, only a horizontal line 1500 mm long is required.

One plank of 2600 mm covers this size in length.

If a U-shaped composition is needed:

• top — 1500 mm;
• two side sections of 600 mm each.

Total:

1500 + 600 + 600 = 2700 mm.

One plank of 2600 mm is already less than the total required length.

Additional material will be needed, taking into account the actual layout and cutting.

That is why molding cannot be added to the cart on the principle of "one plank, probably enough."

First, a diagram is drawn.

One element or a molding frame: which looks more expensive

The question is formulated incorrectly.

A larger number of details does not look more expensive.

A controlled composition looks more expensive.

One NPU-382 on a well-calculated field can give the impression of a much more cohesive architecture than a frame of five elements whose sizes are not coordinated with each other.

Conversely, on a large entrance, a single overlay sometimes resembles a small decorative badge, while a simple molding line instantly brings the entire space together.

Therefore, the criterion is not "richer."

The criterion is more complete.

Neoclassical facade: NPU-382 without an extra frame

Neoclassicism loves relief, but poorly tolerates an excessive amount of ornament.

The following scheme suits it:

• calm, light, or other uniform facade plane;
• neatly designed door;
• one NPU-382 above the entrance;
• minimum of additional lines.

The overlay creates a classic reference, but the house does not turn into a palace stylization.

It is especially important to keep a free field around the element.

This way the relief is perceived more easily.

Pronounced classicism: one detail may not be enough

If the facade already has:

• rusticated corners;
• large cornice;
• rich window casings;
• pilasters;
• developed horizontal belts,

one NPU-382 risks being too modest for the entrance.

The entrance group should usually support the scale of the rest of the architecture.

Here it is more reasonable to consider NPU-382 as a central part, rather than the entire decor.

MLDPU-002, larger profiles, or additional architectural elements will help integrate it into the system.

For a general understanding of this approach, it is useful to look at facade stucco for the entrance group and compare the scale of a single accent with the full design of the door and surrounding wall.

Modern facade: one classical element is a strong but risky technique

On a modern house, NPU-382 becomes a contrast not only in color, but also in plasticity.

Smooth plaster.

Large rectangular windows.

Simple door.

Straight canopy.

And suddenly — a pronounced carved ornament.

Such a move can be deliberate and interesting.

But it should be repeated at least in the logic of the entrance area.

If this is the only classical motif on the entire building, you need to carefully check whether it looks like an accent or a random borrowing.

In such a project, adding ten more classical elements around NPU-382 just to justify the first overlay is also unnecessary.

Sometimes one strong detail is better.

Sometimes it's better to abandon it altogether.

Match NPU-382 with the width of the door casings.

There is another scale that is often forgotten.

The width of the door casing.

Suppose the door frame is very thin — visually light.

Above it is placed a large carved NPU-382, 338 mm wide.

An imbalance may occur: the top becomes significantly heavier than the sides.

And vice versa.

Massive casings with a deep profile and a too compact NPU-382 of 297 mm can make the top piece look weak.

No exact mathematical ratio is required.

Need to match the visual weight.

A tone-on-tone color makes the large NPU-382 calmer.

A size of about 300 × 400 mm is quite noticeable.

But color can radically change its perception.

If NPU-382 is painted in the facade color, the ornament reads through relief and shadow.

This option works well when:

• you want to avoid excessive decorativeness;
• the house is light;
• the facade is built on a single calm palette;
• you need to emphasize form, not color.

The 18 mm relief remains noticeable under side lighting, but does not divide the wall into contrasting patches.

The contrasting overlay above the entrance immediately becomes the main object

The dark NPU-382 on a light facade will be perceived significantly more actively.

This may be justified if the same color is already repeated:

• in the door;
• window frames;
• roofing;
• metal decor;
• other architectural lines.

If there is nothing similar, the single contrasting spot above the entrance risks looking glued on after the facade is completed.

Contrast requires a stricter composition than tone-on-tone coloring.

Can NPU-382 be matched to the color of the door rather than the facade?

This technique can be considered if the door itself is a strong compositional center.

For example:

• dark door;
• light facade;
• calm trim.

NPU-382 of the same visual tone can extend the vertical axis upward.

But the rule of repetition applies again.

If the color of the overlay is not related to anything except the door, you need to evaluate a photo of the entire facade.

Sometimes the connection turns out to be strong.

Sometimes two dark points — the door and a small ornament — look disconnected.

Material matters, but you cannot invent properties for it that are not in the confirmed data.

Confirmed: NPU-382 is made of polyurethane.

This is enough for an accurate product description.

There is no need to add random numbers for frost resistance, density, water absorption, or service life of NPU-382 specifically to the article if they are not confirmed by the specific product card.

For the buyer, the practical conclusion is different.

If the overlay is planned for an exterior facade, before final installation you need to clarify:

• the acceptability of exterior use for the specific product;
• requirements for the substrate;
• surface preparation;
• the painting system;
• recommended mounting composition;
• treatment of the junction.

This approach is much more useful than the advertising phrase “polyurethane is not afraid of anything.”

You cannot automatically transfer interior installation technology to the facade.

Even if a person previously glued polyurethane decor in a room, the exterior wall is a different environment.

Here there are:

• atmospheric precipitation;
• temperature changes;
• sun;
• exterior substrate;
• facade finishing system.

Therefore, before starting work, you need to choose molded decoration adhesive not just out of habit, but taking into account the specific installation location and recommendations for the exterior surface.

If precise installation of NPU-382 on a specific facade is in doubt, it is better to clarify the system in advance with STAVROS or a facade finishing specialist.

Why you cannot choose a location in the center of a brick, panel, or joint

Sometimes builders focus on the facade finishing material:

"Here is the middle of the panel — let's place it here."

But the architectural axis may not coincide with the layout of tiles, bricks, or plaster maps.

For NPU-382, the main reference point should be the entrance composition.

First, the door.

Then the trim.

Then the common axis.

And only after that — the finishing seams.

If, to hit the brickwork, the overlay is shifted 40–50 mm relative to the door, the asymmetry will be more noticeable than the installation convenience.

The canopy above the door radically changes the task

If there is a canopy above the entrance, the free facade field may be partially hidden.

You need to understand where the NPU-382 will be located relative to:

• the top line of the canopy;
• its depth;
• the supports;
• lighting.

An overlay positioned too low behind a deep canopy can almost disappear when viewed from the front.

If placed higher, it becomes visible again, but may lose its connection with the door.

Therefore, when a canopy is present, the template should be evaluated from the outside, from the usual approach point to the house.

Light can make a single NPU-382 more expressive than an entire frame.

The 18 mm relief works not only through its shape.

It creates a shadow.

With side natural lighting, the ornament becomes deeper.

If the entrance is illuminated in the evening, the position of the fixtures can also change perception.

But you shouldn't design the overlay solely for a striking shadow.

First, the composition should work during the day without light.

Lighting is an amplifier, not a crutch.

What to do if you want to place two NPU-382 symmetrically

At one entrance, a single central element is usually more logical.

Two identical overlays are needed only if the architecture truly has two independent symmetrical fields.

For example, a wide entrance block consists of two side sections separated by a central axis.

But you shouldn't buy two NPU-382 just because the facade seems large.

A large space does not always require doubling the decor.

Sometimes it needs a more developed line — for example, MLDPU-002.

NPU-382 above the door and NPU-382 on the pediment are two different scales of perception.

Above the front door, a person is relatively close to the detail.

On a high pediment — far away.

The same NPU-382 visually shrinks with distance.

Therefore, the phrase "a 400 mm overlay is quite large" by itself says nothing.

For a first-floor door, 400 mm can be very expressive.

For a high pediment of a two-story building, they are modest.

This is another argument against choosing based on a catalog photo.

Why you can't assemble a complex composition just because NPU-382 is called a molding decor.

The product category suggests possibilities, not obligations to use them all.

The buyer may have a simple task:

I like the NPU-382. I want to place it above the door and nothing else.

If the template shows that the composition is complete, that is enough.

There is no need to create a frame just because a compatible MLDPU-002 exists.

And the reverse rule also works.

If one overlay looks lost, there is no need to protect the original minimalism at any cost.

Adding a molding becomes a logical development of the project.

NPU-382 + MLDPU-002: the most natural step of complexity

Of all the ways to add decor to the NPU-382, the compatible molding is the most understandable first step.

Not brackets.

Not sockets.

Not pilasters.

First, the line.

Why?

Because the problem with a single trim is almost always the lack of connection to the boundaries of the architectural field.

Molding creates that connection.

This results in a clear hierarchy:

1. door;
2. framing;
3. central NPU-382.

If this is enough, the system is complete.

How can MLDPU-002 be used around the central NPU-382

The specific layout needs to be built for the facade, but there are different compositional directions.

Horizontal line

MLDPU-002 goes above the door, and NPU-382 becomes the center.

This is the most concise way.

Rectangular field

The molding creates a frame, NPU-382 is inside it.

Suitable if the free facade plane is large enough.

Connection with vertical casings

The molding line continues the existing entrance geometry and includes NPU-382 in the upper part.

But you cannot choose a scheme until measurements are taken.

Why the frame should not compress the ornament

NPU-382 already has a complex pattern itself.

If you outline it with MLDPU-002 too tightly, almost no background will remain between the molding and the edge of the ornament.

The details will start to blend together.

The composition will become heavier.

Therefore, when designing the frame, enough free surface should be left so that the central overlay and the linear profile are perceived as two levels.

The specific offset depends on the field and the pattern — a universal number should not be invented here.

When it's time to give up and move to a larger system

There are situations where adding another strip does not save the scale.

For example:

• the entrance spans two floors;
• above the door there is a huge triangular pediment;
• large pilasters already run along the facade;
• the cornices are very massive;
• the width of the entrance group is several meters.

NPU-382 may remain part of the solution, but it ceases to be the main standalone tool.

Here it already makes sense to look order polyurethane facade decor comprehensively.

It is the word "comprehensively" that is important.

Do not buy elements one by one, but first determine the architectural scheme.

How not to confuse NPU-382 with other types of decor

This is not a rosette

A rosette is usually perceived as an independent center of a different geometry.

This is not molding

MLDPU-002 is a linear profile. NPU-382 is a carved accent.

This is not molding.

The overlay has a fixed size and a finished pattern.

This is not a pediment.

It can decorate a pediment, but does not replace its architecture.

This is not a ready-made portal.

A full portal requires other elements and a different scheme.

Understanding these differences protects against wrong expectations after purchase.

What to buy together with NPU-382

Buying everything from the table is not required. It shows routes depending on the project.

This logic preserves the budget and prevents the project from growing uncontrollably.

First, the central NPU-382.

Only then the question: what does it really lack?

The price of the three scenarios starts from completely different amounts

For the single option, everything is simple:

• NPU-382 297 × 404 × 18 mm — 8,930 ₽;
• NPU-382 338 × 406 × 18 mm — 9,420 ₽.

If MLDPU-002 is required, moldings are added to the cost of the overlay based on the actual length of the composition.

One MLDPU-002 strip — 5,460 ₽.

For example, a small NPU-382 plus one MLDPU-002 strip:

8 930 + 5 460 = 14 390 ₽.

Large NPU-382 plus one strip:

9 420 + 5 460 = 14 880 ₽.

But this is only an arithmetic example of the cost of the specified items themselves. It does not mean that one molding strip is enough for any entrance.

The quantity is determined by the layout.

Why you shouldn't buy molding "with extra just in case" without drawing a diagram

A profile 2600 mm long seems large.

But a frame composition quickly adds up in meters.

For example:

top — 1600 mm;

side lines — 700 mm each.

Total:

1600 + 700 + 700 = 3000 mm.

One plank is 2600 mm shorter.

Besides the total length, there are cuts and connections.

Therefore, first a drawing with real dimensions is made.

Only then is the quantity calculated.

Error: selecting NPU-382 only by height

Both sizes have a height of about 400 mm.

One might think that since the height of the free field allows it, everything fits.

But the main variation is in width.

Need to compare both 297 and 338 mm.

Error: evaluating the overlay in hands, not on the facade

On the table, the NPU-382 looks large.

On the house — otherwise.

Only a full-size template gives an honest scale.

Mistake: taking the larger version as automatically more impressive

Bigger doesn't mean right.

On a compact entrance, the extra 41 mm can make the center heavier.

Mistake: placing the NPU-382 relative to the door leaf, ignoring the architraves

The architectural width of the entrance is usually greater than the leaf.

The axis and proportions should be assessed by the whole composition.

Mistake: raising the overlay too high

The ornament will be connected to the pediment, but will no longer be connected to the door.

If the goal is decor above the front door, this connection is critical.

Mistake: placing it too low

Then NPU-382 begins to press on the top of the trim.

Visually readable space should remain between elements.

Mistake: adding MLDPU-002 just because it is compatible

Compatibility is an option, not an obligation.

If one element already completes the field, the molding may become redundant.

Mistake: refusing MLDPU-002 out of a principle of minimalism

Sometimes a frame is objectively necessary.

Minimalism does not justify compositional incompleteness.

Error: trying to replace a huge pediment with NPU-382

It is a decorative center, not an architectural system several meters in size.

Error: mixing several central accents

NPU-382, rosette, lock, and medallion simultaneously create competition.

Choose one main center.

Error: buying facade decor before assessing the entire house

The entrance cannot be designed as a separate apartment within the facade.

Its scale should correspond to the windows, cornices, and overall architecture.

Error: using unverified external mounting technology

A specific base and external conditions require an appropriate solution.

The exact adhesive, preparation, and finish must be determined before installation.

Who the “one NPU-382” scenario is especially suitable for

This approach should first be considered by a homeowner who:

• the front door already has a frame;
• there is an empty field above it;
• the facade is relatively calm;
• there is no desire to build a complex portal;
• one central ornament is needed;
• a full-size template of 297 or 338 mm is clearly readable from the street;
• Adjacent architectural elements do not require a larger scale.

In this situation, one overlay is not a compromise.

This is a complete concept.

It is better to look at NPU-382 with MLDPU-002 right away.

The combination is more useful when:

• the door itself looks too separate;
• it is necessary to form the top frame line;
• the free field is significantly wider than the overlay;
• the facade already uses linear profiles;
• the central element without a frame seems to be "hanging";
• I want to connect NPU-382 with the architraves.

Then you can order NPU-382 made of polyurethane and at the same time calculate the required length of the compatible MLDPU-002.

When it is better to refuse NPU-382 in favor of another composition

This is also a normal selection result.

NPU-382 may not be suitable if:

• both versions are too small;
• the ornament is stylistically alien to the house;
• the field requires a large architectural completion;
• a full portal is planned;
• the entrance form itself requires a different center;
• the facade already has a different main ornament.

Then it's better Buy Polyurethane Molded Decoration after a new selection, rather than trying to use a specific article at any cost.

Practical scenario: a small entrance door in a one-story house

Let's say the entrance has an external width of about 1200–1400 mm.

Above it there is a relatively low free field.

The windows nearby are small.

The facade is not overloaded.

Here the first fitting is NPU-382 297 × 404 mm.

The larger version is also being tested, but it is the compact option that has a good chance of maintaining lightness.

If one overlay is clearly readable, the molding may not be needed at all.

Scenario: wide entrance with a double door

The architectural width increases significantly.

297 mm may become too intimate.

338 × 406 mm is being tested.

If it too gets lost, the next step is not to automatically look for an even larger NPU-382, which does not exist, but to check MLDPU-002 as a way to expand the architectural field around the central ornament.

Scenario: door under a high canopy

NPU-382 cannot be selected based on a photo of the wall.

Visibility from under the canopy must be taken into account.

It is better to temporarily install the template at the actual point and look:

• from the path;
• from the steps;
• from the side;
• in the evening under existing lighting.

If the lower position is hidden, the center may need to be raised.

Scenario: NPU-382 on the pediment above the entrance

Here the main problem is distance.

From ground level, the detail appears significantly smaller.

First question:

Is the pattern visible at all?

If not, a single overlay does not solve the problem.

Then you need to either add architectural lines or choose a different pediment design system.

Scenario: a classic door is already surrounded by rich stucco molding

Perhaps NPU-382 is not needed at all.

If the top of the opening already has a pediment, keystone, or other centerpiece, another large overlay will create duplication.

A good purchase starts with the ability to refuse the unnecessary.

Scenario: a completely smooth facade of a modern house

Here, first create a visualization.

A single NPU-382 can become an expressive eclectic detail.

But without repeating the classical plasticity in other parts of the entrance, the risk of randomness is high.

Adding MLDPU-002 may help, but it could further alter the stylistic approach.

You need to decide whether you truly want to introduce a classical motif, rather than just filling an empty space.

The decor above the entrance should be visible both when the door is closed and when it is open.

It would seem that opening does not affect the facade overlay.

Mechanically, indeed, it does not, if the element is located on the wall.

But visually, an open door changes the composition of the entrance.

If the door leaf has a bright interior color, glass, or noticeable texture, NPU-382 should remain the top center, not compete with the new plane.

This is already a subtlety, but for a front entrance it matters.

Why one NPU-382 is especially good when reconstructing a finished facade

Building a complex portal on a completely finished wall is a much more serious task.

You need to rethink:

• lines;
• junctions;
• the number of elements;
• painting;
• the entire entrance architecture.

One overlay reduces intervention.

If the facade does not require a complete rebuild, but only one missing center, this option looks rational.

That is why the topic is not reduced to "saving on decor."

This is about the scale of changes.

New construction: it's better to install NPU-382 before finishing touches

If the house is only being designed, there is an advantage.

You can determine in advance:

• the exact axis;
• height;
• the dimensions of the framing;
• the place for the molding;
• the overall color scheme.

Then NPU-382 is not "added to free space."

The free space is immediately calculated for it.

In such a situation, the NPU-382 + MLDPU-002 combination is especially convenient for preliminary design.

How NPU-382 differs from a random decorative panel

The main advantage of choosing a specific catalog item is the known dimensions.

We have:

• 297 × 404 × 18 mm;
• 338 × 406 × 18 mm.

You can make a full-size template.

You can calculate the field.

You can compare with MLDPU-002.

You can determine the amount of molding.

With an abstract "beautiful decor around 40 cm" there is no such precision.

Do you need to buy two versions for fitting?

Not necessarily.

Dimensions are known in advance, so a preliminary visual fitting is easy to do with templates.

Buying two expensive overlays just to compare scale is irrational.

First, paper or cardboard.

Then, the specific size.

What to check right before ordering NPU-382

Not ten abstract design rules, but six specific points.

1. Free field size

Width and height.

2. Entry axis

Relative to what the overlay is centered.

3. NPU-382 size

297 or 338 mm in width.

4. Perception distance

How the part looks from the path and street.

5. Is MLDPU-002 needed

Is the center enough or is a line required.

6. Outdoor installation conditions

The base, preparation, adhesive, and finish must be determined before installation.

After that, the decision becomes much calmer.

How to buy on STAVROS via three routes

Route 1. Only NPU-382 is needed

After the template, it became clear that the central accent is sufficient.

Then you can buy the carved overlay NPU-382 of the required size.

Route 2. NPU-382 is needed along with the frame

A card opens molding MLDPU-002, the actual profile length and the number of planks are calculated.

Additionally, you can buy decor for molding MLDPU-002 after comparing compatible elements.

Route 3. A complete entry system is required

Then it is better not to assemble it with random transitions from one card to another, but first determine the composition and order polyurethane facade decor based on the finished composition.

FAQ: questions about NPU-382 above the front door

Can I use one NPU-382 without the MLDPU-002 molding?

Yes, if one panel visually completes the free space above the entrance. Compatibility with MLDPU-002 means the ability to build a more advanced system, not the mandatory use of the molding in every project.

Which NPU-382 size should I choose — 297 × 404 or 338 × 406 mm?

First, compare full-size templates directly on the facade. The first option is narrower and suitable for a more compact field, the second provides greater horizontal presence.

Why is the height of the two options almost the same?

Both versions have a height of about 400 mm. The main difference lies in the width: 297 and 338 mm. Therefore, the choice especially depends on the width of the architectural field above the door.

How much does the NPU-382 cost?

Size 297 × 404 × 18 mm — 8,930 ₽, size 338 × 406 × 18 mm — 9,420 ₽.

What material is the NPU-382 made of?

made of polyurethane.

What is the relief of the NPU-382?

Both specified versions have a depth of 18 mm.

What does "molding overlay MLDPU-002" mean?

NPU-382 is provided in a decor system compatible with MLDPU-002. This allows building a composition from a central carved element and a linear molding.

What is the size of MLDPU-002?

22 × 11 × 2600 mm.

How much does MLDPU-002 cost?

The current indicated price is 5,460 RUB per strip.

Can NPU-382 be placed directly above the casing?

Such a layout can be considered, but the overlay should not visually press against the frame. The exact distance is determined by the total height of the field and checked with a template.

Is it necessary to center NPU-382 strictly on the door?

In a symmetrical entry group, one usually starts with the axis of the door and its entire framing. If the facade architecture is asymmetrical, the axis of the larger facade block may turn out to be the main one.

How can you tell that one overlay is too small?

Step back to the usual approach distance to the house. If the NPU-382 turns into a barely noticeable point and does not hold the upper part of the entry composition, the scale is insufficient.

What to do if the NPU-382 seems small, but another size is almost the same?

Try not to add a second overlay, but to structure the MLDPU-002 field. Often the problem is solved not by enlarging the center, but by the appearance of an architectural line around it.

Can two NPU-382s be used above one door?

Only if the facade really has two independent symmetrical fields. For a typical central entry composition, one overlay is usually more logical.

Will the NPU-382 suit a pediment?

It can be considered as a central decorative element, but the scale needs to be checked from ground level. On a large or high pediment, a single overlay may turn out to be visually too small.

Does NPU-382 replace a ready-made pediment?

No. It is a carved decorative overlay, not a complete architectural pediment system.

Can a frame be made around it from another molding?

Theoretically, compositions can vary, but NPU-382 has a confirmed connection with MLDPU-002. If a different profile is considered, its dimensions and stylistic compatibility need to be checked separately.

Can NPU-382 be painted in the color of the facade?

The color scheme can be built tone-on-tone if the chosen finishing system is suitable for polyurethane and outdoor conditions. Specific preparation and coating materials need to be agreed upon before installation.

And contrastingly?

It's possible if the contrasting color is already supported by other parts of the facade. A single brightly highlighted overlay on a calm wall may look too isolated.

What matters more—the size of the door or the size of the free field?

Both parameters. The door sets the central axis, and the free field determines the scale of the decor.

Do we need to take into account the windows near the entrance?

Yes. They affect the boundaries of the entry group and the perceived scale of NPU-382. This is especially noticeable with symmetrical windows on either side of the door.

How to calculate the quantity of MLDPU-002?

Add up the lengths of all sections of the future frame or line and compare the result with the length of one plank — 2600 mm. Then take into account the actual cutting and joining scheme.

Do I need to buy MLDPU-002 at the same time as NPU-382?

Only if the project has already confirmed that a molding line is needed. If one NPU-382 works well on its own, there is no point in buying an extra profile.

Can NPU-382 be used on a completely smooth modern facade?

It can be considered as a deliberate classical accent, but the stylistic connection with the front door and the rest of the house needs to be checked. On a completely neutral facade, an intricate carved element may look random.

When is it better to choose different decor?

When both sizes of NPU-382 do not match the scale, the pattern does not suit the architecture, or the entrance requires a completely different system. Then it makes sense buying polyurethane molding decor after comparing other elements.

Is a full pilaster needed on the sides of the door?

Not necessarily. Pilasters are only needed where the composition requires strong vertical supports. For a calm entrance, NPU-382 and, if necessary, MLDPU-002 may be sufficient.

What should be used to secure NPU-382?

The specific mounting compound is chosen based on the overlay material, the base, and the installation conditions. Before starting work, you can review the material molded decoration adhesive and clarify the requirements for the exterior facade.

Can I order one NPU-382 first and add the molding later?

Yes, but it is more rational to model both options in advance. If the molding is almost certainly needed, it is better to calculate its layout right away to understand the final composition.

Final check: is one NPU-382 enough, or is it time to add the molding?

Before purchasing, stand opposite the entrance with the installed template and answer five questions in sequence.

Is the ornament visible from the point where you usually approach the house?

If not, one element is not enough.

Is it connected to the door?

If NPU-382 seems like a separate piece in the middle of the wall, a molding line may be needed.

Is there enough calm background around?

If the element is squeezed by trim, cornice, and neighboring details, the problem is the opposite — there is already too much decor.

Does the scale of NPU-382 match the rest of the facade?

On a small house, one overlay can be a strong center. On a large one, it can be barely noticeable.

After trying it on, do you want to add something else precisely because the composition is unfinished, or just because the catalog has many beautiful details?

These are two completely different desires.

The first is a reason to design a system.

The second is a reason to stop.

When one carved overlay NPU-382 is truly enough

The answer can be formulated quite precisely.

One NPU-382 is sufficient when the entrance architecture already exists, and it only lacks the central decorative finishing touch.

The door has clear boundaries.

The trim or the geometry of the opening itself forms the lower part.

The free field above the entrance is not so large that the carved element gets lost.

The 297 × 404 or 338 × 406 mm template is confidently readable from a normal distance.

The ornament supports the style of the house.

Enough calm surface remains around it.

In such a situation, there is no point in artificially turning one clear task into a large facade project. You can order NPU-382 made of polyurethane and make it a standalone accent.

If, after a full-size fitting, the overlay seems correct in pattern but does not merge with the door, the most natural next step is MLDPU-002.

And if even the combination of NPU-382 + MLDPU-002 looks too intimate relative to the building, then the problem is no longer with the specific overlay. The facade requires an architectural system of a different scale.

This is the reasonable commercial choice: not to buy maximum decor, but to determine the minimal set that truly completes the house.

STAVROS allows you to go through this path sequentially: start with a specific NPU-382, compare two real sizes, if necessary select a compatible MLDPU-002, look at another Decor for polyurethane moldings or move to a more developed facade composition.

Sometimes architecture really needs a portal.

Sometimes it needs a molding.

And sometimes the free field above the door asks for exactly one thing — a correctly chosen, precisely centered carved NPU-382, around which enough facade remains for its relief to work independently.