Kitchen installation is already scheduled, and Myron HL-039 is without coating: which order will make it in time for installation

Installers will arrive on Friday. The facades are ready, the countertop is installed, the appliances are waiting for connection, and the holes for the handles are marked. All that remains is to pick up the furniture fittings and finish the kitchen. The buyer opens the Myron HL-039 card, sees the availability mark, places the order, and considers the issue resolved. The handles do arrive on time — neatly sanded, with fasteners, in the required quantity. But the surface remains unpainted. It's too early to install them in the kitchen.

Product availability in stock only answers the question about the availability of the wooden blank itself. It does not mean that the handle has undergone final finishing, gained coating strength, and is ready for constant contact with wet or dirty hands. Myron HL-039 is supplied unpainted. Before installation, you need to choose a finishing system, make a test coat, treat the entire batch, and allow the technological drying specified by that system. The duration of such a cycle cannot be guessed by the calendar: it depends on the specific primer, enamel, oil, varnish, number of operations, and application conditions.

That is why the request to buy Myron HL-039 should be considered together with the installation date. Fast shipment of an unpainted handle can solve the task when there is a confirmed technological window between receiving the goods and installation. If the kitchen is handed over almost immediately, other routes are possible: postpone the installation of only the fittings, order the ready-made Myron HL-039M with factory coating, or choose another handle already prepared for installation and available in the required quantity.

In this fork, there is no single answer for everyone. The unpainted HL-039 gives freedom of color and allows you to match the handles with facades, countertops, furniture legs, or wooden decor. The ready-made HL-039M saves the finishing stage, but at the time of preparing the material, it is listed as a made-to-order item. So, the word "ready-made" does not yet mean "will arrive sooner." You need to compare two calendars: the time to receive the handle and the time to bring it to installation readiness.

To buy wooden handle Myron HL-039 without an unpleasant surprise, answer four questions in advance:

1. When will the handles be with the finisher?

2. What coating will be used?

3. When will it reach a state acceptable for installation and normal grip?

4. Who is responsible for the test coat, finishing, drying, and handing over the finished batch to the installer?

If at least one answer sounds like "we'll figure it out after delivery," the project calendar is not yet assembled.

Myron HL-039 Furniture Handle

from 9.66 $

Go to Catalog

Short answer: which option to choose for the scheduled installation

As of the check on August 2, 2026, the Myron HL-039, measuring 46 × 22 × 18 mm, is available in beech and oak, has "Prestige" sanding quality, is supplied unpainted, and the mounting kit is included in the price. The product card shows availability.

The Myron HL-039M has the same size of 46 × 22 × 18 mm, is made of oak with white, black, brown, or transparent coating. This version already has a finish, but as of the check date it is marked as a made-to-order item.

From this data, a practical choice follows:

• order HL-039 without coating when the product is available in the required quantity, the color must exactly match the project, and there is time before installation for a test coat, batch processing, and full technological curing;

• postpone the installation of handles if the facades themselves need to be installed now, but the HL-039 finish is not ready yet;

• consider HL-039M when one of the confirmed factory colors is acceptable and the production time fits the schedule;

• choose another handle with a coating from stock when the installation date is fixed, HL-039M cannot make it in time, and self-finishing HL-039 is impossible;

• do not temporarily install an unfinished handle planning to remove it later: the kitchen starts being used immediately, the wood gets dirty, and dismantling the entire batch becomes a separate job.

The decision is made not based on a single status of "in stock" or "on order," but on the date when the specific version will be ready for actual use.

Watch video ...

Two versions of Myron: same shape, different route to installation

HL-039 and HL-039M are related in design and size, but occupy different places in the project. The first is a prepared wooden handle without a finish coating. The second is an oak version with a ready color finish.

The difference is not just about price. The buyer either gets the freedom to finish it themselves, or a reduced list of work after receipt. But in both cases, a calendar is needed.

Our factory also produces:

Wooden socket R-002

from 4.83 $

Wooden Capital KL-004

from 24.74 $

Wooden Capital KL-010

from 136.63 $

Wooden capital KL-067

from 24.74 $

View Full Product Catalog

An unpainted HL-039 is not an unfinished handle

Delivery without coating is an independent commercial option. It is needed by designers, furniture makers, and private customers who require:

• to paint the handles in the exact color of the facade;

• to match the shade of furniture legs;

• to preserve the oak texture under a clear or tinted finish;

• to use their own proven finishing system;

• to produce handles and other wooden elements in one batch;

• to get the model from stock without waiting for individual factory coating.

The problem arises not in the unpainted handle itself, but in incorrect expectations. The buyer sees the finished shape and smooth surface, so mentally considers the product complete. However, sanding and protective finish are different stages.

HL-039M is not an instant replacement

The finished coating reduces work after delivery, but the handle may be made to order. If installation is scheduled in a few days, waiting for the finished version may take longer than finishing the available HL-039 yourself — or, conversely, it may turn out to be the only realistic solution if the customer has no painter and no conditions for applying the coating.

Before order Myron HL-039M with finished coating, compare the confirmed readiness date with your installation schedule. Do not rely only on the average time: the specific batch and chosen color matter.

Size 46 × 22 × 18 mm: a compact handle also requires fitting

Myron belongs to button handles. It has one mounting point and a compact volume. The confirmed dimension line is 46 × 22 × 18 mm. The letters of the dimension scheme must be read according to the DWG, so you cannot rename each number yourself without a technical drawing. For the buyer, the full size and the actual position of the handle on the facade are important.

The compact shape is convenient for small doors, furniture drawers, cabinets, and wardrobes. But a "small handle" does not mean "fits anywhere." On a narrow facade, it may look proportionate, but on a wide kitchen drawer, it may get lost or become inconvenient to open.

The scale is checked on the facade, not in the palm

When you hold the handle separately in your hand, it seems noticeable enough. After installation on a tall cabinet or wide drawer, its scale changes. This is especially felt on calm, monochrome facades, where every hardware point forms a rhythm.

Before ordering, print the front contour at 1:1 scale or cut out a paper mockup. Place it:

• on the upper doors;

• on the lower fronts;

• on the narrow drawers;

• on the widest drawer;

• on the front of the built-in refrigerator, if the same model is planned there;

• on the cabinets of the tall unit block;

• on the island.

A photo of the entire kitchen with temporary templates will show whether to use one knob, two handles on a wide front, or a different model.

One hole simplifies marking, but does not allow mistakes

A knob handle does not require a center-to-center distance between two points. This makes installation easier on new furniture and replacement of old single-point hardware. But the center of the hole becomes especially noticeable: shifting one handle disrupts the line of the entire row.

Before drilling, mark:

• indent from the door edge;

• installation height;

• common line on adjacent fronts;

• position relative to the panel, frame, or milling;

• distance to the drawer edge;

• grip convenience;

• absence of conflict with the adjacent door.

The fastener fits, but the front thickness is still checked

Card HL-039 confirms the mounting kit. The buyer does not need to automatically add a random screw. However, the presence of the kit does not cancel the check of the specific front.

Before installation, the technician must know:

• thickness of the door or drawer;

• presence of a thickened frame;

• sampling depth from the inner side;

• facade material;

• working length of the complete fastening;

• possibility of full tightening without damaging the handle;

• size and condition of the existing hole when replacing old hardware.

If the fastener does not fit a specific thickness, the solution is agreed upon before installation. Random washers must not be placed or the screw shortened without checking the assembly.

Delivery date and readiness date are two different events

The kitchen schedule usually marks cabinet production, countertop installation, appliance connection, and installer visits. Handle finishing remains outside the calendar because it seems like a minor operation. In practice, it is precisely this that can halt the final stage.

Order HL-039 has several dates:

1. processing and confirmation;

2. shipment;

3. receipt;

4. unpacking and acceptance;

5. trial assembly;

6. test coating;

7. shade approval;

8. processing of the entire batch;

9. interoperational holding;

10. final coating formation;

11. transfer to installer;

12. installation.

The delivery date is roughly in the middle of the chain, not at its end.

The "in stock" status shortens only part of the path

An item from the warehouse doesn't need to be produced from scratch if the required quantity is actually available. But after receiving it, there remains work that depends on the buyer and their contractors.

If the handles arrive on Tuesday and installation is scheduled for Wednesday, a full coating cycle can only be completed with a pre-selected system, a ready sample, an available finisher, and a confirmed technology. In most unprepared projects, one evening is not enough.

Dry to the touch and ready for use are not the same

The surface may stop being sticky but still not have gained the properties needed for tightening fasteners and constant finger contact. Early installation creates risks:

• hand marks;

• tool dents;

• packaging imprints;

• damage around the fastening area;

• sticking of parts;

• difference in gloss after local touch-up;

• contamination of the still soft surface.

The exact period is determined by the instructions of the selected coating system. A universal number for enamel, varnish, and oil would be incorrect.

Count the schedule backwards from installation

The correct calendar is built in reverse order.

Installation date
minus confirmed coating curing time
minus time for applying all layers and inter-operation pauses
minus time for test application and approval
minus time for acceptance and test assembly
minus delivery time
equals the last safe date for placing the order.

If the result is already in the past, the original route is too late. Then you need to change not the technology to a random fast one, but the solution: postpone the installation of handles, choose a ready-made option, or look for another model from stock.

First route: buy Myron HL-039 without coating and manage to complete the finishing

The unpainted version fits the scheduled installation when all project participants act not sequentially, but in parallel. While the kitchen is being produced, the color sample, coating system, and responsible craftsman are being approved. By the time the handles arrive, the finishing is no longer discussed — it is launched.

Before placing the order

Prepare a facade map and the exact number of handles. Choose beech or oak. Decide whether the surface should be opaque or preserve the texture. Agree on the finishing system with the contractor and get a real technological schedule from them.

Before the purchase, the following must be known:

• color;

• gloss level;

• material HL-039;

• number of handles;

• one or two buttons on wide drawers;

• need for a spare part;

• work location;

• date of batch transfer to the installer;

• marking method;

• procedure for treating the mounting area.

After that, you can buy Myron HL-039 without coating and book a slot in the finishing schedule in advance.

On the day of receipt

Do not hand over a closed box to a painter or installer. First, perform acceptance.

Check:

• quantity;

• size 46 × 22 × 18 mm;

• beech or oak;

• sanding quality "Prestige";

• availability of mounting kits;

• absence of damage;

• consistency of shape across the entire batch;

• marking;

• DWG and compliance with the project.

If twenty handles are ordered, you need to see twenty items and twenty confirmed mounting kits. A shortage discovered after painting disrupts the batch shade and the schedule.

Test installation before coating

One handle is tried on a facade sample or on an approved test door. Such a check answers questions that cannot be resolved on screen:

• is the grip comfortable;

• does the included mounting hardware fit;

• does the handle not turn;

• does the base cover the existing hole;

• is the height correct;

• is the model proportionate to the facade;

• does the hand not touch the adjacent edge;

• is one or two buttons needed on the wide drawer.

The check is performed before finishing to avoid damaging the finish and not painting an unsuitable batch.

Test paintout

The coating is tested on one handle or a prepared sample of the same wood species. A flat board is useful but does not fully convey the look of Myron: light reflects differently from the face, sides, and shape transitions.

After application, the sample is evaluated:

• in daylight;

• with kitchen lighting on;

• near the facade;

• next to the countertop;

• near metal equipment;

• with dry and clean hands;

• after the full completion of the technological cycle.

The color before drying may differ from the final result. It cannot be confirmed immediately after application.

Processing the entire batch

Handles are marked so as not to mix the trial, reserve, and main items. The coating is applied in a single cycle, following the technology of the selected system.

Do not paint half of the set today and the second half a few weeks later without necessity. Different batches of material, temperature, and application technique can change the shade or gloss.

Curing before installation

Readiness is determined not by the customer's impatience, but by the requirements of the finishing system. Handles must withstand:

• packaging;

• transportation;

• tightening of the fastening;

• installer's touch;

• normal opening of the facade;

• regular cleaning in the future.

If the finisher does not confirm readiness, the installation of handles is postponed. Installing a kitchen without face hardware is usually easier than restoring damaged coating on the entire batch.

Second route: order HL-039M with factory coating

The finished version is convenient when one of the four colors matches the project:

• white;

• black;

• brown;

• transparent.

HL-039M is made of oak. The buyer does not have the stage of independently selecting the primer, applying the color, and curing after home or third-party finishing. After receipt, only acceptance, fastener inspection, and installation remain.

But this saving of operations has a condition: the product must arrive in time for the project.

First, confirm the timeline for a specific batch.

At the time of preparing the article, HL-039M is marked as a made-to-order item. The average timeline indicated in the product card is useful for orientation, but the agreement should relate to:

• the required quantity;

• the selected color;

• date of issue;

• delivery city;

• receipt method;

• time buffer for inspection.

You cannot order ready-made coating a day before installation just because self-painting is already too late.

Factory color is also checked physically

A white facade and a white handle may differ in tone. Black can be neutral, cool, or warm. Brown must interact with wooden surfaces. Transparent coating shows the natural texture of oak, which does not have to repeat the pattern of an adjacent part.

The screen displays the shade approximately. For a responsible project, a sample or preliminary approval of acceptable difference is required.

When HL-039M is more practical

The ready-made version is especially convenient if:

• no reliable finisher available;

• no space for safe drying;

• the selected factory color is suitable;

• a small quantity is required;

• handles must be ready without additional transfer between contractors;

• the apartment is already occupied;

• painting on site is undesirable;

• production timelines are confirmed;

• the kitchen will be actively used immediately after installation.

When HL-039 remains preferable

The unpainted version wins if you need:

• an exact facade color;

• a non-standard shade;

• one system with wooden legs or decor;

• a special level of gloss;

• preserving the oak texture with custom tinting;

• your own proven technology;

• an in-stock item with enough time for finishing.

Third route: install the kitchen now, and the handles — after the coating has cured

Kitchen installation and mounting of face hardware do not always have to happen on the same day. If the cabinets, facades, countertop, and appliances are ready, but the handle coating is still curing, it makes sense to split the stages.

This option requires coordination with the furniture maker.

What needs to be decided in advance

• whether the facades will be drilled at the factory;

• who stores the fasteners;

• who will come to install the handles;

• whether a repeat visit is included in the contract;

• whether the handles can be installed independently without losing the warranty;

• how to protect the finished holes;

• where to store the painted batch;

• who will check that the quantities match.

If the holes have not been made yet, moving the handles does not mean that drilling can be done later without a template. The layout is still approved together with the furniture.

Why this is better than temporarily installing raw wood

Temporary installation creates false convenience. The kitchen starts working, the handles absorb dirt, and then the entire batch has to be removed. Fasteners can get mixed up, holes can get extra stress, and the finisher will have to clean the surface.

It is much cleaner to leave the fronts without handles for a short agreed period or use a technical opening method provided by the furniture maker.

A repeat visit should be part of the schedule

The phrase "we'll screw them on later" is too vague. Set a date, a responsible person, and readiness conditions. Otherwise, the handles will stay in the box for several weeks, and the kitchen will be inconvenient to use.

Fourth route: choose another ready-made handle from stock

Sometimes it is more important for the project to finish the kitchen by a certain date than to keep exactly Myron. If self-finishing HL-039 is not in time, HL-039M is on order, and moving the installation is impossible, it remains to pick another ready-made model.

In the category you can buy wooden handles with coating, having filtered the actually available items. However, the replacement cannot be chosen only by color.

Compare:

• mounting method;

• size;

• base area;

• hole position;

• grip convenience;

• projection above the facade;

• material;

• color;

• quantity in stock;

• completeness;

• correspondence to the already completed layout.

If the holes for Myron have not been drilled yet, the choice is freer. After drilling, the new model must fit the existing assembly.

Beech or oak: the material sets the finishing logic

HL-039 is available in beech and oak. The wood species affects the texture, color choice, method of matching with the facade, and the final result. This issue cannot be postponed until the paint shop.

Beech for opaque color

A beech handle is convenient to consider under enamel, when the wood grain should not remain the main decorative effect. This option allows you to connect the hardware with painted facades:

• white;

• gray;

• green;

• blue;

• terracotta;

• beige;

• any other project colors.

The expression "under enamel" does not mean applied enamel. It describes the intended further finishing. The buyer must still choose the system and complete the entire cycle.

Oak for visible texture

Oak is chosen when the handle should preserve the natural grain. A transparent or tinted finish highlights the fibers and makes each piece slightly different.

This material bonds well with:

• wooden countertop;

• oak veneer;

• open shelves;

• furniture legs;

• slat panels;

• natural parquet;

• with other oak elements.

Matching the wood species does not guarantee a complete match in shade. The color is influenced by the specific blank, finish, lighting, and age of the adjacent wood.

Oak under opaque enamel

Technically, the project may provide for painting oak with an opaque composition. But before ordering, you need to understand why a species with expressive texture was chosen if the grain will be covered. Perhaps beech would be more rational.

The decision may have a structural or production reason, but it must be deliberate.

Beech under a transparent finish

Transparent finishing of beech is possible as a design approach if its calm texture suits the furniture. You cannot automatically assume that beech is intended only for white enamel. But a sample is mandatory: the visual effect will differ from oak.

Comparison of materials

"Prestige" — surface preparation, not a protective coating

HL-039 has a "Prestige" sanding quality. This is a detailed preparation of the wooden surface. It facilitates subsequent finishing but does not create a protective layer.

The buyer can run a hand over the smooth part and decide that oil or varnish is not needed. Tactile smoothness is deceptive: the pores of the wood remain open.

On the page, you can explore how to choose the quality and preparation of wooden products. For ordering, it is important to distinguish three concepts:

• material — beech or oak;

• sanding — "Prestige";

• finish — a system that is yet to be applied.

Why you cannot apply a coating without inspection

Even a prepared surface is checked before work. During transportation, dust, traces of packaging, or accidental contamination may have appeared on it. Specific additional preparation is determined by the finisher.

It is not allowed to roughly re-sand the entire batch unnecessarily: this can change the edges, size, and character of the surface.

Sanding does not protect against hands

Smooth wood still comes into contact with skin oils, moisture, and household dirt. In the kitchen, the handle is used dozens of times a day. The grip area gradually darkens and becomes uneven.

A protective finish is needed not for shine, but for controlled use and cleaning.

Why installing HL-039 without a coating is risky

An unpainted handle can be physically screwed to the facade. That does not mean it should be done.

Hands leave marks

Wood absorbs moisture and oil from the skin surface. On light beech, dirt becomes noticeable especially quickly. On oak, it can unevenly emphasize the pores.

After that, a clear coating can set the stain. Before finishing, additional cleaning or sanding will be needed, and a consistent result across the entire batch will be harder to achieve.

The kitchen creates increased load

Handles are located near food preparation, the sink, the dishwasher, and household chemicals. They are exposed to:

• water;

• fat;

• flour;

• juice;

• steam;

• detergents;

• cosmetic creams from hands;

• household dust.

The untreated surface is not designed for convenient regular cleaning with a damp cloth.

Temporary use quickly becomes permanent

The buyer plans to remove the handles after two days, but the kitchen gets loaded with dishes, the move begins, the finisher is busy, and the repeated dismantling is postponed. After a month, each button looks different.

It is better to postpone installation than to create a debt of finishing on already used furniture.

Coating after use is more difficult

For an even result, all handles must be in a comparable condition. If some doors were used more often, the surface will be soiled unevenly.

Before the finish, the craftsman will have to restore the general preparation. This adds time and does not guarantee that a transparent system will hide the marks.

How to choose a coating and not miss the deadline

The article cannot assign one universal varnish, enamel, or oil. The choice depends on the wood species, color, kitchen conditions, the contractor's equipment, and the desired surface.

You can study, what coatings are used for wooden handles, and then agree on a specific system with the finisher.

Enamel

Enamel is needed when the handle must get an opaque color. Before starting the batch, they check:

• adhesion of the system to wood;

• primer;

• coverage;

• thickness of layers;

• preservation of geometry;

• gloss level;

• resistance to constant grip;

• compatibility with facade enamel.

You cannot simply give the painter the facade color code. The same composition on MDF and solid wood can look different, so physical comparison is required.

Clear varnish

The varnish preserves the texture and creates a surface protective layer. For the project, a matte, semi-matte, or other confirmed effect is chosen in advance.

The test sample shows:

• how much the wood darkens;

• whether the shade changes;

• is the contrast of the fibers increasing;

• how smooth the surface appears;

• what the grip area looks like.

Oil

The oil system highlights the wood and preserves a more natural tactile feel. However, the specific product, consumption, number of operations, curing time, and further care are determined by the composition manufacturer.

In the catalog you can choose oil for wooden handles, however, the presence of the material next to the Myron card does not make it a universal choice for any project.

Staining

The tinting stage changes the color of the wood, but by itself is not always the final protection. The system may include a subsequent finish. The order is confirmed by the technologist.

On oak, it is especially important to check the uniformity and contrast of the pores.

Coating in the color of the facade

The most demanding scenario. The handle and facade are made from different bases and have different geometries. To achieve visual unity, finished samples are compared after full drying.

Do not promise an absolute match based only on the shade name.

What to add to the order along with HL-039

The full cart depends on the selected route.

There is no need to mechanically purchase all items from the table. For example, a professional painter already has tools. A facade sample may remain from production. A spare handle is not needed for every project. The table shows questions, not a mandatory universal set.

For self-assembly, you can buy materials for installation and wood finishing, having verified each composition against the selected technology.

How many Myron to order for the kitchen

The quantity is calculated based on facades and the adopted layout scheme, not by the number of cabinets. One cabinet may have two doors and three drawers, while another may have one wide facade with two buttons.

Create a facade map

Record each moving part:

• upper door;

• lower door;

• drawer;

• dishwasher facade;

• built-in refrigerator;

• pull-out basket;

• the corner front;

• mezzanine;

• pencil case;

• island;

• sideboard section.

Next to it, indicate the number of pens.

One handle per door

For most small hinged fronts, the design often provides one handle. But the placement depends on the opening direction and the kitchen layout.

On paired doors, the points must be mirrored consistently.

One or two handles for a wide drawer

There is no universal width limit. The decision depends on:

• the weight of the drawer;

• the slides;

• mounting locations;

• grip convenience;

• composition;

• furniture manufacturer's recommendations.

Two buttons change not only convenience, but also quantity. If the kitchen has six wide drawers, switching from one Myron to two adds six more items.

Built-in appliances

The front of a dishwasher or refrigerator may require a different grip method. Do not assign a compact button without coordination with the cabinetmaker and the system manufacturer.

Quantity formula

Total quantity = sum of handles on all doors + sum of handles on drawers + handles on built-in fronts + approved reserve.

Example:

• 8 hinged doors with one handle each — 8;

• 4 narrow drawers with one each — 4;

• 3 wide drawers by two

  Wardrobe

  Moisture and grease load is lower, but tall fronts change the scale of Myron. One compact button can look too small or require awkward force.

  Make a mockup on the tallest door.

  Chest of drawers

  On small drawers, HL-039 looks expressive and does not require two holes. For a wide heavy drawer, one central button must be coordinated with the guide rail design.

  Bedside table

  Here the handle is viewed from close range. Surface quality, shade, and tactility are especially noticeable. You can use the same color as on the bed, or emphasize the oak texture.

  Furniture in the hallway

  Handles come into contact with wet or dirty hands. Leaving unpainted wood unprotected is risky.

  Children's furniture

  A compact button is convenient if placed at the right height and does not obstruct movement. Coating, mounting, and usage conditions are coordinated with the project. Unconfirmed promises about the safety of a specific finishing system cannot be made.

  Commercial furniture

  In a store, hotel, or salon, handles are used by different people. For such a project, coating repeatability, spare stock, and replaceability are important. A separate reference piece simplifies future repairs.

  How not to confuse Myron with any other wooden button

  The phrase "wooden knob handle" describes a type, but does not guarantee interchangeability.

  Compare:

  • external dimension;
  • protrusion height;
  • face shape;
  • base area;
  • fastening unit;
  • included screw;
  • the material;
  • presence of coating;
  • product status;
  • DWG;
  • quantity in stock.

  Two buttons with a diameter of about 46 mm can fit differently against the facade and feel different to the touch.

  Replacing an old handle

  If there is already a hole in the facade, check:

  1. its diameter;
  2. location;
  3. the condition of the material around it;
  4. the area of the mark left by the previous handle;
  5. facade thickness;
  6. the possibility of covering the damage with the Myron base;
  7. the length of the mounting.

  HL-039 can be mounted through a single point, but this does not mean it will automatically hide the mark of another model.

  Replacing a bracket with a button

  The bracket leaves two holes. One Myron will not close them automatically. Facade repair, a decorative solution, or other hardware will be required.

  Replacing Myron with another ready-made button

  Before drilling, this is a designer replacement. After drilling, checking the base and fasteners is added. If the area of the new handle is smaller, the old trace may remain visible.

  What does "handles needed for installation" mean

  This phrase is too general. Specify which exact stage is assigned.

  Installation of cabinets

  Handles may not be needed on the first day. Facades are installed later, so finishing still has time.

  Hanging facades

  Holes and handles may be required for final adjustment, but the specific order depends on the cabinetmaker.

  Final handover of the kitchen

  The handles must be completely ready, installed, and checked. There is no room left to postpone the finishing.

  Photo shoot

  The coating must not only dry but also look uniform under bright light. Any difference in gloss will be noticeable.

  Moving

  The kitchen will be used immediately. Installing unfinished wood is especially risky.

  Ask the contractor to specify the exact date when the handles must be ready in his finished form, not the date of the general start of installation.

  Four practical calendars

  Calendar A: the kitchen is installed in a few weeks

  There is time for a deliberate path HL-039.

  Procedure:

  1. confirm the quantity;
  2. get one test handle or the entire batch;
  3. check the fasteners;
  4. agree on the color;
  5. perform a test paint;
  6. process the set;
  7. let the coating cure;
  8. hand over to the installer.

  The main risk is spending the time buffer on discussing the color and starting the finishing at the last moment.

  Calendar B: installation in a few days, finisher is ready

  HL-039 may only make it after written or clear confirmation of the technology and timeline. The curing time cannot be shortened for the sake of the calendar.

  Useful in advance:

  • submit a facade sample;
  • prepare the material;
  • book the work;
  • get handles directly from the supplier;
  • eliminate unnecessary transportation;
  • set a control completion date.

  If the contractor has doubts, another route is chosen.

  Calendar B: installation tomorrow

  Self-finishing from scratch should practically not start with a promise to "quickly dry something." The following are considered:

  • transfer of handle installation;
  • finished model from actual stock;
  • technically permissible temporary scheme without installation of face fittings.

  HL-039M will also help only with confirmed immediate availability, which cannot be assumed.

  Calendar G: kitchen already installed

  HL-039 can be safely finished separately, without subjecting the facades to painting work. The difficulty is temporary use of furniture without handles.

  Coordinate safe opening and do not use random ropes, sticky tapes, or temporary screws that could damage the surface.

  Acceptance of Myron batch

  Finishing must not begin until full inspection.

  Quantity

  Verify the order against the facade map. Separately count the reserve and samples.

  Material

  Beech and oak must not be mixed in one batch accidentally. Check the marking of each set.

  Size

  Confirmed line — 46 × 22 × 18 mm. If in doubt, compare the product with the DWG.

  Sanding

  Check the overall surface condition before applying the compound. Note any remarks immediately.

  Mounting

  The set is included in the price of HL-039. Recalculate it and perform a test on a facade sample.

  Geometry

  The handle must fit the test surface predictably. Do not try to fix the issue by over-tightening.

  Damage

  Chips, dents, and transit marks are assessed before painting. After applying the finish, it is harder to determine when the damage occurred.

  Storage of handles before finishing and installation

  Small parts are easy to lose, mix up, or get dirty.

  Do not keep them loose

  Divide:

  • main handles;
  • trial;
  • reserve;
  • already processed;
  • awaiting finish;
  • fasteners.

  Do not take workpieces with dirty hands

  Grease marks can show through transparent coatings. Use clean working conditions appropriate to the finisher's technique.

  Do not put fresh finish into a common box

  Surfaces may come into contact and get imprints. The drying and packaging method is determined by the contractor.

  Keep the labeling

  It will be needed when checking the material, quantity, and possible inquiries regarding the order.

  Installation after full completion of the coating

  When the finisher confirms readiness, the handles are handed over to the installer in protective packaging.

  First, one control position

  Install the first HL-039 on a test or low-visibility facade and check:

  • tightening;
  • fit;
  • no rotation;
  • preservation of the coating;
  • grip comfort;
  • position relative to the line.

  Only then proceed to the entire batch.

  The tool must not touch the face surface

  When tightening, protect the handle from scratches and impacts. Fastening goes from the facade side according to the provided scheme.

  Do not overtighten the joint

  Excessive force can damage the wood, coating, or facade. The specific tightening torque is determined by the design, not intuition.

  Check the line as you work

  After each group of facades, step back to a distance. A template error repeated twenty times becomes an expensive rework.

  Do not fix a chip with a local random color

  If the finish is damaged, use an approved repair system. Touching up with a different material will create a spot in color or gloss.

  What to choose for different facades

  Situation	Suitable route	Why
  Painted facades in non-standard color	HL-039 from beech under agreed enamel	Handles can be matched to the exact project shade
  Oak veneer and wooden countertop	HL-039 from oak under transparent or tinted system	Texture is preserved
  White kitchen and urgent installation	Ready white handle with confirmed availability	Self-painting is excluded
  Black kitchen with a tight deadline	Ready black finish or another model from stock	The actual delivery date is important
  Restoration of a chest of drawers	HL-039 without coating after trial selection	Color can be adapted
  Small bedside table	One or two HL-039 after the mock-up	Compact button proportionate to small fronts
  Wide heavy drawer	Checking one or two buttons	The quantity depends on the design and convenience
  Commercial furniture	Covered batch and reserve	Maintenance is simplified
  No finisher required	HL-039M or another ready-made handle	An unpainted version will create an unfinished stage
  Installation cannot be postponed	Only actually finished and available hardware	The date is more important than the initial model choice

  Buyer's matrix: five questions before adding to cart

  Does the shape and size suit you

  If not, open the general catalog where you can Buy wooden furniture handles, and compare other models.

  Do you need a custom color

  If yes, choose HL-039 without coating and allow for the full finishing cycle.

  Does the ready color HL-039M suit you

  If yes, confirm the production and delivery time.

  Is there a technological window

  Not "a couple of free evenings," but a deadline confirmed by the contractor for a specific coating.

  Who is responsible for the result

  The buyer, the cabinetmaker, the painter, or the manufacturer. Responsibility must have a name and a date.

  Mistakes that cause handles to arrive on time, but the kitchen remains without hardware

  Mistake 1. Equating availability with readiness

  HL-039 is available, but supplied without painting.

  Solution: count the finishing time separately.

  Mistake 2. Finding out about the coating after receipt

  There is only one day left before installation.

  Solution: read the configuration before payment.

  Error 3. Install raw handles temporarily

  The surface gets dirty.

  Solution: move exactly the fittings, not the protective stage.

  Error 4. Buy enamel on the day of painting

  Color and compatibility are not verified.

  Solution: approve the system in advance.

  Error 5. Consider a dry surface completely ready

  The finish gets damaged during tightening.

  Solution: maintain the full technological period.

  Error 6. Choose beech or oak only by price

  The material is not related to the finish.

  Solution: first determine the visual result.

  Mistake 7. Expecting a ready color from the "under enamel" mark

  The handle arrives without a finish.

  Solution: separate preparation and painting.

  Mistake 8. Ordering HL-039M as an urgent item without checking

  The finished version is made to order.

  Solution: confirm the date of a specific batch.

  Mistake 9. Choosing white based on a photo

  It differs from the facade.

  Solution: compare physical samples.

  Error 10. Count cabinets instead of facades

  Not enough handle parts.

  Solution: create a map of each door and each drawer.

  Error 11. Forget wide drawers

  After installation, it was decided to install two buttons.

  Solution: approve the scheme before ordering.

  Error 12. Not ordering a sample handle

  The first paint test is done on the main batch.

  Solution: allocate a control part.

  Error 13. Not recalculating the fastening

  Shortage is detected at the installer.

  Solution: accept the kit immediately.

  Error 14. Not checking the facade thickness

  The complete screw requires a different solution.

  Solution: perform a trial installation.

  Error 15. Painting handles in batches on different days

  The shade or gloss differs.

  Solution: combine the visible kit.

  Error 16. Mixing beech and oak

  After a clear finish, the difference becomes obvious.

  Solution: check the marking.

  Error 17. Hand the handles to the painter without a facade sample

  The color is approved from memory.

  Solution: use a real reference.

  Error 18. Store blanks in bulk at the site

  The surface gets dirty and damaged.

  Solution: organize clean, labeled packaging.

  Error 19. Paint after temporary use

  Stains appear under the finish.

  Solution: do not use before treatment.

  Error 20. Installing soft covering

  The tool leaves a mark.

  Solution: get confirmation of readiness from the finisher.

  Error 21. Choosing an alternative handle after drilling

  The base and the hole do not match.

  Solution: approve the model earlier.

  Error 22. Not planning for a repeat visit

  The kitchen is installed, but there is no one to screw on the finished handles.

  Solution: set a date and responsibility.

  Error 23. Ordering exactly the current quantity without checking the project

  After changing the facade, one detail is missing.

  Solution: verify the final specification.

  Mistake 24. Buying a large random stock

  There are extra handles of a different shade left.

  Solution: the reserve must have a purpose.

  Mistake 25. Evaluating Myron only on a small sample

  On a tall cabinet, the button gets lost.

  Solution: create a mockup on all types of facades.

  Mistake 26. Using one option in the kitchen without checking built-in appliances

  A heavy facade is inconvenient to open.

  Solution: coordinate the fittings with the furniture maker.

  Mistake 27. Assign a universal varnish based on advice from the internet

  The system has not been tested on a specific project.

  Solution: rely on the manufacturer of the composition and the contractor.

  Mistake 28. Not saving the color recipe

  It is impossible to accurately reproduce a repeat order.

  Solution: keep the specification and a sample.

  Mistake 29. Confuse HL-039 and HL-039M in the invoice

  A version with a different surface condition arrives.

  Solution: check the full article number with or without the letter M.

  Error 30. Start from the delivery date

  The project does not account for preparation after receipt.

  Solution: count backward from operational readiness.

  Who is Myron HL-039 without coating suitable for

  Choose HL-039 when:

  • a custom color is required;
  • beech or oak is needed;
  • there is a professional finisher;
  • a test paint-out has been approved;
  • the installation schedule leaves a confirmed window;
  • handles are painted together with other wooden parts;
  • requires precise alignment with the facade;
  • the batch is available in the required quantity;
  • the buyer is ready to accept and check the mounting;
  • installation can be postponed separately from the kitchen.

  Whoever finds HL-039M more convenient

  The finished version is more rational when:

  • white, black, brown, or transparent options are suitable;
  • oak is needed;
  • there are no conditions for own finishing;
  • one wants to avoid handover between multiple contractors;
  • production time confirmed;
  • color physically checked;
  • after receipt, only acceptance and installation are required;
  • small volume order;
  • coating in facade color is not required.

  When both versions do not solve the task

  Need to choose another model if:

  • Myron is too small or inconvenient for the facade;
  • installation is scheduled earlier than possible delivery of HL-039M;
  • HL-039 does not have time to undergo finishing;
  • required quantity is missing;
  • the complete fastening set does not fit and the assembly cannot be modified;
  • the ready-made colors do not match;
  • there is no possibility to postpone the installation;
  • the existing holes require a different base area;
  • the kitchen needs a pull handle;
  • the project provides for a different opening method.

  In such cases, it is better to choose ready-to-install furniture handles based on actual availability rather than installing an unprepared HL-039 just to preserve the original choice.

  How to place an order without a hidden step

  In the application, specify:

  • Myron HL-039 or HL-039M;
  • size 46 × 22 × 18 mm;
  • the material;
  • color or absence of coating;
  • quantity;
  • reserve;
  • installation date;
  • city;
  • delivery method;
  • need for a control sample;
  • person responsible for finishing;
  • facade thickness for checking the fastening.

  Example for unpainted batch:

  Myron HL-039, 46 × 22 × 18 mm, beech, "Prestige", unpainted, mounting kit, 20 pcs., including one control and one spare. Enamel finish per approved facade sample. Perform a test paint before starting the entire batch. Installation after confirmed technological curing.

  Example for oak:

  Myron HL-039, 46 × 22 × 18 mm, oak, "Prestige", uncoated, mounting kit, 14 pcs. Transparent finish per sample. Accept wood texture variations before start.

  Example for finished version:

  Myron HL-039M, 46 × 22 × 18 mm, oak, black coating, quantity 16 pcs. Confirm readiness and shipping date before payment. Compare color with facade sample.

  After confirming the batch, you can check payment and delivery terms for handles and schedule receipt into the project's reverse calendar.

  Frequently asked questions about Myron HL-039

  Does Myron HL-039 come painted?

  No. The card indicates that the handle is supplied unpainted.

  Can HL-039 be installed immediately after delivery?

  Physically, mounting is possible, but for normal use, the wooden surface must first be protected with an agreed finish.

  What is included in the price of HL-039?

  The price includes a mounting kit.

  What is the size of Myron HL-039?

  The confirmed size is 46 × 22 × 18 mm.

  Is it a knob handle?

  Yes. Myron is a compact furniture knob handle with a single mounting point.

  What type of wood is HL-039 made from?

  made of beech and oak.

  What is the sanding quality of the handle?

  "Prestige".

  What does "Prestige" mean?

  This is detailed surface preparation, not an applied protective coating.

  Is there a handle in stock?

  As of the check on August 2, 2026, the card showed availability. The current quantity needs to be verified before payment.

  Where can I see the current price?

  In the Myron HL-039 card. The price depends on the selected material and current conditions.

  How does HL-039 differ from HL-039M?

  HL-039 comes without coating and is available in beech or oak. HL-039M is an oak version with a ready white, black, brown, or transparent coating.

  Are they the same size?

  Yes, the current cards indicate 46 × 22 × 18 mm.

  Is HL-039M in stock?

  As of the time of preparing the material, it is marked as an item to order. The status needs to be checked before placing an order.

  What color does HL-039M have?

  White, black, brown, and transparent.

  Can HL-039 be ordered in the color of the facade?

  Yes, the unpainted version allows for a custom system, but the result is confirmed with a test paint sample.

  How to achieve an exact white color?

  You need to compare the finished paint sample of the handle with the actual facade after full drying. The name or shade code is not enough.

  What to choose under enamel — beech or oak?

  Beech is often considered for opaque painting. Oak is chosen when texture is needed, although the final decision depends on the project.

  Can oak be covered with enamel?

  Such an option is possible, but you need to understand why to cover the pronounced texture. The decision is coordinated with the finisher.

  Can the oak be left uncoated?

  For a constantly used furniture handle, this is a risk of contamination and uneven surface changes. Coordinated protection is needed.

  What to cover oak Myron with?

  The choice depends on the desired color, tactility, and kitchen conditions. Transparent and tinted systems are possible, but the specific product is selected separately.

  What to cover a beech handle with?

  A common scenario is opaque enamel. The specific primer and finish system is determined by the finisher and material manufacturer.

  Will regular wall paint work?

  A random composition should not be used. The handle experiences constant contact and requires a coating designed for such a surface and operating mode.

  How long does the coating take to dry?

  There is no universal time. The specific system, number of layers, inter-operation intervals, and final curing must be considered.

  Can drying be accelerated with heat?

  Only if such a mode is allowed by the coating manufacturer. Unauthorized heating can damage the surface.

  The surface is already dry to the touch. Can we install it?

  Not necessarily. Dryness to the touch does not equal readiness for tightening and constant grip.

  Do I need to do a test coat?

  Yes, especially for the kitchen, a large batch, precise color, and a clear oak finish.

  Where should we do the test?

  On one handle or a sample of the same wood species. The real shape shows the result more accurately than a flat board.

  Can we use the test handle after approval?

  Yes, if it matches the batch, is fully cured, and is not damaged by the tests.

  Do we need to paint all handles at the same time?

  For a single visible batch, this is preferable. It makes it easier to achieve a uniform shade and gloss.

  Can we paint part now and part later?

  Only with conscious technology, but the risk of differences increases.

  Do we need to treat the back part?

  The finisher determines the coverage scheme for all surfaces, taking into account fastening and technology. The issue cannot be left until installation.

  How to store handles after painting?

  According to the system instructions and the contractor's recommendations, avoiding contact of fresh surfaces and contamination.

  Can untreated handles be installed for a week?

  It is better not to do this. Even short-term use can leave stains and complicate the transparent finish.

  What to do if the kitchen is already installed?

  Finish the handles separately, wait for full readiness, and install them later. Coordinate safe temporary opening of the facades.

  Can the cabinets be installed without handles?

  The installation order is determined by the furniture maker. Often, face fittings can be installed as a separate step, but this needs to be agreed upon in advance.

  How many handles are needed for one door?

  Usually, the project includes one button, but the location and quantity are confirmed by the furniture drawing.

  How many buttons should be placed on a wide drawer?

  One or two — depending on width, weight, guides, and design. There is no universal limit.

  How to count handles for a kitchen?

  Make a list of all doors and drawers, assign a quantity to each facade, add built-in appliances and a justified reserve.

  Do we need to count the cabinets?

  No. One cabinet can have several movable facades.

  Is a spare Myron needed?

  For a large kitchen, custom color, or commercial project, a spare part is useful. For a small cabinet, it may be optional.

  How many spare handles should be ordered?

  Usually, one control or backup item is considered, but the quantity depends on the scale and the cost of reordering.

  Is it better to buy a spare right away or later?

  Right away, it's easier to match the material and finish from the same batch.

  Is Myron suitable for a kitchen?

  Yes, as a furniture knob handle after choosing the right finish, mounting, and quantity.

  Is it suitable for a cabinet?

  Yes, but on a tall or heavy front, you need to check the scale and grip comfort.

  Is HL-039 suitable for a dresser?

  Yes. Especially for small and medium-sized boxes, if the design supports a single mounting point.

  Can it be placed on a bedside table?

  Yes. The compact size is good to check on a full-size mockup.

  Is it suitable for a built-in refrigerator?

  It cannot be stated automatically. A heavy facade and appliances require coordination with the cabinetmaker.

  Is Myron suitable for a dishwasher?

  The solution depends on the facade, mechanism, and ease of opening. A single compact button may be insufficient.

  Can the old button be replaced with HL-039?

  Yes, if the existing hole, facade thickness, base area, and mounting match.

  Will Myron cover the mark from the old handle?

  This depends on the size of the base of the old hardware. You need to apply the template.

  Can the handle-bracket be replaced with Myron?

  The bracket leaves two holes. Facade repair or another decorative solution will be required.

  Do I need to drill two holes?

  No. The knob handle uses a single mounting point.

  Where can I view the DWG?

  Technical materials are provided in the HL-039 card.

  Why is DWG needed for a compact knob?

  It shows the actual dimensions and mounting geometry, which cannot be accurately assessed from a photo.

  Will the included screw fit facades of any thickness?

  You cannot promise automatically. Perform a trial installation on a sample.

  Can the screw be shortened?

  Only after approval from the foreman. The fastening assembly should not be changed at random.

  Are additional plugs needed?

  For standard installation of HL-039, the mounting kit is confirmed. The need for other parts is determined by the project.

  What to check upon receipt?

  Quantity, size, material, grinding, surface, and mounting kits.

  When should comments be submitted?

  Before painting, drilling, changing fasteners, and installation.

  How to know if HL-039 will make it in time for installation?

  Add up delivery time, acceptance, test coating, all coating operations, and final curing. Compare the resulting date with handover to the installer.

  What to do if there isn't enough time?

  Reschedule the handle installation, order a ready-made version with a confirmed deadline, or choose another coated model from stock.

  Is the ready-made HL-039M always faster?

  No. It may be made to order. Compare the actual dates.

  What matters more: availability or coating?

  For installation, the combination matters: the product must be received, finished, cured, and checked.

  Can I buy one HL-039 for testing?

  Yes. Such an order helps check the size, grip, mounting, and color.

  How to order the entire batch after the test?

  Save the article number, material, size, sanding quality, coating recipe, and the approved sample.

  Where to see other wooden handles?

  In the main catalog of furniture handles.

  Where can I see only unpainted models?

  In this section you can buy unpainted furniture handles and compare available shapes.

  Where can I see handles with a ready finish?

  In a separate category of models with coating.

  Can Myron be combined with bow handles?

  Yes, if the project links them by material, color, and scale. The mixing should be shown on the facade layout.

  Can Myron be made contrasting?

  Yes. For example, oak texture can contrast with a solid-color facade, and a black finished version with a white kitchen. The result is checked with a sample.

  Where can I clarify delivery?

  On the payment and delivery terms page of STAVROS.

  What question should you ask the manager before payment?

  "What variant and quantity of Myron are actually available when the order is handed over for delivery, and what exactly is included in the set?"

  What question should you ask the finisher?

  "When after receiving the handles will you be able to do a test, finish the entire batch, and confirm the coating is ready for installation and permanent grip?"

  What question should you ask the cabinetmaker?

  "Is it possible to install the kitchen now, and the handles as a separate stage after the coating has fully cured?"

  What question should you ask yourself?

  "Is a precise individual color more important to me, or guaranteed readiness of the hardware by the appointed date?"

  The handle must be ready not for delivery, but for use.

  Myron HL-039 can be quickly obtained when the required quantity is in stock. But a box with unpainted handles does not yet complete the project. Before installation, the batch must undergo acceptance, fastening inspection, test painting, approved finishing, and full technological curing.

  If there is enough time before installation and an exact color is needed, ordering HL-039 in beech or oak is a strong approach: the handles can be matched with facades, wooden countertops, and other furniture details. When there is no finishing window, you need to check the lead time of the finished HL-039M or choose another coated model that is actually available by the required date.

  The main mistake is to cut down not logistics, but technology. You cannot declare the coating ready earlier, put untreated wood "for a couple of days," or paint the entire batch without a sample. The installation date should drive the choice of version, not force you to disrupt the order of work.

  STAVROS company offers Myron without coating and with a ready finish, categories of wooden knob handles, finishing materials, technical models, mounting kits, and delivery. The buyer just needs to assemble these options in the correct sequence: choose the shape and quantity, check availability, approve the material and color, allocate real time for preparation, and hand over ready-to-use hardware to the installer.