Molding MLD-063 or MLD-064 buy: 14 or 23 mm for furniture, wall panels and doors — which to choose

It's easier to choose between 14 mm or 23 mm molding when you start not with an enlarged profile photo, but with the actual size of the facade, door leaf, or wall frame. MLD-063 and MLD-064 have similar beveled geometry, are made from MDF, beech, and oak, and are supplied for subsequent finishing. However, on the finished surface they work differently: MLD-063 forms a narrow 14 mm line, while MLD-064 creates a more noticeable 23 mm contour.

The difference is 9 mm, or about 64% relative to MLD-063. For a long strip, this seems like a small change, but on a furniture facade it affects the free inner field, distance to the handle, frequency of frames, and how visible the decor is from the opposite side of the room. A narrow profile is easier to repeat on drawers and small doors; a wider one works more confidently on a tall cabinet, door, and large wall panel.

Buy thin molding MLD-063 with a width of 14 mm is suitable for a small facade, nightstand, chest of drawers, several nested frames, or furniture where there is already a noticeable handle and central decor. Buy wooden molding MLD-064 with a width of 23 mm is reasonable for a tall cabinet door, door leaf, large frame, and wall panel where the line should be readable not only up close.

MDF for both models is supplied in lengths of 2600 mm. Beech and oak are available in lengths of 1000 or 2400 mm. For MLD-063, the MDF cross-section is 14 × 8 mm, solid wood — 14 × 9 mm. For MLD-064, the cross-section is 23 × 8 mm, the same for MDF, beech, and oak. MDF and beech are more often chosen for enamel, oak — for tinting, varnish, or oil, when you need to preserve the wood grain.

View size and price of MLD-063 View materials, lengths and price of MLD-064 Buy wooden moldings for furniture, walls and doors Order a molding sample before purchasing a batch View STAVROS wooden trim

Go to Catalog

Confirmed specifications of MLD-063 and MLD-064

Direct comparison: thin line or confident contour

Our factory also produces:

View Full Product Catalog

Why a 9 mm difference changes the entire facade

The profile height affects not only the width of the visible line but also the size of the free field inside the frame. On a small door, MLD-064 may come close to the handle, edge, and hinge area, whereas MLD-063 will leave more air.

On a tall door, the situation is reversed: a thin 14 mm strip can get lost, especially with matte monochrome enamel. The 23 mm profile creates a more noticeable light-shadow break and is perceived as an independent part of the composition.

Beveled shape and chiaroscuro

Both moldings have a beveled profile. The slanted face catches light differently than a flat layout, so even a frame painted in the facade color does not completely blend with the surface.

MLD-063 casts a thin shadow noticeable up close. MLD-064 creates a wider light plane and reads from a distance. It is useful to check the choice under the lighting that will be in the room.

How to check the profile with painter's tape

Two test strips 14 and 23 mm wide are glued to the facade. The tape should follow the future outer contour, including corners and the offset from the edge.

After the mock-up, the door is examined up close, from a normal distance, and from the entry point of the room. This layout shows not the cross-section, but the real scale of the frame next to the handle, panel, and adjacent facades.

Full-size mock-up for a cabinet

On a tall door, it is useful to build the entire frame from paper strips rather than attaching a short sample. This helps assess the vertical rhythm, the width of the inner field, and the distance to the top and bottom edges.

If the cabinet consists of several doors, the mock-up is repeated on at least two adjacent facades. Frequent repetition enhances the visual weight of even the thin MLD-063.

MLD-063 for a small door

The compact profile is convenient where every few millimeters affect the composition. It leaves room for a handle, central insert, overlay, or veneer pattern.

On a small door, MLD-063 does not turn the frame into a heavy border. It is especially convenient to use in a series of cabinets, upper cabinets, and small modules.

MLD-064 for a tall wardrobe door

A tall door requires a line that does not disappear on the overall plane. MLD-064 forms a noticeable contour and helps visually pull together an elongated facade.

At the same time, the indentation from the edge and handle should be larger than with a thin profile. You cannot transfer the MLD-063 layout to MLD-064 without a new template.

How to choose a molding for a dresser drawer

A drawer is usually lower than a door, so the frame quickly eats up usable space. MLD-063 often looks proportional and leaves room for a handle in the center.

MLD-064 is suitable for large fronts or a dresser with one wide frame. Before ordering, you need to check that the handle is not too close to the profile.

MLD-063 on a cabinet

On a bedside or TV cabinet, a thin profile helps add relief without heavy classicism. It works well on several small doors and drawers.

If the cabinet is close to the viewer, the delicate line will be noticeable. For a large console viewed from afar, MLD-064 may be required.

MLD-064 on the console

A wide console facade can accommodate a more noticeable contour. The 23 mm profile ties the body geometry together and makes a monochrome surface more expressive.

On a narrow console, MLD-064 is checked especially carefully: the frame should not turn the facade into a tight strip around the handle.

Molding for door leaf

The door leaf has a large scale, so MLD-064 is usually read more confidently. It suits one or two large frames and creates noticeable chiaroscuro.

MLD-063 is appropriate for frequent patterns or on a light modern door. Both profiles cannot be used as a replacement for trim or structural strapping without separate calculation.

Molding for wall panel

On the wall, the profile is viewed from a greater distance than on furniture. MLD-064 forms large architectural fields well, while MLD-063 forms a frequent thin grid.

Before choosing, it is useful to read, View STAVROS wooden trim, and make a full-size marking on the wall.

Frequent thin frames on the wall

MLD-063 allows placing multiple fields without the feeling of a heavy grid. It is suitable for a small study, bedroom, hallway, and a wall with furniture.

The more frames, the stronger the overall decorative effect. Therefore, a thin profile does not mean an inconspicuous composition if it is repeated many times.

Large architectural fields

MLD-064 is suitable for a high wall and large rectangles that should be readable from the opposite side of the room. The 23 mm width helps the frame not get lost next to the baseboard, door, and large furniture.

Too frequent a grid of MLD-064 can overload the wall. It is better to reduce the number of fields and increase the distance between them.

One frame or several

One large frame requires sufficient visual weight. For it, MLD-064 is usually more convincing, especially on a wide door or panel.

Several nested frames are easier to build from MLD-063. It allows maintaining gaps and does not turn the surface into an alternation of wide stripes.

Can MLD-063 and MLD-064 be combined

Such a combination is possible if the profiles perform different roles. MLD-064 can become the outer main contour, and MLD-063 the inner thin frame.

If both moldings repeat the same pattern without hierarchy, the composition looks random. The layout should show which profile is the main one.

Outer and inner contour

For a two-level frame, the wider MLD-064 is logically placed on the outside, and the thin MLD-063 on the inside. This way the visual weight decreases towards the center.

The reverse scheme is only possible as a deliberate design technique. The distance between profiles must be large enough so that the bevels do not merge.

How to position the frame relative to the edge of the facade

The offset depends on the profile width, door size, and hinge position. The same offset is not suitable for MLD-063 and MLD-064.

First, mark the installation zone, then build the outer contour. The profile should not come too close to the edge where the fastening and base material may be weaker.

How to account for hinges

On the inner side of the facade are the hinge cups and fasteners. The outer frame should not provoke drilling or fastening in a conflict zone.

Before installation, compare the markings with the inner side of the door. This is especially important for narrow frames and facades with small thickness.

How to account for the handle

The handle should remain an independent functional part. There needs to be visual breathing room and free space for fingers between it and the molding.

It's useful to learn Buy wooden moldings for furniture, walls and doors, and test the actual handle on a mockup, not just its dimensions.

Handle centered in the frame

If the handle is positioned in the center, the inner field must be large enough. MLD-063 more easily maintains a calm background around it.

MLD-064 may suit a wide facade, but on a small drawer it will come close to the handle. In that case, choose a thin profile or change the composition.

Handle at the edge of the facade

A vertical handle near the side edge competes with the side line of the frame. The distance between them and the ease of grip need to be checked.

Sometimes it's better to shift the frame inward or choose MLD-063. Installing MLD-064 according to old markings can make the edge too busy.

MDF 2600 mm long

MDF profiles of both models are supplied in 2600 mm lengths. Such a strip is convenient for tall doors and large wall frames because it reduces the number of longitudinal joints.

When cutting, transportation, workspace, and allowance for miter cuts are taken into account. A long plank does not guarantee a waste-free project without a cutting map.

Beech 1000 or 2400 mm long

A short 1000 mm plank is suitable for small facades and projects where a long leftover is not needed. The 2400 mm length is more convenient for tall doors and a series of frames.

Beech is more often chosen for enamel. Before ordering, you need to distribute all sides of the frames among specific planks and check where joints are acceptable.

Oak 1000 or 2400 mm long

Oak is chosen for its natural texture under tinting, varnish, or oil. The 2400 mm length reduces the number of joints on a large contour.

On short facades, 1000 mm can provide more rational cutting. But the wood grain and batch shade should be coordinated simultaneously for the entire project.

How to choose the length based on frame size

First, each side of the frame is calculated considering the corner joint method. Then, the segments are grouped by length and laid out on 1000, 2400, or 2600 mm planks.

Buying only by total linear footage is risky: theoretically, the length is sufficient, but the required long segment may not fit into the leftovers.

Why a cutting plan is needed

A cutting plan shows which plank each side will come from. It helps reduce waste and determine connection points in advance.

For solid wood, the direction and grain pattern are additionally considered. On an oak frame, a random combination of different sections may be more noticeable than on painted MDF.

Basic calculation of one frame

The net perimeter of a rectangular frame is equal to twice the sum of the width and height. However, the purchased length must account for corner cuts, test cuts, and possible errors.

For example, for a field of 600 × 800 mm, the net perimeter is 2800 mm. This does not mean that one plank of 2600 mm is sufficient.

Allowance for corner cuts

When joining at an angle, part of the length is used for setup and precise trimming. The more frames, the more repeated corners.

A single percentage allowance does not replace the layout across planks. For a complex pattern, it is better to calculate each segment and add a reserve for test cuts.

Calculation of multiple facades

For a series of identical doors, first calculate one frame, then multiply the number of sides and create a general cutting plan. Identical parts can be cut using a set stop.

Ordering the entire batch at once helps save material and maintain shade. A later purchase may differ in wood and preparation.

How to calculate nested frames

The outer and inner contours are calculated separately because they have different sizes and possibly different profiles. Then the segments are combined into a cutting map.

If MLD-064 is used on the outside and MLD-063 on the inside, you cannot add up the total length without separating by article and material.

Where to place the joint

The joint should not fall into the central visible part of the long side if it can be avoided. It is better to use a single plank for the most noticeable area.

On painted MDF, the joint is easier to hide with finishing, but it still requires precise preparation. On oak, the pattern makes the joint more noticeable.

How to avoid a joint on a tall door

For a side up to 2400 mm long, choose a full-size beech or oak plank. For MDF, a length of 2600 mm is available.

If the side is longer than the available plank, the connection point and technique must be specified in the project. You cannot simply join two pieces in the center without checking.

Why you can't just count meters

Two planks with a total length of 4800 mm may not yield the required four 1200 mm segments after accounting for cuts and waste. The arithmetic sum does not reflect the cutting geometry.

The customer should order not an abstract length, but a set of planks from which all sides can actually be made.

MDF for enamel

MDF has a uniform surface and is convenient for an even, opaque color. It is suitable for facades and wall panels that are painted without preserving the wood texture.

Ends and cut areas require proper priming. Without it, they may differ in absorption and gloss.

Beech under enamel

Beech is chosen when solid wood and a calm surface for an opaque coating are needed. After painting, it retains a joinery character, although the wood grain becomes less noticeable.

Beech and MDF cannot be considered completely identical under enamel: the material, edges, and reaction to humidity differ.

Oak under tinting

Oak is needed when the profile should show pores and natural grain. Tinting changes the color but does not hide the texture.

MLD-063 gives a thin oak line, MLD-064 a more noticeable wood stripe. On a large wall frame, the texture of MLD-064 reads more strongly.

Oak under varnish or oil

A transparent finish preserves the natural character of the wood. The choice between varnish and oil depends on the project's finishing system and usage conditions.

Specific durability cannot be guaranteed without documentation of the selected composition. A test sample is made before the entire batch.

Why oak under dense enamel is not always rational

An opaque coating hides the pronounced texture for which oak is often chosen. If the visual goal is an even color, MDF or beech may be more straightforward.

Oak under enamel is possible as a deliberate decision, but it should not be assigned solely due to the perception of a more valuable species.

Test swatch

A small section is painted with the full system: primer, intermediate preparation, and finish. The sample is held against the facade in daylight and artificial light.

For MLD-063, check that the thin bevel does not disappear in the color. For MLD-064, check that the contour does not become too heavy.

Painting before or after installation

Pre-finishing is convenient for even coverage of all visible edges. After installation, only joints and local areas need to be treated.

Painting an already assembled frame helps achieve a uniform color with the facade, but requires careful masking and control of glue joints. The solution depends on the project's technology.

Why you cannot paint only the front face

Side surfaces and bevels participate in light and shadow. An unpainted face will be noticeable from a side view.

Additionally, uniform finishing helps avoid differences in material perception. The coating scheme is agreed upon before cutting and installation.

How to prepare corners for enamel

Corner joints must be tight, and preparation should not destroy the bevel geometry. Excessive putty and sanding can flatten one corner.

First, a test frame is made, then the joining and finishing method is approved.

How to tint oak corners

On the cut, a different wood structure is revealed, so it may absorb the compound differently. The corner is checked on a test frame.

Attempting to hide an inaccurate joint with a large amount of tinting usually makes the spot even more noticeable. The geometry must be precise before finishing.

Prestige sanding

Cards confirm the quality of Prestige sanding. This means detailed surface preparation, but not ready enamel, varnish, oil, or tinting.

After transportation, the profile is inspected, dusted, and prepared according to the selected coating's technical data sheet.

How to choose mounting material

Glue and related compounds are selected based on the molding material and the base. You can View STAVROS wooden trim, but compatibility is still checked according to the specific compound's instructions.

MDF, solid wood, painted facade, and mineral wall require different conditions. A universal promise of one glue for all bases is incorrect.

Installation on a furniture front

The base must be clean, level, and capable of accepting the decorative profile. Marking is checked with the door closed and considering the hinges.

The molding should not interfere with opening, the handle, or the adjacent facade. Before the entire series, one control door is made.

Mounting on a wall panel

The profile is installed according to even markings, and the base is checked for strength and compatibility with the glue. Long lines require level control.

The wall frame should not be used to correct severe curvature without surface preparation. Molding is decorative, not a leveling structure.

Installation on the door leaf

It is necessary to check the door material, cladding thickness, and fastening zones. The profile must not interfere with the lock, hinges, or rebate.

Changes in the mass and geometry of the door leaf are assessed before installation. For a complex door, coordination with the manufacturer is required.

MLD-063 in modern classic

The thin beveled profile is well suited for furniture where the classic frame logic should look lightweight. It creates a neat contour without heavy ornamentation.

On light enamel, MLD-063 is read due to the bevel, not the contrasting color. This allows maintaining a calm surface and not overloading handles or overlays.

MLD-064 in modern classic

MLD-064 makes the frame more noticeable and is suitable for large cabinets, doors, and wall panels. It helps assemble a tall plane into an architectural contour.

The 23 mm profile is not equal to a wide classic cornice, but it can already become the main decorative element of the surface.

Molding in a neoclassical bedroom

On cabinets and bedside tables, MLD-063 supports a light frame system. MLD-064 is suitable for a high headboard, large door, or wall panel.

The profile color can be repeated on the facade or used as a wood accent. In both cases, check the scale next to textiles and lighting fixtures.

Molding in the living room

The living room is usually viewed from a greater distance, so MLD-064 is more often suitable for large wall fields and tall facades. MLD-063 works in details of a dresser, TV cabinet, and display case.

If both profiles are used in the same room, their roles should differ: wide for architecture, thin for furniture graphics.

Molding in the hallway

In a narrow hallway, a too-wide profile quickly overloads cabinets and doors. MLD-063 helps maintain lightness and leave room for handles.

MLD-064 is suitable for a single large panel or a tall door that should be an accent. Before installation, check passages and door swing.

Molding in the study

Oak MLD-064 under tinting can create an expressive frame on a wall panel or library cabinet. MLD-063 is convenient for drawer fronts and small doors.

With dark finishing, the bevel becomes more noticeable in side light. It is better to check lighting on a real sample.

Molding in children's furniture

For small fronts and frequent patterns, MLD-063 is more suitable. It leaves more free space and does not bring the frame closer to the handle.

Any decor must be securely fastened and not create sharp protruding areas. Safety is determined by the entire furniture structure, not just the profile.

Molding in the dressing room

Tall doors allow using MLD-064 as a confident contour, especially if the room is viewed from afar. On small drawers, MLD-063 works better.

A unified system of offsets helps connect different modules. You cannot use the same offset for profiles of different heights.

Molding in kitchen fronts

The kitchen requires particularly precise checking of handles, adjacent doors, and maintenance. MLD-063 is more often suitable for upper cabinets and small fronts.

MLD-064 can be used on a tall plinth or large decorative panel. The durability of the finish and adhesive in kitchen conditions is confirmed separately.

Molding for island

Kitchen island facades are larger and visible from all sides, so MLD-064 can create expressive fields. MLD-063 suits a frequent pattern or a calm modern composition.

Before installation, check the base, sockets, ventilation grilles, and service panels.

Molding on buffet

The buffet combines tall doors, drawers, and open sections. MLD-064 can highlight the main doors, while MLD-063 can support the drawers.

This combination only works with a common axis and coordinated offsets. Otherwise, the furniture looks like it's assembled from different series.

Molding on display cabinet

A glass insert already creates an active center, so the profile should not eat into its field. MLD-063 is often safer for thin framing.

MLD-064 suits a large display cabinet if the frame and glass maintain sufficient proportions. The method of attachment near the glass requires separate verification.

Molding around the mirror insert

Thin MLD-063 leaves more reflective surface and works well on a small facade. MLD-064 creates a strong frame around a large insert.

Molding does not replace mirror attachment. The panel, backing, and safety are calculated separately.

Molding next to a decorative overlay

If the facade has a large overlay, MLD-063 usually supports it rather than competes. MLD-064 requires more free space.

Useful to study Buy wooden moldings for furniture, walls and doors and build a composition to scale.

Molding next to a pilaster

A pilaster already forms a strong vertical. The thin contour of MLD-063 helps maintain hierarchy, while MLD-064 may be suitable on a very large body.

The distance between profiles should be sufficient so that the light and shadow do not merge into one heavy strip.

Molding near the cornice

The upper cornice has greater visual weight, so the facade frame should be subordinate to it. MLD-063 supports a light composition, MLD-064 a more architectural one.

To distinguish between part types, you can read, View STAVROS wooden trim.

How to choose a profile for a painted cabinet

On matte enamel, the beveled edge creates a shadow. MLD-063 gives a subtle graphic effect, MLD-064 a noticeable relief.

A test paint-out is needed in the actual color because dark enamel and light enamel show the bevel differently.

How to choose a profile for an oak cabinet

Oak texture enhances the decorative line. MLD-063 looks like a thin wooden insert, MLD-064 like a pronounced frame.

It is better to match the shade and pattern of the profile with the facade in one batch or through a physical sample.

How to choose a profile for an MDF facade

MDF profile is convenient to paint together with the MDF facade. The uniform base helps achieve an even color.

At the same time, cut areas and ends require proper preparation. Without primer, they may differ in gloss.

How to choose a profile for a solid wood facade

Beech or oak help preserve the joinery character. Beech is more often used under enamel, oak — under transparent finish.

The profile and facade can be made of different materials, but such a combination requires technical and visual verification.

How to make a test door

Before serial production, one door is assembled with molding, handle, hinges, and full finishing. It is checked in the cabinet, not on a separate table.

The test sample shows scale, convenience, joints, and color. After approval, the parameters are transferred to the entire batch.

How to mark parts during cutting

Each piece is labeled according to the facade and side: top, bottom, left, right. This reduces the risk of confusing lengths and wood grain.

For nested frames, the profile designation is added. MLD-063 and MLD-064 cannot be mixed in a common pile after cutting.

How to store planks before installation

Profiles are stored on a level support in a dry room, protected from impacts and construction moisture. Long planks cannot be left with sagging.

The material must adapt to room conditions according to the manufacturer's recommendations. Do not install wet or damaged profiles.

How to transport long planks

Lengths of 2400 and 2600 mm require a vehicle and packaging that do not cause bending. Planks are secured along their entire length.

Before ordering, check the elevator, staircase, and storage space at the site. Sometimes a short length of 1000 mm is more practical for small facades.

How to accept the profile

Check the article number, material, cross-section, length, sanding quality, and quantity. Inspect planks for damage and noticeable curvature.

Oak and beech parts are compared by shade before cutting. It's better to resolve issues before applying the finish.

How to store leftovers

Useful segments are marked and stored together with the finishing recipe. They will come in handy for repairs or color checks.

Short trimmings can be used as glue and finish testers, but they cannot be considered a replacement for a full-size frame sample.

Why you cannot buy an additional batch without checking

Solid wood may differ in grain and shade, and a technological batch of MDF may differ in preparation. A later additional purchase requires a new comparison.

For a large project, it is better to order the entire estimated volume and reserve at the same time.

What reserve is needed

The reserve depends on the number of corners, the craftsman's experience, the complexity of the cutting, and the length of the sides. A simple frame and dozens of nested frames require different approaches.

Instead of a universal percentage, a cutting map is created, and a strip or segments are added for test cuts and possible replacements.

Why 10–15% is not always enough

The percentage works as a guideline for simple linear footage, but does not account for long continuous sides. You may have a surplus in total but lack the required segment.

The cutting plan remains crucial for an accurate order.

How to calculate an example for one facade

Let the frame have an external size of 500 × 700 mm. The net perimeter is 2400 mm. But four corner cuts and adjustment require additional material.

One strip of 2400 mm formally equals the perimeter, but practically

Error: considering the difference of 14 and 23 mm insignificant

On a small sample, the difference seems small, but along the frame perimeter it changes the free field area and visual weight.

A full-size tape shows the result more accurately than a photo.

Error: select by large photo

Macro photography enlarges the thin profile and hides the scale. MLD-063 may appear as noticeable as MLD-064.

You need to look at the profile on the facade and from a normal distance.

Error: placing MLD-064 on a small door

A wide line may come close to the handle and edge, leaving a narrow inner field.

Before purchasing, check the 23 mm layout. If the composition is tight, choose MLD-063.

Error: using MLD-063 as the only contour of a huge panel

A thin frame may get lost on a large wall, especially with weak light and shadow.

For a large field, compare MLD-064 or increase the number of thin frames.

Error: not considering handles

After installation, the handle may be too close to the profile or interfere with grip.

The layout is built with the actual handle and opening is checked.

Error: do not account for loops

External decor may fall into the area of internal fasteners or weaken the edge of the facade if the technology is incorrect.

Matching both sides of the door is done before installation.

Error: use the same indent

An indent suitable for a 14 mm profile may be too small for 23 mm. The visual frame will become heavy and approach the edge.

Each profile receives its own marking.

Error: mixing profiles without hierarchy

Two different widths should create a main and secondary contour. Random alternation looks like a configuration error.

The layout should explain why each item is used.

Error: count only the clean perimeter

The clean length does not account for cuts, test cuts, and plank layout.

The order is built by segments, not just by total meters.

Error: forgetting material on corners

Each corner requires precise trimming and sometimes re-cutting. With zero margin, one mistake stops the project.

Reserve is planned before purchase.

Error: joining in a noticeable place

A joint in the middle of a long vertical or top side will be conspicuous.

Solid planks are used for main lines, and joints are moved to less noticeable areas, if they are allowed at all.

Error: considering beech and MDF the same under enamel

Both materials are suitable for covering color, but have different structure and edge preparation.

A test coat is needed for each material.

Error: using oak under dense enamel without reason

Enamel hides the pronounced texture of oak. MDF or beech may be more rational for an even color.

Oak is chosen when its properties and material are truly needed for the project.

Error: painting after installation without a test

Glue, seams, and different materials may show through the finish. Correction on finished furniture is more difficult.

First, assemble and paint a test frame.

Error: using a profile as a protective strip

Molding creates a decorative line and should not automatically absorb impacts, load, or function as a handle.

For a protective task, choose a specially designed part.

Error: covering a large construction gap

MLD-063 and MLD-064 are not intended to compensate for a serious gap or uneven wall without preparation.

Here you need a structural block, a batten, an angle bracket, or base repair. A decorative frame is a different scenario.

If the task is not related to a decorative frame, but to the cabinet body adjoining the wall, first disassemble how to close the gap between the cabinet and the wall, and only then choose a molding, batten, angle bracket, or block according to the gap width.

Who is MLD-063 suitable for

The profile is suitable for owners of small facades, nightstands, chests of drawers, drawers, and furniture with multiple frames. It is convenient next to a large handle and central decor.

MLD-063 is chosen when the line should support the composition, not become the main element.

Who MLD-063 may not suit

On a huge wall panel or a tall single door, the profile may look too thin. It is also not suitable for closing a wide construction gap.

In such cases, consider MLD-064 or another type of linear molding.

Who is MLD-064 suitable for

The profile is suitable for large cabinets, tall doors, wall panels, door leaves, and one main frame.

It is needed when the contour must be readable from a distance and work independently.

Who MLD-064 may not suit

On a small door, narrow drawer, or frequent grid, the 23 mm profile may take up too much space.

Then MLD-063 maintains a lighter and more precise composition.

When a different molding is needed

If neither 14 nor 23 mm matches the scale, it is worth opening Buy wooden moldings for furniture, walls and doors and compare other cross-sections.

The category addresses a broad request, while the article helps choose specifically between two beveled models.

Why the OMLD-005 sample set is needed

The set allows Order a molding sample before purchasing a batch. It contains 84 demonstration fragments 100 mm long.

The availability of MLD-063 and MLD-064 in the current configuration must be confirmed. The set is useful primarily for comparing material and geometry at real scale.

How to use the sample correctly

A short fragment is applied to the facade and examined in real light. But the final decision is still verified with a full-size paper frame.

The sample shows the cross-section and material, the mock-up shows the scale of the entire composition.

What to buy together

In addition to the profile, compatible materials for installation and finishing, consumables for a test sample, and tools for precise cutting will be needed.

The specific adhesive, primer, enamel, tint, or oil is chosen based on the profile material and substrate. A universal configuration without a project cannot be promised.

How to buy MLD-063

In the card, select the material, cross-section, and length: MDF 2600 mm or beech/oak 1000/2400 mm. Then calculate the frames and cutting map.

Before payment, check the current price, availability, preparation time, and the possibility of transporting long planks.

How to buy MLD-064

First, confirm that the 23 mm width is suitable for the facade or wall. Then choose MDF, beech, or oak and the required length.

For a large frame, solid long sides and the absence of a joint in the visible area are especially important.

Why it is profitable to order the entire set at once

Ordering simultaneously helps to keep material from the same batch, coordinate the finish, and avoid a shortage of long pieces.

The specification includes the profile, lengths, reserve, installation materials, and test samples.

Practical choice for a cabinet with four doors

If the doors are tall and visible from a distance, MLD-064 creates a consistent, confident rhythm. If each door is planned to have two frames or large handles, MLD-063 may be more precise.

The layout is made immediately on two adjacent doors because repetition enhances visual weight.

Practical choice for a six-drawer dresser

A large number of small fronts already creates an active rhythm. MLD-063 helps to design each drawer without the feeling of a heavy grid.

MLD-064 is only suitable for large facades where there is enough space inside the frame for the handle and free field.

Practical choice for a single wall panel

One large frame should be noticeable from the opposite side of the room. Here, MLD-064 usually works more confidently.

MLD-063 is possible if the panel has several thin fields or there is other architectural decor nearby.

Practical choice for a series of cabinets

The repeating thin MLD-063 creates a cohesive collection and does not overload each item. The same layout is transferred from the control template.

For large cabinets, you can choose MLD-064, but its visual weight needs to be assessed across the entire series.

Practical choice for doors of different heights

The same profile can look different on a low and a high door. Sometimes MLD-063 is used on small facades, MLD-064 on main high leaves.

Such a division is acceptable if the offsets and overall geometry create a clear hierarchy.

Practical choice for white enamel

On a white matte background, MLD-063 forms a thin shadow, MLD-064 a noticeable relief contour. The decision depends on the surface size and lighting.

A test coat is needed so that the bevel does not disappear or become overly active.

Practical choice for dark enamel

Dark color enhances highlights and shadows. MLD-064 may look bulkier than on a white sample, and MLD-063 more expressive.

Therefore, the profile is checked in the final color, not on a light blank.

Practical choice for natural oak

Oak MLD-063 gives a thin textured contour. MLD-064 shows more wood surface and has a stronger impact on the overall pattern.

For a series of frames, it is important to match the grain direction and shade.

How to place an order for a furniture workshop

The application specifies the article number, material, cross-section, length, number of slats, and purpose. A cutting plan and finish sample are attached separately.

This reduces the risk of replacing 14 × 9 mm with 14 × 8 mm or mixing MLD-063 and MLD-064.

How to place an order for a designer

The specification must include full card URLs, quantity, material, lengths, application location, and visualization.

Unconfirmed data regarding glue, outdoor use, or wet areas are not included as fact.

What to buy and view together with MLD-063 and MLD-064

Practical selection matrix

How to compare MLD-063 and MLD-064 in the showroom

The short fragment should be held not against the palm, but against a panel or facade of similar size. On a small sample, both profiles appear larger than in the finished frame.

First, evaluate the cross-section up close, then step back two to three meters. MLD-063 should maintain the required delicacy, while MLD-064 should not turn into an overly heavy strip.

How to check the profile under side lighting

The beveled edge reveals itself under directional lighting. The sample is rotated relative to the window or lamp to see how much the shadow emphasizes the line.

On matte enamel, the effect can be particularly noticeable. Therefore, the decision on width cannot be made only under even overhead light.

How to check the frame on an open door

The facade is considered not only when closed. When opening, the profile approaches the adjacent body, handle, and user.

It is necessary to ensure that the molding does not catch the adjacent door and does not interfere with the grip. MLD-064 is checked especially carefully on narrow modules.

How to check series repeatability

For several identical facades, one rigid marking template is used. It sets the offsets and helps avoid accumulating errors from door to door.

After the first control frame, diagonals, angles, and handle position are compared. Only then is serial cutting launched.

How to accept a finished frame after painting

Check color uniformity, bevel cleanliness, joint tightness, and absence of visible glue traces. The line should maintain a consistent width along the entire perimeter.

On MLD-064, uneven joints are more noticeable; on MLD-063, deviations from parallelism. Inspection is carried out under frontal and side lighting.

How to save data for reordering

In the archive, leave the article number, material, length, quantity, cutting map, photographs, and finishing recipe. For oak, it is useful to keep a control tinting sample.

When reordering, data is checked against the current card. It cannot be assumed that the price, availability, and material batch will remain the same.

Why a finished profile is better than a random batten

A random flat batten may have different geometry, surface quality, and depth. It will not produce the same chiaroscuro and may require additional processing.

MLD-063 and MLD-064 have a confirmed cross-section and beveled shape, making them easier to incorporate into drawings, calculations, and repeatable series.

How to choose between 1000 and 2400 mm for solid wood

The short length of 1000 mm is convenient for small facades, where one plank covers an entire side without much waste. The length of 2400 mm is better suited for tall doors, large frames, and series of elements.

The decision is made based on the cutting plan. A longer plank is not always more economical if the project consists of many short pieces, and a short one is not suitable if a seamless vertical line is important.

How to choose between 2400 and 2600 mm

The difference is not only about length but also material: 2600 mm refers to MDF, 2400 mm to beech and oak. You cannot choose a plank solely by convenient size, ignoring the finish and visual character.

For a tall painted frame, MDF can provide a seamless 2600 mm piece. For an oak tinted composition, you will have to work with a length of 2400 mm and check in advance if it is sufficient for the side.

How to make the final decision

If the 14 mm layout looks too subtle, and the 23 mm takes up too much space, do not choose at random. Open the catalog, compare adjacent cross-sections, and keep both models as references. The right molding should simultaneously support the scale of the facade, handle, finish, and viewing distance.

For a project where you need slats, corners, cornices, or baseboards nearby, it's useful to figure things out in advance, how to choose wooden moldings for interior, and then gather all items in one specification.

FAQ: Questions about MLD-063 and MLD-064

How is MLD-063 different from MLD-064?

MLD-063 has size A of 14 mm and forms a thin line. MLD-064 has size A of 23 mm and creates a more noticeable decorative contour.

How much larger is MLD-064?

Its size A is 9 mm larger, which is about 64% larger relative to size A of MLD-063.

What are the dimensions of MLD-063 made of MDF?

The confirmed cross-section is 14 × 8 mm, length is 2600 mm.

What are the dimensions of MLD-063 made of beech and oak?

Array section — 14 × 9 mm, lengths — 1000 or 2400 mm.

What are the dimensions of MLD-064?

For MDF, beech and oak, a section of 23 × 8 mm is confirmed. MDF has a length of 2600 mm, solid wood — 1000 or 2400 mm.

Which profile to choose for a small door?

MLD-063 is more often suitable: it leaves more free space and is easier to combine with a handle.

What to choose for a tall cabinet door?

MLD-064 is usually read more confidently from a distance, but the offsets and hinges need to be checked with a full-size mockup.

Which molding is suitable for dresser drawers?

For small and numerous drawers, MLD-063 is often chosen. MLD-064 is suitable for large fronts.

What to choose for a wall panel?

MLD-063 is convenient for frequent thin fields, MLD-064 for one large architectural frame.

Can both profiles be combined?

Yes, if MLD-064 creates the main outer contour and MLD-063 creates the secondary inner frame.

How to check the width before ordering?

Apply masking tape 14 and 23 mm wide to the facade and examine the composition from a normal distance.

What material to choose for enamel?

MDF and beech are more suitable for opaque painting. The choice depends on the facade base and the project task.

Which material to choose for tinting?

Oak is chosen when you need to preserve a pronounced natural texture.

What does "Prestige" sanding mean?

This is detailed surface preparation, but not a finished topcoat.

Is painting included in the product?

The cards describe profiles for subsequent finishing. The specific finish and painting service must be agreed upon separately.

How to calculate one frame?

Calculate double the sum of its width and height, then add material for corner cuts, test cuts, and a cutting map.

Can I buy exactly the net perimeter?

Not recommended. Net length does not account for layout across planks and possible errors.

What reserve is needed?

It depends on the number of frames, angles, side lengths, and the craftsman's experience. It's more reliable to build a cutting map rather than using only a percentage.

Where is the best place to place the joint?

In the least noticeable area, if a solid side cannot be achieved. Main verticals and top lines are better made from a single plank.

Which glue should I use?

Glue is chosen based on the material of the molding and the base. A universal option for MDF, solid wood, furniture, and walls cannot be guaranteed.

Can molding be installed on a door leaf?

This scenario can be considered after checking the door material, hinges, lock, and the impact of the decor on the structure.

Is MLD-063 suitable for covering a large gap?

No. This is a decorative profile, not a structural filler for a wide gap.

Why is OMLD-005 needed?

The set helps compare actual cross-sections and materials. The availability of specific MLD-063 and MLD-064 in the current composition needs to be clarified.

Where to buy MLD-063?

In the official MLD-063 card in the STAVROS wooden moldings catalog.

Where to buy MLD-064?

In the official MLD-064 card in the same catalog.

What should I check before payment?

Article number, material, cross-section, length, number of slats, cutting map, finish, mounting compound, delivery, and current availability.

Can the molding be purchased later?

Yes, but a new batch of solid wood may differ in shade and grain. It is better to order the main volume and reserve at the same time.

Do I need to paint the profile before installation?

It depends on the technology. In any case, first make a test frame and a trial paintout.

How not to confuse 14 × 8 and 14 × 9 mm?

For MLD-063, the MDF depth is 8 mm, while beech and oak are 9 mm. The material and cross-section are fixed in the specification.

Which profile is better visible from a distance?

MLD-064 is 23 mm high. MLD-063 remains more delicate and works better up close or with frequent repetition.

Result: which molding to buy — 14 or 23 mm

MLD-063 and MLD-064 solve the same problem at different scales. The thin MLD-063, 14 mm high, suits small facades, drawers, cabinets, chests of drawers, frequent frames, and furniture with a noticeable handle. The expressive MLD-064, 23 mm high, works better on a tall wardrobe door, large door leaf, and wall panel.

The material logic for the models is similar: MDF 2600 mm long for enamel, beech and oak 1000 or 2400 mm long. Beech is more often chosen for opaque painting, oak for tinting, varnish, or oil. For MLD-063, the solid wood depth is 9 mm, for MLD-064 — 8 mm for all materials.

Before ordering, you need to make a full-size mockup, check handles and hinges, calculate each side of the frame, and distribute the segments across the planks. The clean perimeter is not enough: corner cuts, test cuts, and whole long sides require a margin and a cutting map.

On the STAVROS website, you can open both cards, compare other profiles in the category, order a sample set, and select materials for installation and finishing. This approach helps you buy not just a beautiful strip, but a profile of the correct scale, material, and length for a specific facade or wall.