Bed Versailles 001-001 without mattress and slats: what to buy before delivery

If buy Versailles bed 001-001 and postpone choosing the mattress and base "for later" — on assembly day you can get a striking bed on which it's not yet possible to arrange a full sleeping area. The product card directly warns: Versailles 001-001 is supplied without a mattress and without slats for it. The mattress and support system need to be planned as separate items before the bed itself is delivered.

Versailles 001-001 has three size variants. For the external dimension 2168 × 1864 × 1509 mm, the manufacturer specifies a mattress of 2000 × 1600 mm. For the bed 2168 × 2064 × 1553 mm, a mattress of 2000 × 1800 mm is needed. For the version 2168 × 2264 × 1553 mm — a mattress of 2000 × 2000 mm. For all three variants, the card recommends a mattress thickness of at least 200 mm.

This is where the confirmed product data about the sleeping set ends. The card has no separate specification for a ready orthopedic base, no precise drawing of the internal support contour for a third-party metal frame, and no statement that any base of nominal size 1600 × 2000, 1800 × 2000, or 2000 × 2000 mm is automatically compatible with the bed. Therefore, the correct purchase is done in two stages: first, choose the size of the Versailles itself, then separately confirm the mattress and base construction specifically for the selected modification.

This is especially important for a buyer who is used to complete beds in the mass segment. There, the frame, slats, and sometimes the mattress can be sold as a pre-agreed system. In the case of Versailles 001-001, the card says the opposite: the bed is a standalone product, and the sleeping fill needs to be assembled separately.

The practical order is as follows:

1. choose one of the three bed modifications;

2. fix the corresponding mattress size;

3. choose a mattress with a thickness of at least 200 mm;

4. before purchasing the base, request from STAVROS the exact support diagram and dimensions of the internal opening, or confirm compatibility of the specific base;

5. make sure the mattress is designed for the selected type of base;

6. check the external dimensions of the bed in the bedroom;

7. measure the delivery route of the bed in a rigid plywood box;

8. synchronize the delivery times of the bed, base, and mattress.

Then on assembly day you won't have to look for a temporary solution, put the mattress on the floor, or urgently buy the first "orthopedic base" that matches the name.

Go to Catalog

Wooden bed Versailles 001-001: what's included in the order

Versailles 001-001 is a large classic bed made of beech or oak. The card shows three external dimensions and three corresponding sleeping area sizes. The item has a "made to order" status; the description separately specifies packaging in a rigid plywood box.

The key point regarding the configuration is stated by the manufacturer with utmost clarity: "Supplied without mattress and slats for it." This phrase should define the entire purchasing scenario.

Versailles 001-001 bed execution	External dimensions A × B × C	Confirmed mattress size	Recommended mattress thickness
For a sleeping area of 1600 mm	2168 × 1864 × 1509 mm	2000 × 1600 mm	from 200 mm
For a sleeping area of 1800 mm	2168 × 2064 × 1553 mm	2000 × 1800 mm	from 200 mm
For a sleeping area of 2000 mm	2168 × 2264 × 1553 mm	2000 × 2000 mm	from 200 mm

This table answers the question about the mattress but does not address the base. It is important not to substitute one size for another.

What can be considered confirmed

For the version with a width of 1864 mm, a mattress of 1600 × 2000 mm is needed.

For the version with a width of 2064 mm — 1800 × 2000 mm.

For the version with a width of 2264 mm — 2000 × 2000 mm.

It is recommended to choose a mattress with a thickness of at least 200 mm.

The bed is made of beech or oak.

The mattress and slats are not included in the delivery.

What cannot be automatically considered confirmed

You cannot write that the orthopedic base is included in the price.

You cannot promise that STAVROS will deliver the slatted frame together with the bed if it is not specified in the selected configuration.

You cannot claim that the external size of a third-party slatted base must be exactly equal to the mattress size until the actual support structure inside the bed has been checked.

You cannot independently set the number of slats, the distance between them, the height of the metal frame, or the position of the central support without technical data on the base and the bed.

You cannot buy a mattress less than 200 mm thick, expecting that the appearance will still be correct: the manufacturer's card directly recommends a thickness of at least 200 mm.

It is precisely this difference between confirmed and assumed that protects the buyer from the most expensive mistake — ordering an expensive bed and an expensive mattress, only to find that the third part of the system is not coordinated.

Why "without slats" and "without a slatted base" are not always the same thing

In everyday speech, the words "slats," "grid," and "orthopedic base" are often used interchangeably. Technically, these can be different structures.

Slats are individual planks that form the support surface under the mattress.

A slatted base is a ready-made system in which the slats are already installed in their own frame, often metal or wooden.

An integrated slat system is a variant where individual slats are installed directly onto the provided supports of the bed frame without a separate frame.

The Versailles card specifically states that the bed is supplied without slats under the mattress. It does not publish a detailed diagram from which one could determine, without measurements, which of the three options should be used by the buyer.

Therefore, when talking to a manager, you cannot limit yourself to the question "which slats should I buy?" It is better to ask specifically:

• is installation of individual slats directly into the frame provided;

• is a separate base in its own frame required;

• what should be the external dimension of this frame;

• what bed elements does it rest on;

• is a central longitudinal support provided;

• what height of the base relative to the side rails is permissible;

• does the base design affect the final mattress height.

The answer to these questions is more important than the word "orthopedic" in the product name of a third-party manufacturer.

Our factory also produces:

View Full Product Catalog

Which mattress to buy for a bed 1600, 1800 or 2000 × 2000 mm

For the mattress, the Versailles card provides a rarity for furniture products: the size is specified for each external bed finish.

Versailles 2168 × 1864 × 1509 mm: mattress 1600 × 2000 mm

This is the most compact of the three options in width. The external width of the bed is 1864 mm, the sleeping area is 1600 mm. The difference is:

1864 − 1600 = 264 mm.

If you mathematically divide this difference in half, you get 132 mm on each side. But this should not be turned into a statement about the exact thickness of the side rails: the external geometry of a classic bed can be more complex, and the dimensions take into account protruding decorative elements. The calculation is needed to understand the scale: the bed is noticeably wider than the mattress itself.

By length:

2168 − 2000 = 168 mm.

This is the total difference between the external dimensions of the bed and the length of the mattress. It is also not automatically equal to the thickness of the headboard plus footboard of 84 mm each, but it shows that you cannot plan a bedroom based solely on a 160 × 200 cm mattress.

Versailles 2168 × 2064 × 1553 mm: mattress 1800 × 2000 mm

For the popular wide double sleeping area, the external width of the bed is 2064 mm.

The difference again:

2064 − 1800 = 264 mm.

Preserved in length:

2168 − 2000 = 168 mm.

This is an important pattern in the Versailles size range: the transition from a 1600 to 1800 mm mattress increases the external width of the bed by 200 mm as well. Therefore, the relative decorative "frame" around the sleeping area remains comparable in overall dimensions.

Versailles 2168 × 2264 × 1553 mm: mattress 2000 × 2000 mm

The widest version is designed for a square mattress of 2000 × 2000 mm.

Difference in width:

2264 − 2000 = 264 mm.

By length:

2168 − 2000 = 168 mm.

The buyer gets a very wide sleeping area, but must immediately consider the external width of 2264 mm. In a room about 3 m wide, the bed itself will take up more than two-thirds of the clear wall width before nightstands and walkways.

Which of the three sizes to choose

It is convenient to make the decision not based on the principle "the bigger, the more comfortable," but on four constraints:

1. how many people sleep on the bed and what mattress width they actually need;

2. what mattress size is already selected or available from the required manufacturer;

3. how much actual space remains around the external dimensions of the bed;

4. whether not only the bed but also the mattress of the required size can be brought in.

The last point is especially easy to forget for a 2000 × 2000 mm mattress. Some mattresses are delivered rolled up, others only in full size. This is determined by the specific mattress model, not the bed. Before ordering, you need to check the packaging with the mattress seller and the delivery route separately.

Mattress thickness from 200 mm: what this recommendation means

The Versailles card recommends using a mattress with a thickness of at least 200 mm. This is the minimum guideline from the bed manufacturer, but it does not mean that any thicker mattress is automatically ideal.

Mattress thickness affects at least four things:

• the height of the sleeping surface;

• the portion of the headboard that remains visible above the mattress;

• the position of the body relative to the soft and decorative part of the headboard;

• total seating height.

If you take a mattress of 200 mm, the result will be one. If 300–350 mm, the sleeping area will rise another 100–150 mm relative to the base. Without data on the height of the specific slatted base, it is impossible to correctly calculate the final height from the floor.

Therefore, you should not choose a mattress by a single number. For a specific model, request the height of the base from the supplier, then add:

height of the base support surface + mattress thickness = height of the mattress top surface relative to the base support point.

To get the full height from the floor, you also need the actual mark of the supports inside Versailles. It is not indicated in the open card — it should be clarified from the drawing or the manufacturer.

Why you cannot compensate for an incorrect base with a very thick mattress

If the base is located lower or higher than expected, trying to "fix" the result only with mattress thickness can change the proportions of the bed. On a classic model with a high headboard, this affects the appearance, and in practice — the comfort of seating.

First, the support level must be correctly chosen, then the mattress.

The mattress and base should be purchased as a compatible pair

A size of 1600 × 2000 mm does not yet guarantee compatibility of the mattress with any slatted frame of the same nominal size. The mattress manufacturer may have requirements for the type of base.

For spring, springless, latex, or combined mattresses, the allowable gaps between supports and requirements for central support may differ. The article cannot set a universal distance between slats without the passport of a specific mattress.

Before ordering the base, provide the seller with the exact mattress model and ask the following questions:

• Does the warranty allow the use of a slatted frame?

• What is the maximum allowed distance between slats?

• Is additional central support needed for widths of 1600, 1800, or 2000 mm?

• Are there any requirements for frame rigidity?

• Is an adjustable base allowed?

• What ventilation of the mattress bottom surface is required?

After that, the technical requirements of the mattress must be matched with the geometry of the Versailles bed.

How to order a slatted base for a double bed

The main mistake here is to open a marketplace, select an "orthopedic base 160 × 200" and consider the matter closed.

A ready-made base has its own external frame size. The nominal name "160 × 200" may indicate the size of the mattress it corresponds to, while the actual external dimension of a specific product sometimes differs. The difference depends on the manufacturer.

For Versailles, you first need an answer to the question: what is the exact size of the support space inside the bed, and how should the base rest on the frame?

What to request from STAVROS before ordering the base

Ask for a technical drawing or confirmation of the following dimensions:

1. clear internal width between the bed elements in the base area;

2. clear internal length;

3. width and position of support shelves;

4. height mark of the support surface;

5. presence or need for a central longitudinal support;

6. acceptable base type — individual slats or a standalone frame;

7. restrictions on attaching a third-party base.

These parameters cannot be reliably reconstructed from external dimensions alone: 2168 × 1864, 2168 × 2064, or 2168 × 2264 mm.

What to ask the seller about the slatted base

Required:

• actual external frame dimensions, not just the size in the name;

• frame height;

• number and width of slats;

• distance between slats;

• support layout;

• permissible load;

• installation method;

• requirements for central support;

• compatible mattress sizes.

Compatibility is confirmed only at the intersection of two data sets.

Why a 1600 × 2000 mm mattress does not prove that the metal frame should be exactly 1600 × 2000 mm

The mattress must match the sleeping area, and the base frame must physically fit into the bed structure. If the finished base has an external width of exactly 1600 mm, and the internal support contour is designed for a different technical size, the result may not match.

Therefore, the rule is simple: take the mattress size from the Versailles card; confirm the size of the individual base according to the bed's technical drawing and the base's passport.

This is the main practical barrier against the error when all three products have the same numbers in their names but do not assemble into one system.

Can a solid panel be used instead of slats?

The Versailles 001-001 card does not permit replacing the slat system with a solid panel. Therefore, this option cannot be recommended as equivalent without confirmation from the bed and mattress manufacturer.

A solid panel changes the ventilation of the mattress's lower surface, the load distribution pattern, and the support structure. For a specific mattress, this may contradict the manufacturer's instructions. If a buyer considers plywood, a panel, a deck, or another homemade base only because the slats have not arrived yet, it is more correct to first obtain technical approval.

The logic of "let's put the mattress on any sheet for a couple of weeks" is especially unfortunate. A temporary solution can change the mattress's operating conditions, and a heavy solid deck can transfer load to the bed elements differently than intended by the design.

Should the base be ordered before the bed itself?

The optimal moment is after choosing the exact Versailles modification, but before the bed's delivery date.

Ordering the base too early is risky: if the buyer hasn't yet decided between a 1600, 1800, or 2000 mm mattress, the base may turn out to be the wrong size.

Ordering too late creates another problem: the bed is already assembled, but it cannot be used.

The rational sequence looks like this:

Step 1. Confirm the width of the sleeping area.

Step 2. Order Versailles 001-001 in the corresponding external size.

Step 3. Obtain or request the technical dimensions of the support contour.

Step 4. Choose the mattress.

Step 5. Obtain the base requirements from the mattress manufacturer.

Step 6. Select a base compatible with both the mattress and the bed.

Step 7. Agree on delivery dates for the three components.

If the bed is made to order, this period is convenient for selecting the sleep system. There is no need to wait for the furniture to arrive before starting to look for a mattress.

Dimensions of a solid wood bed: how much space to leave in the bedroom

The bedroom area should be calculated based on the external dimensions of the bed, not the mattress size.

For the three versions, the external length is the same — 2168 mm. The width varies: 1864, 2064, and 2264 mm.

The area of the rectangle occupied by the external dimensions can be estimated as follows:

• 2168 × 1864 mm ≈ 4.04 m²;

• 2168 × 2064 mm ≈ 4.47 m²;

• 2168 × 2264 mm ≈ 4.91 m².

This does not mean that the bed physically fills the entire rectangle as a solid mass: the furniture's shape is decorative. The calculation is needed for planning walkways and adjacent furniture.

Why you can't plan for a 160 × 200 cm mattress

If a designer drew a 1600 × 2000 mm rectangle, and then a Versailles 1600 was ordered, there will be a missing reserve of 264 mm in width and 168 mm in length.

In a small bedroom, these 26.4 cm in width can affect:

• passage to the window;

• opening the closet;

• the position of the bedside table;

• sockets;

• switches;

• curtains;

• radiator;

• the window sill protrusion.

For the 2000 × 2000 mm version, the situation is even more noticeable: the mattress seems like a 2 × 2 m square, but the actual bed has an external dimension of approximately 2.168 × 2.264 m.

Formula for checking the wall

If the bed is placed with the headboard against the wall, the minimum required width of the zone is not determined by the bed alone:

Wzone = Bbed + Pleft + Pright,

Where:

• Bbed — the external width of the selected Versailles;

• Pleft and Pright are passages or spaces for cabinets that you yourself included in the project.

For example, if for a version with a width of 2064 mm the designer leaves 700 mm of free space on each side, the total width of the composition will be:

2064 + 700 + 700 = 3464 mm.

This is an example of a design calculation, not a passage standard. You can set other values — the main thing is to calculate from the external size of the furniture.

Formula for the length of the room

By length:

Lzone = 2168 + Pfoot + Zhead,

where Pfoot is the passage you choose in front of the bed, and Zhead is the additional area behind the headboard, if it is needed at all due to a baseboard, panel, curtains, or other elements.

If the headboard is placed directly against a free wall and there are no protrusions, Z can be minimal. But a thick floor baseboard, decorative wall panel, or outlet may prevent moving the bed as it was drawn on the plan.

Headboard height 1509 or 1553 mm: what to check on the wall

The narrowest version has a height C of 1509 mm, while the two wider ones have 1553 mm.

This figure is important not only for the visual composition. Before delivery, you need to check the wall behind the bed:

• whether the sconce falls into the headboard;

• whether the switch ends up behind the furniture;

• whether the outlets are accessible;

• whether there is a wall molding that prevents pushing the bed close;

• whether the bed conflicts with the windowsill;

• whether the ventilation grille is blocked;

• whether a protruding cable duct runs along the wall.

A tall decorative headboard takes up a significant part of the wall. Moving the electrical wiring after the bed is delivered is a much more expensive scenario than checking against the drawing in advance.

If the project includes two sconces, their position should be tied to the external width of the chosen version and to the actual shape of the headboard, rather than to the center of the mattress based on a conditional rectangle.

How to check bedside tables before ordering a bed

The collection includes buy bedside table Versailles 012-001. It can be considered as a stylistically related item, but even furniture from the same collection needs to be checked against the actual room dimensions.

The wall layout becomes:

left table + gap + bed + gap + right table.

If space is insufficient, purchasing the widest Versailles 2000 may push out the bedside tables or leave inconvenient access.

Before ordering, it is useful to draw the outer outline of the bed and tables on the floor with painter's tape. Such a dry layout shows the real scale better than dimensions on the screen.

Section classical bedroom furniture should be used after the dimensions of the main bed are fixed: the large item defines the available space for the rest.

Bed 1600, 1800, or 2000 mm: comparison by actual room width

The buyer often compares only mattresses:

1600 → 1800 → 2000 mm.

For Versailles, the step of the external width is the same:

1864 → 2064 → 2264 mm.

That is, moving to the next width increases the furniture by 200 mm.

If the bedroom is already designed with almost no margin, these 200 mm can be more critical than the price difference.

Mattress	External width of the bed	How much wider than the previous version
1600 × 2000	1864 мм	—
1800 × 2000	2064 мм	+200 mm
2000 × 2000	2264 мм	+200 mm

For a couple hesitating between 1800 and 2000 mm, it is useful to do an experiment: mark both outlines on the floor and evaluate the passage for several days. This makes the choice spatial, not abstract.

What to check if the bedroom has a wardrobe with hinged doors

The bed may physically fit between the walls, but block the use of the wardrobe.

You need to mark separately:

• the outer contour of Versailles;

• cabinet depth;

• the door opening trajectory;

• the place where a person stands in front of the wardrobe.

If the wardrobe door opens toward the bed, not only the distance between the facade and the mattress is taken into account, but the distance to the most protruding part of the bed.

For the wide version of 2264 mm, an error of 10–20 cm in the plan can turn a normal wardrobe into furniture that has to be opened partially.

What to check if there is a balcony door or window nearby

The bed is 2168 mm long. If it stands sideways to the balcony door, the outer contour may fall into the door leaf or the passage.

If there is a window nearby, check:

• opening of the sash;

• access to the handle;

• curtains to the floor;

• radiator;

• convector;

• windowsill;

• possibility of cleaning.

Do not expect that the mattress ends earlier. The external frame dimension applies in the room.

Wooden double bed made of beech or oak: which material to choose

Versailles is available in beech and oak. The choice of wood species should be linked to the finish of the entire bedroom.

STAVROS describes beech as dense, non-porous wood, often chosen for items with opaque enamel. Oak has a more pronounced natural texture and is often used where it is desired to preserve it under a translucent finish.

This does not mean that beech always needs to be painted, or that oak cannot be covered with enamel. The specific bed's card allows choosing the material and color options. The practical choice is based on the desired result.

When beech is logical

Beech should be considered if:

• the bedroom is designed in light opaque enamel;

• the natural wood grain is not the main decorative effect;

• the other items in the collection are also planned in beech;

• you need to achieve the most consistent painted composition.

When oak makes sense

Oak is especially interesting if:

• the buyer values visible wood texture;

• toning is used;

• there is already oak furniture nearby;

• the wood species should be part of the visual concept.

If buy a solid wood bed together with other bedroom items, the material and finish are best fixed in one specification.

Why the bed material does not determine the material of the slats

The fact that Versailles is made of oak or beech does not mean that the slats must be of the same wood species. The base has its own engineering requirements, which are determined by the manufacturer of the base and the mattress.

You don't need to buy oak slats just for the verbal match with an oak bed.

In the closed under-mattress space, the following matters more:

• calculated load;

• elasticity;

• geometry;

• mounting method;

• compatibility with the mattress.

The material of the visible parts of the bed and the material of the technical base perform different functions.

What to check before delivering the Versailles bed

The bed is shipped in a rigid plywood box. This is one of the most important characteristics for logistics: the shipping dimensions can be significantly less convenient than the dimensions of the assembled furniture.

The product card does not publish the exact box dimensions for each version, so before delivery you need to request:

• length;

• width;

• height;

• weight;

• number of packages;

• whether the product can be unpacked before bringing it inside;

• which parts are inside;

• whether the box needs to be kept until acceptance.

Without this data, it is impossible to reliably confirm that the cargo will fit into the elevator.

Front door

Measure not the size of the door leaf, but the clear opening when the door is actually open.

Consider:

• handle;

• door closer;

• trim;

• protruding threshold;

• second door of the vestibule.

Vestibule and corridor

A large box can pass through the first door and stop at the turn.

Measure:

• length of the straight section;

• width;

• diagonal;

• possibility to place the box on its end, if allowed;

• obstacles at height.

Elevator

Required:

• width and height of doors;

• internal depth;

• internal width;

• height;

• diagonals;

• protruding handrails;

• Size of the area in front of the elevator.

Don't rely on the elevator based only on the cabin's passport dimensions. The cargo still needs to be brought through the doors at the right angle.

Staircase

If the elevator is not suitable, the route via the staircase is checked:

• width of the flight;

• size of intermediate landings;

• ceiling height;

• railings;

• turns;

• apartment entrance door on the floor.

For expensive furniture, it is useful to send the carrier photos and dimensions of difficult areas in advance.

The bed, mattress, and base may arrive via three different deliveries

Even perfectly matched sizes do not solve the synchronization issue.

The Versailles bed is made to order. The mattress may be produced by a different supplier. The base by a third.

If the base is delayed, the bed cannot be fully used. If the mattress arrives earlier, it needs to be stored somewhere according to the manufacturer's rules. If the mattress is delivered in full size, it may not fit through the same route that the disassembled frame took.

Therefore, create a simple table:

Position	Size	Supplier	Ready date	Package dimensions	Delivery date
Versailles 001-001	selected external size	STAVROS	Clarify	request	Approve
Mattress	1600/1800/2000 × 2000	mattress supplier	Clarify	request	Approve
Base	according to the confirmed outline	base supplier	Clarify	request	Approve

This small table protects better against “the bed arrived, nowhere to sleep” than trying to order everything in one day without checking deadlines.

How to accept a bed in a rigid plywood box

Upon delivery, first inspect the packaging.

If the box is damaged, take photos:

• overall view;

• damaged section;

• shipping markings;

• the point of impact or opening.

Then proceed according to the seller's and carrier's rules.

After unpacking, check the completeness against the documents. The article should not invent a list of Versailles parts that is not in the card. Therefore, the correct source is the packing list and documentation of the specific order.

The mattress and slats should not be expected as standard delivery in this list: the card directly warns about their absence.

Do I need to assemble the base before the bed arrives

If the finished base has its own frame, assembling it in advance makes sense only after confirming compatibility.

A fully assembled frame may be inconvenient to bring into the bedroom. Sometimes it is wiser to deliver it disassembled and assemble it inside the room.

But this is determined by the instructions of the specific base. You cannot disassemble a welded frame or change its design for the sake of bringing it in.

A useful question to the base seller: what is the transport size and in what form is the product delivered?

Can I temporarily put the mattress on the floor

This is already a question for the specific mattress manufacturer, not for STAVROS.

Some mattresses allow short-term use on certain surfaces, others require constant ventilation and a specific base. The universal advice "put it on the floor for a week" may contradict the instructions.

If the base is delayed, it is better to obtain a written recommendation from the mattress manufacturer in advance regarding temporary use.

Mistakes when purchasing Versailles 001-001

Mistake 1. Assuming that slats are included in the price

Reason: for many beds, the slatted base is included by default.

Consequence: on assembly day, there is no support for the mattress.

How to prevent: specify separate lines "bed", "mattress", "base" in the specification.

Mistake 2. Ordering a 1800 × 2000 mattress for the 1864 mm bed version

Reason: the buyer only remembered "large double".

Consequence: the mattress does not match the sleeping area specified by the manufacturer.

How to prevent: link each external size to a specific mattress before payment.

Mistake 3. Buying a base only by the name "160 × 200"

Reason: it seems that the nominal size matches the mattress.

Consequence: the actual frame may not match the internal support contour.

How to prevent: verify the actual external size of the base against the bed drawing.

Mistake 4. Choosing a mattress thinner than 200 mm

Reason: a suitable model is already at home or is cheaper.

Consequence: the solution does not meet the recommendation of the Versailles card.

How to prevent: choose a thickness of at least 200 mm or separately agree on an exception with the manufacturer.

Mistake 5. Planning the room based on the mattress

Reason: the furniture plan shows a standard rectangle of 160 × 200.

Consequence: 264 mm are lost in external width and 168 mm in length.

How to prevent: use the dimensions of the specific bed version.

Error 6. Not checking the rigid box

Reason: the assembled bed visually seems "collapsible and therefore will fit."

Consequence: the shipping unit does not fit into the elevator or around a corner.

How to prevent: request actual packaging dimensions before shipment.

Error 7. Mixing up the timelines of three suppliers

Reason: the bed, mattress, and base are ordered independently.

Consequence: the bedroom is not ready at the same time.

How to prevent: keep a readiness calendar for all three positions.

Mistake 8. Buying a mattress without checking the base under warranty

Reason: the dimensions matched.

Consequence: the selected slat pitch or base design does not meet the mattress manufacturer's requirements.

How to prevent: first obtain the mattress's technical requirements for the support.

Mistake 9. Buying a base that is too high and a very thick mattress

Reason: each element individually seems comfortable.

Consequence: the final sleeping surface ends up higher than expected and changes the proportions of the headboard.

How to prevent: calculate the height of the entire system before purchasing.

Mistake 10. Assuming that a 2000 × 2000 mattress is easy to bring in

Reason: the bed arrives disassembled, so the mattress will "somehow fit through."

Consequence: a full-size mattress cannot be unfolded in the stairwell.

How to prevent: request the mattress shipping packaging separately.

How to buy a solid wood bed and prepare the set right away

The correct Versailles order is better perceived not as buying a single item, but as a project of three mandatory technical layers and one interior layer.

Layer 1. Bed

It is necessary to record:

• article Versailles 001-001;

• external size;

• material — beech or oak;

• selected finish;

• completion time;

• number of shipping units;

• dimensions of the rigid box.

Layer 2. Mattress

The specification specifies:

• length 2000 mm;

• width 1600, 1800, or 2000 mm;

• thickness of at least 200 mm;

• exact model;

• manufacturer's requirements for the base;

• transport dimensions;

• delivery method — full-size or rolled, if permitted by the model.

Layer 3. Base

Need to know:

• structural type;

• actual external dimensions;

• height;

• support layout;

• distance between slats;

• design load;

• requirements for central support;

• compatibility with the selected mattress;

• compatibility with the internal geometry of Versailles.

Layer 4. Bedroom

Before placing an order, they check:

• wall width;

• room length;

• wardrobe;

• doors;

• nightstands;

• wall sconce;

• sockets;

• curtains;

• delivery route.

This approach is especially useful when the buyer wants classic solid wood beds and compares several models at once: you need to choose not only by appearance, but also by how well the entire bedroom set fits together in a specific room.

Set for the 1600 × 2000 mm version: practical scenario

Suppose Versailles with external dimensions of 2168 × 1864 × 1509 mm is selected.

Confirmed mattress — 1600 ×

Kit for the 2000 × 2000 mm version: what changes besides the mattress width

The 2168 × 2264 × 1553 mm version is designed for a 2000 × 2000 mm mattress.

When purchasing a square two-meter mattress, several tasks change at once.

Mattress delivery

If it cannot be rolled up, the packaging can be very large. A staircase and elevator sufficient for a disassembled bed may not necessarily accommodate the mattress.

Base

The wider the sleeping area, the more important it is to obtain a confirmed support scheme. You cannot assume that a 2000 mm wide base is arranged the same as a 1600 mm one, just with longer slats.

Bedding

The size of the fitted sheet, mattress pad, and protective cover should be chosen based on the actual 2000 × 2000 mm mattress and its thickness. This is no longer a product characteristic of Versailles, but a practical part of bedroom preparation: a standard set from the previous bed may not fit.

Mattress rotation

If the mattress manufacturer's instructions require periodically changing its orientation, the physical space around the bed must allow this to be done safely. For a heavy square mattress of two-meter width, this is a separate household operation.

How to calculate space for two bedside tables

Suppose the buyer wants a symmetrical composition: the bed in the center and one table on each side.

Formula:

Wwall = Bbed + 2 × Btable + 2 × Z,

where Z is the selected gap between the bed and the table or between the table and adjacent elements, depending on the layout.

If the table has a width of 685 mm, like Versailles 012-001, two tables give:

685 × 2 = 1370 mm.

Then just the bed of the 1600 version plus two tables take up:

1864 + 1370 = 3234 mm

without any additional gaps.

For version 1800:

2064 + 1370 = 3434 mm.

For version 2000:

2264 + 1370 = 3634 mm.

These numbers dramatically change the perception of sizes. A person may think that a 160 cm mattress easily fits on a 3.3 m wall, but the composition with a pair of large classic nightstands already takes up almost the entire width.

In such a case, you can:

• abandon the symmetrical pair;

• choose a different nightstand;

• shift the bed;

• choose a smaller width of Versailles;

• Rework the entire bedroom wall.

This cannot be resolved after delivery without compromise.

How to check outlets and sconces before installing Versailles

Electrical work must function after the furniture has taken its place.

For each outlet on the wall behind the bed, measure the distance:

• from the floor;

• from the center of the wall;

• from the nearest corner.

Then transfer the outer contour of the headboard to the drawing.

If the outlet ends up completely behind the tall headboard, access to it may disappear.

If the sconce is mounted too low, the decorative part of the bed may block it.

If the sconce is too close to the side edge, when changing the version from 1600 to 1800 or 2000 mm, the bed may hit the light fixture.

Therefore, it is better to tie the electrical work to the specific external size of Versailles rather than to the conditional center of the future mattress.

How to prepare the floor and baseboard

Before assembling an expensive wooden bed, make sure the finished floor is complete, clean, and protected during installation.

A tall protruding baseboard can push the headboard away from the wall. If the designer calculated the exact position of the bed, this will change the length of the walkway in front of the footboard.

A floor outlet, access panel, convector, or floor covering transition should also be marked on the plan.

Do not cut the baseboard in advance for the bed without a drawing and approval: the external dimension does not show the exact shape of the furniture's contact with the wall.

What to do if the mattress was already purchased before choosing Versailles

This is a common reverse scenario.

Already have a mattress 1600 × 2000 mm

Consider version 2168 × 1864 × 1509 mm, but additionally check:

• mattress thickness — from 200 mm per bed recommendation;

• mattress requirements for the base;

• condition and service life of the mattress;

• possibility of use with the new support system.

Already have a mattress 1800 × 2000 mm

Need version 2168 × 2064 × 1553 mm.

Already have a mattress 2000 × 2000 mm

Need version 2168 × 2264 × 1553 mm.

If the size of the existing mattress differs, you cannot select the "closest" Versailles and hope for gaps. The card links three specific sizes.

What to do if you already have a slatted base

Here, even a nominal match is not enough.

Take the actual dimensions from the base:

• outer width;

• outer length;

• height;

• position of legs or supports;

• frame thickness;

• protruding fasteners.

Take a photo of the structure and send the data to the STAVROS manager for verification against the internal geometry of the selected bed.

If compatibility is not confirmed, it is better not to consider the base as part of the new project.

This is especially relevant for bases on their own legs: they can transfer the load directly to the floor and require only geometric placement inside the bed, or they can structurally conflict with the internal elements of the frame. Without a drawing, a conclusion is impossible.

When it's better to postpone buying a Versailles

You shouldn't order a bed just because you liked the model if the basic constraints haven't been resolved yet.

Non-standard mattress size

If you need a mattress of 1700 × 2000, 1900 × 2000, 2000 × 2200, or another non-standard size, the product card does not confirm a corresponding standard modification of the Versailles.

The room has been measured only approximately

For a dimension over two meters, even an error of 50–100 mm can affect the passage and neighboring furniture.

The base has already been purchased in principle

If an expensive adjustable or motorized base cannot be replaced, you first need to confirm its physical compatibility.

The route of the rigid box has not been checked

If the only path goes through a small elevator and a narrow turn, logistics need to be resolved before production.

The electrical work is still being designed

First, it's useful to tie sconces and outlets to the exact bed size to avoid redoing the wall.

The buyer expects a set of "bed + mattress + slats"

This is not a confirmed configuration. If a ready-made unified set from one seller is needed, it should be clarified in advance whether it can be formed as a separate order; one cannot rely on the Versailles card as such a configuration.

How to allocate a budget without fixing rapidly changing prices

The bed price depends on size, material, and finish and may change. The price of the mattress and base is generally set by other suppliers if purchased separately.

Therefore, in the article it's more useful not to fix specific amounts, but to create a budget structure:

Final bedroom budget = bed + mattress + base + bed delivery + mattress delivery + base delivery + lifting/carrying in, if paid separately + assembly, if purchased separately + textiles.

Before payment, fill in each line with a real figure.

So an expensive mattress or complicated delivery won't appear unexpectedly after you've already paid a deposit for the furniture.

How to synchronize warranty requirements for three products

The bed, mattress, and base may have different warranty terms.

For the bed, proper assembly and use are important.

For the mattress, the manufacturer may require a specific type of base.

The base has its own permissible load and installation scheme.

Therefore, keep:

• the order for Versailles;

• the drawing or confirmation of internal geometry;

• the base passport;

• mattress passport;

• correspondence about compatibility, if any.

If a question about operation arises later, it will be clear what data the set was assembled from.

How to check the height of the finished sleeping area before delivery

The buyer can estimate the future height in advance only after obtaining three values:

1. the support mark inside the bed from the floor;

2. the height of the slatted base above this support;

3. the thickness of the mattress.

Formula:

H_sleeping area = H_support + H_base + H_mattress.

The Versailles card confirms only the third part as a recommendation: a mattress from 200 mm. The open card does not publish the exact H_support.

Therefore, there is no need to invent a final height based on photographs. Request the drawing.

If a person wants a specific seating position — for example, due to height, knee condition, or habit — this is especially important.

Is it necessary to leave a ventilation gap under the mattress

Specific requirements are set by the manufacturer of the mattress and the base.

The very presence of slats is usually associated with ventilation and support, but the article should not establish a universal area of open space.

If the mattress has a warranty requirement for ventilation, pass it on to the base seller.

If a closed box or storage of things under the bed is planned, it is necessary to separately check whether this worsens the operating conditions of the selected mattress.

How to understand that the base is too high

There are two types of risk.

Geometric: the base physically protrudes above the intended level of the side rails.

Visual: the mattress rises so high that the proportions of the headboard change.

Before purchasing, ask the seller for the exact frame height of the base. Then compare it with the bed's drawing.

Don't expect that "everything will hide under the mattress." The height of the base affects the entire package.

How to understand that the base is too low

If the standalone frame is placed on its own legs and is lower than expected, the mattress may sit deeper inside the frame. This can change seating comfort and access to the mattress edges.

But without the internal drawing of Versailles, it's impossible to specify an allowable range.

The precise check again comes down to one document — the diagram of the internal support contour.

Buyer's checklist a week before delivery

A few days before the bed arrives, check:

• the exact version of Versailles matches the one ordered;

• the mattress is selected of the correct size;

• the mattress thickness is not less than 200 mm;

• the base is confirmed by the actual external dimension;

• the mattress requirements for slats are met;

• the base physically fits into the bed;

• all three deliveries are confirmed;

• the dimensions of the rigid plywood box are known;

• the delivery route is cleared;

• the elevator is checked;

• dirty work in the bedroom is completed;

• sockets and sconces do not conflict with the headboard;

• nightstands fit;

• space is prepared for temporary storage of the mattress or base, if timelines diverge.

This is a case where fifteen minutes of checking saves several days of inconvenience.

Buyer's checklist on assembly day

Before installing the mattress:

1. check the bed against the order;

2. verify the external dimensions;

3. inspect the finish;

4. confirm the internal geometry of the base;

5. install the base according to its instructions;

6. make sure it rests as intended by the design;

7. only after that place the mattress;

8. check that the mattress lies flat and does not jam in the frame;

9. do not use random spacers or homemade supports to compensate for misalignment.

If the base does not match, it is better to stop the assembly and clarify the solution than to "modify on site" expensive furniture without approval.

Final specification before placing the order

Before ordering a solid wood bed, it is useful to consolidate all parameters on one sheet.

Position	What must be confirmed
Versailles 001-001	exact external size
Material	Beech or oak
Finishing	Selected option from current card
Mattress	1600 × 2000, 1800 × 2000, or 2000 × 2000 mm
Mattress thickness	from 200 mm
Base	actual external dimensions and construction
Slats	mattress requirements and base scheme
Base height	to calculate the final sleep height
Room	bed outer contour plus walkways and furniture
Bed packaging	dimensions of the rigid plywood box
Mattress packaging	request from its seller
Delivery	coordinate the timing of three items

If at least one technical line contains "approximately," "probably," or "should fit," the order is not yet fully prepared.

Bottom line: the bed should be chosen together with the bedding set, even if it is sold separately.

Versailles 001-001 is not a ready-made set of "frame + mattress + orthopedic base." The product card directly states that the mattress and slats are not included in the delivery. Therefore, a sensible purchase begins not with an attempt to add the bed to the interior, but with a precise specification.

For the 2168 × 1864 × 1509 mm version, a 1600 × 2000 mm mattress is needed in advance. For 2168 × 2064 × 1553 mm — 1800 × 2000 mm. For 2168 × 2264 × 1553 mm — 2000 × 2000 mm. In all cases, the manufacturer recommends a mattress thickness of at least 200 mm.

But the base size cannot be reliably derived only from the mattress size. Before purchasing it, you need to obtain the internal geometry of the bed, the actual dimensions of the base, and the mattress manufacturer's requirements for support. This is the most important check of the entire configuration.

Next, the room is calculated. The external dimension of each Versailles is 264 mm wider than the mattress and 168 mm longer. If the bedroom was drawn only based on the rectangle of the sleeping area, the plan needs to be recalculated.

After that, bedside tables, wall lamps, sockets, wardrobes, and the delivery route are checked. The bed is packed in a rigid plywood box, so the transport dimension should be requested separately.

When these points are covered, you can arrange the bed, mattress, and base so that their readiness falls within the same period. If the purchase is made through STAVROS, before final delivery coordination, check the current payment and delivery terms for the bed.

Then the decision to buy a wooden bed turns into a truly prepared purchase: on assembly day, there is not only a beautiful solid wood frame, but also compatible mattress and base, free space in the bedroom, and a verified delivery route. The main thing is not to perceive the missing slats as a minor component that can always be picked up later. For Versailles 001-001, this is part of the sleeping area project that needs to be decided in advance.

Frequently asked questions about the Versailles 001-001 bed, mattress, and slatted base

Is the mattress included in the price of Versailles 001-001?

No. The product card clearly states that the bed is supplied without a mattress and slats for it. Therefore, the mattress should be considered a separate purchase and not included in the expected standard configuration.

Are slats supplied with the bed?

No, according to the current description, slats are not included in the delivery. Before ordering, you need to clarify which specific base construction should be used with the selected modification: individual slats or a standalone slatted base. The open product card does not provide sufficient internal geometry to choose a third-party base based only on the external dimensions of the bed.

What thickness should the mattress be?

STAVROS recommends a mattress thickness of at least 200 mm. The maximum allowable or optimal thickness is not specified in the product card. Therefore, for a very tall mattress, you need to additionally calculate the total height of the sleeping area and check the proportions of the headboard.

How do the bed dimensions relate to the sleeping area?

The Versailles 2168 × 1864 × 1509 mm is designed for a 1600 × 2000 mm mattress. The version 2168 × 2064 × 1553 mm is for a 1800 × 2000 mm mattress. The version 2168 × 2264 × 1553 mm is for a 2000 × 2000 mm mattress.

In all three cases, the external width is 264 mm greater than the mattress width, and the external length is 168 mm greater than the mattress length.

Can I order an oak bed?

Yes. The product card shows two materials — beech and oak. Before ordering, you also need to choose the size and finish option. If the bedroom is furnished with several items from the same collection, it is better to agree on the wood type and finish for the entire set at once.

Can I order a beech bed with white enamel finish?

The product card shows the beech version and white enamel RAL 9010 among available options. The current combination, lead times, and price need to be checked directly in the product card or with a manager before placing an order.

Can I buy a 1600 × 2000 mm mattress in advance?

Yes, if the Versailles modification 2168 × 1864 × 1509 mm has been finally selected and the mattress meets the recommended thickness of at least 200 mm. However, before use, you also need to ensure a compatible base.

Can I order the base before the bed?

Yes, after confirming the exact bed modification and its internal support geometry. Buying a third-party base based only on the nominal phrase "160 × 200", "180 × 200", or "200 × 200" is risky.

What should be the external size of the slatted base for a 1800 × 2000 mm mattress?

The open product card for Versailles does not publish this parameter. The nominal mattress size should not be automatically taken as the exact external dimension of the base frame. You need the bed drawing and the actual size of the selected base.

Is a separate base needed for the 2000 × 2000 mm version?

The product card confirms the absence of slats but does not describe a specific third-party base structure. Therefore, the method of supporting the 2000 × 2000 mm mattress must be agreed upon before purchase. For such a wide sleeping area, it is especially important to check central support and the mattress manufacturer's requirements.

Can I use an old base from another bed?

Only after checking its actual size, height, support layout, and compatibility with Versailles. Matching the size of the old mattress alone is not sufficient.

How to prepare the room for delivery of a large bed?

You need to check the outer contour of the selected version, headboard height, wardrobes, doors, nightstands, outlets, and sconces. Separately request the dimensions of the rigid plywood box and check the entrance, vestibule, elevator, stair landings, and turns.

Do I need to measure the elevator if the bed is disassembled?

Yes. The card indicates a rigid plywood box, and its actual dimensions are not automatically equal to the dimensions of one part of the disassembled bed. Without the shipping dimensions, passage through the elevator cannot be confirmed.

What should be ordered first — the bed or the mattress?

First, you need to finally choose the Versailles modification. After that, the mattress can be ordered in parallel with the bed production if its size and thickness are already confirmed. The base is ordered after checking the bed geometry and mattress requirements.

Can I choose a mattress with a thickness of 180 mm?

This is below the card's recommendation of "from 200 mm." Without separate approval from the bed manufacturer, this option cannot be described as meeting the stated recommendation.

If the mattress is 250 mm, does it fit?

It meets the lower limit of the recommendation "from 200 mm", but this does not yet confirm overall compatibility. The final height of the sleeping area must be calculated together with the base. A very thick mattress can change the visual proportions of the bed.

Why can't you just put the mattress on slats of suitable width?

Because you need to consider not only the width of the mattress, but also the method of attaching the slats, the support contour, central support, the allowable gap between slats, and the mattress warranty requirements.

Is a central beam needed under a mattress of 1800 or 2000 mm?

The open Versailles card does not provide a technical answer to this question. The presence of central support should be determined by the design of the bed and the chosen base. You should not invent it yourself based on a general rule.

What to do if the base arrived earlier and does not fit into the bed?

Do not cut or modify the frame without the manufacturer's permission. First, compare the actual dimensions with the agreed specification and contact the supplier of the base or bed.

Can I buy the bed now and choose the base after assembly?

Technically, yes, but then after delivery you will be left without a ready sleeping area. The central goal of this article is precisely to have the base confirmed before the bed arrives.

Will Versailles fit in a small bedroom?

What matters is not the conventional word "small," but the dimensions. The most compact version has an external footprint of 2168 × 1864 mm, meaning it occupies a rectangle of about 4.04 m² before accounting for walkways and other furniture. Mark the layout on the floor and check the actual remaining areas.