For a boutique, three identical tables with a height of 790 mm are being assembled: how to order 12 modern furniture legs MN-238 if only 11 beech ones are available

Three identical tables should appear in the boutique's sales floor: two are intended for displaying collections, the third for wrapping purchases and consultant work. The designer has already approved a height of 790 mm, tabletops 40 mm thick, and an open underframe without an apron that would hide the supports. Therefore, the legs become not a technical detail, but a noticeable part of the composition.
The project includes a modern furniture leg MN-238 with a height of 750 mm. The 40-millimeter tabletop brings the item to the required mark: 750 + 40 = 790 mm. For three tables, 12 identical supports are needed. However, at the time of checking the card in St. Petersburg, a stock of 11 beech items was published. This is a typical situation where the decision cannot be made by clicking the "in stock" button. The buyer needs to coordinate the full batch, material, production time for the missing item, and a uniform finishing result.

Modern Furniture Leg MN-238

from 107.84 $

Go to Catalog

Modern furniture leg MN-238: what the product card confirms

MN-238 is not a universal blank of arbitrary length. The card specifies a specific dimension of 750 × 109 × 88 × 34 mm. The designation reflects the height and main cross-sections of the complex profile. The part has a pronounced central spherical section and transitions to narrower areas. It is this geometry that makes the support noticeable even under a large tabletop.
Beech and oak are available for order. The sanding quality "Prestige" is specified: the product is prepared for subsequent finishing, but the final color and protective coating are arranged by the buyer as part of their furniture production. The basic configuration of the card is shown under enamel.
As of August 31, 2026, the price of a beech MN-238 was 8,840 RUB, and an oak one — 12,830 RUB. In Saint Petersburg, 11 beech and 6 oak legs were listed, in Moscow — one beech. Stock levels change, so these figures serve as a calculated snapshot, not a promise of availability on the date of reading the article.
To place an order for a specific product, you need to buy the modern furniture leg MN-238 through the active product card after re-checking the variant, price, and shipping city.

Watch video ...

Wooden table support 750 mm high: how the 790 mm mark is obtained

The calculation seems simple: to a leg 750 mm high, a tabletop 40 mm thick is added. The result is 790 mm. But this arithmetic is only correct if there are no elements that change the height.
Before ordering, the designer checks:

• the actual thickness of the tabletop after calibration and finishing;

• the presence of shims between the leg and the tabletop;

• the thickness of the mounting plate;

• the presence of an adjustable support or foot underneath;

• the need to compensate for floor unevenness;

• the method of connection without recessing the leg into the tabletop;

• the allowable height of the finished item according to the design project.

If a 5 mm foot pad is added underneath and a 3 mm mounting plate on top, the height will become 798 mm instead of 790 mm. If the tabletop has a stated 40 mm only along the thickened edge, while the actual body of the slab is thinner, the calculation will also change. Therefore, the purchaser provides the furniture manufacturer with a drawing of the assembly, not just the sum of two dimensions.
The height of tables in one room must be controlled from the finished floor. Local base level differences cannot be corrected by sawing off one wooden leg: the manufacturer states that cutting to size is not performed, and unauthorized shortening changes the geometry, support area, and appearance of the set.

Our factory also produces:

Table STL-016

from 880.28 $

STL-017 Table

from 964.58 $

Baseboard for Table STL-026-2

from 454.66 $

Table base for STL-026-3

from 361.94 $

Baseboard for Table STL-026-5

from 463.44 $

Baseboard for Coffee Table STL-026-8

from 288.26 $

Pedestal for Table STL-027

from 2,628.40 $

Table Svamp 002-013

from 911.39 $

View Full Product Catalog

How many modern furniture legs to order for three tables

Each freestanding table is provided with four legs. Batch calculation:
3 tables × 4 legs = 12 legs.
This is not a case where eleven parts can be distributed among three items. The 4 + 4 + 3 scheme does not create a third finished table. The customer needs either a full batch of twelve MN-238 units, or a revision of the entire design of the third item before placing the order.
Ordering one spare leg automatically is also not mandatory. The spare would increase the batch to 13 items and the budget, but would not eliminate the risk of wood and finish differences if the spare part is stored without labeling. The decision is made based on operating conditions. For a boutique with frequent rearrangements, a spare may be reasonable; for stationary furniture with model availability, it is enough to keep the article number, drawing, color sample, and specification.
If a different type of support is needed or you need to evaluate the assortment before fixing the article number, you can Buy wooden furniture legs in the relevant section. But after approving MN-238, you cannot unnoticedly replace one of the twelve parts with a similar model: the difference will show in the spheres, cross-sections, and light and shadow.

Beech furniture legs: what to do if 11 pieces are indicated in Saint Petersburg

The published stock of 11 pieces is one item short of the project's requirement. Three working options are possible, but each requires seller confirmation.
The first is to reserve 11 items in Saint Petersburg and wait for the production of one missing leg. In this case, it is agreed in advance whether it is acceptable to combine a warehouse part and new production in one finishing batch. For opaque enamel, the natural difference in wood is usually less noticeable, but the geometry, sanding, and preparation must still be identical.
The second is to clarify the possibility of moving one beech MN-238 from Moscow. The card indicates one unit in Moscow, but availability in two cities does not mean automatic merging of stock, the same production date, or free transfer. Before payment, confirmed timelines and delivery scheme are needed.
The third option is to order all 12 items as a single production batch. This option may increase the wait time, but it simplifies assembly and acceptance. It is especially logical if the finish will be transparent or semi-transparent and the designer needs a consistent wood grain layout.
You cannot order 11 pieces now and leave the question of the twelfth for "later" if the installation date is already fixed. One unfinished table can delay the opening of the entire area. A commercially correct order is twelve confirmed items with a clear completion date, not the maximum quantity available for immediate addition to the cart.

Oak furniture leg MN-238: is it worth changing the material for the sake of availability

The oak legs card has fewer: six pieces in Saint Petersburg. Therefore, switching from beech to oak does not solve the shortage of a finished batch. For twelve supports, production or additional transfer will still be required.
The material is chosen based on the finish and the artistic task. Beech has a calmer structure and is often used under opaque enamel. Oak has a pronounced texture that makes sense to preserve under a transparent or tinted coating. Buying six beech and six oak legs just to use the warehouse is risky: under a transparent finish, the difference will be obvious, and under enamel, the customer pays for oak without the need to showcase its grain.
Within a single set, all three tables should be specified in one wood species. Mixing is only possible as a deliberate design choice: for example, different materials for tables serve a navigation function. In our project, the tables should look identical, so such logic is absent.
Before choosing, it is useful check the quality of wooden supports and coordinate the finish system with the painting workshop. The wood species name does not replace a test stain.

Price of twelve wooden legs MN-238

According to the prices published on 31.08.2026, the beech batch is calculated as follows:
12 × 8,840 RUB = 106,080 RUB
Oak batch:
12 × 12,830 RUB = 153,960 RUB
The difference:
153,960 − 106,080 = 47,880 RUB
This is the cost of the items themselves. The full budget includes delivery, packaging, mounting hardware, floor glides, trial finishing, primer, enamel or tinting system, painter's work, assembly, and installation. If one missing leg is shipped separately, an additional transport leg arises. Therefore, the option "take eleven at once" is not necessarily cheaper than a single order.
The price must also be re-confirmed before payment. The balance may change, and the card reflects the current retail configuration. In the estimate, it is advisable to separate the goods and subsequent work so that the buyer can see what causes the final amount to change.

Unpainted furniture legs: one finishing batch for three tables

When the supports are exposed to view, the slightest difference in white or colored enamel between the tables becomes noticeable. Therefore, all 12 pieces are handed over to a single contractor and painted according to a unified process card. If one leg arrives later, the composition, color code, material batch number, gloss level, and application mode are preserved for it.
Before painting, the products are laid out on tables: C1-1…C1-4, C2-1…C2-4, C3-1…C3-4. The marking is placed where it will not damage the front surface. After geometry control, a test coating is performed on an agreed wood sample or on a technologically acceptable area.
The customer must determine what "same color" means. Matching only an electronic image is not enough: the screen does not convey texture, coverage, or gloss. The reference becomes a physical sample approved under boutique lighting.
If the project has not yet fixed a specific model, you can order unpainted furniture legs from the corresponding subsection. In our case, MN-238 is already selected, so the task is not to expand the assortment, but to precisely replicate the finish.

Geometric furniture support MN-238 and tabletop construction

A beautiful profile does not confirm the load-bearing capacity of the finished table. The card provides dimensions and material, but the designer separately calculates the joint, tabletop, stability, and operational loads. Unverified figures from promotional descriptions cannot be transferred into working documentation.
The upper zone of the leg must have sufficient contact area with the supporting frame or tabletop. Fasteners cannot be selected only by length: consider the grain direction, part thickness, edge distance, forces during rocking, and serviceability. Three tables for a sales floor may experience not only vertical load from merchandise, but also horizontal impact during movement and accidental leaning by a visitor.
If the tabletop is long, four legs may not be enough without a stretcher or metal reinforcement. This is not a drawback of MN-238, but a matter of the entire structure. Before purchase, the following are approved:

• length, width, thickness, and material of the tabletop;

• location of the four support points;

• distance of legs from edges;

• presence of a frame or embedded elements;

• deflection calculation;

• mounting unit;

• floor protection;

• possibility of bringing in the assembled table.

For a preliminary preview of profile options, you can choosing wooden table legs, but the technical decision is made by the furniture designer.

Conical wooden leg and passages in the sales area

MN-238 has a variable cross-section and a central volumetric element. On the plan, it cannot be depicted with a single thin centerline. The buyer needs front and side contours, especially if the tables are placed near narrow passages, fitting rooms, or display windows.
The minimum passage is measured between the actual protruding parts of the furniture, not between the edges of the tabletops. If the legs are extended outward or tilted by the table design, the lower zone may be closer to the visitor's path. At the same time, too large an inward offset creates an overhanging edge that is easy to catch on.
Before ordering, it is useful to print the MN-238 outline at 1:1 scale and apply it to the tabletop corner mockup. Even more reliable is to assemble one full-size fragment of the unit. This allows checking whether a sphere with a diameter around the specified cross-section conflicts with the display case base, baseboard, or product layout.

Modern leg MN-238 and alternative MN-237

MN-237 may look close in style, so a buyer could mistake it for a replacement for the missing twelfth position. This cannot be done without a new drawing and visual approval. Even a related model has different geometry and forms a different silhouette.
The link to the alternative is needed not for a mixed purchase, but for meaningful comparison before approving the specification. You can compare the modern furniture leg MN-237, after which choose one model for all twelve positions.
If MN-237 better matches the tabletop depth or visual concept, the entire set is changed, not just one leg. A combination of 11 MN-238 + 1 MN-237 looks like a configuration error, even if the height matches.

How to order 12 wooden supports MN-238: step-by-step specification

Step 1. Fix the structure of three tables

Approve the countertop dimensions, thickness of 40 mm, final height of 790 mm, leg placement, and presence of a reinforcing frame.

Step 2. Specify the full article number and quantity

In the request, write: MN-238, 750 × 109 × 88 × 34 mm, 12 pieces. You cannot limit yourself to the phrase "twelve modern legs."

Step 3. Choose one wood species

For opaque enamel, consider beech; to showcase the texture, use oak. Confirm the decision with a color sample and estimate.

Step 4. Clarify the unified configuration of the batch

Ask how the twelve items will be assembled given the published stock of 11 beech or 6 oak: relocation, additional production, or a new batch.

Step 5. Confirm the deadline

The average production time for a missing item is stated as 5–10 working days. Add finishing, delivery, and installation to this.

Step 6. Coordinate the finish

Hand over all details to the painter at once or secure the technology for the later item. Approve a physical sample of color and gloss.

Step 7. Develop the mounting node

The designer determines embedded parts, fasteners, frame, and foot pads. The product card does not replace the calculation for the finished table.

Step 8. Coordinate logistics

Before payment, you should check the payment and delivery terms for furniture supports, especially if the items are located or produced in different cities.

What to check upon receiving twelve MN-238

The delivery is accepted before painting and assembly. First, verify the documents, then sort the items into three groups of four pieces each.
Check:

1. article MN-238 on all items;

2. quantity — exactly 12 pieces;

3. published size 750 × 109 × 88 × 34 mm;

4. one selected wood species;

5. "Prestige" quality;

6. integrity of the spherical part and narrow sections;

7. absence of transport damage;

8. conformity of ends and mounting zones to the drawing;

9. ability to sort wood across three tables;

10. marking of packages;

11. absence of unauthorized cutting;

12. conformity to the reference sample after trial finishing.

Tolerances and acceptance criteria are agreed upon before purchase. Any natural variation in the wood grain pattern cannot be declared a defect, but a noticeable geometric issue cannot be accepted either, citing the naturalness of the material.

Mistakes when buying modern furniture legs

1. Order 11 legs for three four-legged tables.

2. Count the remnants of Moscow and Saint Petersburg as one collected batch.

3. Buy six beech and six oak items for the sake of availability.

4. Do not re-check the price before payment.

5. Add only the decorative edge thickness of the tabletop to 750 mm.

6. Forget about the mounting plate and the foot.

7. File down one leg to compensate for the floor.

8. Order the missing item after painting the rest.

9. Mix MN-238 and MN-237.

10. Choose fasteners without a designer.

11. Do not check the deflection of the long tabletop.

12. Paint three sets on different days without a reference.

13. Count the price of legs as the full cost of tables.

14. Leave no time for production and finishing.

15. Accept goods after handing them over to the painter.

Additional technical recommendations can be obtained on the page where you can study tips on finishing and installing furniture legs. Any advice relates to a specific design and coating system.

When it is worth buying the furniture leg MN-238

MN-238 suits the project if an open modern support with a height of 750 mm is needed; the tabletop and mounting assembly bring the furniture to the required level; the spherical geometry supports the concept; all 12 items are ordered in the same wood species and quality; the designer confirmed stability; the finisher is ready to provide a uniform finish; the delivery time is agreed before installation begins.
For a boutique, the model is especially appropriate when tables should look like a family but remain visually lighter than closed cabinets. Repeating one leg on three items ties the sales floor together better than a random set of similar supports.

When it is premature to buy the wooden support MN-238

The purchase should be postponed if the tabletop height is still changing; its actual thickness is unknown; the frame is not developed; a leg needs to be trimmed; the project requires a hidden adjustable support with a large range; passages are not checked; the buyer expects to receive twelve pieces immediately based only on the general status "in stock"; the material and finish are not agreed upon.
Also, MN-238 should not be purchased as a universal replacement for any table support. The specific geometry must be part of the project. If the sphere seems overly decorative or the cross-sections conflict with a thin tabletop, it is better to change the model before ordering the entire batch.

Modern furniture legs MN-238 for three tables: summary

For three tables on four supports, 12 identical MN-238 are required. A leg with a height of 750 mm together with a 40 mm tabletop gives a calculated 790 mm, if the assembly does not contain additional elements. According to prices as of 31.08.2026, a set of beech costs 106,080 RUB, of oak — 153,960 RUB.
The published stock in Saint Petersburg is insufficient: 11 beech items and 6 oak items. This is not a reason to mix wood species or models. Before payment, the seller must confirm how the full batch will be assembled, when the missing part will be ready, and whether a single shipment is possible.
A commercially competent order contains the article number, full dimensions, 12 pieces, one wood species, "Prestige" quality, purpose for the selected finish, delivery city, and required date. It is accompanied by a drawing of the assembly, a marking map for three sets, and a physical finish sample. Then the three tables truly look identical, and one leg missing from the warehouse does not become a problem on the eve of the boutique opening.

Frequently asked questions about the modern furniture leg MN-238

What is the height of MN-238?

The card indicates a height of 750 mm.

What is the full published size?

750 × 109 × 88 × 34 mm.

How many legs are needed for three tables?

With four supports, each table requires 12 pieces.

How to get a table height of 790 mm?

In the basic calculation, a 40 mm tabletop is added to the 750 mm leg. Plates and floor glides are accounted for separately.

What wood is MN-238 made from?

The card suggests beech and oak.

What sanding quality is available?

"Prestige".

How many beech legs were in stock?

As of 31.08.2026, the card showed 11 pieces in Saint Petersburg and one in Moscow. Before purchasing, stock levels are re-checked.

Can the stock from two cities be combined?

Only after the seller confirms the transfer, timing, and delivery conditions.

Can I buy 11 MN-238 and one MN-237?

You should not: these are different models. Replacement requires reviewing the entire set.

Can the manufacturer shorten the leg?

The card states that cutting and trimming to size are not performed.

How much does a set of beech cost?

At a price of 8,840 RUB per piece, twelve items cost 106,080 RUB. The price is valid only on the date of verification.

How much does the oak set cost?

At a price of 12,830 RUB per piece — 153,960 RUB.

Does painting include in this calculation?

No. Finishing, fasteners, delivery, and installation are calculated separately.

Do I need to order a spare leg?

Not automatically. The decision depends on operation, model availability timelines, and budget.

Where to order wooden table legs?

The specific MN-238 is ordered through the product card, while other options are selected in the wooden furniture legs section.