The two cabinet doors are ready: which wooden molding MLD-024 to buy — beech under enamel or oak under tinting

If two tall cabinet doors are already manufactured, choosing a wooden molding starts not with the wood species or price. First, you need to understand whether the profile will fit on the finished surface, whether its relief will be too massive, whether the frame will conflict with the handle, and whether the factory length of 2400 mm is sufficient for vertical parts without intermediate joints.
For example, let's take two identical doors measuring 600 × 2200 mm. Each requires a rectangular decorative frame with an outer dimension of 460 × 1900 mm. For MLD-024, the profile width is 40 mm, the protrusion above the surface is 25 mm, and the length of one factory strip is 2400 mm. With this configuration, the frame fits on the facade, and its vertical sides can be made solid. But four strips are only the mathematical minimum. For a real order, it is safer to consider five, because the layout on four strips leaves only about 40 mm of nominal remainder from each.
The material is chosen after checking the geometry. Beech is logical if the facade and decor will be covered with opaque enamel. Oak is if the project should keep the natural wood texture visible and semi-transparent tinting is planned. Buying oak and then completely hiding its grain with opaque paint is usually irrational. Ordering beech for a transparent finish without assessing the lamination is also risky: visible differences in lamellas may not match the intended result.

Go to Catalog

Wooden molding MLD-024: which data from the card actually affect the cabinet

The MLD-024 card specifies dimensions of 40 × 25 × 2400 mm. These three numbers cannot be perceived as one formal line: each answers a separate question of the furniture project.

Parameter MLD-024	Confirmed value	What to check on the finished cabinet
Profile Width	40 мм	Will the frame become too heavy for the door and will sufficient margins remain
Profile protrusion	25 мм	Does the decor interfere with the handle, adjacent door, wall, and full opening
Plank length	2400 мм	Can a vertical side be obtained without a transverse joint
Material	Beech or oak	What finishing is planned
Sanding	«Prestige»	What preparation remains before primer, enamel, or tinting

For a 600 × 2200 mm door, a 2400 mm long strip covers the height of the selected 1900 mm frame with a single piece. This is a strength of the model: no additional transverse joint appears on the visible vertical. However, the length of the strip alone does not mean the order is calculated. A list of all parts and a layout map of their placement in each strip is needed.
Current configuration, price, and availability should be checked directly in the product card, where you can buy wooden molding MLD-024. The price in the article should not replace the product price: warehouse data changes, and the final amount depends on material, quantity, packaging, and delivery.

Will a 40 mm wide wooden molding fit a 600 × 2200 mm door

For our scenario, the outer size of the frame is 460 × 1900 mm. If placed centered on the door, the side margin to the outer edge of the molding will be:
(600 − 460) / 2 = 70 mm.
The top and bottom margins will be equal to:
(2200 − 1900) / 2 = 150 mm.
This is not a universal recommendation for all cabinets, but a check of a specific layout. On a smooth tall door, such margins give the frame space. On a framed facade, a door with milling, or a narrow panel, the same dimensions may not fit because the base of the molding will fall on a height transition.
The profile width of 40 mm reduces the internal opening of the frame. With an external dimension of 460 × 1900 mm, the internal rectangle, without considering relief features, will be approximately:

• in width: 460 − 40 − 40 = 380 mm;

• in height: 1900 − 40 − 40 = 1820 mm.

Such a calculation is needed not only for aesthetics. If a handle, overlay, painting, or insert should be inside the frame, it is necessary to check the internal free space. If the handle is located outside the frame, measure the distance from its mounting axis and body to the nearest point of the relief.

Our factory also produces:

View Full Product Catalog

How to transfer the frame to two finished doors without accumulating errors

When facades are already manufactured, symmetry cannot be built "from each nearest edge" independently. On two doors, small errors add up and become noticeable precisely in the central gap of the cabinet.

For a door of 600 × 2200 mm and an external frame of 460 × 1900 mm, the base margins are:

• left and right — 70 mm each;

• 150 mm on top and bottom.

For a pair of doors, it is better to make one template or one measuring strip and transfer the markings to both panels from the same baselines. If the first frame is marked from the left edge of the facade, and the second is marked "by eye" from the central gap, the two frames may end up at different levels even if each is correctly sized individually.

Working order:

1. place both doors side by side in the position they will be on the cabinet;

2. mark the top, bottom, left, and right panels;

3. check the actual 600 × 2200 mm, not just rely on the design file;

4. draw a common horizontal baseline for the top side of both frames;

5. transfer the 70 mm side margins using one template;

6. compare the diagonals of the rectangles;

7. only after this, mark the cutting lines for the molding.

For a 460 × 1900 mm rectangle, the diagonal can be used as a geometry check:

d = √(460² + 1900²) ≈ 1954.9 mm.

Both diagonals of one frame must match within the accuracy required for the chosen installation method. This figure is not a tolerance from the MLD‑024 manufacturer; it is a geometric check of the rectangle.

If the diagonals differ, the frame corners are not 90°, and parts cut at 45° will start to spread apart at the corners.

The central gap between the two doors also participates in the composition.

For two doors, the frames do not exist separately. The nearest vertical sides are located on both sides of the central furniture gap.

If each frame is set 70 mm from the door edge, the visual distance between the two nearest moldings will be approximately:

70 + gap between doors + 70 mm.

With a furniture gap of, for example, 2 mm, this is about 142 mm. The specific gap here is given only as an example — the actual value should be taken from the finished cabinet.

This way, you can understand in advance whether the middle of the cabinet looks too empty or, conversely, whether the frames conflict with two handles installed near the center line.

What changes if the frame is shifted under the handle

Sometimes you want to not center the frame, but shift it slightly to make room for a long vertical handle.

Then you cannot keep the previous field formulas. You need to rewrite them:

• left field;

• right field;

• the top;

• bottom;

• distance to the handle;

• mirror symmetry of the second leaf.

For a pair of doors, asymmetry can be beautiful only if it is deliberately mirrored. A random shift of one frame by 10–15 mm will be perceived as a manufacturing error.

Why a paper rectangle is not enough to check MLD-024

Marking with painter's tape shows the width and height of the frame, but it barely conveys its volume. MLD-024 protrudes 25 mm above the surface. In a photo, these 25 mm may seem insignificant; on a smooth door next to a thin handle, the profile creates a noticeable shadow and becomes an independent architectural detail.
It is better to split the check into two stages.
First, apply tape 40 mm wide to the facade and evaluate the outer fields, inner clearance, and symmetry of the pair of doors. Then, attach a physical fragment of the profile or a mockup with the real depth of 25 mm. You need to look at the cabinet from the front, from the side, and with the doors open.
For a single private cabinet, you can order a sample strip if its remainder can be put to use. For a designer, furniture workshop, or manufacturer who regularly selects molding, it is more rational to order a set of OMLD-005 molding samples. A physical sample allows you to compare the profile with the facade, handle, color, and side light before purchasing a full-size batch.

What exactly a physical sample provides and what it does not guarantee

OMLD-005 is useful as a professional set for evaluating geometry and materials. The current card describes a case of 375 × 315 × 125 mm and a collection of samples made of oak, beech, and MDF; individual fragments are intended for applying to facades and walls.

But before publication, it cannot be automatically asserted that specifically MLD-024 is necessarily included in the current OMLD-005 configuration if the set composition is not listed by item numbers in a verified card. Therefore, the link to to order a set of OMLD-005 molding samples should be understood as a way to compare the real scale of wooden profiles. If you specifically need MLD-024, it is better to confirm with a manager whether its fragment is in the current set.

For a private cabinet, it is even more reliable to attach a real segment of MLD-024 or a full-size mockup with a cross-section of 40 × 25 mm to the door.

A mockup with a depth of 25 mm can be made in a few minutes

If you do not have a physical profile yet, take a strip of cardboard or a block:

• width of the front projection — 40 mm;

• height from the facade plane — 25 mm;

• length — at least 300–500 mm.

Secure it in the area of the future frame with masking tape.

Then:

• open both doors;

• approach from the side;

• grab the handle;

• run your hand along the frame;

• check whether the profile touches the adjacent door.

Such a simple volumetric model is more useful than a beautiful render because it allows you to feel the real protrusion.

How to check a wooden molding next to a furniture handle

The molding and the handle cannot be chosen independently. Each element has a width, a protrusion, and the area needed for the hand to grip. Even if their contours do not intersect on the front drawing, fingers may feel cramped between the handle and the relief frame.
The verification procedure is simple:

1. Mark the outer and inner contours of the frame on the facade.

2. Mark the centers of the handle's mounting holes, not just its overall size.

3. Attach the handle or a volumetric template with the actual protrusion.

4. Open the door to the full working angle.

5. Check the grip with an adult hand, the edge of the adjacent door, and the nearest wall.

6. Repeat the check on both doors: mirror placement sometimes changes convenience.

If the project requires a unified system made of natural wood, you can separately buy a wooden furniture handle Plane HL-011, but only after comparing its drawing with the MLD-024 frame. This link does not mean that Plane is automatically compatible with any layout: the length, center distance, and protrusion are chosen for a specific door.

Example of checking with the Plane HL‑011 handle

The Plane HL‑011 is useful as an example precisely because, like the MLD‑024, it has a pronounced volume. The current handle card includes a size range from 180 to 1800 mm; for example, the 500 mm variant has dimensions of 500 × 40 × 25 mm and a mounting dimension D of 384 mm.

This does not mean that the 500 mm variant should be installed on the cabinet in question. The example demonstrates the checking method.

With an outer frame of 460 × 1900 mm and a profile width of 40 mm, the inner opening is approximately 380 × 1820 mm. If the Plane 500 mm handle is placed vertically within this field, its own width of 40 mm occupies a small portion of the inner 380 mm. With ideal centering by width, the geometric field to the inner edges of the molding would be:

(380 − 40) / 2 = 170 mm

on each side.

But these 170 mm are not a "finger gap." This is only the distance in the frontal projection. Both the handle and the MLD‑024 have a protrusion of about 25 mm, so the actual grip needs to be checked by hand and from the side view.

If the handle is offset toward the inner edge of the frame, it is useful to record the minimum distance between its outer contour and the relief of the MLD‑024. The manufacturer does not specify a universal grip comfort standard in millimeters, so inventing, for example, mandatory 30 or 50 mm is not allowed.

A vertical long handle and a frame can compete in scale

The Plane HL‑011 is also available in very long variants — up to 1800 mm. On a 2200 mm door, such a handle becomes an independent vertical line almost the full height of the facade.

If the MLD‑024 frame with a height of 1900 mm is installed simultaneously, two large vertical systems will appear on the same plane:

• outer sides of the frame;

• long handle.

They can look convincing if the project is built on strict geometry, but they can also overload the facade. Therefore, first decide which element is the main one — the frame or the handle, and then choose the scale of the second.

Link to buy a wooden furniture handle Plane HL-011 is needed specifically for checking drawings and dimensional options, and not as an automatic recommendation of one specific size.

How many MLD-024 strips to order for two furniture frames

Each frame 460 × 1900 mm has four sides:

• two vertical parts of 1900 mm each;

• two horizontal parts of 460 mm each.

For two doors you need:

• four parts of 1900 mm each;

• four pieces of 460 mm each.

The total net length is:
4 × 1900 + 4 × 460 = 9440 mm, or 9.44 linear meters.
Four factory strips give:
4 × 2400 = 9600 mm, or 9.6 linear meters.
In terms of total length, the difference is 160 mm. On paper, everything looks good. Moreover, one long and one short piece can be placed in each strip:

Strip 2400 mm	Pieces	Sum of net lengths	Nominal remainder before accounting for cutting
№1	1900 + 460	2360 мм	40 мм
№2	1900 + 460	2360 мм	40 мм
№3	1900 + 460	2360 мм	40 мм
№4	1900 + 460	2360 мм	40 мм

But these 40 mm are not a full working allowance. From them, you need to account for the kerf width, possible alignment of the factory end, and the accuracy of 45° cuts. If the craftsman makes a mistake on one long piece, it won't be possible to replace it with the remainder. Two short offcuts do not form a solid vertical 1900 mm.
Therefore, there are two different answers.
Four slats are the calculated minimum for professional cutting after precise measurement and approval of all lengths using a single measurement system.
Five slats are a practical order if the work is done on-site, a test cut is required, there is no experience with this profile, or the result cannot depend on a single mistake. The fifth slat creates a reserve for the long side, and the remaining quality piece can be saved for repairs or another furniture element.
The manufacturer states that cutting to size is not performed. This means the cutting plan and responsibility for cut accuracy cannot be quietly shifted to the seller: they must be assigned in advance to the furniture workshop, installer, or the customer themselves.

Why it's necessary to agree in advance on what exactly the length of 1900 and 460 mm means for a 45° cut

For a rectangular frame with a miter joint, the same piece has two different lengths:

• by outer vertices;

• by inner vertices.

If the project simply says "1900 mm," the craftsman may interpret the size differently.

For this article, the outer frame dimension is set as 460 × 1900 mm. Therefore, it is most logical to count 1900 and 460 mm along the long side/outer miter tips, if the craftsman confirms this system.

With a profile width of 40 mm, the inner dimension then becomes approximately:

• 460 − 80 = 380 mm;

• 1900 − 80 = 1820 mm.

If the craftsman measures 1900 mm along the short side of the profile, the outer frame will become larger by twice the molding width and will no longer match the layout.

Therefore, in the cutting plan, you need to write literally:

"1900 mm — outer length from the long tip of the miter cut to the long tip."

And the same for 460 mm.

The cut makes the 1900 + 460 plan even more extreme

The clean parts occupy:

1900 + 460 = 2360 mm.

From the 2400 whip, 40 mm remains.

But when making two parts, at least one separating cut appears, and usually more is needed:

• refresh the factory end;

• make the first miter;

• make the second miter;

• fix a microchip;

• check the angle.

If the saw blade kerf is, for example, a few millimeters, those millimeters immediately eat part of the 40 mm allowance. The specific kerf width should be provided by the operator; the article does not prescribe universal 3 or 4 mm.

Therefore, the map of four whips exists only after confirming the tool and measurement method.

Why you can't assemble a 1900 mm long part from offcuts

After an error on one vertical, short pieces will remain. Theoretically, two segments can be joined, but on a visible furniture frame this will create a transverse seam.

That's why the fifth plank is not just a '10% reserve'. It insures the solid long side, which short offcuts cannot replace.

How to use the fifth plank rationally

If the four main strips are cut without errors, the spare 2400 mm does not necessarily become waste.

From it you can get:

• a spare vertical 1900 mm;

• several short repair fragments;

• test miter cuts;

• samples for color testing;

• material for another facade or a small decorative element.

For oak intended for tinting, it is especially useful to keep part of the fifth whip as a repair reserve from the same purchase.

When four slats are still rational

The mathematical minimum can be chosen if the following conditions are met simultaneously:

• the external dimensions of the frames are finally approved;

• the craftsman has already worked with this profile;

• the width of the cut is known;

• the length reference system is fixed;

• there is no need to align a significant part of the factory end;

• the cutting is done in the workshop, not on the fly at the site;

• A mistake in one part will not lead to the failure of the entire project, or there is quick access to an additional whip.

If at least two or three points are not met, the fifth bar is usually more rational than the risk of stopping the installation.

How much does a real order cost, not just the net footage

As of the product page check on August 26, 2026, one MLD-024 bar cost:

• beech — 2,630 RUB;

• oak — 3,800 RUB.

These prices should be considered dated: they may change by the time of publication or purchase.

First, the product subtotal:

Material	4 strips	5 slats
Beech	10,520 RUB	13,150 RUB
Oak	15,200 RUB	19,000 RUB

The card at the time of verification also indicated: when ordering up to five slats, a pine backing of 390 RUB is added to the invoice for transport rigidity. Therefore, for our order, it is more useful to see not only the price of the rods, but also the intermediate amount with this packaging item:

Material	4 slats + backing	5 slats + backing
Beech	10,910 RUB	13,540 RUB
Oak	15,590 RUB	19,390 RUB

These amounts do not include:

• delivery;

• saw cuts;

• miter cuts;

• glue;

• the primer;

• enamel or tinting;

• finisher's work;

• installation;

• possible painting of handles.

That is why the expression “real order amount” should be understood on two levels.

Level 1 — order from the seller: rods + applicable packaging + delivery.

Level 2 — finished frame on the cabinet: level 1 + carpentry cutting + installation + finish.

How much more expensive the spare fifth rod becomes

For beech:

13,540 − 10,910 = 2,630 RUB.

That is, the reserve increases the intermediate order by exactly the price of one beech plank; the underlay is already present in both options.

For oak:

19,390 − 15,590 = 3,800 RUB.

This is more useful than the abstract "it's better to have a reserve." The customer sees the price of insurance against an error in a long part.

Next, you can compare this amount with the cost of:

• re-delivery of one whip;

• installer downtime;

• a repeat visit;

• re-toning of the batch.

The article does not invent these costs because they depend on the city and the contractor. But the decision "4 or 5" becomes economic, not just geometric.

Why the remainder of the fifth oak plank has real value

If the facade is tinted, after a year the new oak may differ in pattern and shade. A saved fragment of the same order can be used:

• for repairs;

• to replace the short side;

• to select a new handle;

• for re-painting.

Therefore, the cost of the fifth slat cannot be assessed only as "an extra 2400 mm."

Before publishing the article, prices and availability should be re-checked in the product card. The product logic and cutting map do not change.

Beech under enamel: when to order it for a wardrobe

Beech is chosen when the wardrobe and molding must receive an opaque coating: white, colored, or dark. In this scenario, the wood grain is not the main visual effect. More important are the stable profile geometry, quality of preparation, and a unified primer system with enamel.
On the MLD-024 card, the selected beech configuration is marked as "under enamel." The official STAVROS explanation states that this version allows contrasting differences in lamellas because the surface is intended for opaque painting. This should not be confused with a ready white part: "Prestige" sanding does not replace primer and finish coating.
Beech is rational when:

• facades are also painted with opaque enamel;

• exact color matching of the frame and door is required;

• the natural texture is not planned to be left visible;

• the customer does not want to overpay for oak, whose grain will be covered anyway.

Before ordering, it is important to choose the quality and preparation of the wood for the entire group of parts, not just for the molding. If handles, legs, or overlays are ordered separately, their technological preparation must match the overall finishing system.

Oak for tinting: when texture matters more than matching enamel

Oak has a pronounced porous texture, so it is chosen for oil, clear varnish, or semi-transparent tinting. On the relief profile MLD-024, the wood grain and shadows work together. The result looks richer, but places more demands on shade selection and finishing sequence.
It makes sense to order oak when:

• the facade is made of oak or veneered with oak;

• the natural wood grain must remain visible;

• the molding is paired with oak handles, legs, or tabletop;

• a test stain sample on the same wood species has been approved;

• the customer accepts natural variations in the wood grain.

You cannot choose a shade just by looking at a screen. Even the same stain name looks different on oak, beech, veneer, and solid wood, and the profile relief changes color perception under side light. For paired doors, all slats should be tinted with the same system and in the same production cycle.

Beech and oak should be compared not only by wood species, but also by what will be visible after the finish.

In the current MLD-024 card, the "under enamel" configuration is selected for beech, while "under tinting" is available for oak. These are not marketing color names, but different requirements for re-gluing.

Under enamel, slats do not have to match in color and texture, because the surface is intended for an opaque coating.

For tinting, the lamellas are selected more carefully by color and pattern, because the wood remains visible.

Therefore, the choice can be formalized:

Project	Rational material
white/colored opaque enamel	Beech under enamel
transparent oil or varnish	Oak for tinting
semi-transparent stain	Oak for tinting
facade veneered with oak	oak after test painting
MDF facade under dense enamel	beech is more often rational

This is not a ban on painting oak with enamel. It's a question of which material feature the buyer pays for.

If the facade is already painted, the molding color needs to be checked separately.

A finished door adds an additional constraint: the main color already exists, while the molding is yet to be finished.

Even if the same paint code is used, the shade and gloss may differ due to:

• different primer;

• different absorbency;

• different layer thickness;

• side light on the relief;

• painting date;

• batch of paint materials.

For an exact match, a test coat on the actual MLD-024 material is required.

If the oak must match the door veneer

Matching "oak with oak" by name does not guarantee the same color.

Solid wood and veneer may differ:

• by cut;

• porosity;

• by grain;

• by base tone;

• by reaction to stain.

Therefore, a test oak piece is stained next to the finished door and evaluated after full drying.

Why it is better to finish two doors in one batch

If the frames are paired, all parts should be:

• cut simultaneously;

• number;

• primed with one system;

• painted or tinted in one cycle.

This reduces the risk that the left frame is visually warmer than the right.

Full absolute matching of natural oak still cannot be guaranteed, but the technological difference can be minimized.

Should the molding be painted before gluing

Both approaches have advantages and limitations.
Pre-finishing provides access to side edges and allows working on a horizontal surface. But after cutting and gluing, corner joints, end cuts, and fixing marks remain, which still require careful touch-up.
Finishing after assembly helps achieve a uniform color of the frame and facade, hide minor installation marks, and level corner joints. At the same time, hinges, the inner side of the door, and other finished elements need to be protected.
A practical order for a painted cabinet often looks like this:

1. Perform a dry layout and mark the parts.

2. Make all cuts and check the angles without glue.

3. Prepare the surface according to the selected coating system.

4. Glue the molding and perform temporary fixation.

5. After polymerization, finish the joints.

6. Apply the agreed primer and finish coats.

Specific intervals, material compatibility, and glue type are determined by the instructions of the compound manufacturers and the facade base. The general sequence can be checked in the section see tips on finishing and installation.

What to check on a finished door before applying glue

The finished facade cannot be viewed as a blank canvas. It already has or will soon have:

• hinges;

• the handle holes;

• edges;

• milling;

• paint coating;

• technological gaps;

• possibly, concealed fittings.

Before installing MLD-024, create a map of prohibited zones.

On the front side:

• handle;

• a panel;

• decorative milling;

• veneer seam;

• facade edge.

On the back side:

• hinge cups;

• screws;

• embedded parts;

• places where drilling or punching with a micro-pin is not allowed.

Even if the molding is glued only to the face, temporary mechanical fixation must not hit hidden hardware.

Why glue cannot be specified just by the word "wood"

The molding is wooden, but the door base can be:

• painted MDF;

• veneer;

• solid wood;

• laminated board;

• already lacquered surface.

Adhesion depends on the pair molding + finished facade + finish.

Therefore, the specific glue is chosen according to STAVROS recommendations and the manufacturer of the compound after determining the base. It is useful to see tips on finishing and installation, but the final decision must be confirmed by the craftsman.

Dry assembly of all eight parts before gluing

For two frames, eight parts are required:

• 4 × 1900 mm;

• 4 × 460 mm.

Before gluing, they need to be laid out directly on the doors.

Check:

• four corners of each frame;

• outer dimension;

• margins 70/150 mm;

• mirroring;

• central gap of the cabinet;

• handles;

• opening.

After that, the parts are marked, for example:

• L-V1, L-V2 — verticals of the left door;

• L-H1, L-H2 — horizontals;

• R‑V1, R‑V2;

• R‑H1, R‑H2.

This marking eliminates the situation where nearly identical parts are swapped after perfectly fitted miters.

Why angles need to be checked without glue and without putty

Putty does not fix incorrect geometry.

If the miter cuts diverge:

• the frame is not rectangular;

• the length is incorrect;

• the saw angle is not precise;

• the facade is marked incorrectly.

First, the frame is corrected. Only then is the cosmetic finishing of the seam discussed.

How to control the frame after fixation

After gluing, while the adhesive technology still allows correction, re-check:

• external dimensions;

• diagonals;

• distance to edge;

• position relative to the handle.

You don't need to check only one corner and consider the frame ready.

For two doors, it's also important to step back 2–3 meters and evaluate the pair as one cabinet.

What to do if the doors are already fully painted and cannot be repainted entirely

This is a common furniture scenario: the cabinet is assembled, the enamel on the facades is ready, and the MLD-024 frame was decided to be added later.

In this case, the finishing order changes.

For a beech under enamel, you need to decide in advance how to achieve visually the same color without repainting the entire door. Practically, two approaches are possible:

Paint the molding separately before installation.

Advantages:

• the facade does not fall into the painting zone;

• it is convenient to paint the side edges of the profile;

• it is easier to work on a horizontal table.

Disadvantages:

• after cutting the corners, the ends are exposed;

• the glue seam cannot be covered with the common enamel;

• the slightest difference in shade from the finished door will be visible at the wood/facade boundary.

Install the prepared molding and locally finish the frame.

Advantages:

• you can refine the corners after assembly;

• it is easier to get a holistic view of the frame itself.

Disadvantages:

• the finished facade needs to be carefully masked;

• local spraying or touch-up painting can cause a difference in gloss;

• the risk of damaging the existing coating is higher.

There is no universally best method. It is chosen by the finisher and furniture maker after testing.

The test coating should include not only color but also gloss

Two surfaces of the same color can look different if one is matte and the other is semi-matte.

On the MLD-024 relief, side lighting enhances this difference.

Therefore, the control sample is compared:

• frontally;

• at an angle;

• in daylight;

• with the room lighting turned on.

For oak, additionally check how the tinting works on the ends of miter cuts: end grain wood may absorb the compound differently than the longitudinal surface.

If the finished facade is veneered, the frame cannot be glued without checking the coating

The veneer may be coated with:

• with varnish;

• with oil;

• with enamel;

• other finish.

The adhesive contacts not "wood in general," but the finished coating of the facade. Therefore, adhesion must be confirmed specifically for that surface.

You cannot mechanically transfer a recommendation suitable for unpainted solid wood to an already lacquered door.

A hidden test is especially useful on an internal technological part

If the project has a separate facade sample or an invisible technological piece with the same coating, you can check on it:

• adhesion;

• cleaning up excess;

• the effect of masking tape;

• solvent compatibility;

• finish behavior.

This is safer than conducting the first experiment on a finished cabinet door.

When MLD-024 does not need to be purchased for ready-made doors

Abandoning a specific profile sometimes saves more than trying to fit it into already manufactured furniture at any cost.
MLD-024 is better not to order if the 40 mm width takes up too much of a small door, the profile base falls on a milled transition, the 25 mm protrusion interferes with the handle grip, or the door comes too close to the wall when opening. It is also not suitable if the project requires a flexible profile for a curved line: the card describes a straight wooden molding 2400 mm long.
Do not buy four strips without a reserve if the exact external dimensions of the frames are not yet approved. Changing each short side by just 20 mm will destroy the 40 mm margin on the stick. The 1900 + 460 map will no longer work if, after fitting, the frame width is decided to be increased to 500 mm.
If a physical fitting showed that MLD-024 is too massive, the correct next step is — buy wooden moldings for furniture smaller width or depth after comparing drawings. The profile substitution should occur by dimensions and actual

Oak is ordered under opaque enamel without reason

The buyer pays for a more expensive material and then completely hides its main visual advantage — the texture.

They consider "Prestige" a ready-made coating.

This is the quality of sanding, not a finished enamel or tinting.

They hope to receive parts already cut to size.

The FAQ on the card directly states that the service of filing or cutting to size is not provided. The contractor and the cutting map must be determined in advance.

They buy the entire batch without a single volumetric fitting.

The tape shows the contour, but not the depth of the shadow or the comfort of the grip. A fragment of the real profile reveals the problem before paying for the full batch.

How changing the frame size after fitting changes the quantity of MLD-024

For ready-made doors, the frame size is often adjusted after the volumetric fitting. This is a dangerous moment: it seems that a change of 20–40 mm "changes nothing," but the limit map 1900 + 460 is very sensitive to every addition.

The original scheme of one strip:

1900 + 460 = 2360 mm.

Nominal remainder:

2400 − 2360 = 40 mm.

Now let's see what happens if the frame's appearance changes after fitting.

Outer short side	Layout on one stick with vertical 1900	Remainder before cut
440 мм	1900 + 440 = 2340	60 мм
460 мм	1900 + 460 = 2360	40 мм
480 мм	1900 + 480 = 2380	20 мм
500 мм	1900 + 500 = 2400	0 мм

At 500 mm, four sticks are no longer a real map: the clean lengths take up the entire factory strip, leaving no room even for the separating cut and end processing.

That is, the designer's phrase "let's widen the frame by just 40 mm" can automatically move the order from mathematical four sticks to five.

The same happens when increasing the frame height

If the width remains 460 mm, and the vertical becomes:

1920 mm, we get:

1920 + 460 = 2380 mm.

20 mm remain to the cut.

With a vertical of 1940 mm:

1940 + 460 = 2400 mm.

The margin disappears completely.

Therefore, the cutting map is approved after a full-scale fitting, not before it.

Why you cannot order four rods "while the designer is thinking"

If four planks are already purchased and then the frame is enlarged, the customer becomes psychologically attached to the material and starts adjusting the design to fit the remainder.

It is more correct to complete the stages in the following sequence:

mockup → handle → opening → outer frame size → cutting map → number of rods → order.

How reducing the frame can provide useful technological margin

If after fitting the outer width of 460 mm seems too large and the frame is reduced to 440 mm, one sash contains:

1900 + 440 = 2340 mm.

Nominally, only 60 mm remains.

The additional 20 mm on each of the four sashes does not make cutting error-free, but gives the craftsman more room for sawing and trimming.

Thus, the aesthetic solution simultaneously improves manufacturability.

You cannot change only one door leaf.

If two leaves form a pair, the frame change must be synchronized.

You cannot, after an error on the right door, reduce only its short sides by 20 mm to "fit into the remainder." The two frames will no longer be mirror images.

Decision tree for ordering four or five slats

Are the frame dimensions final?

• no → do not order;

• yes → build the map.

Does each whip leave less than 50 mm to the cut?

• yes → extreme cutting, especially carefully count the tool;

• no → the margin is more comfortable, but still check.

Does the master guarantee the map and have experience with miter cuts?

• yes → four can be discussed;

• no → the fifth plank is more rational.

Is repeat delivery of one whip expensive or slow?

• yes → the reserve is especially valuable;

• no → you can take a higher risk of the mathematical minimum.

This decision tree is more useful than the automatic formula "perimeter + 10%."

What to write in the specification before placing an order

A good specification for our example fits on one sheet:

Field	Entry for the project
Product	Wooden molding MLD-024
Facades	2 pcs., 600 × 2200 mm
Outer frame size	460 × 1900 mm on each door
Pieces	4 × 1900 mm; 4 × 460 mm
Net length	9440 мм
Factory length	2400 мм
Minimum	4 strips
Work order	5 slats in the absence of error-free industrial cutting
Material	Beech under enamel or oak under a translucent finish
Handle	Article number, overall size, mounting base, protrusion
Cutting operator	Specific workshop or installer
Finish	Primer and finish system, test paint-out

A frontal drawing of the doors, profile cross-section, handle placement, and a photo of the 3D mock-up are attached to the sheet. After this, the order becomes verifiable: the manager sees the specific article number and quantity, the craftsman receives the part dimensions, and the finisher gets a clear material and finish.

How to distribute MLD-024 slats after delivery and before the first cut

Even a correctly calculated order can be ruined if you immediately grab the first available strip and start cutting a 1900 mm vertical. For two paired facades, it is better to first turn the received batch into a clear set of parts.

First, the entire order is checked.

Before cutting, lay out the strips and check:

• article MLD‑024;

• profile size 40 × 25 mm;

• factory length 2400 mm;

• material — beech or oak;

• selected preparation;

• quantity;

• absence of transport damage that will fall into the visible part of the frame.

If five strips are ordered, all five need to be assessed before the first one becomes an irreversible 1900 mm segment.

For oak, it is useful to assign pairs in advance

On two doors, four long verticals are especially noticeable. The natural oak pattern does not repeat like printed decor, so before staining it makes sense to lay the strips side by side and decide which two verticals will be on the left door and which on the right.

The task is not to achieve artificially identical grain. The task is to avoid a random composition where one vertical is very calm and the neighboring one is sharply contrasting, if the project did not intend this.

After distribution, the strips are marked.

For example:

• No. 1 — left door, left vertical;

• No. 2 — left door, right vertical;

• No. 3 — right door, left vertical;

• No. 4 — right door, right vertical;

• No. 5 — reserve and test cuts.

Short 460-mm parts with a 1900 + 460 layout are made from the same strips.

It is better to use the reserve strip first as a technological one

If five strips are purchased and the craftsman is working with MLD-024 for the first time, it is logical not to save the fifth until the last minute, but first make on its end:

• a test cut at 45°;

• checking the edge cleanliness;

• saw setup test;

• minor chipping;

• glue test on a non-visible area.

After the test, the remaining length of the reserve strip may still be sufficient to replace a short piece or, if the test cut is minimal, for the long side. The specific length of the test piece is agreed upon by the master.

Why long verticals are cut with the most control

The short side of 460 mm is easier to replace from the remainder.

A vertical of 1900 mm requires almost a full stick. An error on it has the maximum cost.

Therefore, a reasonable order of work:

1. set up the saw on a test piece;

2. confirm the long/short top system;

3. make the first vertical;

4. check it on the door;

5. only after that replicate the rest.

No need to first cut all eight parts according to the list, and then apply them to the facade for the first time.

Checking 2400-mm strips indoors

The trim is long. Before ordering, it is useful to make sure that it can be:

• received from the carrier;

• brought into the room;

• unfolded near the wardrobe;

• Safely place for cutting.

For this article, logistics is not the central intent, but it affects the real cost of the order. A 2400-mm oak whip damaged during handling turns the savings on the fifth plank into a repeat purchase.

After cutting, keep the markings until installation.

Miter joints are individually fitted. Even if four short pieces have the same nominal length of 460 mm, swapping them after dry assembly is not advisable.

Each corner is already matched to the specific adjacent piece.

The markings must survive:

• sanding;

• Priming;

• temporary storage;

• transport to the site.

They are placed in a hidden area or use removable tags to avoid damaging the face surface.

How to place a commercial order without an extra plank and without the risk of stopping work

First, approve the appearance. Apply tape 40 mm wide, attach the 3D sample MLD-024, and check both doors in closed and open positions. Then fix the outer size of the frames and compile a list of individual parts.
After that, request from the contractor the actual cutting width and the method of mitering corners. If the craftsman confirms in writing the cutting plan of 1900 + 460 from each stick and takes responsibility for cutting, you can discuss the mathematical minimum of four planks. If the work is done for the first time or on site, a fifth plank is not a pointless overpayment, but insurance for a long piece that cannot be restored from short remnants.
Only then choose the material. For covering paint, consider beech under enamel. To preserve natural texture, use oak and an agreed tinting system. Check the current price, availability, backing, delivery, and lead times immediately before payment.
This order answers the main commercial question better than the formula "perimeter plus ten percent." The buyer understands not only how many meters they need, but also which profile suits the finished furniture, why four sticks are the maximum cutting plan, when a fifth is needed, and what they are paying for in the beech or oak option.

FAQ

Can MLD-024 be used on a furniture facade?

Yes, if the flat area of the facade accommodates the profile base 40 mm wide, the 25 mm protrusion does not interfere with the handle and opening, and the chosen scale matches the door. Before purchasing, a drawing and a 3D fitting are needed.

How many MLD-024 planks are needed for two frames 460 × 1900 mm?

The net length is 9.44 m. The theoretical cutting plan fits into four planks of 2400 mm: from each, you get 1900 + 460 mm. The margin is only 40 mm before accounting for the cut, so for work without room for error, it is reasonable to order five planks.

Why can't you simply add 10% to the perimeter?

A percentage margin does not verify the placement of individual lengths in the factory stick. For linear materials, both the total length and the cutting plan matter.

What to choose under white enamel — beech or oak?

Usually beech in an enamel finish. Oak makes sense when its pronounced texture is left visible under a translucent finish.

Is painting included in the price of the molding?

The card shows the material, sanding, and preparation, but sanding is not a finish coating. Painting conditions and the availability of the service need to be checked separately before ordering.

Can MLD-024 be ordered already cut to frame sizes?

The FAQ on the product page states that undercutting and cutting to size are not provided. Cutting is arranged by the customer through a workshop or installer.

Why check the profile with the door open?

The front drawing does not show possible contact with the wall, adjacent door, and handle. The protrusion of MLD-024 is 25 mm, so a volumetric check is performed with full working opening.

Can MLD-024 be installed on a curved facade?

This is a straight wooden profile. For a curved task, a different technical solution is required; a straight strip cannot be considered flexible without manufacturer confirmation.

What happens if, after fitting, the frame is increased to 500 mm in width?

With a vertical of 1900 mm, one long and one short piece will take up:

1900 + 500 = 2400 mm.

That is, the net lengths completely consume the factory whip and leave no room for cutting and end processing. In this option, four slats cease to be the working minimum: additional material or a different cutting plan is needed.

Can the left frame be made of beech and the right one of oak?

Technically, different materials exist, but for paired doors this almost always creates an unnecessary visual difference. Under a transparent finish, oak and beech read differently; under enamel, mixing also provides no practical advantage. For a pair of leaves, it is better to choose one wood species and one preparation system.

Does the OMLD-005 set guarantee the presence of the MLD-024 sample?

The verified OMLD-005 card describes a large set of real profiles, but the composition is not listed by all article numbers. Therefore, the presence of specifically MLD-024 in the current configuration of the set should be confirmed with a manager. If the choice depends specifically on MLD-024, a real fragment or a full-size mock-up of 40 × 25 mm is needed.

Is there any point in storing the remainder of the fifth slat after installation?

Yes, especially for oak under tinting. The remainder from the same purchase can be used for repairs, re-staining, or replacing the short side. This is the practical value of a reserve, which an abstract 'percentage of stock' does not have.