The old mirror was removed, two anchors remain in the wall: how to buy Versailles 008-002 and check existing mounting points

The old mirror was removed, the wall is already finished, and you want to keep the two anchors. At this stage, it's easy to make a mistake: seeing the width of 883 mm on the new Versailles 008-002, applying a tape measure to the old holes and deciding that this figure can indicate compatibility. It cannot. 883 mm is the external size of the finished mirror, not the confirmed distance between the hangers.

Before purchasing, you need to compare two independent diagrams. The first is the coordinates of the existing points on the wall: the distance between centers, the height of each point, and the position of the common axis relative to furniture and the wall. The second is the actual rear mounting diagram of the Versailles 008-002: the number of hangers, the center-to-center distance, the vertical offset from the top edge, the orientation, and the fixing method. If these data are not compared, the old anchors cannot yet be considered part of the new installation.

Versailles 008-002 is a finished mirror in a carved wooden frame measuring 1500 × 883 × 44 mm. For current retail options, beech with white enamel RAL 9010 and oak with a walnut patina tint are specified. The price as of September 7, 2026, is 137,700 ₽ and 181,750 ₽, respectively. The difference is 44,050 ₽. The product is made to order in an average of 5–10 days and is delivered in a rigid box.

Versailles Carved Frame Mirror 008-002

from 1,662.03 $

Go to Catalog

Versailles 008-002 mirror: what can be checked on the product page before purchasing

From the product page, the product dimensions, frame material, finish, price, and delivery format are known. This is enough to understand whether the mirror fits on the chosen wall and suits the style. However, this data is insufficient for reusing old mounting points.

Key practical conclusion: the external width of the product cannot be used as a mounting template. On the front view, the mirror may perfectly align with the wall, but the old anchors may end up at a different height or with a different center distance.

If the format and finish already suit the interior, Buy mirror Versailles 008-002 it is reasonable after receiving the rear mounting diagram.

Watch video ...

Two old anchors: what dimensions to take before ordering a mirror

Old holes should be described not with words like "approximately in the center," but with coordinates. For example, the distance between anchor centers turned out to be 600 mm. This is only a training example, not a characteristic of Versailles 008-002.

For each point, record:

• distance between anchor centers;
• height of the left anchor center from the finished floor;
• height of the right anchor center from the finished floor;
• position of the middle of the pair relative to the center of the wall;
• position of the middle of the pair relative to the console, dresser, or other furniture;
• clear space up to the ceiling cornice, sconce, and the top edge of the furniture.

If the anchors are at different heights, do not average them in your head. Record both values. Even a difference of a few millimeters is important at the geometry check stage, because it shows that the old system could have been mounted asymmetrically or designed for a different type of suspension.

It is convenient to make a simple table of the object:

After such measurement, old anchors become not "two holes that are a pity to lose," but a measured coordinate system.

Our factory also produces:

Mirror Frame RM-018

from 1,430.29 $

Mirror frame RM-016

from 1,532.64 $

Mirror Frame RM-020

from 742.18 $

Mirror Frame RM-014

from 1,241.88 $

Mirror frame RM-002

from 1,338.07 $

Mirror Frame RM-008

from 803.62 $

Mirror frame RM-010

from 835.48 $

RM-017 Mirror Frame

from 1,816.53 $

View Full Product Catalog

Center of old mounting and center of new mirror: check composition before installation

If two old anchors are spaced 600 mm apart, the geometric center of the pair is 300 mm from each point. This allows determining the axis of the old mounting on the wall. But this calculation does not indicate where the hangers of the new mirror are located.

Four axes need to be checked:

1. geometric center of the free wall;
2. center of the console or dresser under the mirror;
3. center of the existing pair of anchors;
4. desired center of Versailles 008-002.

When all four coincide or create a deliberate composition, the old points at least do not force the mirror to be shifted. If the anchors were made for the old mirror, which hung 70 mm to the right of the furniture, keeping these points will simply repeat the previous mistake.

Therefore, the question "can the holes be left?" splits into two. First — whether they will spoil the position of the new mirror. Then — whether they match the actual Versailles hanging system.

Full-size template 1500 × 883 mm: we check not only the anchors but also the final height of the mirror

After receiving the hanging scheme, it is useful to transfer it not directly to the wall, but to a paper or cardboard template measuring 1500 × 883 mm. On the template, mark the top, the central axis, and the actual hanging points according to the manufacturer's confirmed coordinates. Then apply the template to the old anchors.

This makes several things visible at once: where the top of the decorative frame will be, how low the bottom edge will drop, whether the center aligns with the console, and whether the top threading will hit the ceiling cornice, sconce, or another element.

If the scheme indicates that the hanging center is located at a distance of t millimeters below the top edge of the product, the height of the top edge can be calculated as follows:

height of the top of the mirror = height of the hanging center + t.

The lower edge when mounted vertically is then 1500 mm below the upper edge. Here, t is not a known Versailles value, but a variable that must be taken from the actual mounting diagram.

For example, if two old anchors are at the same height, but after substituting the real t, the lower edge of the template ends up too high above the console, the center-to-center alignment does not save the project. Geometrically, the anchors fit, but compositionally, they do not.

The template also helps check the 883 mm width relative to the wall and furniture. Mark the central axis on it and compare it with the console axis. If the old anchors shift the template to the side, this is visible before the mirror is delivered.

To compare other ready-made solutions, you can separately buy a wall mirror in a frame from the same category, but each model is checked against its own rear mounting diagram.

What mounting diagram for Versailles 008-002 should be obtained before payment

Before placing an order, request not the general front drawing, but the rear mounting diagram of the specific product. Specific parameters are needed:

• how many hangers are provided;
• the distance between their centers;
• vertical position relative to the top edge of the mirror;
• position relative to the central axis;
• type of intended suspension;
• permissible orientation of the product;
• what is included in the rear mounting system.

In the open description of the card, these coordinates are not published. Therefore, you cannot write "Versailles definitely has two hinges," even if the old mirror had two.

It is useful to request a diagram with dimension arrows and mark the old anchors on it. Then one of three results appears: complete match, geometric mismatch, or distance match with incorrect height.

It is the third case that is often overlooked: the distance may match perfectly, but the mirror will be higher or lower than the intended position.

The old anchors matched in coordinates: does this mean they can be left?

No. Coordinate match is only the geometric part of the check.

You also need to know what the wall is made of and what exactly is inside the old hole. Brick, concrete, solid block, hollow structure, and framed partition require different solutions. The old anchor could have been designed for a different mirror, installed with an error, damaged during removal, or partially spun out.

Also check the compatibility of the head, hook, or other protrusion of the old fastener with the new hanging system. Even identical coordinates do not turn two different mounting points into the same one.

Therefore, the safe formula is:

coordinates matched + wall construction confirmed + fastener condition checked + compatibility with the Versailles mount confirmed = keeping the old points can be considered.

If at least one element is missing, the installer makes the decision after inspection.

General manufacturer recommendations can be found in the section tips for installing wooden products, but they do not replace the calculation of a specific wall mounting point.

The distance matched, but the mirror turns out to be too high

Let's imagine that the center-to-center distance of the old anchors and the new mirror matched. That is not yet a victory. If the vertical offset of the hangers from the top edge differs for Versailles compared to the old mirror, the new product may end up 50–100 mm higher or lower than the desired line.

This is especially noticeable above a console or dresser. Visually, the mirror may "detach" from the furniture or, conversely, drop too close to its top surface.

You cannot fix the situation by arbitrarily moving hinges on a carved wooden frame, drilling the back part, using random wire, or using one hanger instead of the intended system. Such changes must be confirmed by the product's design.

If the manufacturer allows adjustment of the standard unit, it can be used within the scheme. If there is no adjustment, it is more correct to move the mounting in the wall than to redo a finished mirror worth more than one hundred thousand rubles.

Old points do not fit: is it worth changing the mirror just for the holes

Here a real buyer's fork arises.

If Versailles 008-002 fits perfectly in size, finish, and composition, but the old points do not match, it is usually more reasonable to make a new correct installation and restore unnecessary holes. Two old anchors are a weak reason to refuse a suitable expensive item.

If repeated drilling is truly impossible—for example, the wall is faced with rare stone, a panel with a limited mounting zone, or has an already approved hidden engineering system—then you need to compare the real hanging schemes of other finished mirrors in advance, rather than choosing a model only by external size.

For such a selection, you can buy a mirror in a wooden frame from the general category of finished classic mirrors. But another model does not guarantee a match with the old holes: its rear scheme is also checked separately.

If maximum freedom under the existing wall unit is needed, you can move to independent design of the frame and panel. This is a different product scenario; buy mirror frame leads precisely to separate frames, not to the finished Versailles.

Finished mirror above the console: old holes should not dictate the new composition

Versailles has an external size of 1500 × 883 mm. When placing it above furniture, you first need to check the proportion of the entire composition, and only then try to preserve the old anchor points.

Fix the width of the console, its central axis, and the free margins of the wall. Then apply a full-size rectangle of the mirror to the wall using painter's tape or a paper template. After that, mark the actual old anchors.

If the old anchor points force the mirror to noticeably deviate from the center of the furniture, preserving the holes should not be considered a priority. The previous model could have been narrower, wider, had a different decorative top, or simply hung where the new mirror does not look better.

There is no need to assign universal 150 or 200 mm between the furniture and the frame. Versailles has a height of 1500 mm, so the position depends on the height of the furniture, ceiling, cornice, wall sconces, and the overall wall. A full-size template provides more benefit than a "correct" number from general advice.

You can compare Versailles itself with another large classic model in the material compare Versailles 008-002 and Luxe 008-004, but the new task with old anchors is solved only according to the rear mounting diagram.

White Versailles or oak "walnut with patina": choose the finish after checking the location

After the position and mounting are confirmed, you can choose the finish.

The difference is 44,050 ₽.

White enamel logically works in light classic compositions, especially next to white doors, baseboards, and furniture. Walnut with patina gives a darker and more contrasting effect. But the specific color should be viewed next to the actual wall and furniture, not just on the screen.

Material and coating do not solve the problem of old anchors. Therefore, the choice of finish comes after geometry and the mounting scheme. Details on materials and surface preparation are collected in the section conditions for selecting materials and finishes.

Full price of mirror replacement: old holes do not guarantee savings

Having two anchors creates the feeling that installation is almost paid for. In practice, savings may be zero: old points may not align, fasteners will have to be replaced, and unnecessary holes restored.

The full budget is better calculated as separate line items:

Versailles 008-002 + delivery + lifting + installation + inspection of old points + new fasteners if necessary + restoration of extra holes.

There is no need to add a separate cost for the mirror panel: Versailles 008-002 is a ready-made mirror in a frame, not an empty wooden frame.

The rigid box also affects logistics. Before ordering, check the delivery route: doorways, stair turns, elevator, corridor, and temporary storage space. For a product 1500 mm high, this is usually easier than for large full-size models, but it still needs to be checked.

Current delivery calculation terms can be clarified on the page the payment and delivery terms for the mirror.

What mistakes make old holes the main risk of the project

The first mistake is measuring the distance between the edges of anchors instead of the distance between their centers. If the fastener diameter differs, the result will be incorrect. Centers are needed for comparison with the suspension diagram.

The second mistake is measuring only the center-to-center distance. Two anchors can be at the correct distance but at the wrong height. Therefore, vertical coordinates of each point are needed.

The third mistake is considering the external size of 883 mm as the distance between suspensions. These are different parameters.

The fourth mistake is not checking the condition of old anchors. After dismantling the previous mirror, the fasteners could have become loose, received lateral load, or partially come out of the base.

The fifth mistake is transferring the old mirror's system to the new one: "it used to hang on two points, so we will hang the new one the same way." The number and type of suspensions are determined by the design of the new product.

The sixth mistake is choosing a new model only for the sake of matching holes. As a result, the mirror may not be centered on the furniture, be too high, or not fit in scale.

The seventh mistake is independently reworking the back part of a carved wooden frame. For an expensive finished product, this should be an agreed-upon step, not an improvised one.

What to send to the STAVROS manager before ordering

It is better to make the request specific:

Versailles 008-002 / 1500 × 883 × 44 mm / selected finish.

After the previous mirror, two mounting points remain on the wall. The center-to-center distance between the centers is ___ mm. The height of the left point from the finished floor is ___ mm, and the right one is ___ mm. The center of the pair relative to the furniture is ___ mm.

Please confirm the current rear mounting scheme for Versailles 008-002: the number of hangers, center-to-center distance, vertical offset from the top edge of the product, position relative to the central axis, type of hangers, and completeness.

Attach a photo of the entire wall, close-up photos of both anchors with a ruler, and a photo of the furniture under the mirror. The manager needs the product parameters and the existing wall. The installer additionally needs the wall material and the actual condition of the old mounts.

Once the scheme is received, it is convenient to overlay: old points in one color, new hangers in another. Then the solution is visible without guesswork.

What to photograph on the wall before the installer arrives

Before dismantling old anchors or attempting to unscrew them, take several technical photos. The overall shot should show the entire wall, the furniture under the future mirror, and both points simultaneously. Separately, photograph each anchor close-up—frontally and from the side, next to a ruler. This will show its protrusion from the wall and the condition of the surface around the hole.

It is also useful to photograph the base material where it is known: a brick joint, concrete, cladding, decorative panel, or drywall system. If the wall is covered with finish and the base is unknown, this is directly noted in the installer's task.

In one photo, you can place a tape measure between the anchor centers, but the final value is still recorded separately as a number. The photo serves as confirmation and helps spot a measurement error, not as a replacement for the dimension sheet.

After this, the old points can be discussed concretely: the installer sees their condition, the manager receives the coordinates, and the buyer does not risk losing the original information before the Versailles scheme is obtained.

When not to buy Versailles 008-002 yet

It is better to postpone the order if preserving the old holes is a mandatory condition, and the mounting pattern for the new mirror's hangers has not yet been received.

Do not buy a mirror if the coordinates of the old points have not been measured from the centers or differ in height, but this has not yet been taken into account. The same applies to a situation where no one has checked the condition of the fasteners and the wall material.

The purchase is premature if keeping the old anchors shifts the mirror relative to the furniture or raises it to an undesirable height. A new expensive item should not inherit the erroneous composition of the old one.

A stop signal is the intention to drill or move elements on the back of a wooden frame yourself without a confirmed mounting pattern.

If installation without a single new hole is needed, this condition must be set before choosing the model and checking ready-made mirrors specifically against the hanger patterns.

FAQ: Versailles 008-002 and existing anchors

What is the size of Versailles 008-002?

The finished mirror has dimensions of 1500 × 883 × 44 mm.

Is 883 mm equal to the distance between the hangers?

No. 883 mm is the external size of the product. The center-to-center distance of the rear hangers must be obtained from the mounting pattern.

Can I use the anchors from the old mirror?

Only after matching coordinates, checking the condition of the fasteners, wall material, and compatibility with the standard Versailles mount.

How to correctly measure the center-to-center distance?

Between the geometric centers of two points, not between their edges.

What to do if the anchors are at different heights?

Record both heights separately. Do not average them. Then compare them with the required coordinates of the mounts for the new mirror.

What diagram should I request from the seller?

Rear view with the number of mounts, center-to-center distance, vertical offset from the top edge, position relative to the axis, and mounting type.

Is matching the distance between the anchors sufficient?

No. The vertical coordinate, node compatibility, and suitability of the old fasteners are also needed.

Can the mounts be repositioned on the frame itself?

Independently — only if the manufacturer explicitly allows it. Without such information, you should not modify the back of a finished mirror.

What to do if a mirror with suitable anchors ends up off-center?

Priority is proper composition and safe installation. Usually, it's better to create new mounting points than to keep an incorrect position.

Is wall mounting hardware included in the set?

The specific contents of the wall mounting hardware are not disclosed in the open product card. This should be clarified before ordering.

How much does the white finish cost?

As of the check on September 7, 2026, the beech Versailles in white enamel RAL 9010 is 137,700 ₽.

How much does the oak finish cost?

The oak Versailles in a walnut with patina finish is 181,750 ₽ as of the check.

Is Versailles a ready-made mirror?

Yes. This is a finished mirror in a carved wooden frame, not a separate empty frame.

When exactly are new mounting points needed?

When the hanging scheme does not match the old coordinates, the old anchors are unsuitable, or their position disrupts the desired composition.

What to do with unnecessary old holes?

After selecting new points, they are restored using a method suitable for the wall material. The specific technique is chosen based on the finish and the substrate.