Buy wooden slats: RK-001 solid wood 2400 mm or interior RK-002 MDF with oak veneer 2750 mm — which to choose

Wooden slats can be purchased for completely different tasks: to finely outline a furniture facade, to assemble a calm wall layout, to create a deep vertical relief, to decorate a ceiling, or to zone a room. The mistake begins when all these tasks are attempted with the same plank. RK-001 and RK-002 externally belong to the same group, but differ in material, length, cross-sections, and the very logic of installation.

RK-001 is a straight slat made of solid beech or oak, 2400 mm long. It is available in seven cross-sections: from an almost flat strip of 15 × 5 mm to a large profile of 80 × 23 mm. Beech is prepared for enamel, oak for tinting. This choice is suitable for precise layouts, furniture facades, frames, small panels, and projects where real solid wood is important.

RK-002 is an interior slat 2750 mm long. It is made of MDF for painting or MDF with oak veneer and is offered in sizes 16 × 40, 22 × 60, and 40 × 40 mm. The profile creates a pronounced volume and deep chiaroscuro, and the mounting system includes an insert of 20 × 8 mm. This model is primarily designed for walls, ceilings, decorative inserts, and large-scale zoning.

The choice between two SKUs cannot be reduced to the question of "wood or MDF." The buyer needs to simultaneously check the finished height, desired relief depth, number of slats, spacing, finishing method, wall material, presence of baseboard and cornice, as well as the possibility of installing a mounting plate. The article helps navigate this path and understand which specific product to put in the cart.

Buy RK-001 Buy RK-002 View all slats Order samples

Go to Catalog

RK-001 and RK-002: confirmed specifications

How RK-001 differs from RK-002

RK-001 — solid wood slat. Even the thinnest options retain the character of natural wood, and seven cross-sections allow for very different graphics: dense, sparse, flat, or moderately voluminous.

RK-002 — a system with an MDF base. In the wood version, the surface is formed by oak veneer, not solid wood. Such a slat cannot be called solid oak.

The second difference is depth. RK-001 has flat options with a thickness of 5–10 mm, while RK-002 creates a noticeable protrusion and shadow.

Third — installation. RK-002 is designed together with a mounting plate, while RK-001 requires a separate choice of fastening based on the base and task.

Our factory also produces:

View Full Product Catalog

When to buy a wooden slat RK-001

RK-001 is suitable for a project where solid wood, precise cross-section, and the ability to choose beech or oak are essential.

Thin options are convenient for furniture, small wall panels, frames, headboards, and decorative strips. Larger cross-sections allow for noticeable verticals without extreme depth.

The length of 2400 mm is sufficient if the finished area is shorter or the layout allows for horizontal use.

For such a project you can buy a wooden slat RK-001 and select the desired cross-section in the product card.

When to choose interior RK-002

RK-002 is needed where the batten should become a volumetric architectural element, not just a strip on a plane.

The length of 2750 mm helps to work with a high wall and ceiling, but it is still compared to the finished height, baseboard, cornice, and expected trimming.

MDF under enamel is suitable for a solid layout in the color of the wall. MDF with oak veneer preserves the natural surface pattern with a stable base.

If a large relief is needed, you can buy interior batten RK-002 and check the installation through the embedded element.

Solid oak or MDF with oak veneer

Both models can look like oak, but are constructed differently. RK-001 made of oak consists of natural wood throughout the cross-section. RK-002 in the wood version has an MDF base and an outer oak veneer.

Solid wood is chosen when natural wood is important not only on the surface but also in the detail itself. This is relevant for furniture, open ends, and projects where the material must be honestly readable.

Veneered MDF base is suitable for large repeating layouts where stable geometry and a natural oak surface appearance are needed.

When comparing, one cannot say that one option is universally better. You need to decide what is more important: solid wood throughout the cross-section or a volumetric profile on a stable base.

Beech for enamel or MDF for painting

The beech RK-001 and MDF version RK-002 are both designed for opaque finishing, but offer different construction.

Beech retains a solid wooden base and is suitable for furniture, frames, and parts that must be wooden even under enamel.

MDF is convenient for large interior systems with repeating profiles. The uniform surface helps achieve an even color across the entire wall.

The choice is made based on scale and depth: for thin layouts — RK-001, for pronounced volume — RK-002.

Length 2400 or 2750 mm

The difference between the models is 350 mm. On paper, this seems like a small advantage, but with a high wall, it can solve the issue of a seamless vertical.

RK-001 with a length of 2400 mm is suitable for standard sections, furniture, horizontal layouts, and walls where margins are provided at the top or bottom.

RK-002 with a length of 2750 mm is useful for a ceiling of about 2700 mm, if after deducting the baseboard, cornice, and technological gaps, the rail fits without a composite joint.

You cannot choose the length only by the ceiling height. First, measure the finished section from the actual lower to the upper mounting point.

What to choose for a ceiling height of 2700 mm

With a ceiling of 2700 mm, RK-001 with a length of 2400 mm will not cover the entire height with a solid vertical if the rail goes from floor to ceiling.

RK-002 with a length of 2750 mm is potentially better suited, but you need to consider the baseboard, cornice, trimming, and the exact mounting assembly.

If the layout starts above the baseboard and ends below the cornice, the actual length may be less than the nominal room height.

Before ordering, make a vertical section of the wall and indicate the finished size of each rail.

How to choose the section RK-001 15 × 5 mm

The thinnest section is suitable for graphic layouts, small facades, frames, decorative strips, and frequent spacing.

A thickness of 5 mm creates a delicate shadow and barely protrudes into the passage.

On a large empty wall, such a batten can get lost, especially with a large distance between elements.

It is better to choose 15 × 5 mm based on a full-size sample: a thin line looks different on the wall than in the hand.

How to choose sections 24 × 5 and 40 × 5 mm

These options maintain a small depth but make the strip more noticeable.

24 × 5 mm is suitable for furniture doors, small panels, mirror frames, and frequent wall geometry.

40 × 5 mm works better on larger surfaces and allows increasing the spacing without losing readability.

Both profiles are convenient where a pattern is needed but a strong protrusion is undesirable.

What are RK-001 70 × 7 and 90 × 10 mm for?

Wide flat battens create calm large verticals and noticeable stripes without the depth of RK-002.

70 × 7 mm is suitable for large wall fields and furniture panels where a confident scale is needed.

90 × 10 mm forms an even wider strip and can be used with a rare pitch.

Before choosing, check that the wide batten does not overlap sockets, switches, and free areas around furniture.

When to choose RK-001 60 × 23 and 80 × 23 mm

These sections already provide a pronounced relief and are suitable for large furniture, voluminous frames, and noticeable interior inserts.

The depth of 23 mm creates a shadow, but the structure remains a solid solid wood batten.

60 × 23 mm appears more elongated, 80 × 23 mm is more massive and calmer with a rare pitch.

If even greater depth or a system with a mounting insert is needed, it is worth comparing RK-002.

How to choose RK-002 16 × 40 mm

The 16 × 40 mm profile provides a narrow front strip and deep projection.

It is suitable for frequent vertical layouts when a pronounced relief is needed on the wall without a wide front surface.

With side lighting, the shadow becomes noticeable, so the distance between the slats especially affects the result.

This profile requires careful calculation of the pitch and checking the passage near the wall.

How to choose RK-002 22 × 60 mm

The size 22 × 60 mm creates a deeper and larger vertical line.

It is suitable for a high wall, ceiling, TV area, and decorative zoning.

Greater depth enhances the shadow but also protrudes more into the room.

Before ordering, you need to check that the profile does not interfere with furniture, curtains, doors, and people's movement.

How to choose square RK-002 40 × 40 mm

The square profile looks the most solid and architectural.

It is suitable for a rare large rhythm, ceiling inserts, and decorative spatial partitions.

A face width of 40 mm and a depth of 40 mm create a balanced volume that is noticeable from different angles.

This profile is especially important to evaluate with a sample, because its scale is often underestimated in photographs.

Thin or voluminous layout

A thin layout is built on line and frequency. RK-001 with a thickness of 5–10 mm is suitable for it.

A voluminous system is built on light and shadow. For it, choose large RK-001 with a depth of 23 mm or RK-002.

The deeper the profile, the more the result depends on side lighting and viewing angle.

The buyer must decide whether they need a graphic pattern on a plane or a real spatial structure.

Which slats are suitable for a small room

In a small room, the main risk is overloading the wall with the depth and frequency of elements.

Thin RK-001 15 × 5, 24 × 5, or 40 × 5 mm allow you to create geometry without a strong protrusion.

RK-002 is possible in one small accent zone, but its depth needs to be checked with a paper mockup and a real sample.

The closer a person is to the wall, the larger the profile appears.

Which profile to choose for a large wall

On a large wall, a thin slat can get lost, especially with a sparse spacing.

Wide RK-001 70 × 7, 90 × 10, 60 × 23 or 80 × 23 mm maintain readability and allow depth control.

RK-002 is suitable if the wall should have a pronounced volume and deep shadows.

The choice depends on the viewing distance: the larger it is, the larger the profile or denser the layout should be.

RK-001 or RK-002 for the ceiling

For the ceiling, the length, system weight, mounting, and light direction are important.

RK-001 is suitable for thin strips, frames, and areas where a length of 2400 mm is sufficient.

RK-002 with a length of 2750 mm is more convenient for long ceiling inserts and large rhythms, while the embedded part helps organize repeatable installation.

Specific fasteners are selected based on the base and project; there is no universal scheme for any ceiling.

Which slats are suitable for furniture and facades

For furniture facades, RK-001 is often chosen: it has thin sections and can be used as a decorative strip, frame, or repeating band.

RK-002 is too deep for most doors and may interfere with opening, adjacent facades, and handles.

Large RK-001 60 × 23 and 80 × 23 mm are only suitable for furniture of corresponding scale.

Before installation, check hinges, gaps, handles, and the position of the slat on the open facade.

RK-001 for bed headboard

A thin or medium slat helps design the headboard without significant protrusion into the passage.

24 × 5 and 40 × 5 mm are suitable for frequent layouts, while 70 × 7 or 90 × 10 mm are for calmer wide bands.

The material is tied to furniture: beech is painted in the color of the wall or bed, oak is tinted to match the floor and cabinets.

The height and width of the panel are determined by the entire bed group, not just the mattress.

RK-002 for the TV zone

A deep profile helps create a noticeable backdrop around the TV and conceal the feeling of an empty wall.

The size 16 × 40 mm is suitable for a more frequent system, 22 × 60 or 40 × 40 mm for a large architectural rhythm.

The slats should not interfere with ventilation, the bracket, cables, and service access.

First, design the equipment, then the layout and embedded parts.

Slats for the hallway

In the hallway, it is important to maintain the passage and account for cabinets, doors, switches, and hooks.

Thin RK-001 is suitable for decorative panels, furniture, and frames. RK-002 creates a stronger relief but protrudes deeper.

Using a rail as a base for a hanger requires a separate calculation of the load-bearing scheme and is not the main purpose of this article.

For the scenario with hooks, you can separately study a full comparison of RK-001 and RK-002 for a wall-mounted hanger.

Rails for the living room

In the living room, RK-001 is suitable for the wall behind the sofa, console, furniture facades, and decorative frames.

RK-002 works better on the TV zone, high wall, and zoning insert between functional areas.

Oak solid wood and veneer create a natural background, MDF under enamel allows you to match the wall color.

Lights are placed so that the relief does not create unwanted sharp shadows on the screen or furniture.

Rails for the bedroom

In the bedroom, a calm rhythm and soft chiaroscuro are usually needed.

Thin RK-001 slats are suitable for the headboard, cabinet doors, and a small panel near the vanity table.

RK-002 can be used on one wall or a ceiling insert if the volume does not make the room feel cramped.

The color is chosen together with the textiles, bed, baseboard, and doors.

Slats for the kitchen

In the kitchen, RK-001 is suitable for furniture fronts and the wall of the dining area.

RK-002 is best placed on a free decorative surface, away from areas of direct soiling and constant contact.

The finishing system must meet care requirements, but specific durability cannot be guaranteed without data on the coating.

The slats should not interfere with opening cabinets, the range hood, outlets, or kitchen equipment.

Slats for the study

In the study, oak RK-001 can connect the slats with the library, desk, and wall panels.

RK-002 with oak veneer suits a large wall and creates a more pronounced vertical structure.

MDF under dark enamel forms a graphic modern background.

Placement is checked relative to work lighting, monitor, and acoustic reflections, without attributing unconfirmed acoustic properties to the slats.

Slats for a children's room

In a children's room, it is better to avoid random protrusions in the active movement area.

Thin RK-001 suits furniture facades and a wall outside the play area.

Deep RK-002 is possible as a decorative panel with secure fastening and safe placement.

Finishing and maintenance are chosen according to room conditions, and all edges and connections are checked after installation.

Slats for a commercial interior

In a salon, store, restaurant, or hotel, slats are viewed from a greater distance.

RK-002 better preserves scale on a large wall and helps create a repeating system.

RK-001 is suitable for furniture, display cases, and detailed layouts.

Before serial ordering, one control section is assembled and the profile, pitch, color, joints, and installation are approved.

Decorative zoning

Slats can mark the boundary between the living room and dining room, entry area and hall, study and common room.

RK-002, due to its depth and length, is better suited for a standalone vertical structure.

RK-001 can be used for a light flat layout on an existing partition or furniture.

If the slats form a separate structure from floor to ceiling, installation and stability are designed separately.

How to use slats around a mirror

RK-001 15 × 5, 24 × 5, and 40 × 5 mm is suitable for a thin decorative frame and repeating stripes.

Wide sections create a more massive frame but require sufficient space around the mirror.

RK-002 can work as a large background, not as a thin frame.

The mirror must have its own secure mounting; the slats do not automatically support its weight.

How to use slats on a door

Thin RK-001 can frame a large door leaf if it does not interfere with the trim, handle, and opening.

RK-002 is usually too deep for a cabinet door and requires a special design.

Before gluing, check the weight of the decor, the door material, and the gaps to the frame.

The slats must not touch the adjacent wall or furniture when fully opened.

Individual slats or a ready-made panel

RK-001 and RK-002 are sold as individual profiles. The buyer determines the spacing, background, direction, edge margins, and placement of each piece.

A ready-made slat panel assembles the slats on a common base and reduces the number of marking operations.

Individual slats offer more freedom but require a precise design and greater installation control.

If you need a ready-made system, it's worth buying ready-made slat panels and comparing them with individual layout.

When it's more advantageous to choose PAN-001

PAN-001 is suitable for a wall where a ready-made panel on a common base is required, rather than individual installation of each slat.

This solution is more convenient for a large surface and can simplify pattern repeatability.

RK-001 and RK-002 remain preferable if you need a custom pitch, separate background, furniture decor, or non-standard geometry.

For a ready-made format, you can buy a ready-made slat panel PAN-001 and check its dimensions and construction in the card.

Why you cannot call RK-002 a massive oak batten

In its wooden version, RK-002 consists of MDF and oak veneer.

The veneer provides a natural outer texture, but the base remains MDF.

This is important for honest material selection, edge treatment, and customer expectations.

If solid oak throughout the cross-section is needed, choose RK-001 made of solid wood.

Why RK-001 does not replace RK-002 just by increasing thickness

The largest RK-001 have a depth of 23 mm, while RK-002 creates profiles with a depth of 40 or 60 mm.

Additionally, RK-002 is mounted using a hidden bracket and creates a systematic interior rhythm.

Buying a thick RK-001 does not automatically replicate the construction and installation of RK-002.

You need to compare the entire node, not just one cross-section number.

How to calculate the number of battens

First, determine the width of the area being designed and the direction of installation.

Then, choose the face width of the batten and the gap between adjacent elements.

The quantity is calculated using the 'batten plus gap' module, after which the edge fields are checked.

The formula gives a preliminary result; the final calculation is done based on the drawing of the entire wall.

How to choose spacing between slats

A small step creates a dense surface and reinforces the material.

A large step leaves more background and makes each batten independent.

For the thin RK-001, a frequent rhythm usually looks more natural; for the large RK-002, too frequent installation can overload the wall.

The step is checked with a full-size mockup of at least three to five battens.

How to calculate the edge fields

After distributing the slats, check the distance from the first and last part to the panel edges.

Uneven random fields immediately show a layout error.

Sometimes the edge gaps are made larger than the internal ones, but this should be part of the project.

If the calculation doesn't add up, adjust the spacing rather than trimming the edge slats in width.

How to calculate vertical layout

Vertical slats visually elongate the wall and require precise control of the top and bottom boundaries.

For RK-001 with a length of 2400 mm, check if the finished vertical fits without a joint.

RK-002 with a length of 2750 mm provides more freedom on a high wall.

Baseboard, cornice, suspended ceiling, and floor unevenness are considered before ordering.

How to calculate horizontal layout

Horizontal slats extend the wall and may require multiple planks in length.

Joints are placed according to a pre-selected pattern and are not left randomly in the center.

For oak, it is important to match the texture and shade of adjacent parts.

A cutting map helps to use leftovers and reduce the number of direct connections.

How to calculate a ceiling insert

On the ceiling, each line, corners, and junctions with lights are calculated separately.

A length of 2750 mm may reduce the number of RK-002 joints, but does not eliminate trimming.

Embedded parts and fasteners must be calculated for the ceiling material.

First, the lighting and ventilation scheme is approved, then the slats are placed.

How to calculate slats for furniture

On the facade, not only the number of strips is counted, but also free zones for handles, hinges, and gaps.

Thin RK-001 allow for frequent geometry without significantly increasing the door thickness.

Each slat must fit entirely on the facade and not extend into the opening area.

Before mass cutting, one control facade is assembled.

How to account for trimming allowance

The allowance depends on the number of corners, joints, base quality, and the installer's experience.

For a simple vertical wall, it is smaller than for a ceiling, furniture, or complex geometry.

You cannot assign a single universal percentage without a cutting map.

First, distribute parts across planks, then determine the reserve.

How to reduce waste

Long solid parts are placed in the cutting map first.

Short remnants are used for furniture inserts, horizontals, and test samples.

RK-001 and RK-002 are counted separately due to different lengths and cross-sections.

Remnants are kept until the completion of installation and finishing.

How to check the scale with a sample

The short sample is placed against the wall along with the intended gap.

For RK-002, it is important to see not only the face width but also the shadow depth.

For RK-001, several cross-sections are compared side by side to understand where the thin line starts to get lost.

Before a large order, it is useful to check the cross-sections of the slats in person.

How the mounting bracket RK-002 works

The 20 × 8 mm bracket is part of the RK-002 structure and defines the installation principle.

First, the brackets are placed on the base according to the project layout, then the interior rails are fixed to them.

This assembly helps to repeat the position of parts and maintain the deep volume of the profile.

The precise fastening of the bracket to the wall or ceiling is chosen based on the base and project conditions.

Can RK-002 be installed without a bracket

The card provides for installation through a bracket, so abandoning it cannot be considered a standard solution.

Another method may change the fit, geometry, and serviceability.

If the project requires non-standard fastening, it is agreed upon before ordering.

The buyer should not replace the standard system with random glue just to speed up the work.

How to install RK-001

RK-001 does not have a built-in mounting bracket, so the fixing method is chosen based on the cross-section, base, and purpose.

A thin furniture batten and a massive profile on the wall require different techniques.

Glue, mechanical fastening, or a combined scheme must be compatible with the wood and the surface.

For the kit, you can buy glue for wooden battens after checking the specific base.

How to prepare the wall

The base must be dry, strong, clean, and sufficiently level.

A thin RK-001 follows a noticeable wall wave, while a deep RK-002 can create gaps at the bracket.

Before marking, remove weak coatings and check the geometry with a long straightedge.

Serious defects are corrected before the final calculation of length and quantity.

How to mark up the wall

First, mark the general boundaries of the panel and the central axis.

Then, transfer the position of each batten and the edge margins.

For RK-002, mark the embedded parts separately so that the profile ends up at the design point.

Check the markings from the main viewpoint, not just by level.

How to install the first control batten

Place the first piece in the least risky but well-checkable position.

After fixing, check the verticality, offsets, depth, and quality of the joint.

If the result differs from the layout, adjust the scheme before installing the entire wall.

The control batten becomes the reference for the remaining elements.

How to maintain equal spacing

For repeatability, use a spacer template of the required width.

Place the spacer between adjacent slats without relying on individual measurement of each position.

On a long wall, periodically check the accumulated offset relative to the overall axis.

An error of one millimeter at each step can become noticeable at the edge of the panel.

How to finish internal and external corners

A corner cannot be solved by simply extending the standard spacing.

It is necessary to determine whether the slat ends before the boundary, wraps around the corner, or meets a separate plane.

For deep RK-002, the external corner is especially noticeable and requires a separate joint.

The corner scheme is approved on a drawing or control mockup.

How to join slats lengthwise

If one plank is not enough, the joint is placed in a less visible area or aligned with a horizontal line.

Oak RK-001 and veneered RK-002 are matched by shade and pattern direction.

On painted MDF, the joint can be prepared for a uniform finish, but geometric precision is still mandatory.

A random joint in the center of the wall disrupts the continuity of the vertical line.

How to work near sockets and switches

Electrical points are marked on the layout before calculating the spacing.

The slat should not partially cover the frame or hinder removal of the mechanism.

Sometimes the spacing is adjusted so that the socket falls into a free gap.

Relocation of electrical points is agreed upon before wall finishing, not after delivery of slats.

How to work near baseboards and cornices

The lower and upper boundaries determine the actual length of the batten.

RK-001 and RK-002 can start above the baseboard, reach the cornice, or adjoin a separate decorative strip.

A random gap at the top or bottom looks like an installation error.

All profiles are compared by depth, color, and junction line.

How to paint beech RK-001

Beech is prepared for enamel and is suitable for opaque finishes.

A test coat shows the shade, gloss, and preservation of precise edges.

All battens on one wall are painted using the same technique and in the same batch.

A thick layer should not smooth out the profile or create drips on the ends.

How to tint oak RK-001

Oak is chosen for its natural texture, so tinting should preserve the grain.

A sample is made on the same material and evaluated under real lighting.

Different planks are laid out side by side before finishing to distribute natural variations across the wall.

After installation, a color sample is kept for future repairs.

How to paint MDF RK-002

The MDF version suits solid enamel and allows the slats to become an extension of the wall color.

Primer, undercoat, and finish are chosen as a single compatible system.

The deep profile must be painted evenly on all visible sides.

A test area shows how color and shadow change the perception of the profile.

How to finish RK-002 with oak veneer

Oak veneer preserves the natural surface but does not turn the base into solid wood.

Transparent or tinted finish must be compatible with the veneer and not hide its grain.

Thin outer layers require careful handling without aggressive sanding.

Joints and edges are planned in advance, as the structure is most visible there.

Paint before or after installation

Pre-finishing is convenient for treating all sides and complex profiles.

Post-installation finishing helps unify joints and fastening points, especially on painted MDF.

For natural oak, it is often more important to avoid contaminating the already prepared surface on site.

The work sequence is chosen before cutting and tested on a control strip.

How to care for slats

Dust is removed with a soft cloth, brush, or suitable attachment.

The deep RK-002 collects more dust on side surfaces than the flat RK-001.

Care products are chosen based on the finish coating, not just the base material.

Abrasives and excess moisture can damage paint, tint, or veneer.

Mistake: choosing a slat based only on a photo

In the catalog image, the thin RK-001 and deep RK-002 may look comparable because the scale is not obvious.

The actual profile should be evaluated by cross-section, length, and sample.

It is especially easy to underestimate the 60 mm depth of RK-002 and the 90 mm width of RK-001.

Before ordering, make a full-size mockup with several slats and the actual gap.

Mistake: calling veneer solid wood

RK-002 with oak veneer has a natural oak surface, but its base is MDF.

A customer who needs solid wood throughout the cross-section should choose the oak RK-001.

The incorrect expectation is especially critical for open ends and transparent finishes.

The material is checked in the specific modification's card.

Error: considering a length of 2750 mm sufficient without measuring

The nominal ceiling height does not equal the finished length of the part.

Baseboard, cornice, floor unevenness, suspended ceiling, and installation gap change the size.

Even RK-002 may require trimming or be too short for a non-standard tall room.

The order is made according to a working drawing, not the apartment's passport.

Error: buying RK-001 for a deep wall

A thin slat won't create the same shadow as a profile with a depth of 40–60 mm.

Increasing the pitch does not compensate for the lack of volume.

If the task relies on strong chiaroscuro, you need to compare large RK-001 with RK-002, rather than choosing the thinnest option.

The sample immediately shows the difference under side lighting.

Mistake: installing RK-002 on furniture without checking

A deep profile can interfere with opening, handles, adjacent facades, and passage.

RK-002 was primarily created as an interior system for walls, ceilings, and zoning.

For furniture, RK-001 with thin sections is usually more practical.

Non-standard application requires a separate project and a control facade.

Mistake: not accounting for the RK-002 embedded element

The customer sometimes only counts the visible rail and forgets about the mounting system.

Without a mortgage, the fit and installation technology change.

The quantity, length, and fastening of mortgages are included in the specification along with the main profiles.

Before payment, check how the selected option is configured and what needs to be ordered separately.

Error: calculating quantity only by area

The wall area does not show the number of verticals, the length of each part, and the edge fields.

The width of the area, the face width of the rail, the gap, and the direction are needed.

For the ceiling and horizontal layout, joints along the length are added.

The exact calculation is based on the layout and cutting map.

Error: choosing too frequent a step

Frequent installation of large RK-002 can turn a wall into a heavy, dark structure.

In a small room, this visually reduces the space.

For thin RK-001, a frequent step is more appropriate, but also requires a free background.

A layout of several slats helps assess density before purchasing the entire volume.

Mistake: choosing too sparse a step

A sparse layout of thin RK-001 can look like random stripes rather than a single panel.

Wide RK-001 and square RK-002 better tolerate a large gap.

The step should be

Who RK-001 is suitable for

RK-001 is suitable for a furniture maker, designer, and interior owner who needs real solid wood and precise section selection.

It is especially useful for furniture, frames, small panels, fine graphics, and oak tinting.

Seven sizes allow the profile to be adapted to the room and the object.

The model may not suit a tall wall if the 2400 mm length is insufficient and a continuous vertical is required.

Who is RK-002 suitable for

RK-002 is suitable for a project with a tall wall, ceiling, large TV area, and pronounced volume.

MDF under enamel is useful for a monochrome architectural layout, oak veneer for a natural surface on a stable base.

The mounting insert helps build a systematic repeating rhythm.

The model may be excessive for a small facade, narrow passage, and delicate frame.

When it is better to choose a ready-made panel

A ready-made panel is suitable when the buyer values speed and repeatability more than an individual step.

It reduces the number of individual operations and combines slats on a common base.

Piece RK-001 and RK-002 are better for non-standard patterns, furniture, corners, and separate zones.

It is useful to compare before deciding individual slats or a ready-made panel.

When to avoid both models

If a certified acoustic panel is required, RK-001 or RK-002 cannot be attributed special properties without data.

For exterior facades, wet areas, or load-bearing partitions, separate certified solutions are needed.

If the partition is too narrow or the profile obstructs passage, a different finishing format is chosen.

An honest rejection of an unsuitable slat protects the budget and interior from rework.

How to buy slats at STAVROS

First, determine the material, length, cross-section, and type of relief.

Then open the RK-001 or RK-002 card, check the current options, and calculate the quantity according to the drawing.

After that, add samples, installation materials, and finishing materials.

For a general comparison, you can buy wooden slats browse through the category and view all sizes.

Practical comparison of RK-001 and RK-002

How to choose between solid wood and a stable base

RK-001 solid wood is valued for its naturalness throughout the cross-section and the ability to use the wood in furniture and exposed parts.

The MDF base of RK-002 is convenient where repeatability of large profiles and subsequent painting are important.

Oak veneer provides a natural surface without turning the base into solid wood.

The decision is made based on the design and finish, not on the simplified rule "wood is always better."

How to compare price and lifespan without making a wrong conclusion

The price of one slat does not show the cost of the entire wall.

The final cost is affected by the number of slats, length, waste, mounting blocks, installation, finishing, and possible joints.

A thin RK-001 may require more elements with a frequent pitch, while a large RK-002 may require fewer, but with a more complex system.

It is useful to study the material separately RK-001 or RK-002 — what to pay for and then calculate a specific project.

How to connect slats with lighting

Side light enhances shadows and makes deep RK-002 more noticeable.

Front diffused lighting softens the relief and suits thin RK-001.

Luminaires should not interfere with mounting or cause overheating.

The electrical plan is approved before marking the slats.

How to connect slats with furniture

Slats can repeat the width of facades, support cabinet axes, and unify the wall with furniture.

RK-001 is easier to use directly on and near objects.

RK-002 works better as a background or a separate architectural plane.

Space is left between the protruding profile and the furniture for opening and cleaning.

How to connect slats with doorways

Vertical layout can support the height of the door and the casing.

Thin RK-001 fits narrow piers, large RK-002 requires more free space.

Slats should not interfere with the door leaf and handle when fully opened.

The edge offsets are checked relative to the casing, not just the wall corner.

How to check the finished area after installation

Check verticals, horizontals, equal spacing, and edge fields.

Inspect joints, ends, embedded parts, and attachment points.

Evaluate the wall under daylight and artificial light from the main viewing point.

After acceptance, save the layout, article number, cross-section, and finish sample.

What to buy together with RK-001 and RK-002

How to choose wall slats to match the interior color

If the slats should blend with the wall, choose beech RK-001 for enamel or MDF RK-002 for painting.

Thin RK-001 shows a soft line, deep RK-002 creates a strong shadow even with the same color.

A test paint sample is done next to the finished wall, not just from the catalog.

The gloss level is coordinated with the base so the slats don't accidentally appear more glossy.

How to choose slats for natural oak

Oak RK-001 is needed when the solid wood must be visible across the entire part.

RK-002 with oak veneer is suitable for a large wall where a natural surface and stable MDF base are important.

Both options require a real sample: solid wood and veneer may differ in pattern and shade.

Mixing on the same plane is only allowed after a test layout.

How to choose slats for renovating a finished room

In a finished renovation, first check the walls, baseboard, cornice, sockets, and the route for bringing in long planks.

RK-001 is easier to use in a small area or on furniture without major alterations.

RK-002 requires space for the mounting frame and more precise base preparation.

Before purchasing, mark the full panel outline with painter's tape and check for protrusions in the passage.

How to choose battens for a new project

In the new interior, the layout can be coordinated with electrical, furniture, and lighting before finishing.

RK-002 particularly benefits from early planning of embedded parts and finished height.

RK-001 can be conveniently integrated simultaneously into furniture facades, wall frames, and other wooden details.

The specification must include article number, material, cross-section, length, quantity, finish, and mounting assembly.

How to organize serial installation

For several identical walls, first assemble one control sample.

On it, approve the spacing, edge margins, color, ends, and fastening quality.

After approval, produce templates and mark parts by rooms.

This approach reduces discrepancies between crews and batches.

How to store slats before installation

Slats are stored horizontally on a level support in a dry room.

Lengths of 2400 and 2750 mm require support across the entire surface to prevent point pressure on the parts.

Veneered and finished elements are protected from friction.

Slats of different cross-sections and rooms are not mixed after cutting.

How to transport long slats

Before ordering, check the car, elevator, stairs, doorways, and turns.

RK-002 with a length of 2750 mm requires more space for maneuvering.

Slats must not be bent excessively or carried by one end.

Ends and face surfaces are protected until unpacking at the site.

How to accept goods upon delivery

They check the article, material, cross-section, length, and quantity.

Check the surface, profile, ends, and the presence of the provided embedded part for RK-002.

All issues are resolved before cutting, painting, and installation.

The finish sample is compared with actual slats before processing the entire batch.

Final check before payment

Determine whether you need solid wood or MDF with veneer, a thin line or deep volume.

Check the length of 2400 or 2750 mm against the finished size of the area.

Calculate the quantity based on the slat width, pitch, and edge fields.

Add samples, installation materials, embedded parts, and allowance according to the cutting map.

How to check slats on the scale of the entire wall

A short sample shows the material but does not convey the final pattern. Before ordering, you should draw or mark at least five adjacent slats with the actual spacing.

On a large wall, it is also useful to mark the edge fields, the height of furniture, TV, doors, and lights. This makes it clear where the decorative zone ends and whether it looks accidentally cut off.

RK-001 is primarily evaluated by strip width and frequency. RK-002 is evaluated by depth, shadow, and projection into the room.

The layout photo is viewed from the main entry point and from the seating area. Sometimes a profile that looks good up close gets lost from a few meters away.

How to choose the layout direction

Vertical slats emphasize height and help organize the wall into a neat system. Horizontal slats visually widen the surface but often require joints along the length.

Diagonal or combined layout is only possible after an accurate drawing: it increases waste, the number of corners, and requirements for matching cross-sections.

RK-001 is easier to use in complex graphics due to its thin options. RK-002 is better revealed in a calm vertical or ceiling rhythm.

The direction is chosen before calculating the quantity, because the length of 2400 and 2750 mm works differently on vertical and horizontal surfaces.

How to distribute different cross-sections in one project

Multiple sections can be used as a hierarchy: a wide profile sets the main axes, a thin one sets the secondary lines.

But the random alternation of seven RK-001 variants turns the wall into a set of samples. For one area, one or two sizes are usually enough.

The combination of RK-001 and RK-002 is justified when the models are separated by function: for example, an array on furniture and a volumetric veneered system on the wall.

Before purchasing, a specification is compiled for each room so that installers do not confuse the profiles and pitch.

How to estimate the final cost of the project

First, the number of slats and embedded parts is calculated, then trimming, finishing, fasteners, and labor are added.

A narrower profile does not always mean a lower wall cost: with a frequent pitch, more planks and more installation operations will be required.

RK-002 may require fewer verticals, but includes a mounting system and deeper processing of ends and junctions.

You need to compare two complete specifications, not the price of one RK-001 plank and one RK-002 plank.

How to preserve the possibility of future repairs

After installation, one short slat, a sample of the finish, the article number, the section, and the layout diagram are kept.

For RK-002, it is useful to keep information about the mounting bracket and fastening method. For oak RK-001, a tinting recipe.

If a separate part is damaged, this data will help manufacture a replacement without completely disassembling the wall.

Spare material is stored horizontally and protected from moisture, light, and accidental damage.

How to choose a profile based on viewing distance

The distance to the wall changes perception more than it seems. In a narrow corridor, a person sees the slat almost up close, so even a 16 × 40 mm profile can appear very deep. In a spacious living room, a thin RK-001 15 × 5 mm, on the contrary, may get lost if viewed from several meters away.

For close viewing, thin and medium RK-001 sections work better, especially with a frequent pitch. For a large wall, hall, or commercial space, wide RK-001 and voluminous RK-002 are suitable. You need to check not a single part, but a group of several slats with a real gap.

Such a mockup helps to see in advance how strong the shadow will be, whether the profile overloads the passage, and whether the pattern is preserved from the main viewpoint. After checking, you can more accurately select the section and calculate the quantity without excess stock.

FAQ: questions about RK-001 and RK-002

How is RK-001 different from RK-002?

RK-001 is a slat made of solid beech or oak, 2400 mm long, with seven sections. RK-002 is an interior slat made of MDF or MDF with oak veneer, 2750 mm long, with three sections and a mounting bracket.

Which model is made from solid wood?

RK-001. It is produced in beech or oak.

Is RK-002 an oak slat?

In the wood version, it has an MDF base and oak veneer. It is not solid oak throughout the cross-section.

What cross-sections are available for RK-001?

15 × 5, 24 × 5, 40 × 5, 70 × 7, 90 × 10, 60 × 23, and 80 × 23 mm.

What sizes are available for RK-002?

16 × 40, 22 × 60, and 40 × 40 mm. The embedded part has a size of 20 × 8 mm.

Which slat is longer?

RK-002: 2750 mm vs 2400 mm for RK-001.

What to choose for a ceiling height of 2700 mm?

Usually RK-002 is more convenient, but first you need to measure the finished length between the baseboard, cornice and ceiling.

Which model is suitable for enamel?

Beech RK-001 and RK-002 made of MDF. The specific painting system is tested on a sample.

What to choose for a natural oak texture?

RK-001 made of solid oak or RK-002 with oak veneer — depending on the requirements for the base and depth.

Which batten creates a deeper shadow?

RK-002 thanks to profiles with depths of 40 and 60 mm. For RK-001, the maximum depth of confirmed sections is 23 mm.

Is RK-001 suitable for furniture facades?

Yes, especially thin sections 15 × 5, 24 × 5 and 40 × 5 mm after checking gaps and opening.

Is RK-002 suitable for furniture?

Only in a specially designed project. The deep profile is more often used on walls, ceilings, and in zoning.

What is the RK-002 mounting bracket for?

It forms the intended mounting assembly and helps install the volumetric slat in the design position.

Can RK-002 be used without a mounting bracket?

A non-standard method must be approved separately. The card provides for installation via a mounting bracket.

How to calculate the spacing between slats?

Select the face width, set the gap, distribute the module across the section width, and check the edge fields.

When is it more advantageous to buy a ready-made panel?

When an individual step is not needed and a ready-made system on a common base is important.

Can RK-001 and RK-002 be combined?

Yes, in different functional zones, if the materials, color, and scale are related by the project.

Which profile is suitable for a small room?

Usually thin RK-001. Deep RK-002 is used locally after checking with a mockup.

Which profile should I choose for a large wall?

Wide RK-001 or RK-002, if a particularly deep relief is needed.

Is it necessary to order a sample?

Yes, a sample helps evaluate the cross-section, shadow, material, shade, and protrusion in the passage.

What allowance should be added?

The allowance is determined by the cutting map, number of joints, corners, and installation complexity. There is no universal percentage.

Where to buy RK-001 and RK-002?

In the corresponding STAVROS cards after selecting the material, cross-section, and calculating the quantity.

What should be checked before ordering?

Length, cross-section, material, finish, pitch, quantity, embedded element, base, fasteners, and delivery route.

Result: RK-001 or RK-002

RK-001 is chosen when you need genuine beech or oak solid wood, length 2400 mm, and a precise selection from seven cross-sections. Thin profiles suit furniture, frames, and frequent layouts; wide and deep ones suit prominent strips and large interior details. Beech is designed for enamel, oak for tinting and preserving the natural grain.

RK-002 is chosen for a high wall, ceiling, TV zone, and volumetric zoning. The 2750 mm length helps reduce the number of joints, and profiles 16 × 40, 22 × 60, and 40 × 40 mm create deep chiaroscuro. MDF can be painted, MDF with oak veneer preserves the natural surface, and installation is based on an embedded element 20 × 8 mm.

Before purchasing, you need to determine the material, depth, length, and pitch, order a sample, create a full-size mockup, and calculate each slat according to the cutting map. If individual installation is not required, it is worth comparing individual profiles with ready-made PAN panels.

On the STAVROS website, you can open the RK-001 and RK-002 cards, view the slat catalog, order samples, and select materials for installation and finishing. This route helps you buy exactly the profile that matches the wall, furniture, or ceiling, rather than a random plank with unsuitable depth and material.