A chest of drawers on four wooden legs MN-227 will stand on oiled parquet: which glides to buy together with furniture supports — sliding FUR-021 or felt FUR-027, if the chest is sometimes moved for cleaning

Parquet is more often scratched not by the wooden leg itself, but by what got between the furniture and the floor.

A grain of sand, hard construction debris, or fine abrasive trapped under the glide changes the whole meaning of "floor protection": instead of even contact, a local hard point appears, which a person drags across the surface along with the dresser. Therefore, the choice between FUR-021 and FUR-027 for MN-227 cannot be reduced to the formula "felt is softer — so it's always safer" or "SUPER GLIDE slides better — so take it."

In our scenario, the task is specific:

• the dresser stands on four MN-227 145×70×70 mm;

• the finished floor is oiled parquet;

• the furniture is not built-in;

• a few times a month or week it is slightly moved aside for cleaning;

• card MN-227 recommends two different accessories: FUR-021 and FUR-027.

FUR-021 is a round glider 19×19×5 mm from the SUPER GLIDE series. The manufacturer directly describes it as a sliding element that facilitates moving heavy structures without damaging the floor surface. FUR-027 is a felt glider: the card currently shows 25×25×5 mm, an included screw, and a soft felt working part.

If the dresser is indeed regularly moved on smooth clean parquet and the goal is to reduce effort when moving, FUR-021 seems more logical based on its stated function. If priority is soft contact, calmer and quieter movement, and the dresser is moved rarely and carefully, FUR-027 may be preferable.

But neither of them is a guarantee against scratches.

For parquet, the most important thing is four conditions:

1. the working surface of the glider is clean;

2. the floor itself in the movement area is cleaned of sand and hard crumbs;

3. the dresser is moved without jerking and without tilting on one leg;

4. the chosen FUR is pre-tested on an inconspicuous area of your specific flooring.

Price should almost not affect the choice. At the time of checking, FUR-021 costs 130 ₽, FUR-027 — 55 ₽. The difference on four legs:

4 × (130 − 55) = 300 ₽.

Against the background of the MN-227 set, this is too little to choose a floor protector "by cheapness."

Four beech MN-227 "Prestige" currently cost:

4 × 1 710 = 6 840 ₽.

Four oak ones:

4 × 2 040 = 8 160 ₽.

With FUR-021, the product set comes to 7,360 ₽ for beech and 8,680 ₽ for oak. With FUR-027 — 7,060 ₽ and 8,380 ₽ respectively.

That is, the decision should be made based on the parquet operating mode, not on the 300 ₽ difference.

When the floor, the dresser's mass, and the movement scenario are already determined, you can buy furniture legs MN-227 145×70×70 mm and immediately include one type of floor protector for all four supports in the specification.

Round thrust washer d=19 mm, FUR-021

from 1.55 $

Go to Catalog

MN-227 145×70×70 mm: what exactly is purchased for the dresser

In this article, MN-227 has no height selection. This fundamentally distinguishes the task from materials where 120/160, 450/740 mm and other dimensional variants are compared.

The current card confirms:

Watch video ...

Beech MN-227

Beech is logical for furniture under opaque painting if a uniform color of the body and legs is required.

Our factory also produces:

Wooden newel KL-049

from 52.86 $

Decor Set C-006-1-2

from 579.90 $

Wooden ceiling rosette R-022

from 185.73 $

Wooden Molding K-031

from 6.94 $

Geometric Furniture Leg MN-206

from 34.32 $

Geometric Furniture Leg MN-209

from 35.16 $

Baseboard B110V1L polystyrene HIWOOD 110mm x 16mm x 2.0m. L

from 19.13 $

Polyurethane Molding MLDPU-002

from 65.30 $

View Full Product Catalog

Oak MN-227

Oak is chosen when the natural texture should remain visible and support other oak furniture or interior details.

Geometry 145×70×70 mm

For our scenario, it is already selected by the dresser design.

But before ordering four supports, you still need to check that the top node 70×70 mm and the mounting method match the bottom structure. The floor protector solves the contact with the floor, not the top leg mounting.

"Prestige"

The card offers MN-227 as "Prestige", that is, with more thorough manual surface preparation.

This is convenient for a part that will be visible in finished furniture, but does not affect the choice of FUR-021 or FUR-027.

Why the MN-227 card is more important than the general advice about glides

Because the manufacturer himself recommends exactly two specific accessories for this leg.

The new article should not turn into a catalog of dozens of furniture glides. The buyer needs to choose from two compatible options for their parquet and operating mode.

Buy furniture legs for a dresser: why the glide is chosen simultaneously with MN-227

When a person wants buy furniture legs, it is easy to perceive the wooden support as a finished product.

For parquet, this is an incomplete specification.

Before ordering, the following must be known:

• floor type;

• the condition of the coating;

• mass and dimensions of the dresser;

• how often furniture is moved;

• how far;

• is there a carpet;

• is silence important;

• is light service access needed behind the furniture;

• what glider will be installed on each leg.

Why the floor needs to be known in advance

The same FUR behaves differently on smooth parquet, rough board, tile, and carpet.

Our article considers oiled parquet, not all surfaces at once.

Why the mass of a dresser matters

The heavier the furniture, the greater the force when moving it, and the stronger any hard particle is pressed against the floor.

This does not mean there is a universal mass after which a specific FUR is needed. The cards do not provide such a boundary.

Why the frequency of movement matters more than "softness"

If the furniture is almost never moved, the main task of the glider is calm, long-term contact.

If it is moved every week, the properties during sliding become more important.

FUR-021 for MN-227: what the card actually confirms

FUR-021 is a specific product, not an abstract "plastic heel."

According to the current card:

• size 19×19×5 mm;

• price 130 ₽;

• mounting — self-tapping screw;

• complete universal galvanized self-tapping screw 3.5×20 mm;

• SUPER GLIDE series;

• special sliding coating;

• the manufacturer directly mentions easier movement of heavy structures without damaging the floor.

You can Buy FUR-021 base plate after checking the coating and operating mode.

What is important in it for our dresser

The main advantage is low resistance to movement compared to rigid wooden contact.

If the dresser has to be moved aside a little, the person applies less effort.

Why this is useful on heavy furniture

There is less chance that the user will first sharply jerk the body, lift one side, or skew the dresser.

But this does not negate careful movement.

Why "sliding" does not equal "risk-free"

A hard particle can also fall under FUR-021.

Then the sliding coating does not eliminate the abrasive between the glider and the parquet.

Why you cannot promise absolute safety for oiled parquet

Parquet can differ in wood species, hardness, oil condition, age, and the presence of local defects.

Therefore, the production recommendation must be supplemented with a real test on site.

FUR-027 for MN-227: how a felt glider differs in operation

FUR-027 — different contact character.

The card now shows:

• name d=24 mm;

• size table 25×25×5 mm;

• price 55 ₽;

• complete universal self-tapping screw 3.5×20 mm;

• felt working part.

You can buy felt glide FUR-027.

What felt provides

A soft layer appears between the hard furniture support and the floor.

For parquet, this is intuitively appealing.

Quieter movement

A soft working surface reduces the harsh sound of contact.

This is especially noticeable if the furniture is slightly shifted rather than carried.

Why felt requires maintenance

It can collect dust, fur, and small particles.

By itself, the soft material does not remain perfectly clean for years.

Main risk

A hard grain of sand can get into the felt.

After that, the soft surface ceases to be homogeneous and gains a local abrasive.

Therefore, a felt glider is only good with regular inspection.

FUR-021 or FUR-027: comparison specifically for the MN-227 dresser

The meaning of the choice is better seen in one table.

This table does not produce a universal winner.

It shows which parameter becomes the main one in a specific room.

If the dresser is moved every week

The sliding function FUR-021 becomes a practical advantage.

A person does not need to overcome great resistance, especially if the furniture is full.

If the dresser is moved several times a year

Ease of sliding is no longer so important.

The soft felt surface FUR-027 may be more logical in terms of contact nature.

If there is sand from the street in the house

For example, an entryway nearby, children, a dog, an open terrace.

Then the main question is not the FUR type, but the discipline of cleaning under the furniture.

If the floor has just been restored and coated with oil

A local test of the selected accessory needs to be conducted.

It cannot be assumed that a fresh oiled surface automatically reacts the same way to any glider material.

The dresser is moved once a week for cleaning: operating mode matters more than material MN-227

The same beech or oak MN-227 can work completely differently in two apartments.

In the first one, the dresser was placed against the wall and hasn't been moved for five years.

In the second one, there's an outlet and cables behind it, and cleaning is done every week.

The leg material is the same.

The functional load on the foot pad is different.

Scenario 1. The dresser is almost stationary

Priorities:

• stable contact;

• floor protection;

• absence of noise with small random displacements.

Here FUR-027 looks like a natural option if the felt is kept clean.

Scenario 2. The dresser is regularly moved back 200–300 mm

Priorities:

• controlled sliding;

• minimal effort;

• absence of jerking.

FUR-021 gains an advantage in the stated function.

Scenario 3. The dresser is moved far

For example, to the middle of the room.

Even a good glider does not mean that heavy furniture should be dragged across the entire parquet.

For long-distance movement, it is safer to use proper furniture moving equipment and the help of a second person, rather than treating FUR as a transport device.

Scenario 4. Dresser empty during cleaning

The difference in force between FUR-021 and FUR-027 may feel smaller.

Scenario 5. Dresser filled with books, dishes, or textiles

Mass is higher.

The sliding function becomes more noticeable.

But the pressure on a random grain of sand is also higher.

Buying wooden furniture legs for parquet: first check the parquet itself

If the task is — Buy wooden furniture legs For furniture on parquet, you cannot treat all wooden floors as one surface.

Oiled parquet

Oil coating preserves a more natural tactile feel of the wood and usually requires periodic maintenance.

In our article, this type is specified in the initial situation.

Lacquered parquet

The finish is different.

The surface may have a different coefficient of friction and different sensitivity to local scratches.

New factory parquet

The coating is fresh, geometry is usually stable, but actual properties depend on the manufacturer.

Old restored board

May have unevenness, open pores, local areas of old and new finish.

Matte surface

Minor marks may be less noticeable in one lighting and more pronounced in side lighting.

Why the test is needed even with an expensive heel protector

Because the FUR card does not know:

• the specific breed of the floor;

• the condition of the oil;

• the age;

• humidity;

• the quality of cleaning;

• the weight of the dresser.

How to perform a heel test on oiled parquet without risk to the visible area

A section is selected that:

• is hidden by furniture;

• is located under the future dresser;

• is not the central part of the room.

Step 1. The floor is thoroughly cleaned

Not just visually.

Dust and sand need to be removed.

Step 2. The FUR work surface is also cleaned

The new glider could have been lying in packaging or on the workbench.

Step 3. Create a load

A test without load is not very informative.

But you don't need to put the whole dresser on right away if you can reproduce part of the weight with a safe mock-up.

Step 4. Make a small movement

Without a jerk.

At a short distance.

Step 5. Inspect the surface under side lighting.

The trace may be invisible from above.

Step 6. Compare the two types.

If possible, test FUR-021 and FUR-027 in the same way.

Why even a good heel pad can scratch parquet.

The key mistake is to think that the danger lies only in the FUR material.

In practice, abrasive most often comes from outside.

Sand.

Quartz particles are hard.

Fine construction debris

After renovation, it can remain for months in hard-to-reach places.

Metal shavings

Rare, but especially unpleasant.

Hard filler crumbs

Can get in during furniture repair.

Why weight worsens the problem

The higher the load on the support, the stronger the hard particle is pressed against the surface.

Why longer movement is more dangerous than shorter

The particle travels a long distance.

The trace becomes longer.

Felt FUR-027: why it needs periodic inspection

The felt is soft but porous.

This is both its advantage and its service area.

The felt collects dust

Fine dust may be harmless by itself, but it mixes with harder particles.

The fiber wears out

With repeated movement, the working surface becomes less uniform.

A grain of sand may get into it

And stay there.

This is more dangerous than a particle that simply lies on a smooth surface and can fall out.

What to do

Periodically:

1. lift one corner of the furniture in a safe way;

2. inspect the FUR;

3. remove debris;

4. assess wear;

5. replace the element if the surface is damaged.

Why replacing cheap hardware is more cost-effective than repairing parquet

Four FUR-027 cost 220 ₽ at the time of checking.

Even several replacements over years of use are usually incomparable to restoring a visible section of a wooden floor.

Sliding FUR-021: when the ability to move a dresser is a real advantage

Cleaning

You can access dust behind furniture without a heavy pull.

Socket

A dresser sometimes covers an electrical outlet.

Cables

Behind it there may be a router, lighting, or appliances.

Rearrangement

In a rental apartment, furniture often changes position.

Wall service

Need to touch up a section or check the baseboard.

Why easy initial movement matters

People more often damage furniture and the floor at the moment of the first jerk.

If the support starts moving more smoothly, it's easier to control the body.

When sliding is too easy, on the contrary, it's undesirable

Ease of movement is not an absolute advantage.

A dresser with drawers receives horizontal forces every time a drawer is opened.

If the furniture is very light, the floor is smooth, and the contact system is slippery, the body can shift.

It cannot be claimed that FUR-021 will necessarily cause such behavior. This depends on:

• masses;

• center of gravity;

• the slides;

• opening force;

• floor.

But this risk needs to be checked.

How to check

Place the ready empty dresser.

Open the stiffest drawer.

Then repeat with normal loading.

The body should not unexpectedly move away.

Opening multiple drawers: the foot does not replace furniture stability

It is necessary to clearly separate three tasks.

First: protection of the parquet floor.

Second: the nature of furniture movement.

Third: protection against tipping over.

FUR-021 and FUR-027 relate primarily to the first two.

They do not replace:

• correct body geometry;

• sufficient support base;

• anti-tipping measures;

• wall anchoring, if required by the design.

Why this is especially important for a tall dresser

When opening the top drawers, the center of gravity shifts.

The foot should not be perceived as a "stability system."

Four MN-227: why one type of FUR is better on one dresser

Random scheme:

• two FUR-021 in front;

• two FUR-027 in the back

seems like a compromise.

In practice, it creates different contact conditions.

What changes

• resistance to movement;

• wear;

• sound;

• reaction when turning the body.

When a mixed scheme may be acceptable

Only if it is specially designed and has a clear function.

For a regular dresser, it is more reasonable to use a single type on all four supports.

How many FUR-021 or FUR-027 to buy together with four MN-227

Basic working set for a four-leg dresser:

4 legs → 4 glides.

But the amount of spare parts is better decided separately.

When to buy exactly four

if:

• object nearby;

• hardware easily accessible;

• furniture used at home;

• replacement does not create a logistical problem.

When to add one spare

If you want to have a quick repair element at home.

When to add two

If the dresser will be actively moved and the owner is ready to periodically maintain FUR.

Why a spare of glides is not the same as a spare of legs

One MN-227 costs 1,710–2,040 ₽.

One FUR — 55–130 RUB.

Storing a supply of small wear parts is economically much more logical than buying a fifth wooden leg without a reason.

Price of the MN-227 set + support pads

According to the cards at the time of check:

Beech + FUR-021

4 × 1 710 + 4 × 130

= 7 360 ₽.

Beech + FUR-027

4 × 1 710 + 4 × 55

= 7 060 ₽.

Oak + FUR-021

4 × 2 040 + 4 × 130

= 8 680 ₽.

Oak + FUR-027

4 × 2 040 + 4 × 55

= 8 380 ₽.

Difference between FUR types on the same dresser:

300 ₽.

Why choosing by price is irrational

Because even minor repairs to oiled parquet can potentially cost more than this difference.

The floor protector must match the operating conditions.

Beech or oak MN-227: does the wood species affect the choice of floor protector

Almost not, based on the logic of contact with the floor.

Beech

They choose based on design and finish.

Oak

Same.

Contact with the floor still happens through FUR

If a heel pad is installed, it is the lower working surface.

What actually changes with the wood species

• appearance;

• finish;

• price;

• combination with the body.

What does not change

Does not turn FUR-021 into FUR-027 and vice versa.

Therefore, the selection scheme is:

leg material — according to the furniture; FUR — according to the floor and usage.

Buy legs for a dresser, wardrobe, and nightstand: when MN-227 is worth comparing with other supports

If MN-227 appeals to you in terms of design, that doesn't mean it has to fit every dresser.

Can be opened buy legs for a dresser, wardrobe, and nightstand and compare other models.

Different height

MN-227 has 145 mm.

If the dresser needs 100 or 200 mm, it's better to choose a different support than to change the body for one model.

Adjustment

If the floor is noticeably uneven, FUR-021/FUR-027 do not solve this problem.

Different style

The geometric MN-227 doesn't suit every facade.

The 70×70 platform doesn't match the furniture

Then a different mounting bracket or a different leg is needed.

Why FUR-021/FUR-027 cannot be used to compensate for an uneven floor

Both of the feet in question are fixed elements.

They are not adjustable feet.

If one leg is "shorter" due to a floor height difference, you cannot:

• place a random second felt underneath;

• put a different FUR on one corner;

• create different heights without a project.

For leveling, a different type of solution is needed.

If such a task arises, you can open Furniture leg hardwarebut not turn this article into a review of all regulated systems.

What happens if the FUR on one corner has worn out more

The furniture may start to wobble.

Reasons

• more often pulled by one edge;

• the floor is uneven;

• more dirt under one foot;

• one leg receives a different load.

What to do

Check the entire set.

Do not blindly replace only one element if the others are already heavily worn.

How to check the selected thrust bearing before final use

Test on an inconspicuous area

Under the future dresser.

Clean floor

Absolutely.

Clean work surface

And FUR too.

Slight movement

Without a jerk.

Inspection

Under side lighting.

Retest after load

Sometimes the mark only appears under real weight.

Oil parquet: why floor care and FUR work as one system

A floor protector does not exist separately from cleaning.

If the owner regularly:

• vacuums;

• removes sand;

• controls the felt;

• does not drag furniture through a dirty area,

the risk is lower.

If abrasive accumulates under the dresser for years, any contact becomes worse.

How often to inspect FUR-027

There is no universal calendar interval.

The period depends on:

• frequency of movement;

• dust;

• animals;

• proximity to the entry zone.

Practical logic

Inspect every time the dresser is already pulled out for deep cleaning.

This way, no separate procedure is required.

How often to inspect FUR-021

By the same logic.

Especially after moving through an area where sand might have been.

When FUR-021 looks like a more rational choice for MN-227

Scenario:

• the dresser is heavy;

• it is moved regularly;

• the floor is smooth;

• the owner keeps it clean;

• it is important not to pull the furniture with a jerk.

Then the sliding function matches the task.

When FUR-027 looks more rational

Scenario:

• the dresser mostly stands still;

• movements are short and rare;

• quiet and soft contact is important;

• the owner is ready to inspect the felt.

When none can be chosen without additional consultation

if:

• parquet is very valuable or historical;

• the coating is fresh and the floor manufacturer has given special restrictions;

• the dresser is extremely heavy;

• the surface has a non-standard oil;

• furniture will move often and far.

Then it is worth considering the recommendations of the coating manufacturer.

Carpet under the dresser: does the choice change

If the legs partially stand on the carpet and partially on the parquet, the case becomes more complicated.

One cannot assume that a single FUR works the same on two surfaces.

Possible problem

Front legs on the carpet, rear legs on the parquet.

The dresser has different resistance to movement.

What to do

Design a unified base or change the furniture placement.

Thin carpet over parquet

Felt may catch differently.

SUPER GLIDE may also work differently.

Need a test again.

The dresser stands against the wall and only moves back and forth.

This is simpler than turning.

Why

Each leg follows almost the same trajectory.

How to prepare the area

Clear the movement paths before moving.

The dresser is turned around.

The legs start moving along an arc.

The risk of catching a random particle is higher.

Why pulling the dresser by one side is worse

The body twists, and the two legs receive different loads.

It is better to move it in a controlled manner.

Is it necessary to unload the dresser before moving it?

For heavy contents, it is reasonable.

This reduces the load on the FUR and the floor.

The article does not specify a specific weight at which unloading is mandatory.

What to do with the drawers

Close and secure them so they do not slide out during movement.

Why a glider with a self-tapping screw is more convenient than random self-adhesive for such a case

Both FURs from card MN-227 have mechanical fastening.

This makes the position of the element more predictable.

But the screw also needs to be mounted into a suitable part of the wooden leg.

FUR center relative to the leg

There is no need to place the foot pad by eye.

On the bottom plane of 70×70 mm, the position should be marked according to the project.

Why

A shifted element changes the nature of contact and the appearance.

Can FUR-027 be installed on 70×70 mm

With dimensions of 25×25, it is significantly smaller than the bottom area.

But the exact mounting location and the admissibility of fastening need to be determined based on the actual leg.

Can FUR-021 be installed

19×19 mm is also compact.

The MN-227 card recommends it, which is the basis for including it in the set.

Why the size of the support pad is not equal to the contact area of the leg

A wooden leg 70×70 does not have to contact with its full area after installing FUR.

The load is transferred through the accessory.

This is another reason not to experiment with unintended hardware.

FUR-021 vs FUR-027 on oiled parquet: a decision tree without general phrases

For this pair of accessories, it is convenient not to look for a "winner," but to proceed from the specific operating mode.

Question 1. Is the dresser moved more often than once a month?

If yes, switch to FUR-021 as the main candidate and separately test it on your parquet.

If not, FUR-027 remains a strong option due to its soft contact.

Question 2. Is the dresser heavy in working condition?

If yes, ease of initial movement becomes more important. The smaller the jerk, the easier it is to control the furniture.

If not, the difference between the two FUR types in terms of force may be less noticeable.

Question 3. Does sand regularly appear in the house?

If yes, any option requires especially thorough floor cleaning before moving.

Here you cannot say: "take felt, it will forgive everything." On the contrary, felt can hold a hard particle.

Question 4. Is silence important during slight displacement?

If yes, FUR-027 gets an additional argument.

Question 5. Do you need to frequently reach the socket behind the dresser?

If yes, FUR-021 is more convenient for the stated function.

Question 6. The dresser is very light and the drawers are stiff

If yes, too-light sliding needs to be checked especially carefully. When opening, the body should not move.

Question 7. The parquet is expensive and recently restored

Then the decision is not made by the price of the glider. A test of both options is done on a hidden area, and the parquet master's recommendations are taken into account.

Scenario: a heavy oak dresser with six drawers

Imagine a massive body filled with linen, documents, and textiles.

It stands against the wall and is moved back about 250 mm every week for cleaning.

What happens without a suitable FUR

The user first applies a lot of force.

The dresser jerks out of place.

Why FUR-021 looks stronger here

Its sliding function directly matches the recurring scenario.

What still needs to be done

Before each move:

• remove the sand;

• check the trajectory;

• move the body evenly;

• do not pull by one top corner.

Why FUR-027 is not completely excluded

If a real test shows that felt slides smoothly enough and the owner values soft contact more, it is also possible.

But the choice must be confirmed on a fully loaded dresser.

Scenario: a light beech cabinet that is moved once every six months

Here the situation is the opposite.

The furniture is light.

Rearrangement is rare.

The main priority is smooth contact with the floor.

FUR-027 looks more logical.

Why FUR-021 may be unnecessary

Ease of sliding provides almost no daily benefit.

And the furniture itself may shift slightly more easily under accidental lateral force.

Scenario: the dresser stands next to the balcony door

Street sand more often ends up on the floor.

Main risk

It's not the material of the foot pad, but the dirt.

What to do

Vacuum the movement path specifically before moving.

Which FUR to choose

After the local test.

In such a zone, the felt needs to be inspected more often.

Scenario: the dresser in the bedroom, where there is almost no sand

Operation is gentler.

Here, FUR-027 gets a calmer mode.

Scenario: the robot vacuum regularly drives under the dresser

Under furniture, there is less accumulated dust, but this does not guarantee the absence of sand grains.

Additional factor

The robot may hit FUR or legs if the clearance is small.

This needs to be checked separately.

Scenario: parquet with pronounced texture

The surface is not perfectly smooth.

FUR-021 may slide differently than on a polished board.

FUR-027 may collect particles from the relief faster.

Solution

Test.

Scenario: the oiled parquet was recently refreshed

After applying the oil, the coating manufacturer may recommend a certain period before full use.

The article does not specify this period.

Before it ends, do not conduct tests with heavy furniture without the master's permission.

Why FUR should not touch the fresh floor with a random edge

The mounting foot must stand level.

If the screw is tightened at an angle and the foot is tilted, the actual contact area decreases.

This increases local pressure.

How to check the FUR installation on MN-227

After installing one leg:

1. place it on a flat reference surface;

2. ensure that the thrust pad rests with its entire working surface;

3. check that there is no rocking;

4. repeat for the remaining three.

Why four identical FURs can wear differently

A dresser is rarely loaded perfectly symmetrically.

For example:

• heavy documents in the bottom left drawer;

• light textiles on the right.

One pair of supports receives more load.

What to do

During maintenance, compare all four, not just the visible front one.

Mass of the dresser and contact area: why pressure cannot be calculated by the 70×70 dimension

After installing FUR, the actual contact with the floor is determined by the area of the support pad, not the entire wooden leg.

But the article does not calculate the allowable pressure, because for that you need:

• actual mass of the furniture;

• mechanical properties of FUR;

• properties of the parquet;

• load distribution.

You cannot independently invent a "maximum kg per one FUR."

Why oiled parquet especially requires careful cleaning

The oiled surface is often valued for its natural look and tactile feel.

But on it, a local mechanical scratch may be noticeable precisely as a disruption of texture and reflection.

Good news

Local repair of oil finishes is possible in some systems.

But that's not an argument to scratch the floor

It's better to prevent the defect.

How to move a dresser on FUR-021

Before moving

Clean the floor.

Then

Close the drawers.

Move with both hands

By the frame, not by the front of one drawer.

Do not turn sharply

It's better to first slide, then carefully change direction.

How to move the dresser on FUR-027

Same technique.

Additionally, it's useful to make sure the felt is clean before moving.

Can the dresser be lifted and moved

If the weight allows and it's safe — this method avoids prolonged sliding.

But heavy furniture should not be lifted alone if there is a risk of injury or damage to the frame.

When should the thrust pad be replaced preventively

Not by the calendar.

But by condition.

Signs for FUR-027

• the felt is worn out;

• it has become stiff;

• clogged with dirt;

• part of the fiber has peeled off;

• the self-tapping screw is loose.

Signs for FUR-021

• the working surface is damaged;

• there is a deep scratch;

• the element is skewed;

• the fastening has loosened.

Why “not scratched yet” is a poor maintenance criterion

A floor defect appears at the moment when it is already too late to replace the glider retroactively.

The inspection should be preventive.

Buy unpainted wooden legs: when MN-227 finish is related to floor care

If you need order four wooden legs MN-227.

How to place an order with felt FUR-027

MN-227 / 145×70×70 mm / beech or oak / Prestige / 4 pcs. + FUR-027 / card 25×25×5 mm / 4 working pcs. / oiled parquet / priority soft contact and rare quiet movement / reserve FUR ___ pcs.

Node passport "MN-227 + parquet"

Such a passport is useful not only during initial installation.

In a few years, it will be clear which accessory was on the furniture and why.

Mistakes when choosing a floor protector for MN-227 on parquet

Mistake 1. Choosing FUR-027 only because felt is soft

Why it happens: soft material is perceived as absolute protection.

Consequence: sand gets stuck in the felt, and it becomes an abrasive.

How to prevent: regular inspection and a clean floor.

Mistake 2. Choosing FUR-021 only because it is more expensive

Why it happens: price is perceived as an indicator of "better."

Consequence: the buyer gets too easy sliding where furniture is barely moved.

How to prevent: choose according to the mode.

Mistake 3. Considering FUR-021 a guarantee of no scratches at all

Why it occurs: the card indicates movement without damaging the floor.

Consequence: sand and the condition of the coating are ignored.

How to prevent: test and clean.

Mistake 4. Not inspecting FUR-027

Why it occurs: felt seems eternal.

Consequence: a worn, dirty surface continues to contact the parquet.

Mistake 5. Mixing two types on one dresser

Why it occurs: different FURs remained.

Consequence: uneven resistance and wear.

Mistake 6. Using one glider as a leveling shim

Why it happens: the dresser wobbles.

Consequence: legs end up at different heights.

How to prevent: address uneven floors with a separate system.

Mistake 7. Not cleaning the floor before the first move after renovation

Why it happens: the room seems already cleaned.

Consequence: construction debris remains under the furniture.

Mistake 8. Pulling a loaded dresser by one side

Why it happens: it's easier to grab.

Consequence: body misalignment and uneven load.

Mistake 9. Moving furniture with open drawers

Why it happens: need to quickly get something behind the dresser.

Consequence: the center of gravity shifts and the risk of tipping increases.

Mistake 10. Buying MN-227 before checking the top mounting

Why it happens: the article is about the floor and attention goes downward.

Consequence: the leg does not fit the bottom.

Mistake 11. Automatically choosing oak MN-227 because of oak parquet

Why it happens: the same wood species seems mandatory.

Consequence: the furniture finish does not match the body.

Error 12. Not accounting for the rug in front of the dresser

Why it occurs: the legs stand on the parquet in the normal position.

Consequence: during movement, the front FURs hit a different surface.

Error 13. Not keeping the spare FUR clean

Why it occurs: it's a cheap trifle.

Consequence: the new element is already contaminated with metal dust.

Error 14. Leaving wet felt after cleaning

Why it occurs: the floor was wiped around the furniture.

Consequence: the working surface changes its state.

Error 15. Not checking stability after installing the sliding FUR

Why it occurs: all inspection is focused on scratches.

Consequence: a light chest of drawers may shift when opening a drawer.

Error 16. Treating the nominal 5 mm as an exact addition to the furniture height

Why it occurs: the card shows C=5 mm.

Consequence: incorrect final height.

How to prevent: measure the assembled unit.

Error 17. Screwing FUR near the edge of the leg without marking

Why it occurs: it is more convenient to hold the screwdriver.

Consequence: asymmetric contact or risk of damaging the wood.

Error 18. Replacing one heavily worn felt pad without checking the others

Why it occurs: there is only one visible defect.

Consequence: the set remains uneven.

When another type of furniture leg is better than MN-227

MN-227 is not a universally best leg for parquet.

It is suitable if:

• height 145 mm is needed;

• geometry 70×70 matches the cabinet;

• the design is acceptable.

Another model is better to compare if:

• an adjustable unit is needed;

• the furniture should be lower;

• the body has a different mounting position;

• a different style is required.

Category buy legs for a dresser, wardrobe, and nightstand useful precisely in this case, not as an SEO insertion.

When FUR-021 is stronger: a brief buyer profile

Choose it as the primary candidate if:

• the dresser is moved regularly;

• it is heavy;

• the parquet surface is smooth;

• controlled movement start is important;

• The floor is kept clean;

• Too light a shift of the body when opening drawers is not noticeable.

When FUR-027 is stronger

It looks preferable if:

• furniture almost always stands;

• movement is rare and short;

• soft contact is important;

• silence is important;

• the owner is ready to periodically clean the felt;

• the test on specific parquet has been passed.

When the choice between them is not the main question

If the dresser doesn't need to be moved at all for cleaning.

MN-227 at 145 mm height can create enough clearance to vacuum under furniture.

Then the primary task is protecting the floor in a static state.

Why this needs to be checked before purchasing FUR-021

The buyer may choose the sliding option for weekly cleaning, but after assembly realize that the vacuum cleaner passes freely under the cabinet anyway.

In this case, the furniture is actually moved once a year.

The operating mode changed even before the first use.

Quick decision matrix for a specific dresser

If after a long comparison it's still hard to choose, reduce the object to four parameters.

The matrix intentionally does not contain a row for “better for parquet.” For a specific oiled floor, there is no such universal guarantee.

What to choose for the original scenario of this article

If the dresser on MN-227 is indeed moved regularly for cleaning, not just once or twice a year, I would primarily test FUR-021. Its functional logic matches the task more precisely: the furniture needs to be shifted in a controlled manner, without jerking it off its place with a heavy pull.

If after assembly it turns out that cleaning under the dresser is easy without moving it, the initial condition changes. Then FUR-027 becomes a stronger candidate: the need for regular sliding disappears, and soft contact comes to the forefront.

Why the decision should be reconsidered after the first week of use

Before assembly, dimensions and price can be calculated precisely, but the real behavior of the furniture only shows in the room. After several drawer openings and the first cleaning, it is useful to check:

• whether the cabinet shifts on its own;

• how easy it is to move it aside;

• whether the FUR work surface remains clean;

• whether there are marks on the parquet;

• whether it is convenient to return the dresser exactly to its place.

If the chosen option performs worse than expected, replacing four glides is significantly cheaper than continuing to use it until the floor is damaged.

Check after one month

After a few weeks, it is useful to inspect all four contact points again. By this time, it is already visible how the dresser behaves with normal loading, whether dust accumulates under the furniture, and whether the glides wear evenly. Such a re-inspection is especially valuable for felt: a hard particle can get into it even after a perfectly clean initial installation. For FUR-021, check the integrity of the sliding surface and the absence of deep damage. If one element noticeably differs from the others, find out the cause before the next furniture move.

FAQ

What is the size of MN-227?

145×70×70 mm.

Is there an MN-227 in beech?

Yes. Price at the time of check — 1,710 ₽.

Is there an MN-227 in oak?

Yes. Price — 2,040 ₽.

What is the sanding quality of MN-227?

"Prestige".

What glides does the MN-227 card recommend?

FUR-021 and FUR-027.

What is the size of FUR-021?

19×19×5 mm.

How is FUR-021 attached?

With a self-tapping screw; the card indicates a complete 3.5×20 mm screw.

What is SUPER GLIDE?

This is how the manufacturer designates the FUR-021 series with a special sliding coating for easier movement of furniture.

What is the size of FUR-027?

In the current card's table — 25×25×5 mm, although the name indicates d=24 mm.

How is FUR-027 attached?

The card indicates a complete universal self-tapping screw 3.5×20 mm.

What is better for oiled parquet — FUR-021 or FUR-027?

There is no universal answer. For a regularly moved heavy dresser, FUR-021 looks stronger; for rare soft contact, FUR-027. Both need to be tested on the specific surface.

Can I move a dresser on FUR-021?

Light movement is indeed one of the stated functions of FUR-021. But the floor and the glides must be clean.

Can I move furniture on FUR-027?

Yes, but the felt needs to be kept clean and solid particles must be controlled.

Can dirty felt scratch parquet?

Yes, if it contains a hard abrasive particle.

Can FUR-021 scratch the floor?

If a hard particle ends up under the working surface, the risk also exists.

Do felt glides need to be replaced?

When worn, damaged, or contaminated in a way that cannot be safely removed.

How often should they be checked?

There is no universal timeframe. It is convenient to do this during each deep cleaning, when the dresser is already moved aside.

How many glides should I buy for four MN-227?

Four working ones of the same type.

Is a reserve needed?

You can add 1–2 if it is convenient for maintenance.

How much do four FUR-021 cost?

520 ₽ at the time of checking.

How much do four FUR-027 cost?

220 ₽.

What is the difference for the whole dresser?

300 ₽.

How much does a set of four beech MN-227 with FUR-021 cost?

7 360 ₽.

And with FUR-027?

7 060 ₽.

How much does an oak set with FUR-021 cost?

8 680 ₽.

With FUR-027?

8 380 ₽.

Does beech or oak affect the choice of floor protector?

The main criterion for FUR is the floor and usage. The wood type is chosen based on furniture and finish.

Can I install two FUR-021 and two FUR-027?

For a regular dresser, it is better to use one type on all four legs.

Can FUR-021 or FUR-027 level an uneven floor?

No. They are not adjustable supports.

Do I need to clean the floor before moving?

Yes. This is one of the most important preventive measures.

What to do if the dresser is very heavy?

Do not drag it abruptly and unload it if necessary. For very heavy furniture, you should separately assess a safe way to move it.

Can I test FUR on a spare parquet board?

Yes. This is one of the best ways to reduce the risk to the visible floor.

Can I not move the dresser at all?

If cleaning is accessible under the body, this may be a safer mode.

Where to buy wooden furniture legs?

In the general catalog of STAVROS wooden furniture supports.

Where can I buy legs specifically for the dresser?

In the category for application to dressers, wardrobes, and cabinets.

Where to buy MN-227?

In the exact card for MN-227.

Where to buy FUR-021?

In the card for the round foot pad FUR-021.

Where to buy FUR-027?

In the card for the felt foot pad FUR-027.

How to order MN-227 together with foot pads?

Specify four MN-227, material, one selected FUR type, and the quantity of working/spare accessories.

How to check the current price?

Open the cards before payment: prices and stock levels change.

Final algorithm for selecting FUR for MN-227 on parquet flooring

1. Confirm MN-227 145×70×70 mm.

2. Confirm four supports according to the dresser design.

3. Choose birch or oak.

4. Record the type of parquet and its finish.

5. Check whether the coating polymerization/drying is complete according to the manufacturer's instructions.

6. Understand whether the dresser needs to be moved for cleaning at all.

7. If yes, determine the frequency.

8. Estimate the mass of the filled furniture.

9. Check FUR-021 19×19×5 mm.

10. Check FUR-027 25×25×5 mm according to the card table.

11. Perform a test on a hidden area or a spare board.

12. Compare the effort of movement.

13. Compare the noise.

14. Inspect the coating.

15. Check the stability of the dresser when opening drawers.

16. Select one type of FUR for all four legs.

17. Check the attachment point on MN-227.

18. Install all elements identically.

19. Check for absence of rocking.

20. Decide whether a reserve of 1–2 FUR is needed.

21. Record the care rules.

22. Check current prices.

23. Check availability.

24. Create one specification "MN-227 + FUR".

25. After installation, re-inspect the parquet after the first movements.

Conclusion

For a chest of drawers on four MN-227, the question "FUR-021 or FUR-027" cannot be resolved by the principle of sliding versus soft in isolation from use.

MN-227 is already selected: 145×70×70 mm, beech or oak, "Prestige". The card for the leg itself recommends both accessories, so the choice is truly not between "fits / doesn't fit", but between two modes of contact with the floor.

FUR-021 19×19×5 mm from the SUPER GLIDE series makes more sense where the chest of drawers regularly needs to be moved a bit. Its stated advantage is easier sliding of heavy furniture. For weekly cleaning, access to an outlet or cables, this is a practical function.

FUR-027 is the felt option; the card table shows 25×25×5 mm. It is more interesting where furniture mostly stands, and rare shifts should be soft and quiet.

But felt cannot be considered an automatic guarantee for parquet. It collects dust and can hold a grain of sand. Sliding FUR-021 also does not eliminate the risk of abrasives. Therefore, the main protective mechanism is a clean floor, a clean glider, and controlled movement.

On oiled parquet, it is especially wise to first test both accessories on a hidden area or a spare board. This way, you can assess the actual effort, sound, and mark on the specific floor system, rather than making a conclusion based on the product name.

Price should hardly influence the decision. Four FUR-021 cost 520 ₽, four FUR-027 cost 220 ₽. The difference is only 300 ₽. A set of four beech MN-227 comes to 7,360 ₽ or 7,060 ₽; oak — 8,680 ₽ or 8,380 ₽.

It is much more important to understand whether the chest of drawers needs to be moved regularly at all. If the 145 mm height allows easy cleaning under the body with a vacuum or robot, moving may become a rare service operation. Then the argument for FUR-021 weakens, and soft FUR-027 becomes more interesting.

However, if the dresser is full, heavy, and really has to be moved aside every week, FUR-021 gains a strong advantage in purpose — provided the surface is clean and the furniture's stability is checked.

Do not mix FUR-021 and FUR-027 on the same dresser, use them as leveling shims, or consider them protection against tipping over. These are contact fittings; the stability of the body and the top mounting MN-227 are addressed separately.

After checking the operating mode, you can buy furniture legs MN-227 145×70×70 mm and order either four FUR-021 or four FUR-027 for the four supports — not by price, but by how exactly this dresser will live on a specific oiled parquet floor.