Buy wooden furniture legs: MN-204 without coating or MN-204M with ready finish — what to choose

Comparison of one geometric model in two purchase formats: for custom finishing or with a ready-made coating

Geometric Furniture Leg MN-204

from 26.35 $

Geometric furniture leg MN-204M

from 33.79 $

Go to Catalog

MN-204 or MN-204M: short answer

MN-204 is worth buying when furniture is painted or tinted to a custom design and the legs must exactly match the body, fronts, moldings, and handles. The unpainted support can be prepared and finished simultaneously with the entire furniture, use your own RAL or NCS, perform a test coat, and maintain one technique for subsequent repairs. MN-204M is better to choose when a suitable ready-made color has already been found and the furniture needs to be assembled without a separate painting stage. The confirmed size of the finished version is 125 × 81 mm. It is especially convenient for a single cabinet, dresser, or small wardrobe when your own paint booth and complex custom finishing are not needed. You should compare not the prices of the two cards, but the total cost: MN-204 plus primer, finish, consumables, labor, and drying versus MN-204M with a proven ready-made coating.

Buy unpainted leg MN-204 Buy finished leg MN-204M Buy wooden furniture legs Buy wooden legs for painting Buy ready-made furniture legs

MN-204 is supplied without a ready-made finish coating. It is chosen for custom painting, tinting, or another agreed finishing system.

MN-204M comes with a ready finish. The current palette, material, and availability of a specific combination must be checked directly in the product card.

The confirmed size of MN-204M is 125 × 81 mm. The profile has a wide square top, a recess underneath, and a smooth concave taper.

The exact dimensions of MN-204 must be checked in the product card and DWG. Parameters of the finished version cannot be automatically transferred to an unfinished one solely due to similar article numbers.

The load per leg is not confirmed. The number of supports, central support, bottom reinforcement, and attachment method are determined by the furniture body design.

The finished coating does not cancel incoming inspection. Before installing MN-204M, check the shade, surface, and matching of all legs in the set under daylight and artificial light.

Wooden furniture legs can be purchased in two fundamentally different ways. The first is to buy a ready-made geometric shape without finish and include it in the overall furniture manufacturing cycle. The second is to choose an already painted or tinted version that does not require a separate painting operation. The difference seems small only until the buyer starts counting materials, time, test coatings, the risk of defects, and the possibility of subsequent repairs.

MN-204 and MN-204M belong to the same design logic but solve different organizational tasks. An unpainted leg gives freedom: it can be matched to the facade in the exact project color, replicate the body tinting, create a patina or multi-layer finish. The ready-made MN-204M shortens the path from delivery to assembly and removes some of the responsibility for painting, but limits the choice to the palette on the card.

For one bedside table, a ready-made coating is often more rational: ordering separate primer, enamel, consumables, and drying four small parts can be disproportionate to the task. For a series of twenty dressers, the situation changes: a furniture workshop can finish all legs simultaneously with the bodies and achieve a uniform color for the entire batch.

If the color has not yet been approved or an exact match to the furniture project is required, you can order MN-204 for the furniture project. When a suitable ready-made option has already been chosen, it is easier to buy a set of MN-204M and focus on marking, fastening, and checking the body.

Watch video ...

What does the version with the letter M mean

In this pair, the letter M denotes a ready-made version of the model with a finish coating. It helps the buyer distinguish a leg that requires its own finishing from a product whose appearance is already formed. However, the letter should not be used as a universal rule for any catalog item: the specific condition is always checked on the card.

Our factory also produces:

RPU-032 Molded Decoration

from 5.73 $

Marseilles Table 002-004

from 1,116.70 $

Wooden Decor N-486

from 17.32 $

Decor Set C.VRS-056

from 634.10 $

Chester Table 002-012

from 1,151.46 $

Wooden decor N-497L

from 7.20 $

Polyurethane molding NPU.VRS-003-2.1L

from 16.96 $

Wooden Decor N-502

from 17.44 $

View Full Product Catalog

MN-204 — blank for custom finishing

The customer receives a geometric wooden support without a ready decorative-protective finish. This is not a defect, but a different configuration format. It allows the legs to be included in the same technology as the furniture body.

MN-204M — finished surface

Separate painting is usually not needed if the selected color and condition suit the project. Before installation, the set is still checked because the actual shade depends on the material, lighting, and characteristics of the specific batch.

Same name does not cancel geometry check

MN-204M is confirmed in size 125 × 81 mm. The size of MN-204 needs to be opened in the card or DWG. You cannot drill the body according to the M-version drawing without ensuring that the mounting parameters actually match.

Different product route

For MN-204, the finishing stage begins after purchase. For MN-204M — incoming inspection and installation. Therefore, timelines, cost, and responsibility are distributed differently.

Different repair logic

An unpainted leg, finished together with the furniture, is easier to repair using the saved custom technology. For MN-204M, a compatible compound and exact match of the factory shade will be needed, or replacement with the same ready-made support.

Confirmed characteristics and verification parameters

The table shows the main feature of the pair: it is not a comparison of two different silhouettes, but a choice between the freedom of custom finishing and a shorter production cycle. Therefore, the buyer needs to assess their own resources — the availability of a painting area, an approved color, drying time, and the ability to achieve a uniform finish on all legs.

MN-204 and MN-204M: full-cycle comparison

MN-204 without coating: when freedom of finishing is really needed

Unpainted MN-204 is not intended for a buyer who just wants to "save on coating", but for a project where the color and texture of the legs should be part of the overall furniture technology. This format is especially useful for a workshop, designer, and manufacturer who already work with a specific enamel, stain, oil, varnish, or multi-layer decorative system.

Exact match to the facade color

When the body, doors, moldings, and legs are painted in one batch, it is easier to get a uniform shade and the same degree of gloss. The difference between the two materials can still affect the result, so a test remains mandatory, but the overall process is controlled by one contractor.

Custom RAL or NCS

A ready palette rarely covers all project colors. If the client has approved a specific code, it is more logical to choose MN-204 for custom finishing and perform a test swatch next to the facade.

Tinting to match the countertop or cabinet body

An unpainted wooden leg allows you to select a shade to match natural countertops, veneer, or solid wood. But the finish on the leg and on a large surface may look different due to grain direction and shape. The sample must be viewed on the actual geometric part.

Patina and multi-layer effect

The recess and concave taper of MN-204 create areas where patina and shadow are especially noticeable. This effect requires manual adjustment and should not be described as a guaranteed result without a test element.

Serial production

If the workshop produces dozens of identical cabinets, in-house painting may be more convenient than ready-made legs. All parts go through one technology, and spare legs can be stored without coating and finished when needed with the same system.

Repair after several years

A saved finish map — primer, color code, varnish, gloss level, and sequence of operations — helps restore a damaged leg. If the technology is not recorded, the advantage of custom painting is lost.

Commercial choice

For a project with a custom color, you can Buy unpainted leg MN-204, and to compare other shapes — look at unpainted furniture legs.

MN-204M: when a ready finish shortens the path to assembly

MN-204M is chosen when the ready color matches the furniture and there is no point in organizing a separate painting stage. The confirmed size of 125 × 81 mm makes the model a compact geometric support for a chest of drawers, cabinet, wardrobe, and other modern furniture, but suitability for a specific body is determined not only by height.

Small set

A single cabinet requires a limited number of legs. Buying primer, paint, and consumables just for four parts may be inefficient. Ready-made MN-204M allows you to focus on marking and fastening.

No painting booth

A quality finish requires controlled preparation and drying. If the workshop handles assembly but not painting work, factory-coated furniture leg reduces organizational complexity.

Limited project duration

The finished surface eliminates priming, interlayer processing, and process drying. However, the delivery time, availability of the required quantity and shade still need to be checked before planning assembly.

Contrasting support

MN-204M does not have to match the cabinet. A dark leg under a light cabinet or a neutral support under a wooden chest can become a deliberate accent. The main thing is to check the physical color next to the furniture.

Predictable appearance before ordering

The finished finish is easier to coordinate with the client if a real sample is available. Visualization shows the idea but does not guarantee color matching. It is better to look at the leg in daylight and evening lighting.

Quick replacement

If the same finish is available, a damaged support can be replaced without repeated painting work. However, the shade of another batch may differ slightly, so it is reasonable to keep a spare for the project.

Commercial choice

For quick assembly, you can Buy finished leg MN-204M or choose the color and coating among other ready-made supports.

Size 125 × 81 mm and geometry MN-204M

The confirmed size of the finished version is 125 × 81 mm. The height of 125 mm lifts the furniture above the floor and changes the overall silhouette. The 81 mm size refers to the maximum transverse dimension, but the exact layout, mounting part, and attachment points should be checked in the product card.

Wide square top part

It visually connects the leg to the body and creates a stable base shape. This is not a confirmation of the permissible load or a specific method of attachment.

Recess under the top part

The shadow line separates the support from the body and makes the geometry more expressive. When painting MN-204 yourself, this area is particularly sensitive to drips and unpainted spots.

Smooth concave taper

It lightens the massive top part and makes the leg modern. The finished coating should be uniform at the transition, and during manual finishing, the tool should pass without material buildup.

Height and base

Before ordering, check how 125 mm affects the furniture height, door position, wall baseboard, and cleaning feasibility. The leg should not conflict with the existing base.

Size MN-204

The unpainted version cannot automatically be considered fully identical in all parameters. Before cutting the body and purchasing fasteners, open the product card, DWG, or request an up-to-date drawing.

Why identical shape does not mean identical purchase scenario

The leg design may be similar, but the production route determines more than the external silhouette. MN-204 is included in the chain: preparation — sample — finish — drying — inspection — installation. MN-204M goes through the chain: color selection — batch check — installation — maintenance.

Different risk points

For MN-204, the risk is related to the quality of preparation and finishing. For MN-204M, it is related to incorrect selection of the finished shade, surface damage during transport, and possible differences in reorders.

Different responsibility

The finish executor is responsible for the color of MN-204. The assembler or customer is responsible for selecting a specific finished version of MN-204M. In both cases, written sample approval is required.

Different timelines

An unpainted leg may be available earlier, but the furniture is not ready for assembly until the finish is complete. The finished version saves painting time, but the availability of the desired color may affect delivery.

Different cost of error

Four incorrectly painted legs can be redone, but that takes time and materials. Unsuitable finished legs will have to be replaced or the furniture's color scheme reconfigured.

When self-painting MN-204 is beneficial

Self-painting becomes beneficial not because an unpainted leg necessarily costs less than a finished one, but because the finishing process already exists in the project. If the workshop simultaneously primes and paints cabinets, facades, moldings, and handles, adding legs to the common batch does not require separate organization. Costs are distributed across the entire furniture set.

Furniture is manufactured in series

For ten or twenty identical dressers, one test paint and one process card work for the entire batch. The legs undergo preparation together, and color control is performed against a common standard. In such a situation, MN-204 helps maintain a uniform finish and not depend on the ready-made palette.

The customer requires an exact color code

When a specific RAL or NCS is specified in the project, the finished leg is only suitable if there is a complete match. A slight difference in shade is especially noticeable if the legs are next to a painted plinth or facade. The unpainted version allows you to replicate the furniture system, but the result is still checked on a physical sample.

Complex decorative finishing is required

Patina, multi-layer enamel, aging effect, local darkening of the recess, or a combination of transparent and opaque layers require manual work. The finished MN-204M is not intended for automatic repainting: the new coating may adhere poorly to the factory finish and alter the surface geometry.

The finish must match other wooden parts

Legs can be finished together with furniture handles, moldings, and decorative overlays. A single batch does not guarantee absolute identity of different materials, but it reduces the risk of differences in gloss and tone.

The workshop stores process cards

The advantage of MN-204 is realized when the process is documented. If the compositions, proportions, and modes are not recorded, it will be difficult to repeat the color in a year. An unpainted leg without a preserved technology does not ensure automatic repairability.

There is space for drying and control

Painting a small three-dimensional part requires a hanger or support, access to all sides, and a protected space for drying. If such conditions are not available, the finished MN-204M may be more rational even for an individual project.

When the finished finish MN-204M saves more

Ready-made coating is especially advantageous where a painting cycle would have to be created just for a few legs. Savings come not only from paint, but also from preparation, drying, inspection, workspace cleanup, and the risk of rework.

One bedside table

Four ready-made supports can be inspected, installed, and handed over to the customer. For MN-204, separate materials and time would be required. If a suitable shade is found, MN-204M shortens a disproportionately long process.

Repair of ready-made furniture

When the body is already painted and supports need to be replaced, matching the old color can be difficult. A ready-made contrasting leg can become a deliberate new accent without requiring intervention on the facades.

Urgent assembly

If the project is time-constrained, skipping priming and drying helps move to assembly faster. However, the ready-made version should be ordered in advance and the availability of the required quantity should be checked.

No finishing specialist

Self-painting without experience can result in drips, dust, uneven gloss, and differences between the four legs. Ready-made MN-204M reduces this risk, although the surface still needs to be inspected upon receipt.

A predictable result is needed for the client

It is easier to agree on a physical sample of the finished color before assembly. The customer sees the real surface, not a promise of the future finish. This is especially convenient for ordering a small set online if the sample can be evaluated in advance.

How to calculate the total cost of MN-204

The price of an unpainted leg is only the first line of the estimate. The full cycle includes materials, working time, a test, possible rework, and storage of parts until complete drying. For a fair comparison, each item must be recorded separately.

The cost of the batch itself

The number of supports is multiplied by the current price of MN-204. The number is determined by the cabinet design, not by the usual rule of "four legs for any item."

Preparatory materials

Abrasives, dust removal, primer, and means for protecting mounting areas may be required. The specific composition depends on the chosen technology and leg material, so a universal list is not assigned.

Finishing materials

Enamel, stain, oil, varnish, or another system is purchased considering tests and technological consumption. The cost cannot be calculated only by the volume that will physically remain on four legs: part of the material goes to setup and application.

Specialist's work

It is necessary to account for preparation, application of multiple layers, interlayer treatment, drying, and control. The geometric recess and concave taper require careful work from all sides.

Test paintout

It increases initial costs but reduces the risk of ruining the entire batch. For serial furniture, the sample is distributed over a large number of items; for a single cabinet, its share is more noticeable.

Risk of defects

It is impossible to pre-assign a universal percentage. The workshop evaluates its own technology and adds a reserve for damage, uneven color, or a failed test element.

Drying and storage

Parts take up space and must not touch each other. The timeline of a furniture project includes not only active work but also technological pauses.

Total cost formula

Preliminary: price of MN-204 × quantity + preparation + finishing materials + labor + test coating + possible reserve. Only this amount is compared with the finished batch of MN-204M.

How to calculate the total cost of MN-204M

The finished leg looks simpler in calculation, but the estimate is not limited to the card price. It is necessary to account for delivery, shade verification, possible stock, and fasteners if they are not included in the confirmed configuration.

Price of the finished version

A specific color and the required quantity are selected. Different finish options may have different conditions, so the actual item should be compared.

Physical sample

If the shade is critical, the cost of a sample or one control leg is justified. It allows you to see the coating next to the facade and avoid returning the entire batch.

Replacement stock

For serial furniture, it is useful to keep several supports in the same finish. The exact quantity depends on the project scope and reorder conditions.

Incoming inspection

Inspection time is also part of the process. You need to check color consistency, absence of damage, geometry, and compliance with the ordered quantity before installation begins.

Total cost formula

Price MN-204M × quantity + delivery + control sample + reserve + installation materials, if purchased separately. The finished coating reduces the painting part but does not make the project free in terms of time.

How to compare timelines of two options

MN-204 starts earlier, ends later

An unpainted leg can be ordered before the final color approval, but it cannot be installed until the finish is complete. This is convenient if the furniture is going through a long production cycle anyway.

MN-204M is faster only if the required configuration is available.

If the selected color is available and suitable for the project, assembly is faster. If the shade has to be waited for or changed, the advantage is reduced.

A sample is needed in both cases.

For MN-204, a color swatch is made. For MN-204M, a physical finished sample is checked. Skipping the sample saves time only until the first mistake.

Serial production changes the calculation.

Simultaneous painting of a large batch can be efficient. For a single cabinet, the same process becomes disproportionately long.

Individual RAL or ready-made palette.

Color selection is not just a decorative decision. It determines the ordering method, quality control, and repairability. An individual code provides freedom, while a ready-made palette simplifies production.

Exact match with the body.

It is more convenient to paint MN-204 together with the furniture. Even the same code on different coating systems may look different, so not only the marking but also the overall process is important.

Contrasting legs

MN-204M is especially convenient when the legs do not have to match the body. A dark, wood-like, or neutral ready-made shade can create an independent lower line of the furniture.

Color on screen

The monitor and photo do not guarantee a match. Lighting, display settings, and surrounding materials change perception. The physical surface must be checked.

Different batches

The natural base and finishing process may cause slight differences. For one dresser, it is better to order all legs at once, and store the spare together with the set.

How to perform a test coating of MN-204

The test coating should replicate the future technology, not be a quick application of one layer on a random area. It checks color, gloss, uniformity, and how the material collects in the recess and on the concave profile.

Use one real leg or a confirmed sample

A flat board does not show coating behavior on complex geometry. On vertical and concave surfaces, the material distributes differently.

Protect mounting areas

Paint must not reduce mounting dimensions, fill threaded holes, or interfere with fasteners. Which areas to mask is determined from the drawing of the specific leg.

Repeat all layers

Preparation, primer, intermediate processing, and finish must match the actual furniture. Otherwise, the sample does not show the final result.

Dry completely

Color and gloss change as the coating cures. Do not make a decision based on a wet coating.

Look next to the facade

The leg is placed under the cabinet or next to its sample under daylight and artificial light. This shows whether the shade matches and whether the support looks too contrasting.

Keep the reference

The approved leg is signed: article number, date, system, color code, and gloss level. It is needed for the batch and subsequent repairs.

Materials for testing and assembly can be purchased for painting and mounting legs, but compatibility of specific compounds must be confirmed according to their instructions and the material of the product.

How to choose legs for the body and facades

The leg must match not only the color of the furniture. Height, body width, visual mass, plinth position, door opening, and load transfer method are important. MN-204 and MN-204M cannot be chosen as universal decorative parts without checking the structure.

First, determine the final height of the furniture

MN-204M has a height of 125 mm. It lifts the body, changing the height of the countertop, drawers, and handles. For a bedside table, this affects convenience near the bed; for a chest of drawers, the overall proportion; for a cabinet, the gap to the ceiling.

Check the width of the upper part

The 81 mm dimension must be compared with the bottom panel and the edge offset. The leg should not protrude accidentally, intersect with the facade, or fall into a weak area of the base.

Match the shape to the furniture

The square top and concave taper suit modern geometric furniture, straight-framed facades, and minimalist moldings. If the body has thin curved lines or heavy carving, it is useful to compare alternative models.

Match the color with the handles

The legs can match the handles, contrast with them, or support the tabletop. It is not necessary to paint all parts the same, but the color scheme should be deliberate.

Check the wall baseboard

Furniture on legs can be placed closer to the wall, but the body and back should not press against the baseboard. A height of 125 mm also opens up the lower space, where the wall and floor finish becomes noticeable.

Look at the furniture as a whole

One leg in hand seems larger than under a long dresser. Make a full-size template of 125 × 81 mm, place four or six outlines under the body, and evaluate from a distance.

MN-204 or MN-204M for a bedside table

One nightstand in a finished bedroom

MN-204M is more convenient if the finished shade matches the furniture. There is no need to arrange painting just for four supports. Before ordering, you can select legs for a dresser or nightstand and compare the proportions of ready-made solutions.

A pair of nightstands for a custom project

MN-204 allows finishing eight legs together with the bodies to achieve the same color. For a symmetrical bedroom, the shade difference between the right and left nightstand is especially noticeable.

Contrasting base

Ready-made dark MN-204M can complement handles, lights, or a bed frame. In this scenario, an exact match with the facade is not required, so the ready-made palette becomes an advantage.

Height next to the bed

A 125 mm support changes the tabletop level. The nightstand should not end up too high or low relative to the mattress. The body size is recalculated before ordering.

Choice for a dresser

Compact chest of drawers

Four supports may be sufficient only with a confirmed design. MN-204M suits a quick project, MN-204 — furniture in a custom color. The placement of offsets determines stability and visual balance.

Long dresser

Four corner legs may not provide adequate support for the middle. Central or additional supports are determined by the body calculation. It cannot be guaranteed that a single MN-204 can withstand a specific load without manufacturer data and design.

Chest of drawers with heavy drawers

The load changes when pulled out. The base must be reinforced, and the supports placed under the load-bearing elements. Color and finish are chosen after the technical diagram.

Dresser for painting

MN-204 is rational if the body, fronts, and legs go through one painting cycle. For serial production, this helps achieve a uniform finish.

Finished dresser without reworking the fronts

MN-204M can become a new contrasting base. It is necessary to check the height, fastening, and whether the existing bottom can support the installation of new legs.

MN-204 and MN-204M for a small cabinet

Cabinet with hinged doors

The legs should not interfere with opening the lower fronts. After raising the body by 125 mm, the position of the handles and the gap to the floor change. For a finished project, you can choose wooden legs for the cabinet according to the visual scheme, but technical calculation remains mandatory.

Wide wardrobe

Four corner supports are often insufficient for a long body. Central support and intermediate legs may be required under vertical partitions. The number is determined by the design, not the length of the leg.

Cabinet in the color of the facade

MN-204 is more convenient to finish together with the body. The legs become an extension of the furniture and attract less attention.

Cabinet with a contrasting base

MN-204M allows you to quickly add

Separate kitchen sideboard

MN-204M is convenient if the finished color supports handles or a countertop. MN-204 is suitable for a sideboard painted together with the facades. Ideas for combinations can be viewed by going to the section select furniture legs for kitchen facades.

Island pedestal

Legs are visible from all sides, so the finishing quality is especially noticeable. The finished MN-204M is inspected all around, while the MN-204 is painted with access to all planes.

Built-in column

Exposed legs may conflict with the base and appliances. Application is determined by the furniture design. A decorative support cannot be used instead of an engineering system without calculation.

How many legs a cabinet requires

The number of supports depends on the length, depth, weight of the cabinet, location of partitions, drawers, and load. Four legs is a common scheme for a small pedestal, but not a universal rule.

Four corner supports

Suitable for a compact rigid cabinet if confirmed by the design. Legs are placed symmetrically and at the same offset from the edges.

Fifth central support

Can support the middle of a long dresser. It must transfer the load to a structural element, not just touch a thin panel.

Six or more legs

Used on long furniture when supports are placed under partitions and load zones. The layout must account for access to adjustment and cleaning.

Load when opening

Extended drawers and open doors shift the center of gravity. Check not only the furniture in a static state, but also real usage scenarios.

Spare leg is not a working support

The reserve is stored for replacement and should not be accidentally used instead of the calculated central support. The quantity in the order is divided into installation and spare.

When central support is needed

Long bottom panel

If the base can sag between corner legs, a central support reduces the span. The decision is made by the furniture designer.

Heavy drawers

The contents create a load in the middle. The support must be placed under a partition or reinforcement, otherwise it will not solve the problem.

Stone or heavy countertop

The weight of the upper part is transmitted through the body. The suitability of MN-204 or MN-204M cannot be guaranteed without calculating all elements.

Wide wardrobe

Intermediate supports are placed under vertical walls. A random leg in the center of a thin bottom can push through the material.

Uneven floor

An additional support may hang or, conversely, take on too much load. Adjustment and the base plate are selected according to the project.

How to attach wooden legs to the body

The attachment method in the SEO scheme is not confirmed as a single set for both models. Therefore, it cannot be stated that MN-204 and MN-204M are always installed on a specific plate, stud, or screws. The scheme must be taken from the card and DWG.

Mounting plate

It distributes the load and allows the leg to be removed, but must match the upper part of the support and the body. A random plate may protrude beyond the contour or not align with the holes.

Stud

A threaded connection is convenient for knockdown furniture if it is provided by the leg design. The diameter, depth, and mating part must be confirmed.

Straight mounting

Screws through the body are only possible with suitable thickness and reinforcement. The support cannot be attached to thin MDF without calculation and an embedded part.

Bottom reinforcement

The crossbar, embedded or mounting frame helps transfer the load to the body. Its size and material are determined by the furniture design.

Marking

Four supports are placed according to a template, checking diagonals and equal offsets. Even a slight shift is noticeable on the geometric shape.

Glide

It protects the floor and the bottom end, but the specific type must match the covering, load, and adjustability. The presence of a foot pad in the kit is not confirmed.

Before starting work, it is useful to open recommendations for painting and installing furniture legs and compare them with the drawing of the specific model.

Can the leg be attached directly to MDF

The answer depends on the panel thickness, material density, fastener placement, and load. MDF works well in furniture, but a point connection without reinforcement may be insufficient. A universal permission cannot be given based solely on the material name.

Check the thickness and edge

The fastener should not be too close to the edge. The top part of the leg must rest on the calculated area.

Use the mounting bracket if necessary

An additional panel or frame distributes the load. It is especially important under a long dresser and cabinet.

Do not overtighten to the point of damage

Excessive tightening can damage the wood of the leg or the body panel. The connection is checked after assembly and the first cycles of use.

Maintain access to the fasteners

The leg should be possible to tighten or replace without damaging the furniture. This is especially important for the finished MN-204M, which may be removed during coating repair.

What to buy together with MN-204 or MN-204M

Legs are rarely chosen in isolation. The buyer may need finishing materials, mounting elements, a spare support, and visual examples of furniture on wooden legs. It is important to use only confirmed categories and not to assemble fasteners by random similarity.

How not to confuse MN-204 and MN-204M with similar products

MN-204 and MN-204M are not just one product in two colors

The main difference is the stage of readiness. MN-204 requires separate finishing, MN-204M already has a coating. This changes timelines, total cycle cost, and responsibility for color.

Finished leg and hand-painted leg

Even the same shade can differ in gloss, layer thickness, and tactile feel. Two systems cannot be mixed on one dresser without a physical check.

MN-204M and a random leg 125 mm high

Matching height does not mean the same shape, top dimension, and mounting. A full drawing must be compared.

Decorative support and structural system

A beautiful profile does not replace body calculation. If a heavy cabinet or stone countertop is needed, supports are chosen together with reinforcement and load transfer scheme.

Leg and plinth

An open wooden support creates a different look and access under the furniture. It is not an automatic replacement for a solid kitchen or cabinet plinth.

Model with metal tip

MN-205.1 has a different decorative character. If metal is needed as an accent, it is better to look at a leg with a metal tipand not add a random detail to MN-204.

Practical choice for specific situations

Need to match the color of the facades

Choose MN-204 and perform a test with one system and the body. Do not rely only on the RAL code: material and gloss also affect the match.

Need one cabinet in a finished room

MN-204M is more convenient if a suitable shade is found. Physically apply the leg to the furniture and floor before ordering the entire set.

Need to manufacture twenty identical dressers

MN-204 allows painting the entire batch together with the bodies. Keep a control leg and a technical card.

The project needs to be finished quickly

MN-204M reduces the painting stage, but only if the required finish is available. Check the delivery before promising a deadline to the client.

The legs should be contrasting

The finished palette MN-204M can provide quick results. The contrast is compared with the floor, handles, and countertop, not just the facade.

The furniture will be repaired and updated.

MN-204 is more convenient if the workshop stores its own technology. MN-204M is rational when it is possible to reorder precise execution and maintain a stock.

The body is made of MDF.

First, reinforcement and fastening are designed. You cannot install a leg directly into a thin panel just because the top part looks wide.

The chest of drawers is longer than usual.

Calculate the intermediate supports. The color is chosen after the structural scheme, because the number of legs affects the visual rhythm.

One damaged support needs to be replaced.

For MN-204, the saved finish is repeated. For MN-204M, the batch and shade are checked. Sometimes it is better to replace the entire visible set if the new leg differs noticeably.

Mistakes when choosing MN-204

Consider it ready for installation

Without coating, the leg requires finishing if the project does not specify another confirmed state. Installing an unfinished part may not meet usage conditions.

Do not include painting in the budget

Primer, finish, labor, and drying can change the final cost more than the difference between cards.

Paint without a test piece

A concave shape reveals runs and gloss differences. A flat swatch does not replace testing on the leg itself.

Cover mounting areas with paint

Coating can change fit and interfere with fastening. Protective zones are determined by DWG.

Assume size based on MN-204M

The exact parameters of MN-204 need to be checked separately. Similarity of the article number is not technical confirmation.

Buy only four pieces for the long body

Quantity depends on the design. Missing central support can cause the bottom to sag.

Errors when choosing MN-204M

Choose the shade based on the photo

The screen and real light differ. A physical sample or one control leg is needed.

Consider the finished coating invulnerable

It can be scratched during transport and installation. The surface is protected until assembly is complete.

Do not order a spare

A later batch may differ. For a large set, a reserve reduces the risk of noticeable replacement.

Repaint without checking compatibility

New material may not adhere well to the factory finish. If a different color is needed, MN-204 is more rational.

Do not check fasteners and housing

Finished finish does not mean a ready-made mounting system. The connection diagram is still designed.

Expect the same shade on all screens and materials

Color is perceived next to the floor and facade. Verification in a real interior is mandatory.

Who is MN-204 suitable for

• a furniture workshop with its own painting area;
• a project with exact RAL or NCS;
• a series of chests of drawers, pedestals or wardrobes in one color;
• legs, fronts and moldings for joint finishing;
• individual wood tinting;
• patina and multi-layer decorative system;
• a project where the color is not yet approved;
• a repair strategy with a preserved technological map;
• to a customer willing to account for drying time;
• for furniture where the ready palette does not fit.

When it's better not to choose MN-204

• four legs are needed for urgent assembly;
• there are no conditions or specialist for quality finishing;
• the ready color MN-204M already fits perfectly;
• the budget does not account for materials and labor;
• dimensions and DWG have not been verified;
• the buyer expects to install the leg immediately upon receipt.

Who MN-204M is suitable for

• a bedside table or compact chest of drawers;
• a small cabinet with a ready-made body;
• an urgent project without a painting stage;
• a workshop without its own painting booth;
• contrasting legs under light furniture;
• a project with an approved physical color sample;
• furniture where the height of 125 mm is confirmed by calculation;
• a customer who wants to know the appearance in advance;
• a small batch with a uniform ready-made coating;
• a repair with the ability to keep a spare support.

When it's better not to choose MN-204M

• a precise custom RAL is needed that is not in the palette;
• the legs must undergo the same tinting as the body;
• the final shade is selected only by monitor;
• a complex patina or multi-layer finish is planned;
• the size 125 × 81 mm does not match the body;
• the buyer intends to repaint the finished surface without a test.

What to Check Before Ordering

• article MN-204 or MN-204M;
• the surface condition;
• size of MN-204 according to the card and DWG;
• size of MN-204M 125 × 81 mm;
• material of specific execution;
• actual palette of the finished version;
• physical color sample;
• number of main and spare supports;
• need for central support;
• thickness and reinforcement of the bottom;
• mounting method;
• presence of a plate, stud, or foot in the configuration;
• finished height of the pedestal, chest of drawers, or cabinet;
• baseboard, plinth, and door opening;
• cost of the complete finishing cycle;
• Delivery, drying, and assembly timelines.

Storage, care, and subsequent repair

Even a properly selected leg can lose its appearance if damaged before installation or if inappropriate care products are used. MN-204 and MN-204M require different approaches because the first receives its finish in the workshop, while the second already has a ready-made coating.

Storage of MN-204 before finishing

Unpainted parts must be kept in stable conditions, protected from moisture, dirt, and mechanical impacts. Legs should not be stacked so that the wide upper part presses on the concave narrowing of the adjacent part. Before painting, the entire set is inspected again.

Storage of MN-204M

Finished legs are best left in protective packaging until assembly. There should be no friction between painted surfaces. If the set arrives in a cold room, it should be allowed to acclimate according to the manufacturer's recommendations before unpacking and installation.

Protection during assembly

Installation tools must not touch visible edges. The cabinet is turned over onto a soft base, and the legs are tightened without using them as levers. After assembly, protection is removed only before the final inspection.

Care for the finished surface

Use a soft cloth and products compatible with the specific finish. Abrasives and aggressive compounds can alter the gloss or color. Moisture should not remain for long near the bottom end and attachment points.

Mounting control

After the first few weeks of use, check for play and stability. If the leg moves, first inspect the condition of the fasteners and body, rather than attempting to tighten the connection with excessive force.

Repair MN-204

A saved control swatch and technical card allow for local coating restoration. For noticeable damage, it is sometimes more rational to remove the leg, fully prepare the surface, and reapply the finish rather than masking the defect with random paint.

Repair MN-204M

You need to clarify the compatible repair compound or the possibility of ordering a replacement in the same finish. If the shade of the new batch differs, all visible legs of one item can be replaced with a set, keeping the old usable parts as a reserve.

It is useful to cross-check the general recommendations with the page care rules for furniture supports and coating.

How to buy MN-204 or MN-204M at STAVROS

Start not with the color, but with the furniture construction. Determine the finished body height, number of supports, presence of central support, position of partitions, and method of fastening. After that, it will become clear whether the geometric leg of this shape is suitable and whether the size MN-204M 125 × 81 mm can be used.

If the furniture is painted according to an individual project, open the card and buy an unpainted leg MN-204 after checking the exact dimensions and DWG. Include in the estimate a test paint-out, materials, work, and drying in advance.

If the suitable color is already in the current palette, go to the finished version and buy a finished leg MN-204M. Before placing a batch order, order or approve a physical sample, check the shade next to the facade, and clarify the possibility of reordering.

For furniture of complex shape, you can Order selection of legs and finish for furniture. The conditions for receiving the batch and spare products should be checked on the page Payment and delivery of furniture legs.

Ordering via STAVROS is more convenient than random selection because the buyer works with specific cards, article numbers, and confirmed availability options. This helps avoid confusing a leg meant for painting with a product that already has a finish coating.

FAQ: questions about MN-204 and MN-204M

How is MN-204 different from MN-204M?

MN-204 is supplied without a ready finish coating and is intended for individual finishing. MN-204M has a ready coating and can usually proceed to installation after checking the set.

What does the letter M in the article number mean?

In this product pair, it indicates the finished version of the model with a coating. The condition of a specific item should still be verified on the card.

Which model is supplied without coating?

MN-204. It is chosen for project painting, tinting, or other agreed finishing systems.

Does MN-204 need to be painted?

For most furniture projects, a decorative and protective finish will be required. The exact system is chosen based on the material, usage conditions, and furniture design.

Can MN-204M be installed immediately after receipt?

After incoming inspection — if color, surface, size, and mounting scheme match the project. The finished coating does not cancel the check of fasteners and housing.

What size does MN-204M have?

The confirmed size is 125 × 81 mm.

Is the geometry of MN-204 and MN-204M the same?

They belong to the same model logic, but the technical dimensions and mounting scheme cannot be considered identical without checking the cards and DWG.

How to check the dimensions of MN-204?

Open the product card, view the current drawing or DWG, and compare it with the bottom panel of the furniture before drilling.

Which is cheaper: MN-204 or MN-204M?

The answer depends on the full estimate. For MN-204, materials, labor, sample, and drying are calculated. For MN-204M — the finished price, sample, delivery, and reserve.

How to match the color of a furniture front?

It is more reliable to finish MN-204 together with the fronts and use a common test sample. The finished MN-204M should be compared with the actual front under the same lighting.

Can MN-204 be ordered for a specific RAL?

The unpainted model allows finishing in the desired system by the chosen contractor. The availability of a separate service and the specific material are clarified before ordering.

Why can't the color of MN-204M be chosen only from a photo?

The screen, lighting, and surrounding materials alter perception. A physical sample shows the shade and gloss more accurately.

How to repair the coating of MN-204M?

With a compatible compound that matches the factory finish. The exact material needs to be clarified; if there is a noticeable difference, replacing the leg may be required.

What to choose for a single bedside table?

MN-204M is especially convenient if the ready color suits. MN-204 is reasonable when the entire table is painted according to an individual project.

Which option is more convenient for a furniture workshop?

A workshop with its own painting area often finds MN-204 convenient. For production without a finishing section — MN-204M.

Do I need to buy a spare leg?

For a large batch, a spare is useful. It simplifies repairs and helps avoid differences in shades when reordering later.

How many legs does a long dresser require?

The number is determined by length, bottom construction, partitions, load, and drawer placement. Four supports are not a universal scheme.

When is a central leg needed?

When the middle of the body requires additional support according to calculations. It should be located under a structural element or reinforcement.

Can MN-204 be attached directly to MDF?

Only after checking the thickness, embedded part, and fastening scheme. A thin panel without reinforcement may be insufficient.

Is the mounting hardware included in the kit?

This is not confirmed in the available SEO scheme. The configuration needs to be checked in the card of both models.

Is a footplate needed?

It can protect the floor and the bottom edge, but the type is chosen based on coating, load, and construction. Availability in the kit is not confirmed.

Can I repaint the MN-204M?

Only after checking the compatibility of the new material with the finished coating. For an individual color, it is usually more rational to immediately choose the MN-204.

How to maintain the same color for four MN-204 units?

Paint them in one batch, prepare them identically, use the same technology, and compare with a control sample after complete drying.

How to check furniture after installation?

Place the cabinet on a level floor, check stability, diagonals, play, door and drawer opening, and then re-inspect the fasteners after the first cycles of use.

Where to buy MN-204?

In the card, you can Buy unpainted leg MN-204.

Where to order MN-204M?

In the card, you can Buy finished leg MN-204M.

Result: custom finish or ready-made surface

MN-204 and MN-204M allow using one geometric idea in two production scenarios. The unpainted MN-204 is suitable for furniture with an individual color, joint finishing with the cabinet, precise RAL, or custom tinting. The finished MN-204M in size 125 × 81 mm is convenient for a small set and a project where the appropriate shade has already been selected.

The decision cannot be made based solely on the price of the card. For MN-204, you need to calculate the primer, finish, consumables, labor, sample, and drying. For MN-204M, check the physical color, availability of the entire batch, reserve, and repairability. In both cases, first calculate the body, number of supports, and fastening, and only then select the surface condition.

STAVROS allows you to compare unpainted and finished furniture legs, explore alternative geometric models, and select materials for finishing. An informed choice helps you get a set that matches not only the style of the dresser, cabinet, or wardrobe but also the actual timelines, budget, and technology of the furniture project.